Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹34.7 LAccepted-AOC | L1 | Accepted-AOC Accepted being lowest quoting | |
| 2 | L2₹37.9 L+₹2.6 L (7.41%)Rejected-AOC | L2 | Rejected-AOC Rejected being higher quoting |
Tender Value
₹38.9 L
EMD Value
₹77,800
Closing Date
15 Oct 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Hisar
Garrison Engineer Hisar Military Station Hisar 125006
CA No GE(H)-43/2022-23 PROVN OF ADDITION AND ALTERATION OF SIX TEMPORARY HUTS OF CERTAIN UNIT IN THE AOR OF AGE B/R II UNDER GE HISAR AT HISAR MIL STN
2022_MES_552378_1
CA No GE(H)-43/2022-23
Open Tender
Civil Works
Item Rate
210 days
Hisar Mil Stn
As per Tender documents
6 documents required · 6 mandatory
₹500
GE Hisar
₹77,800
Yes
10 Nov 2022
16 Sept 2022
17 Oct 2022
16 Sept 2022
15 Oct 2022
1 Oct 2022
Amount
Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) complete, all as directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.
Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified.
Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified
Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.
Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.
Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.
Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.
Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil all as specified.
Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in soft/loose soil all as specified.
Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil all as specified.
Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick. Note :- Soil obtained from excavation under item 10.00 here-in-before shall be used for filling.
Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.
M&L for hardcore of broken stone or boulders, gauge exc. 63mm and not exc 100mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.
M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete and sub base all as specified.
M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately.
M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.
M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.
Cutting openings, through brick walls built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m all as directed.
M&L for brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.
M&L brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan exc 6.00 metre mean radius, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.
S & F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm (SIngle rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water / moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note:- stainless steel butt hinges andnecessary S.S screws shall be paid separately.
Supply & fixing 100mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified.
Supply & fixing 150mm Extruded brass handles, fabricated type polished complete all as specified.
Supply & fixing 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedall as specified.
Supply & fixing 150mm Brass flush bolt, type 2 and fixed flush all as specified.
S&F butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.
S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.
S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.
S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.
S&F Maharaja Door stoppers brass 100mm size complete all as specified and as directed. Make :- Prayag Cat Part No DSB-MH4-SS or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F vanishing blinds vertical type 100mm slot width of approved fabric and colour and powder coated aluminium top rails complete all as specified and directed.
S&F in repairs 25mm bore & 1.00mm wall thickness stainless steel fancy type decorative curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.
S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) including shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including powder coated 'D' type handle of suitable size, tower bolt of suitable size, suitable size hinges heavy grade complete all as specified & as directed. Note :- Mortice lock, Door closer & Glass panes/wire cloth shall be measured & paid seperately under relevant item of BoQ.
S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty etc complete all as specified and directed.
S&F mortice lock vertical type 8" SS, 4 lever complete all as specified and as directed. Make :- Prayag Cat Part No ML-4501/SS/P or techno commercial equiavlent of Godrej / Harrison / Link.
M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.
S&F mild steel framed work in tubular trusses using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.
S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.
S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and not exc 10 cm long and dia of neck 11mm to 15mm complete all as specified.
S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long, dia of neck not exc 12mm complete all as specified & as directed.
S&F GI powder coated snap grid of sizes 605 mm x 605 mm frame work for false ceiling with main tee 32 x 24 x 1mm thick, cross Tee 26 x 24 x 1mm and wall angle 24 x 24 x 1mm thick, flange covered with PVC thin includng hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including Gypsum board 7 -9mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 600mmx600mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified & directed.
M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)
M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to entre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.
M&L for Providing decorative POP cornices / moulding of pattern/design as approved by Engineer-in-charge of cross section area exc 13 sqcm and not exc 25 sqcm complete all as specified and directed.
S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.
S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.
Supply and fixing 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc complete all as specified.
S & F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.
M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.
M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.
M&L for glazed ceramic tiles (coloured) 1st quality, 350mm x 250mm x 7mm thick / 450mm x 350mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for vitrified ceramic tiles 1st quality (light shade), 10mm thick (square/rectangular), polished, coloured, area of each tile exceeding 0.42 sqm and not exceeding 1.00 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.
M&L for vitrified ceramic tiles 1st quality (light shade), 10mm thick (square/rectangular), polished, coloured, area of each tile exceeding 0.42 sqm and not exceeding 1.00 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for Granite (of any type) tiles 15-18mm thick machine cut, as in steps, jambs, cooking plateforms and the like, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over & including 20mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.
M&L for factory made 80mm thick machine pressed precast cement concrete coloured interlocking paver blocks glossy finish of Grade M-40 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 50mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.
M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. complete, all as specified & as directed.
M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).
M & L for rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.
M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement including mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.
M&L for complete removal of existing treatment on walls (any numbers of layers) by scrapping with steel wire brushing or any other means, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. etc and applying 2mm thick wall care putty on walls including filling cracks or holes complete and applying two coats of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.
M&L for preparation of new plastered surfaces and applying two coats of Plastic emulsion distemper of approved shade/tint over 2mm thick wall care putty on walls all as specified & as directed.
M&L for preparation of new plastered surfaces of walls and applying two coats of Exterior emulsion paint of approved shade/tint all as specified & as directed.
M&L for complete removal (any number of layers) of existing treatment by using scaffolding, ladder, cradles & other protective measures which are necessary for execution of work including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc by steel brushes or by any other suitable measures including cleaning of surfaces by spraying water and thereafter filling depressions of scrapped surfaces with 2mm thick wall care putty over plastered surfaces and applying two coats of exterior emulsion paint (Weather proof) of approved shade/tint on walls all as specified & as directed.
M&L for preparation of new decorative surfaces of ceiling incl cornices and applying two coats of oil bound distemper (OBD) of approved shade/tint all as specified & as directed.
M&L preparation of new or previously untreated plastered/ concrete surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint of approved tint over a coat of priming paint all as specified & as directed.
S&F 10mm thick toughened glass in glazing to aluminium door / window / fixed partition & like including pad/gasket all as specified and directed.
M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.
M&L for two coats of varnishing on wood or wood based materials over prepared surfaces by filler coats and sizeing complete all as specified.
M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.
Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.
S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.
Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store.
Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store.
M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.
M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.
M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall all as specified and directed.
S&F Grating doom 100 mm dia with waste hole of PTMT (Minimum weight 25 gms) all as directed.
S&F Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.
S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified.
S&F PVC waste pipe 32mm dia for urinal or wash basin etc complete all as specified and directed.
S & F 32mm bore Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm- 260gms) etc complete all as specified and directed by Engineer-in-Charge.
S&F Vitreous china white colour one piece wash down water closet pan padestal with integrated flushing cistern and seat cover complete all as specified and as directed. Make :- Prayag "CASA" Series (or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Vitreous china white colour one piece Wash basin of size 500x400x130mm complete all as specified and as directed. Make :- Prayag "MIST" Series (4705) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Vitreous china white colour Urinal Pot half stall of size 345x320x560mm complete all as specified and as directed. Make :- Prayag Cat Part No 4998 or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F flush cock (push type) 25mm dia complete all as specified and as directed. Make :- Prayag Cat Part BEA-31 or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Health Faucet square with 1 mtr tube & hook complete all as specified and as directed. Make :- Prayag Cat Part BEA-87 or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F 15mm dia chromium plated 2 way single handle bib cock with flange complete all as specified and as directed. Make :- Prayag Cat Part No 9912 (Octavia Series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F 15mm dia chromium plated single lever basin mixer W/O pop up waste system complete all as specified and as directed. Make :- Prayag Cat Part No 9851 (Dawn Series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Towel rack complete all as specified and as directed. Make :- Prayag Cat Part BA-03 (Cantabile - Picasso series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Towel rail complete all as specified and as directed. Make :- Prayag Cat Part BA-10 (Cantabile - Picasso series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F toilet paper holder complete all as specified and as directed. Make :- Prayag Cat Part BA-10 (Cantabile - Doris series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F 15mm dia chromium plated bib cock long body with flange complete all as specified and as directed. Make :- Prayag Cat Part No PIS-08H or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F soap dish with glass complete all as specified and as directed. Make :- Prayag Cat Part BA-25G (Cantabile - Angelo series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F 15mm dia chromium plated stop cock (Male thread) complete all as specified and as directed. Make :- Prayag Cat Part No 8326 or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F 15mm dia chromium plated angle cock with wall flange complete all as specified and as directed. Make :- Prayag Cat Part No 9910 (Octavia Series) or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F Vitreous china Urinal Partition slab terminating about 40cm above floor level complete all as specified and as directed.
S&F kitchen sink (overall size 610mm x 460mm x 254mm and bowl size 538mm x 375mm x 254mm or nearest higher size) ) made from high grade AISI-304 (18/8) stainless steel of 1mm thickness including 32mm bore brass CP waste coupling, plug, washer, 32mm bore and 600mm long PVC waste pipe including fixing cantilever brackets made of MS angle iron 30x30x3mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning of ends of brackets to errecting stand into wall and making good distrubed portion in CM (1:2) on in PCC (1:2:4) using 20mm graded stone aggregate and connecting union to pipe complete all as specified and directed. Make :- Prayag Cat Part No H821-D or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F square floor trap flat border (150x150mm) complete all as specified and as directed. Make :- Prayag Cat No FT-76M or techno commercial equiavlent of makes mentioned in List of makes here-in-after.
S&F salt glazed stone ware gully trap square or round mouthed type 'P' of size 150 x 150 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C-0 block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete, all as specified and as directed.
M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.
Material and labour PCC 1:3:6 type C-2 using 40 mm graded stone aggregate in concrete bed to drain pipes including forming cradles in after they are laid and tested complete for 150mm bore pipe all as specified and as directed.
S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trench or under floors complete all as specified.
S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trench or under floors complete all as specified.
S&F 110mm bore PVC (SWR) bend with access door all as specified & as directed.
S&F 75 mm bore PVC (SWR) vent cowl complete all as specified.
Taking down carefully copper/aluminum point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed.
M&L for point wiring for one light / fan point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc complete, all as specified & directed. (Note :- Switches, sockets, sunken type modular metal box, modular plates etc shall be measured and paid for separately under appropriate items of BoQ' ).'
All as per item No. 113.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board.
All as per item No. 113.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.
All as per srl item No. 113.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi strand on independent board including provn of 2.50 Sqmm unsheathed, multi stranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed.
S&F Modular switch 1 way 6A, 1 module all as specified & directed.
S&F Modular switch 1 way 16A, 1 module all as specified & directed.
S&F Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.
S&F Modular Socket, 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.
S&F Modular Bell push 6A 1 module complete all as specified & directed.
S&F Modular Fan step regulator, 120W - module all as specified & directed.
S&F white cover plate with frame 8 module all as specified & diretced.
S&F white cover plate with frame 6 module all as specified & diretced.
S&F white cover plate with frame 4 module all as specified & diretced.
S&F white cover plate with frame 3 module all as specified & diretced.
S&F white cover plate with frame 2 module all as specified & diretced.
S&F metal flush box 1/2 module all as specified & diretced.
S&F metal flush box 3 module all as specified & diretced.
S&F metal flush box 4 module all as specified & diretced.
S&F metal flush box 6 module all as specified & diretced.
S&F metal flush box 8 module all as specified & diretced.
S&F Bell ding dong type, AC, 230 Volts, single pole.
S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.
S&F LED tube light fitting 1x20W/22W, regal batten for LED including ultra bright glass LED Tubelight with very high efficacy, single / double side connection all as specified and directed. Make : Havells Regal batten Cat Part No REGALBATTENT8UPTO1X22WSSBSWH & LED tube rod Cat Part No PHOTONULTRAE2.01213T8SSTL20WLED865SPC of Havells or Surya Cat Part No SLE BT 20 MS for batten & LED tube rod Cat Part No SLE TL-DS 18 PC Reform of Surya or Cat No LTTB4F20WLEDEW BATTEN for batten & LED tube rod Cat No Cat No LT4F20WLEDT8/WDI of C&S or equivalent of makes as mentioned in Appx 'C' list of makes.
S&F LED light fitting 1x10 Watt for LED incl ultra bright glass LED tube with very high efficiency single / double side connection all as specified and directed. Make : Cat Part No LUMILINEPLUSBS10WLED8655PCSS of Havells or equivalent of makes as mentioned in Appx 'C' list of makes.
S&F concealed LED downlighter of capacity 15 Watt having extruded aluminium frame suitable for fixed in ceiling complete all as specified and directed. Make : Cat Part No GLOWDLR15WLED830S of Havells or equivalent of makes as mentioned in Appx 'C' list of makes.
S&F in replacement asesthetically designed LED street light fitting 35 Watt system wattage for energy saving having IP 66 degree of protection with minimum system efficiency as >85%, made of pressure die cast aluminum hosing powder coated in graphite grey and heat resistant toughened glass with excellent thermal management LED shold have lens optics and vandal proof prismatic poly carbonate covers for ensuring efficient optics and uniform distribution of light fitting should have operating voltage range of 120-270 Volts, THD<10%, P.F. >0.95, fitting should have in built surge protector of 5 KV and CRI>70 with CCT 5700 K and including 0.5 sqmm flexible copper multistranded conductor cable fixed on wall / pole including security light bracket made to shape out of GI pipe 40mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC of Endura Citylite Platinum Plus of Havells or TRP-400-35-57-SL-LM-NSR of Crompton or equivalent make as mentioned in Appx 'C' list of makes here-in-after.
S&F in replacement LED recess mounting panels 2 feet x 2 feet luminaire of capacity 36 watt suitable to be fixed in ceiling having extruded aluminium frame and super bright LEDs of complete all as specified and directed. Make : Surya Cat Part No SLE FP 36 R22 or Cat Part No VENUSNEOHE2X2R36WLED840PIRSENSOR of Havells or Cat Part No LTCRP36WLED2X2 of C&S or equivalent of makes as mentioned in Appx 'C' list of makes.
S&F in replacement LED recess mounting panels 1 feet x 1 feet luminaire of capacity 20 watt suitable to be fixed in ceiling having extruded aluminium frame and super bright LEDs of complete all as specified and directed.
S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 Amp SPN MCB complete all as specified. Make :- Indo Asian Cat Part No 811955 or equivalent of makes mentioned in list of makes here-in-after .
S & F sheet metal enclosure, double door type, having door earthing, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 12 way, 240 Volts. Make :- Indo Asian Cat Part No 810323 or equivalent of makes mentioned in list of makes here-in-after .
S & F MCB SP, 6 to 32 Amps 240 Volts , 'B' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.
S & F MCB SPN, 63 Amps 240 Volts , 'B' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.
Supply and fixing energy saving ceiling fan 1200mm sweep five star rated with brushless direct current motor (BLDC) asper lates IS-374-2019 having series value > 4 to < 4.5 m3/min/w and 50 Watt with double ball bearing and three blades with all accessories, down rod, two nos canopy, white in clour including 2 core 0.5 sqmm copper flexible cable for connection from ceiling rose to fan complete all as specified and directed.
Supply & fixing and testing metal body exhaust fan of 300mm sweep heavy duty, double ball bearing, 900 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete. Make : Model No Turbojet SP of Havells or Cat Part No Supreme DLX HD of Bajaj or Cat No Transair of Crompton equivalent of make as mentioned in Appx 'C' list of makes here-in-after.
S&F MS heavy duty down rod of 15mm dia and 1000mm length with necessary cutting / drilling holes and painting suitable for ceiling fans complete all as specified and directed.
S&F Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (40mmx6mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note :- Excavation & earthwork shall be measured & paid for separately.
Supply , laying , jointing, testing and commissioning of cable of size 16 sqmm 2 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors as per IS 7098 (Part-I), laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe including taking out existing u/s cable complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.
M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness afterlaying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.
M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed. .
M & L for earthing complete with galvanized iron earth plate electrode of size 60cmx60cmx6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, connected to the galvanized earth lead wire 4mm dia by means of GI bolts/nuts/ washers, protected by 15mm bore GI light grade pipe from earth plate and upto 3m along pole fixed with 2 clamps made from mild steel flat iron 25x3mm bolts, nuts and washers etc. Earth plate shall be surrounded by packed layer of coal dust 300mm and common salt 15cm thick all around bottom and top, 20mm GI medium grade pipe for watering and including funnel , wire mesh , RCC 1:2:4 type B-1 using 20 mm graded stone aggregate cover of size 30 cm X 30 cm X 8 cm thick reinforced with expanded metal weighing not less than 4Kg/Sqm, PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in earthing pit including necessary excavation and earth work, all as specified and shown in electrical plate No-3 of SSR part-I and connected to earthing point and testing on completion complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing.. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.
RAJPAL SINGH CONSTRUCTIONS
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .