Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.1 LAccepted-AOC A 3 257 JANAKPURI NEW DELHI 110058 | WEST DELHI | DELHI | 110058 | L1 | Accepted-AOC Accepted being L1 | |
| 2 | L2₹40.5 L+₹6,400 (0.16%)Rejected-Finance | L2 | Rejected-Finance Rejected being not lowest | |
| 3 | L3₹46.9 L+₹6.5 L (16.1%)Rejected-Finance RZ 212F D BLOCK RAJ NAGAR PART II PALAM COLONY NEW DELHI 110077 | SOUTH WEST | DELHI | 110077 | L3 | Rejected-Finance Rejected being not lowest | |
| 4 | L4₹47.0 L+₹6.6 L (16.3%)Rejected-Finance NO 9 BYRAVESHWARA INDUSTRIAL ESTATE ANDRAHALLI MAIN ROAD NEAR PEENYA 2ND STAGE BENGALURU 560 091 | BENGALURU URBAN | KARNATAKA | 560091 | L4 | Rejected-Finance Rejected being not lowest | |
| 5 | L5₹49.2 L+₹8.7 L (21.6%)Rejected-Finance | L5 | Rejected-Finance Rejected being not lowest |
| Sl No | Description | Qty | Unit | MV Engineers And Contractors L3 | mayur enterprises L7 | DS CONSTRUCTION L2 | Rajindera Enterprises L6 | M/s JAIMAA ASSOCIATES L5 | Vijay Electricals L4 | M/S ADHIKARI CONSTRUCTION CO. L1 |
|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Supply, installation, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , mounted on angle iron legs 50x50x6mm thick, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system accomodated with 01 No ACB 4 pole, 800 Amp, 50 KA, 415 Volt AC Horizontal draw out type motorized, front operated with Micro processor based LCD protection release for adjustable over current, short circuit and earth fault protection fitted with aluminium bus bar link 1200 Amps for incomming and outgoing cable connection. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement . including excavation, earth work and platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed sotne aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. | 2 | Each Job | 86,000 ₹1,72,000 Lowest | 4,00,000 ₹8,00,000 | 1,90,000 ₹3,80,000 | 1,50,000 ₹3,00,000 | 1,55,000 ₹3,10,000 | 2,00,000 ₹4,00,000 | 1,49,999 ₹2,99,998 |
| 2.00 | Supply, installing, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The fixing of double doors shall be on MS hinges with anti-theft provision (the door can’t be removed from enclosure without cutting enclosure). The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :-
INCOMING :-
(i) ACB 4 pole, 1000 Amps,50 Hz,415 Volts, 50 KA, with microprocessor release - 01 Nos
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 1000/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 2000A- set of four
OUTGOING :-
(i) MCCB 4 pole , 320 Amps, 50 Hz,415 Volts, 36 KA with thermal magnetic release - 02 Nos
(ii) MCCB 4 pole , 250 Amps, 50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos
(iii) MCCB 4 pole , 160 Amps, 50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos
(iv) MCCB 4 pole , 100 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 01 Nos
(v) MCCB 4 pole , 63 Amps,50 Hz,415 Volts, 16 KA with thermal magnetic release - 02 Nos
PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.
Note :-
(i) All out going feeder shall be connected by cable through suitable size gland plate / glands.
(ii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer | 1 | Each Job | 3,10,000 ₹3,10,000 | 4,00,000 ₹4,00,000 | 3,00,000 ₹3,00,000 | 4,00,000 ₹4,00,000 | 2,35,000 ₹2,35,000 Lowest | 5,00,000 ₹5,00,000 | 11,99,999 ₹11,99,999 |
| 3.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole, 320 Amps, 50 Hz, 415 Volts, 35 KA with microprocessor release - 01 No
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 600 A- set of four
(b) Outgoing :-
(i) MCCB 4 pole, 125 Amps, 50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos
(ii) MCCB FP, 63 Amps, 50 Hz, 415 Volts, 10 KA with thermal magnetic release - 04 Nos | 2 | Each Job | 1,85,000 ₹3,70,000 | 2,00,000 ₹4,00,000 | 1,12,000 ₹2,24,000 | 1,50,000 ₹3,00,000 | 1,90,000 ₹3,80,000 | 4,00,000 ₹8,00,000 | 99,999 ₹1,99,998 Lowest |
| 4.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 35 KA, with microprocessor release - 01 No
(ii) Onload changeover switch 400 Amps -01
(iii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iv) Ammeter digital type with 4 way rotary selector switch-01No
(v) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three
(vi) Indicating lamp- 01 set of three
(vii) Aluminium bus bar of rating 800 A- set of four
(b) Outgoing :-
(i) MCCB TP, 200 Amps, 50 Hz, 415 Volts, 25 KA with thermal magnetic release - 03 Nos
(ii) MCCB TP, 100 Amps, 50 Hz, 415 Volts, 25 KA with thermal magnetic release - 02 Nos | 2 | Each Job | 1,65,000 ₹3,30,000 | 2,00,000 ₹4,00,000 | 1,40,000 ₹2,80,000 | 1,50,000 ₹3,00,000 | 1,95,000 ₹3,90,000 | 1,35,000 ₹2,70,000 | 99,999 ₹1,99,998 Lowest |
| 5.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 36 KA, with microprocessor release - 01 Nos
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 630 Amps- set of four
(b) Outgoing :-
(i) MCCB TP, 250 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 01 Nos
(ii) MCCB TP, 125 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 04 Nos
(iii) MCCB TP, 100 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos | 2 | Each Job | 2,10,000 ₹4,20,000 | 2,00,000 ₹4,00,000 | 1,25,000 ₹2,50,000 | 2,00,000 ₹4,00,000 | 2,15,000 ₹4,30,000 | 1,15,000 ₹2,30,000 | 99,999 ₹1,99,998 Lowest |
| 6.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 400 Amps, 50 Hz, 415 Volts, 36 KA, with microprocessor release - 01 Nos
(ii) On load change over switch 4 Pole, 400 Amp - 01 No
(iii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iv) Ammeter digital type with 4 way rotary selector switch-01No
(v) CTs ratio 250/5 A ,class 1, ISI marked -01 sets of three
(vi) Indicating lamp- 01 set of three
(vii) Aluminium bus bar of rating 500 Amps- set of four
(b) Outgoing :-
(i) MCCB TP, 200 Amps, 50 Hz, 415 Volts, 25 KA with thermal magnetic release - 03 Nos
(ii) MCCB TP, 160 Amps,50 Hz, 415 Volts, 25 KA with thermal magnetic release - 01 Nos
(iii) MCCB TP, 100 Amps,50 Hz, 415 Volts, 25 KA with thermal magnetic release - 02 Nos | 1 | Each Job | 1,85,000 ₹1,85,000 | 2,00,000 ₹2,00,000 | 1,52,000 ₹1,52,000 | 1,50,000 ₹1,50,000 | 2,25,000 ₹2,25,000 | 1,65,000 ₹1,65,000 | 99,999 ₹99,999 Lowest |
| 7.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 320 Amps,50 Hz,415 Volts, 36 KA, with microprocessor release - 01 Nos
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 600 Amps- set of four
(b) Outgoing :-
(i) MCCB TP , 250 Amps,50 Hz,415 Volts, 36 KA with thermal magnetic release - 01 Nos
(ii) MCCB TP , 160 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos
(iii) MCCB TP , 63 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos | 1 | Each Job | 1,55,000 ₹1,55,000 | 2,00,000 ₹2,00,000 | 1,10,000 ₹1,10,000 | 1,50,000 ₹1,50,000 | 1,85,000 ₹1,85,000 | 1,09,000 ₹1,09,000 | 99,999 ₹99,999 Lowest |
| 8.00 | All as in item No 2 here-in-before but comprising of the following
(a) Incoming :-
(i) MCCB 4 pole , 630 Amps,50 Hz,415 Volts, 50 KA, with microprocessor release - 01 Nos
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iv) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 630/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 1200 Amps- set of four
(b) Outgoing
(i) MCCB 4 pole , 250 Amps,50 Hz,415 Volts, 36 KA with thermal magnetic release - 02 Nos
(ii) MCCB 4 pole , 200 Amps,50 Hz,415 Volts, 36 KA with thermal magnetic release - 02 Nos | 1 | Each Job | 80,000 ₹80,000 Lowest | 2,00,000 ₹2,00,000 | 1,40,000 ₹1,40,000 | 1,50,000 ₹1,50,000 | 2,75,000 ₹2,75,000 | 4,00,000 ₹4,00,000 | 99,999 ₹99,999 |
| 9.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 250 Amps,50 Hz,415 Volts, 35 KA, with microprocessor release - 01 Nos
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter 0-250 Amp digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 250/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 500 Amps- set of four
(b) Outgoing :-
(i) MCCB TP, 125 Amps, 50 Hz, 415 Volts, 25 KA with thermal magnetic release - 02 Nos
(ii) MCCB TP, 63 Amps, 50 Hz, 415 Volts, 25 KA with thermal magnetic release - 04 Nos | 2 | Each Job | 85,000 ₹1,70,000 Lowest | 2,00,000 ₹4,00,000 | 1,06,000 ₹2,12,000 | 1,50,000 ₹3,00,000 | 1,65,000 ₹3,30,000 | 1,05,000 ₹2,10,000 | 99,999 ₹1,99,998 |
| 10.00 | All as in item No 2 here-in-before but comprising of the following :-
(a) Incoming :-
(i) MCCB 4 pole , 250 Amps,50 Hz,415 Volts, 25 KA, with microprocessor release - 01 No
(ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No
(iii) Ammeter digital type with 4 way rotary selector switch-01No
(iv) CTs ratio 250/5 A ,class 1, ISI marked -01 sets of three
(v) Indicating lamp- 01 set of three
(vi) Aluminium bus bar of rating 500 A- set of four
(b) Outgoing :-
(i) MCCB 4 pole , 100 Amps, 50 Hz,415 Volts, 25 KA with thermal magnetic release - 02 Nos
(ii) MCCB 4 pole , 63 Amps,50 Hz,415 Volts, 16 KA with thermal magnetic release - 03 Nos | 2 | Each Job | 1,45,000 ₹2,90,000 | 2,00,000 ₹4,00,000 | 90,000 ₹1,80,000 Lowest | 1,50,000 ₹3,00,000 | 1,35,000 ₹2,70,000 | 92,000 ₹1,84,000 | 99,999 ₹1,99,998 |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
25 Jul 2025, 6:00 pmClosed
GE UTILITY ELECTRIC SUPPLY
GE UTILITY ELECTRIC SUPPLY DELHI CANTT-10
REPAIR AND MAINTENANCE LT PANEL, ACBS, MCCBS, EARTHING AND CONNECTED ITEMS AT DK PART- I, 105 TA, CARRIAPA VIHAR, ABDULLAH DAIRY, EME STN WORKSHOP, KANDHAR LINE, TAIC, INT FS, 202 CEDU, KANDHAR LINE OFFICERS ENCLAVE, 8711 FIELD CEREMONIAL BATTERY,
2025_MES_718461_1
GE ELECT/D-22/2025-26
Open Tender
Electrical and Maintenance Works
Item Rate
180 days
GE UTILITY ELECTRIC SUPPLY
AS PER TENDER DOCUMENT
7 documents required · 7 mandatory
₹500
Yes
GE UTILITY ELECTRIC SUPPLY
₹90,000
Yes
29 Dec 2025
4 Jul 2025
28 Jul 2025
4 Jul 2025
25 Jul 2025
18 Jul 2025
Amount
Supply, installation, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , mounted on angle iron legs 50x50x6mm thick, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system accomodated with 01 No ACB 4 pole, 800 Amp, 50 KA, 415 Volt AC Horizontal draw out type motorized, front operated with Micro processor based LCD protection release for adjustable over current, short circuit and earth fault protection fitted with aluminium bus bar link 1200 Amps for incomming and outgoing cable connection. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement . including excavation, earth work and platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed sotne aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.
Supply, installing, testing and commissioning in replacement of factory made and tested Bus bar chamber outdoor type with canopy made out of 3.15 mm CRCA MS sheet, and 40x40x5mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front opening type, with apron for cable entry closing locking arrangement ,of size 450mm x 450mm x 300mm with 4 Nos 500 Amps aluminium bus bar and with 250 Amp MCCB, 4 pole, 36 KA, 415 Volt 50 Hz including excavation, earth work and platform for the Bus bar chamber with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed sotne aggregate on top and grouting bolts etc for Bus bar chamber. The platform shall be such that it is of a height 45 cm above the nearest road level.
Material and labour for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6 mm thick, buried directly in ground (earth pit not less than 3.5 m below normal ground level) with top edge of earth plate not less than 2.5m below normal ground level, connected to galvanized iron strip 32X6 mm by means of electric arc welding of galvanised iron or steel as shown in electrical plate No 3 of SSR Part I, connected to earth test point and the equipment on the other side complete all as specified, including testing and commissioning complete all as specified and directed by Engr-in-Charge. Note : (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe 40mm bore GI pipe light grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth strip/GI earthing and protection pipe upto 7.5 meter beyond the earth plates electrode.
Supply and fixing in replacement of galvanised iron strip 32 X 6 mm for additional earthing lead beyond 7.5 meter complete all as specified and directed by Engr-in-Charge.
S&F in replacement KIOSK box wheather proof including made out of one piece mounted SMC base and door pole mounted hinged door size 333x233x120mm out side and 300x200x105mm inside dimensions comprising of aluminium bus bar 4 strips for 3 phase and neutral 63 Amps and 15 Amps fuse grip with base including embossing/painting of danger notice of size not less than 10cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body complete all as specified and directed by Engr-in-Charge.
S&F in renewal on load change over switch in sheet metal enclosure of capacity 800 Amps, 4 pole, 415 volt, 50 Hz fixed in any type of existing LT panel/Feeder piller including taking out old existing unserviceable changeover from panels etc complete all as specified and directed by Engr-in-Charge.
S&F on load change over switch in sheet metal enclosure of capacity 400 Amps , 4 pole , 415 volt , 50 Hz mounted on wall with fastner and suitable size of nut and bolts after taking down old existing un serviceable MCCB/SDFU etc complete all as specified and directed by Engr-in-Charge.
S&F on load change over switch with SS enclosure of capacity 200 Amps, 4 pole, 415 volt, 50 Hz mounted on wall with fastner and suitable size of nut and bolts after taking down old existing un serviceable MCCB/SDFU etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing in renewal of 3 pole power contactor ML-6 mounted on any type/description LT panel/feeder pillar/wall after taking down old existing un serviceable contactor etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing in renewal of 3 pole power contactor MNX-110 mounted on any type/description LT panel/feeder pillar/wall after taking down old existing un serviceable contactor complete all as specified and directed by Engr-in-Charge.
Supply and fixing in renewal of Analog Time switch , 240 Volt AC, 50 Hz, mounted on any type/description LT panel/feeder pillar/wall after taking down old existing un serviceable time switch complete all as specified and directed by Engr-in-Charge.
Supply and fixing in renewal of Astronomical Time switch, 240 Volt AC, 50 Hz, mounted on any type/description LT panel/feeder pillar/wall after taking down old existing un serviceable time switch complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement LT current transformer having ratio 400/5 Amp, 15 VA, Class 0.5 complete all as specified and directed by Engr-in-Charge
All as per Srl item No.24 herein before but CT ratio 250/5 Amp complete all as specified and directed by Engr-in-Charge.
All as per Srl item No.24 herein before but CT ratio 200/5 Amp complete all as specified and directed by Engr-in-Charge.
Supply and fixing of MCCB 200 Amp, 3 pole, 25 KA, 50 Hz with MCCB sheet metal enclosure mounted on wall with fastner and suitable size of nut and bolts after taking down old existing un serviceable MCCB/SDFU complete all as specified and directed by Engr-in-Charge.
Supply only in replacement of 11 KV electrical Rubber insulating seamless hand gloves complete all as specified and directed by Engr-in-Charge.
Supplying and fixing in replacement LED flood light fitting of following size complete all as specified and directed by Engr-in-charge :-
Supply & Fixing in replacement bracket for street light fitting complete with 2.2 mtr long 50mm dia GI pipe medium grade and including necessary mild steel clamp , nuts,bolts and wahsers and painting on steel surfaces with two coats of aluminium paint complete all as specified and directed by Engr-in-Charge.
S&F in replacement ACB 4 pole, 1000 Amps, 50 kA , 415 Volt AC Horizontal draw out type motorized (EDO), front operated with Microprocessor based LCD protection release for adjustable over current, short circuit and earth fault protection complete all as specified and directed by Engr-in-Charge.
Material and labour for disconnecting faulty /burnt end or portion of cable by removing the cable from loop including necessary excavation & earth work , suitable size of thimble LT tape , relaying and reconnecting the cable by removing faulty/burnt portion of cable and preparing fresh terminals for 25 Sqmm 3.5/4 core to 240 Sqmm 3.5 core of LT cable to LT Panel/pole/main switch complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of cable gland for LT panel/feeder pilar up to 50 Sqmm cable complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of cable gland for LT panel/feeder pilar for 70 sqmm cable to 240 Sqmm cable complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of cable gland for LT panel for 300 sqmm cable to 400 Sqmm cable complete all as specified and directed by Engr-in-Charge.
Material and labour in replacement of Voltmeter 0-500 V digital type as per existing size complete all as specified and directed by Engr-in-Charge.
Material and labour in replacement of Ammeter 0-400 Amp digital type per existing size complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of indicator lamp for RYB phases complete all as specified and directed by Engr-in-Charge.
M&L for cutting and removing grass, vegetation bushes etc from surrounding of installation/LT Panel/LT ACB panel and removing all rubbish to a distance not exceeding 50 m complete all as specified and directed by Engr-in-Charge.
Material and labour for painting of steel tubular poles (swaged type) 9 meter long (with or without swan neck) of street light with 2 coat of alluminium paint over a coat of red oxide primer complete also apply two coats of synthetic enamelled paints with yellow/white and black colours in strips above 1.5 mtr hight from ground/road level and writing letters and nunbers on poles upto 1.5 mtr hight from ground/road level complete all as specified and directed by Engr-in-Charge.
M&L for re-painting of LT Panels/feeder pillars of approx size 2 to 5 Sqm with 2 coats of super enamal paint over a coat of red-oxide with sparygun including writing of feeder pillar numbers in appropriate size of letters complete all as specified and directed by Engr-in-Charge.
M&L for re-painting of LT Panels/feeder pillars of approx size 5 to 10 Sqm with 2 coats of super enamal paint over a coat of red-oxide with sparygun including writing of feeder pillar numbers in appropriate size of letters complete all as specified and directed by Engr-in-Charge.
Supply and installation in replacement of old unsv RCC pole with steel tubular swan neck pole type 410 SP-31 (9 mtr long) complete with mild steel base plate, finial taper plug, bolts, nuts and screws including two coats of aluminium painting over a coat of primer for exposed surfaces and two coats of bituminous black paint over a coat of primer to the surfaces in contact with concrete inclusing two runs of PVC insulated 1100V multi-stranded copper wire of size 2.5 Sqmm from the junction box to the fitting complete all as specified and directed by Engr-in-Charge. Note :- The unit rate in this item is deemed to be included the cost oif exacavation and earth work in any type of soil,PCC foundation 1:4:8 type D-2 , PCC coping 1:2:4 type B-1 as in steel tubular pole . The steel pole shall be painted by bituminious paint total lenth inside and up to planting depth outside
Supply and installation in replacement of old unsv RCC pole with steel tubular pole type 410 SP-31 (9 mtr long) complete with mild steel base plate, finial taper plug, bolts, nuts and screws including two coats of aluminium painting over a coat of primer for exposed surfaces and two coats of bituminous black paint over a coat of primer to the surfaces in contact with concrete inclusing two runs of PVC insulated 1100V multi-stranded copper wire of size 2.5 Sqmm from the junction box to the fitting complete all as specified and directed by Engr-in-Charge. Note :- The unit rate in this item is deemed to be included the cost oif exacavation and earth work in any type of soil,PCC foundation 1:4:8 type D-2 , PCC coping 1:2:4 type B-1 as in steel tubular pole . The steel pole shall be painted by bituminious paint total lenth inside and up to planting depth outside
Supply only in replacement of old unserviceable Blower having volumetric flow rate 4 to 5 cum/min, 230 Volt, 50 Hz, complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of LED street light fittings capacity 60 Watt LED street light complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of LED street light fittings capacity 45 Watt LED street light complete all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement of outdoor type wall mounted bus bar chamber having 04 pole bus bar of rating 250 Amps fitted with MCCB 200 Amps 4 Pole, 25 KA, 50 HZ as incomer inclding suitable hole in bus bar for outgoing cable connection including suitable size nut bolt and fastener complete all as specified and directed by Engr-in-Charge.
S&F in replacement of UNSV /Burnt MCCBs of capacity 630 Amps, FP, 50 KA, 415 Volts 50 Hz, AC, with microprocessor release fixed in any type of existing LT panel/Feeder piller including taking out old existing unserviceable MCCB from panels etc complete all as specified and directed by Engr-in-Charge.
All as per sel item No 50 above but rating of MCCB 400 Amp, 35 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 50 above but rating of MCCB 250 Amp, 35 KA complete all as specified and directed by Engr-in-Charge.
S&F in replacement of UNSV /Burnt MCCBs of capacity 630 Amps, FP, 50 KA, 415 Volts 50 Hz, AC, with thermal and magnetic release fixed in any type of existing LT panel/Feeder piller including taking out old existing unserviceable MCCB from panels etc complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 320 Amp, FP, 36 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 250 Amp, FP, 36 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 200 Amp, FP, 36 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 160 Amp, FP, 25 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 100 Amp, FP, 25 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 53 above but rating of MCCB 63 Amp, FP, 16 KA complete all as specified and directed by Engr-in-Charge.
S&F in replacement of UNSV /Burnt MCCBs of capacity 200 Amps, TP, 25 KA, 415 Volts 50 Hz, AC, with thermal and magnetic release fixed in any type of existing LT panel/Feeder piller including taking out old existing unserviceable MCCB from panels etc complete all as specified and directed by Engr-in-Charge.
All as per sel item No 60 above, but capacity MCCB 125 Amp, 25 KA complete all as specified and directed by Engr-in-Charge.
All as per sel item No 60 above, but capacity MCCB 63 Amp, 16 KA complete all as specified and directed by Engr-in-Charge.
Note : Contractor should procure and provide 50 % of the material as listed above within 15 days of the placing of work order and shall be verified by the Engr-in-charge
DS CONSTRUCTION (BID ID -3370924)
MV Engineers And Contractors (BID ID -3364442)
Vijay Electricals (BID ID -3371199)
M/s JAIMAA ASSOCIATES (BID ID -3371097)
Rajindera Enterprises (BID ID -3371034)
mayur enterprises (BID ID -3364505)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .