SPECIAL REPAIR TO SINGLE SAILORS COMPLEX L BLOCK AT CHANAKYA BAGH CHANAKYAPURI

Amount

Demolition of brick work built in Cement mortar or cement lime mortar incl all quoins, arches , pillar etc complete all as specified and directed.

Demolition of reinforced cement concrete of any any description and in any position not otherwise speifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantlling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Taking down chowkhats or frame with shutters without taking of shutters from frames exc 1.5 Sqm but not exc 4.00 sqm each & removing form site incl making good disturbed portion complete all as specified and directed.

Taking down chowkhats or frame with shutters without taking of shutters from frames not exc 1.5 Sqm each & removing form site incl making good disturbed portion complete all as specified and directed.

Dismantling boarding, any description like cupboard/cabinets fixed in any position with nails complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks,less than half brick thick of straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed.

M&L for reinforced cement concrete type B-1(1:2:4) (using 20 mm graded granite stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Reinforced cement concrete (1:1.5:3) nominal mix, using 20mm crushed stone agg as in beams,roof beams, cantilevers,lintel over 1.5m span, bands, chajjas etc. complete all as specified and directed.

Use and waste of form work to sides of concrete foundations footings base of columns, plinth beams ,roof beams, raft and raft beams, sides ansd soffits of foundation complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished surfces of concrete complete all as specified and directed.

M&L of mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

All as per Sr Item No 14 here in before but 8mm dia as in stirrups

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise described complete all as specified and directed.

Supply and laying of AAC (Autoclaved Aerated Concrete) blocks of size 600x200x300mm with variations depending on the manufacturers, light weight having a dry density between 550-650kg/m3 and compressive strength between 3-4.5N/MM2 as per IS 2185 part3, as in sunken portion complete all as specified and directed.

M&L for cement concrete in filling mass for sunken concrete type B1, 1:2:4 (20mm graded stone crushed aggregate) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1,1:2:4 (12.5mm graded aggregate) as in sub bsae floor finishing the cement concrete complete all as specified and directed.

M&L for non skid matt finished ceramic tiles 10mm thick (Square/rectangular) polished, each tiles of size 600mmX600mm as in floors,skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in Cement Mortar 1:4 (Size and colour of tiles will be approved by GE) complete all as specified and directed.

M&L for joint free super gloss/high gloss glazed ceramic coloured tiles in vertical surface size 600mmx300mm, 8 to 10mm thick with matching highlighter over and incl 10 mm thick rendering 1:3 CM set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tiles (Size and design/colour of tiles will be approved by GE) complete all as specified and directed.

M&L for Non skid joint less coloured tiles 10mm thick area of each tile exceeding 0.36 sqm but not exceeding 0.74 sqm(1200X600mm) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr in charge.

M&L for machine cut Kota stone mirror finish of size 600x600mm in floor to be laid in geometric pattern with granite/marble inserted with precise factory high pressure waterjet cutting (area of granite/marble inlays n.exc. 20 %) flooring 20-25mm thick laid over and incl 20mm thick cement screed base with cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade includding rubbing and polishing complete all as specified and directed. NOTE:-The minimum cost of granite shall be Rs 150/sqft.

-Blank-

M&L for rounding the edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specifeid and directed.

Taking down cement plaster on brick wall surfaces including racking out joints hacking for key scrubbing down with water etc and removing the rubbish out of Mod Land complete all as specified and directed.

M&L 15mm thick rendering on fair or other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished complete all as specified and directed..

M&L 10 mm thick cement plaster in CM (1:3) on fair face of brick or concrete surfaces on ceiling finished even and smooth without using extra cement and using SBR latex emulsion @ 4% by weight of cement complete all as specified and directed. (SBR latex shall be measured and paid separately)

M&L 15mm thick rendering on fair or other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished complete all as specifeid and directed.

Supply only water proofing compound liquid(SBR latex) @ 200 ml per bag of cement complete all as specified and directed.

M&L for preparation of old plasterd wall surfaces complete removal of existing treatment of wall with machanically and applying wall putty(minimum 1.50mm thick) as per manufacturers instructions, surfaces to be finished even and smooth over a coat of alkali resisstane primer and applying two coats of exterior emulsion first quality Weather coat / Weather shield of approved colour and make complete all as specified and directed.

M&L for preparation of new plasterd wall surfaces and applying 1.5 mm thick wall putty as per manufactures instructions, surfaces to be finished even and smooth over a coat of alkali resisstane primer and applying two coats of exterior emulsion first quality Weather coat / Weather shield of approved colour and make complete all as specified and directed.

M&L Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper using roller brush, over a coat of primer and over incl one coat of 1.00mm thick putty complete all as specified and directed.

M&L for complete removal of existing treatment from old surfaces of ceiling scrapping by machanical means and applying two coats of oil bound distemper using roller brush, over a coat of primer and over incl one coat of 1.00mm thick putty complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying two coats of oil bound distember over 1.50mm thick putty over a coat of alkali resistant primer complete all as specifeid and directed.

M&L for preparation of old plastered wall surfaces complete removal of existing treatment of wall and applying two coats of oil emulsion distember over 1.00mm thick putty over a coat of alkali resistant primer complete all as specifeid and directed.

S&F for factory made single extruded WPC (wood polymer composite) solid door/window/Ceosetory windows and other frames/chowkat of size 125mmx65 mm comprising of virgin PVC polymer of K value 50-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame dencity of 750kg/cum, screw withdrawl strength of 200N (Face and 1100N edge), minimum compressive strength of 58N/Sqmm and resistance to flame of class A category and property of being termite/borer proof, water/moiture proof and fire retardant and fixed with MS hold fasts/lugs/SS Dash fastener of required dia and length of complete as per direction of Engr in charge. Note : For WPC solid door /windows frames, minus 5mm tolerance in dimension ie depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for factory made single extruded WPC (wood polymer composite) solid door/window/Ceosetory windows and other frames/chowkat of size 100mmx50 mm comprising of virgin PVC polymer of K value 50-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrawl strength of 200N (Face and 1100N edge), minimum compressive strength of 58N/Sqmm and resistance to flame of class A category and property of being termite/borer proof, water/moiture proof and fire retardant and fixed with MS hold fasts/lugs/SS Dash fastener of required dia and length of complete as per direction of Engr in charge. Note : For WPC solid door /windows frames, minus5mm tolerance in dimension ie depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mmx25mmx2mm and 32mm long steel screws drilled suitable to pass through Other hardwares should be fixed with 19mmx6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings." Note: fixture /fittings shall be measured and paid under relevant items.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed.

Supply and fixing WPC Cup Board made of 18 mm thick (solid PVC sheet) (Plus / minus 0.7) celuka PVC ply complete for hold of shelf / partition and shall provide 3 edges in sizes 18 mm x 18 mm as per required length. the edges of shelf / partition / wall side to be lipped with 18 mm x 1 mm thick PVC sheet of density 600 Kg /cbm manufactured by as ISO -9000 certified company , using solvent cement etc.( including all necessary Aluminium hardware fitting i.e Piano hinge , 4 handles, ball catchers including locking arrangement in each Cup board including dismantling of existing complete in all respect as specified and directed. Note (measurement should be taken external face only i.e. length and breadth)

S&F 200 mm long ISI cerified SS barrel tower bolts, with ss screws complete all as specified and directed.

S&F ISI certified SS sliding door bolts 250 mm long and fixed with ss screws to wooden doors complete all as speciifed and directed.

S&F ISI cerified SS butt hinges 125 mm long type C11 with ss screws fixed to wooden doors complete all as specified and directed

S&F ISI cerified SS handles 150 mm long polished bright with ss screws complete all as specified and directed.

S&F ISI cerified 140 mm stainless steel door stopper with twin rubber shoes fixed with SS screws complete all as specified and directed.

S&F in repair stainless steel drapery rod (curtain rod) of 25mm dia, wall thickness 1.00mm minimum, fancy type, complete all as specified and directed.

S&F stainless steel decorative type bracket and side cups for curtain rods 25mm dia fixed with screws complete all as specified and directed.

Supply and fixing in repairs floor mounted coupled star white one piece water closet (Pedestal pattern) premium class with P or S of size 220 mm, EWC, ensure more hygiene, slow falling seat cover, Elegant design, Easy clean, I trap including soft closed seat cover, hinges fixing accessories set and accessories set, including flushing cistern, with cistern fittings connection to drain or (outgoing pipe) & to flushing pipe anti siphonage pipe etc. complete in all respect as specified and directed. Make: Jaquar- CAT Part No CNS-WHT-855S300SPPSMY, Cera CAT Part No. S1013243 or Equivalent in Kohler.

S&F in repairs vitreous china wash hand basin counter/table top type of size 495mmX395mmx150mm in 18 mm thick granite (of any type) machine cut as in platforms, bedded and jointed with grey cement slurry and pointed with white cement with admixture of of pigment to match the shade of granite stone, including 32mm bore dia CP waste coupling, waste pipe and all reuired fittings complete in all respect as specified and directed. Make: Jaquar-CAT Part No JDS-WHT-25909, Cera CAT Part No S2020163 and Hindware CAT Part No- AVIOR R 91207.

Supply and fixed in repair 15mm bore dia Stainless steel finish quarter turn central hole basin mixer round spout with popup Waste assembly with 10mm dia , 450 mm long copper pipes complete in all respect as specified and directed by Engr-in-Charge. Make: Jaquar-CAT Part No COP-CHR-001BPM, Cera CAT Part No F1216452 and Hindware CAT Part No- F400014.

S&F angle valve (one way) 15 mm bore cast copper alloy fancy type, Chromium plated with cup complete all a specified and directed. Make: Jaquar- CAT Part No OPP-CHR-15053PM , Cera F2002201 and Hindware CAT Part No- F390005.

S&F chromium plated brass two way bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore complete all a specified and directed. Make: Jaquar- CAT Part No LYR-CHR-38041 , Cera F2002163 and Hindware CAT Part No-F520005.

S&F chromium plated brass nozzle bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore complete all a specified and directed Make: Jaquar- CAT Part No COP-CHR-049PM, Cera F-2002153 and Hindware CAT Part No- F730040.

S&F in repair CP Wall mixer (wall mounted model ) 3-1 system with provision for overhead shower complete with 115mm long pipe connecting legs and flanges. Over head shower 105mm dia round shape single flow (ABS body chrome plated with gray face plate) with rubbit cleaning system Code complete all as specified and as directed. Make: Jaquar- CAT Part No CQT-CHR-23273UPR, Cera F-2002401 and Hindware CAT Part No-F730022.

S&F in repairs, brass chromium plated shower rose 125mm size complete all as specified and directed. Make: Jaquar- CAT Part No SHA-CHR-457L200 & OHS-CHR 1687, Cera F-7010608AB and Hindware CAT Part No- F160120.

S&F brass chromium plated soap dish holder with CP brass screws complete all as specified and directed. Make: Jaquar- CAT Part No CPA-CHR-1131,Cera CAT part No- F5014116CH and Hindware CAT Part No- F840006.

S & F in repairs Soap dispenser with suitable bottle all as specified and directed. Make: Jaquar- CAT Part No AKP-CHR-35735P, Cera CAT part No F5014111CH or Equivelant in Hindware.

S&F in repairs, brass chromium plated tubular towel rails 20 mm dia 60 cm long with brass screws complete all as specified and directed. Make: Jaquar- CAT Part No ACN-CHR-1111SM, Cera CAT part No F5013103CH and Hindware CAT Part No- F870012.

S&F hand shower ( health faucet ) CP with 8 mm dia. 1.2 Metre long flexible tube and wall hook complete all a specified and directed. Make: Jaquar- CAT Part No ALD-CHR-577, Cera CAT part No F8030106AB and Hindware CAT Part No- F160110.

S&F (in repairs) ISI certified PVC connections 15mm size with CP nuts of length 600mm complete all as specified and directed.

M&L for PVC (SWR) floor trap /110 mm, setting and jointing with solvent cement complete all as specified and directed.

Dismantling of upto 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, pressure rating 6 kg/cm2 in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, pressure rating 6 kg/cm2 in any length with rubber ring joints laid in trenches complete all as specified and directed.

S&F PVC(SWR) 150 to 110 mm tee bore junction single (door Single T) equal or unequal with access door any radius complete all as specified and directed.

S&F PVC(SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC(SWR) 100 to 75 mm tee bore junction single (door Single T) equal or unequal with access door any radius complete all as specified and directed.

S&F PVC(SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC(SWR) 150mm bore Door bends/Tee/bent any radius complete all as specified and directed.

S&F PVC(SWR) 110mm bore vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) pipes 150mm bore single socketed, pressure rating 6 kg/cm2 in any length with rubber ring joints fixed to walls complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore dia of pipe including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing and connections of 20mm bore dia of pipe including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing and connections of 25mm bore dia of pipe including cleaning for refixing or removal to store complete all as specified and directed.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified and directed.

Supplying and laying of 25 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified and directed.

Supplying and laying of 32 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified and directed.

S & F 20 mm dia CPVC Brass Elbow complete all as specified and directed.

S & F CPVC Union 20 mm complete all as specified and directed.

S & F CPVC Union 32 mm complete all as specified and directed.

S & F 20 mm dia CPVC Brass Tee complete all as specified and directed.

S&F (in repairs) 25 mm bore gun metal, globe or gate valve with iron leaver head screwed both ends for iron pipe complete all as specified and directed.

S&F (in repairs) 32 mm bore gun metal, globe or gate valve with iron leaver head screwed both ends for iron pipe complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S & F 150 mm dia PVC (SWR) pipes 5 mm thick single socketed in any length with rubber ring joints fixed to walls as in rain water pipes complete all as specified and directed.

S & F 150 mm PVC (SWR) shoe any radius complete all as specified and directed.

Dismantling of PCC tiles/Brick tiles layed on roofs and removal from out of defence land site complete all as specified and directed

Demolition/Dismantling of Mud in roofs/PCC layer in any thickness/unserviceable RCC/Sunken concrete etc removed from out of defence land complete all as specified and directed

M&L for cleaning the surface, remove dust and loose particle and unsound substructure and providing 30 mm thick cement screed (1:4) mixed with Dr fixit STP or equivalent tonic liquid 200ml/Bag of cement over Dr Fixit bonding coat MPB applying primer coat with solvent based bitumen primer @ 0.35ltr/Sqm align Dr Fixit/STP torch shield or equivalent APP Waterproofing membrane 3 mm thick with one side rough finish weight not less 3.0 KG per SQM. using gas burner to heat substance, pressing firmly from lower end to upper end with 100 mm over lap excess compound smoothened pressed in to seam using hot trovel sea edges well into grooves and protuct with CM 1:2 complete all as specified and directed.

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement: 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner including 15 mmthick screed bed or bedding in CM 1:6 complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars;, staging, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for prepration of new steel surface of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Examining concrete by tapping with light hammer and marking of the loose concrete areas of structural elements in straight line geometrical forms, grooving the edges same with grinder upto 5 -10 mm depth without damaging existing rebars, carefully removing carbonated concrete around the rebars upto 10 mm depth by low impact high frequency hammer/ chipper without damaging the sound concrete, daily cleaning and stacking of debris at prescribed location in polypropylene/ paper bags, disposing off the debris so generated on weekly basis outside the premises, etc, complete all as specified and directed. (Note:- Rate to be inclusive of scaffolding, debris disposal as per site requirement and directed).

M&L for Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive SikaDur 31 or equivalent to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and directed.

M&L for Grouting & injecting grout in two parts, low viscosity, moisture insensitive injection-liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive injecting grout after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost.

M&L for cleaning existing reinforcement with wire brush/rotary wire brush to make surface free from rust scales, loose material, dirt etc complete and applying two coats of alkaline rust converting primer Sika RustOff 100 or equivalent as per Appx "E" on the existing rebar and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, with time interval of 1 hour between the coats complete all as specified and directed.

M&L for Providing and application of zinc rich epoxy anti-corrosive protective coating Sika Friazinc R or equivalent as per Appx "E" for rebar corrosion protection system in 2 coats of 0.4 kg/sqm complete all as specified and directed. The product should confirm carbonation resistance of 2 mm and bond strength > 1N/sqmm according to ASTM C 882-78.

M&L for Providing and application of corrosion inhibiting impregnation coating Sika Ferrogard 903 or equivalent as per Appx "E", designed for use as an impregnation for protection of steel reinforcement within unexposed concrete in consumption of 0.5 kg/Sqm complete all as specified and directed. The product should be amino alcohol and inorganic combination based migratory corrosion inhibitor for both cathodic and anodic protection.

M&L for Providing, mixing & applying two component epoxy resin concrete bonding coat Sikadur 32 LP or equivalent as per Appx "E" on prepared RCC surfaces as per manufacture specification including preparation of surface by chipping and thoroughly cleaning of surface complete wherever required in consumption of 0.4 kg/Sqm complete all as specified and directed. The product should comply with ASTM C 881 Type II Grade 2 Class B+C and bond strength should be 10 MPa.

Rebuilding the section of damaged RCC elements to its original size in thickness of 100mm by providing and casting with SikaRep Microcrete 4 or equivalent as per Appx "E" ready to use non shrink, cementitious free flow micro-concrete having compressive strength > 60 N/sqmm (28 days) according to ASTM C 1107-99 including providing and fixing of watertight foam faced finish shuttering of minimum 18mm thickness and supporting formwork or steel shutter for round columns, all lead lift, mixing, placing, de-shuttering, leveling the surface by grinding off cementitious slurry or cementitious joints differences if any and curing complete all as specified and directed.

Rebuilding the section of damaged RCC elements to its original size in thickness of 40mm by hand or spray application by Providing and applying Sika MonoTop®-412 (IN) or equivalent as per Appx "E" single component, fibre reinforced, sulphate resistant, low shrinkage, high performance cementitious structural repair mortar conforming to EN 1504-3 Class R4 on exposed concrete surface as per technical specification. Material should have Compressive strength ≥ 45 MPa as per EN:12190, Chloride ion content ≤ 0.05% as per EN:1015-17, Adhesive bond ≥ 2.0 MPa as per EN:1542, Carbonation resistance dk ≤ control concrete [MC(0,45)] as per EN:13295 & Elastic modulus ≥ 20.0 GPa as per EN:13412 complete all as specified and directed.. NOTE:(Complete finished item with all leads and lifts).

Providing, and applying single component, high build, elastomeric, crack-bridging, resistant to CO2 & SO2 and Chloride ion diffusion, UV resistant, breathable acrylic coating, with elongation at break exceeding 200% Sikagard - 550 W IN applied in two coats (each coat 100 micron DFT) on acrylic based primer at an average total thickness of 200 microns DFT in two coats including acrylic resin based primer Sikagard® 552 IN Primer W as per the recommendation of the manufacturers. Item rate inclusive of all materials, labours, supervision, tools, tackles, transportation, scaffolding/ temporary supports/working platform etc., complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness with cover fillets including MS frame work complete all as specified and directed..

S&F for GI frame work for decorative type seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspeneded from soffit at approx 900mm center to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm center to centre including providing and fixing Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish formulated jointing compound and 48mm wide fibre tape to provide seamless finish including preparation of newly surfaces of ceiling and applying two coats of oil bound distember over and including one coats of wall care putty complete all as specifeid and directed.

S&F powder coated aluminium anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.complete all as specified and directed.

S&F for Factory made jointless, rust free steel windows fabricated from roll formed sections made of galvanized steel colour coated S powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mmx0.58mm(c) Glazed guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittins (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle-04 Nos. Glass panes- Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass. WIRE MESH -Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate Distance between bars should not be more than 12 cms c/c. Total grill unit shall be enamel painted and fixed to window frame with screw. Including provision of cooler etc complete all as specified and directed.. Note: The glazed/Guaged shutter including guard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area shutter shall be the area of opening.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long - 01 Nos, hinges type B-21 100mm long - 02 Nos, suitable handle - 01 Nos etc in each shutter complete all as specified and directed.

Supply and fixing 5.0mm thick heat absorbing glass any size complete all as specified and directed.

S&F stainless steel wire cloth, 0.254mm nominal dia of wire and 0.95mm average width of aperture and fixed with tinned tacks or galvanised wire staple etc complete all as specified and as directed.

Supply and fixing 12mm thick WPC board for partition etc fixed with aluminium beading/cleats complete all as specified and directed.

S&F Powder coated aluminium ornamental grill 10 mm dia, 75 X 95 mm aperture fixed in powder coated aluminium snap beading complete all as specified and directed.

S&F for second class hard-wood in scantlings clean sawn in teak wood complete all as specified and directed.

M&L for complete removal of existing wooden surfaces with preparation of old / new surfaces and applying two coats of synthetic Varnishing of any description over a filler coat, over 10cm in width or girth in hand rails etc complete all as specified and directed.

M&L for cement conc type C2 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection complete all as specified and directed.

M&L for Green Marble work 16 to 18mm thick (table rubbed and polished) in steps, pillars, windowcills, cooking platforms and including cement mortar (1:4), 20mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed..

M&L for Green Marble work 16 to 18mm thick (table rubbed and polished) in riser of steps and including cement mortar (1:4), 10mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Description of Work / Item(s)

Amount

INTERNAL ELECTRIFICATION

Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fittings such as ceiling rose, pendent holders, regulators and socket point etc and making good the disturbed surface & wall/ floor complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLSH type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLSH type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit of minimum 25 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for the following :

One light/fan/exhaust point controlled by one no, one way 5 Amp switch.

One light point controlled by two way 6 Amp switch.

One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board

One three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board

All as per item No. 1 here in before but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board.Make:-RR Kabel/Polycab/Finolex

Note for item No 2 to 4:- (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in quoted rate.

S&F Modular switch 6A, single pole, 1 way switch, 1 module with IP 20 rating complete all as specified & directed. Make: Legrand CAT Part No.573400, Havells CAT Part No. AHFSXXW101, Schneider cat part No -X1101WH

S&F Modular switch single pole, 6Amp, 2 way switch, 1 module with IP 20 rating complete all as specified & directed. Make : Legrand CAT Part No.573402, Havells CAT Part No. ACASXXE102, Schneider cat part No- X1002WH

S&F Modular switch 1 way 16A, 1 module with IP 20 rating complete all as specified & directed. Make: Legrand CAT Part No. 573410, Havells CAT Part No.ACASXXE161, Schneider Cat Part No -X1101WH

S&F Modular socket 6A, 2/3 pin combined, 2 module, complete all as specified & directed. Make: Legrand CAT Part No. 573470, Havells CAT Part No.ACAKCXW163, Schneider Cat Part No -X2005WH

S&F Modular socket 16A, 2/3 pin combined, 2 module, complete all as specified & directed. Make: Legrand CAT Part No.573471, Havells CAT Part No. ACAKCXW163, Schneider Cat Part No -X2106WH

S&F in replacement of ceiling rose 3 terminal / PVC / Polycarbonate, insulated body all complete all as specified and directed.

Supply and fixing in replacement of Modular MCB SP 16Amps 240V 3 KA, C Curve, fitted in main switch board, including 2.5 sqmm wire connecting socket & modular MCB complete all as secified and directed by Engr-In-Charge. Make: Havells Cat No. DHFNCSPA016, legrand Cat part No 675974, Schneider Cat part No P8016-N.

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLSH type 1100V grade 2 x 6 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded FRLSH type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

S&F in replacement of factory made sheet steel distribution boards, double door, SPN 12 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing complete all as specified and directed. Make:- Havells Cat part No DHDESHCDOW12, Legrand Cat part No EKINOX 507612, Schneider Cat part No A9HSND12.

S&F in replacement of factory made sheet steel distribution boards, double door, SPN 8 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing complete all as specified and directed. Make:- Havells Cat part No DHDESHCDOWO8, Legrand Cat part No EKINOX 507611, Schneider Cat part No A9HSND08.

Supply and fixing in replacement of 240V, 10KA, B curve/ C Curve as per site requirement, MCB SP 6 to 32 Amps complete with connection complete all as secified and directed Make of MCB will be same as that of DB.

Supply and fixing in replacement of 240V 10KA, B curve/ C Curve as per site requirement, MCB SP 40 Amps complete with connection complete all as secified and directed Make of MCB will be same as that of DB.

Supply and fixing in replacement of MCB, 240V 10KA, B curve/ C Curve as per site requirement, MCB SPN 32 Amps complete with connection complete all as secified and directed Make of MCB will be same as that of DB.

Supply and fixing in replacement of RCCB double pole 32 Amps,sensitivity 30 mA, for earth leakage and shock protection complete all as specified and directed . Make of RCCB will be same as that of DB.

Supply and fixing in replacement of LED lights fitting 16-20W, 220V, (approx size 4 ft) PF> 0.95, min efficiency 120 lumen/watt, IP 20 rating, AC with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete all as specified. Make: Bajaj BCLAB 20W CW LED XT, CROMPTON : CCS-100-20-65-HL2-DP-NWH HE, Phillips Cat Part No BN308C LED20S-6500 L120 PSU WH.

S&F in replacement of aesthetically designed muziris decorative warm white LED picture light/mirror light of 8-10 watt, PF>0.95, min efficiency 100 lumen/watt, IP 20 rating CCT-3000K fixture with bronze finish for superior feel including suitable LED lamp of 10-12 W complete all as specified and directed. Make: Philips/Bajaj/Crompton

Supply and fixing in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V,PF>0.95, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make Havells-Cat No-VENUSNEO2X2PLR36WLED865PO /Philips Cat No:-RC370B LED36S-6500 G6 L60W60 PSU OD S6 /crompton- Cat No- LCTLRP-36-FO-CDL.

S&F in replacement of 1x4 fullglow recess mounted LED panel light of 36-40 W luminaire with high transmitive diffuser suitable for indoor space complete all as specified and as directed. Make Havells-PLUTONEO4X1PLR36WLED840S / Philips Cat No RC380B LED36S-6500 G5 L3W12 PSU OD / Crompton- Cat No-LCTLRNE-40-CDL(1X4).

“Supply and fixing in replacement of round shape 06-08 watt,PF>0.95 Warm White, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Makel:- Havells Cat No INTEGRAHEDLR7WLED857S / Philips Cat No DN590B M LED6S-6500 PSU WH WB /Crompton-Cat No:-CDR-211-06-30/40-SL-NWH

Supply and fixing in replacement of round shape 18-20 watt,PF>0.95 Warm White, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.. Make: Havells Cat No EDGEPRONEORDDLR18WLED840S /Philips Cat No DN296B LED20S-6500 PSU WH /Crompton- Cat No:- LSCRM-18W-CDL

Supply and fixing in replacement of aviation light luminaire, LED type comprising of aluminium housing with polycarbonate enclosure complete all as specified. Make: Bajaj/ Crompton/Philips.

S&F in replacement of 10 watt up down wall mounted lighter in aluminium housing with tempered cover IP -65 protection grade, water proof body,CCT-3000K,CRI>70 & 36 degree beam angle with PF>0.95 suitable for working from 160-270 Volt % 2 KV surge protection,declared life L70, 50 K burning hours complete all as specified and directed by Engr-In-Charge.(Make :- Philips/Wipro/Murphy)

Supply and fixing in repair of LED Bldg security light fitting 35 Watt 230 V PF>0.95 AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as secified and directed Make: Crompton/Philips/Havells.

Supply and fixing in replacment BLDC ceiling fan 1200 mm sweep, with remote 230 volts having full copper motor & ribbed alluminium blades for higher air delivery, powder coating provides longer life complete with accessories including making arragement to hanging of fan to ceiling with proper hook nut bolts complete all as specified & directed . make : Havells Cat Part No Enticer Prime, Orient Cat Par No Ecotech Prime, Bajaj Cat Part No Bajaj Ethora Plus. Note: A stand for fixing the remote will be provided by the contractor. The color of the fan will be approved by the competent authority and the quoted rates also include the cost of stand for fixing the remote of fan.

S& F in replacement of metallic body exhaust fan heavy duty of size 450 mm sweep AC single phase 230 V 50 HZ with copper wound motor,blades,frame,louvers and other connected accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size and making arrngement to fix the exhaust fan with proper nut bolt including taking down of existing old items complete all as secified and directed . Make:- Havells/Usha/crompton

Supply & fixing of wall fan complete with blades, Frame and all connected accessories operating at 230 V with 400 mm sweep, color as per site requirement.Making arrangement for hanging fans to wall with proper hook,nut,bolt with twin core twisted flexible copper conductor including taking down of existing old items complete all as specified and directed . Make:- Havells Cat Part No FHWSUSTGRY16, Orient model No Wall 49, crompton model No Neo 400.

Supply and fix in replacement of hot water storage electric water heater, steel body with SUITABLE INNER TANK AS PER OEM RECOMMENDATION and heating element upto 2.0 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such asassembly, safety valve, thermostate, NRV, connection piece etc including taking down of existing old items. Make:- BAJAJ SHIELD SERIES CREST PLUS, Usha Cylandra, Crompton REGERA.

S&F in replacement of factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way VTPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete all as specified. Make : Legrand Cat part No 507725, Havells Cat part No DHDMTVODCW04, Schneider A9HVM04.

S&F in replacement of MCCB 4 pole 63 Amp, 415 Volts,16kA adjustable type including thimbles, nuts, bolts ,washers etc. and connections all as specified and directed. Make is same as that of DB.

Supply & Laying in replacement of XLPE LT cable 1100 volts grade heavy duty with XLPE insulated stranded aluminium conductor of size 16 sqmm 4 core, served with an inner sheathing of PVC Tape armoured with galvanized steel strip or wire and over all PVC Sheathed stranded conductor conforming to IS-7098 (Part-I) with latest amendments laid in tranches/fixed to wall/pole/laid in floor including necessary connections and suitable size of thimbling complete all as specified and as directed

Supply, installation, testing and Commissioning of Industrial Ductable Super Cooler Made of 100% Virgin UV stabilized Industrial grade polymer cabinet, Rust and shock free for life, 10 year warranty on outer shell/ body cabinet, 4G Rigid Media cooling Pads for long life and great cooling efficiency of upto 85% , heavy duty three phase single speed fan motor made of 100% Copper wiring which produces 25000 CMH, Turbo Axial Fan for Super Low Sound and super long air flow upto 100 feet, including high quality MCB remot Control Power Panel and this machine can run on Generator complete including PVC drain pipe of size 30mm with all fittings and connection with water and electricity all as specified and directed by Engr-in-Charge. Make:- KAAVA-4G-toofan 25 K or equivalent model of Havells/USHA/SYMPHONY Note:-1 Contractor must submit OEM recommended layout diagram of ducting for the approval of competent authority prior to starting the work. Note:-2 Installation, commissioning and maintenance for the liability period should be done by Original Manufacturers of the machine/ equipment. Note:- 3 The Quoted rate also include the cost of fire retardant anti vibration canvass connector for connection of cooler with duct. Note:4 The Quoted rate also include the cost of Industrial wall mounted plug socket three phase 16 Amp rating 3P+N+E suitable for IP 67 degree of protection all as specified and directed by engineer in charge.Make- L&T/C&S/ABB/HAVELLS Note:5 The Quoted rate also include the cost of gun-metal, globe or gate or stop valves, with iron wheel head, screwed both ends for iron pipe and fixed or 15 mm dia complete all as specified and directed by engineer in charge Note: 6 The Quoted rate also include the cost of Ball valves high pressure of PTMT with epoxy coated Aluminium Rod & high density plastic ball screwed for iron pipe of size 25 mm dia bore and fixed complete all as specified and directed by Engr-in-Charge Note: 7 The Quoted rate also include the cost of PVC connection pipe of 15 mm bore of length 600 mm longcomplete all as specified and directed by engineer in charge

EXTERNAL WATER SUPPLY

Trenchless excavation for taking out old existing pipeline of 100mm/50mm size pipe and for new pipeline which is to be laid complete all directed and specified Note : (i) Cost of make good cost is deemed to be included in this rate. Nothing extra shall be paid on this account. (b) Cost of returning & refilling and removal of extra soil deemed to be included in this rate and nothing extra to be paid on this account.

Taking out from trenches / from under roads existing old unservicable rusted / corroded GI pipe 100 mm bore and connections including all fittings complete all as specified and directed.

Supplying, Laying, jointing and testing of GI steel water tubing 100 mm bore ISI marked medium grade galvanised including tube fittings Viz Tees, Socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road complete all as specified and directed.

All as per serial item No. 40 here in before but for GI pipe of 50 mm bore. Note for serial item No. 40 & 41:- (i) Excavation and Earth work shall be measured and paid separately under respective item of Sch of work. (ii) The cost of GI fittings are included in the quoted rate of this item and nothing extra shall be paid on this account..

EXTERNAL ELECTRIC SUPPLY

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240.0 sq mm 3.5 core and taking down of old U/S aluminium cable any type/size complete all as specified and directed. Note : (a) Trenchless excavation to be done being a cable passing through hard standing/under road/ near building or other areas. the cost of excavation is deemed to be includded in this rate. Nothing extra shall be paind on this account. (b) taking down existing old cable shall be deemed to be included in this rate. Nothing extra shall be paid on this account.

Supplying, laying, jointing and testing of GI steel water tubing 80 mm bore ISI marked light grade galvanised including tube fittings Viz Tees, Socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road as a cable cover complete all as specified and directed.

AIR CONDITIONING

Supply and installation of split Air Conditioner unit indoor/outdoor complete set with compresoor, motor, fan, cordless remote control unit, inbuilt stabilizer and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and of capacity 1.5TR complete all as specified and directed.

LIGHTING PROTECTION SYSTEM

Supply & fix single pointed air termination aluminium rod 12mm dia, 300 mm long complete all as specified and directed.

Supply & fix aluminium strip 25mm x 3.15 mm complete with saddles and fixing screws for fitting the strip on top of parapit wall/water tank/machine room/Mumty roof and on wall as down conductors complete all as specified and directed.

Supply and fix GI strip 32mm x 6mm buried in ground for connecting all earthings complete all as specified and directed.

S&F Test point terminal block made of Gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

Supply and fixing of 40 mm dia GI pipe light grade with all fittings complete all as specified and directed

Material and Labour for pcc block 1:2:4 type B using 20mm graded stone) base.for air termination rod complete all as specified and directed

M & L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanised strip of size 32 mm x 6 mm as earth lead, by means of bolts, buts, check nuts and washers of galvanised iron or steel, galvanized iron pipe light grade of 40 mm diameter, connected to earthing test point, all as shown in electrical plate No. 3 of SSR part I, connected to earthing test point all as specified or indicated including testing on completion and including excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep, with a 10 mm thick CI cover, hinged to CI frame on ground level, GI watering pipe 20mm medium grade, funnel, etc. complete all as specified and directed.

M&L for Supply, Fabrication, Installation, Balancing and Commissioning of Site fabricated GSS sheet metal rectangular ducting with supports as per IS 655-2010 complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports & mounting ,connecting unit to duct ,controller fixation ,joint gasket , nut bolts ,flanges ,cleats etc. of 24 gauges complete all as specified and directed .

Supply & Fixing of double louvered Air grills with auto swing & rust free for life, specially engineered grill for upto 2X longer airflow & wider angle coverage and upto 50% less sound icluding nuts, bolts, screws ,rubber gasket etc. to make the system complete all as specified and directed .

Supply, installation, testing commissioning of flexible LED strip light in 800 lumens/mtr and 105 lumen/Watt suitable for cove lighting. Strip Wattage must not exceed 7.6 Watt/mtr, Color consistency ≤ 3 with life time @ L70-30,000 Hours, CRI > 80; R9≥ 0 and CCT 2700K with IP20 and IK03 rating complete all as specified and directed.. Make: : Signify ( Philips) / iGuzzini/ Linealite/ martin & We-ef

Supply and fixing and replacement of occupancy sensor based LED lights fittings 16-20Watt, 200 Volt ,approx size 4 ft Power factor ≥ 0.90 with min efficiency 100 lumen/Watt , IP20 rating with constant current output driver connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: Phillips/Crompton/Havells

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLSH type 1100V grade 2x4 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x4 sqmm PVC insulated unsheathed copper conductor multi stranded FRLSH type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

SAGGI ELECTRIC COMPANY (BID ID -3337925)

India Guniting Corporation (BID ID -3338084)

JYOTI ENTERPRISES (BID ID -3334576)

M/s Innovative Coolings and Constructions (BID ID -3345570)

imran construction company (BID ID -3337966)

Third Wave Services Pvt Ltd (BID ID -3337671)

ASSOCIATED CONSTRUCTION CO. (BID ID -3337992)

SAGGI ELECTRIC COMPANY (BID ID -3337925)

JYOTI ENTERPRISES (BID ID -3334576)

GOYALA INFRA PROJECTS PVT LTD. (BID ID -3337444)

India Guniting Corporation (BID ID -3338084)

Third Wave Services Pvt Ltd (BID ID -3337671)

imran construction company (BID ID -3337966)

M/s Innovative Coolings and Constructions (BID ID -3345570)