SPECIAL REPAIRS TO BLDG No. BC 77 OFFICERS MESS OF THE MLIRC AND SPECIAL REPAIRS TO BLDG No. P 1 UNDER GE I BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of plain cement concrete of any description and in any position, not otherwise specifically provided for all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding precast concrete articles, in any position below or above ground level all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tile in roofing all as specified and directed.

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Demolition of stone slab and tiles of any description and any thickness in floors laid, bedded and pointed in any mortar all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Hacking out old broken glass (any thickness/ size, quality or description) from wooden frames, glazed with putty or fixed with beads all as specified and directed.

Taking up or down existing unserviceable 15mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Taking up or down existing unserviceable 20mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L for plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in surface channels, drains and similar works all as specified and directed.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

Removing building materials etc. (other than spoil) to a distance of 1 to 2 km, beyond the lead included in the rates, including loading, unloading and stacking at the destination all as specified and as directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

Fixing only serviceable timber fillets, square, rectangular or triangular in section, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

M&L for aluminium frame work as in doors, partitions and windows using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc including dismantling of existing aluminium joineries and making good disturbed surfaces all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F plain galvanised mild steel sheeting with grade of zinc coating 275, 0.8mm thick, in ridges, hips, valley gutter, drip and straight flashings including dismantling of existing unserviceable PGI sheets of any description and size and making good disturbed roof members all as specified and directed.

M&L for designer concrete roofing tiles, rustic red colour, 420 x 330mm size, 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry all as specified and as directed. Make: ETERNA model of INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete ridge/ hip cap tiles to suit designer rustic red concrete roofing tiles, 330 x 207/249mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete hip starter tiles to suit designer rustic red concrete roofing tiles, 360 x 210mm size, minimum 17mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete 3 way cap tiles to suit designer rustic red concrete roofing tiles, 351 x 429mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

M&L for 4mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41), weight not less than 7.6 kg per sqm, complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc including provision three coats of white wash on ceiling all as specified and directed.

S&F suspended false ceiling system with 16mm thick mineral fibre acoustical MINA TUFF EDGE TILES (MIRO LOCK), performance class - I (BS 456, Part 6&7) with bio coating on the exposed face of tiles, module size 60mm x 00mm, laid on 15mm thick SILHOUTTE EXPOSED GRID system, with medium load carrying capacity of 11.68 kg/ sqm, white/ black colour, all as specified and as directed.

Roughening old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3 kg of cement per Sqm to receive screed bed all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 9 to 10mm thick, cut to size required on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450mm x 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in floors, platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C1, (Using 20 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane all as specified and directed.

M&L for 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane all as specified and directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of plastic emulsion paint over a coat of alkali resistant primer on surfaces of walls over 1mm tick wall care putty including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for two coats of varnishing over oil staining over a filler coat of liquid transparent including necessary preparation of surface of wood and wood based materials, new or old, of any description and girth, not otherwise described all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S & F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F 15mm bore stop valves, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repqairs 15mm bore pillar taps, brass chromium plated, with capstan heads, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F counter type vitreous china wash basin, white, size 580x450mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands, etc. comlete all as specified and directed.

S&F in repairs 110 mm bore UPVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

Taking down carefully existing point wiring of light/ fan/ bell/ 5 Amps socket/ 15 Amps socket/ 2 way light point, etc. complete of any description including fittings and fixtures such as switches, sockets, call bells, ceiling roses, pendants, holders, regulators, call bells, light fittings, etc. and making good the disturbed surfaces of walls, floors, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module GI terminal box flush mounted into wall with standard white modular cover plate & frames for mounting switches/ sockets etc. for one light point controlled by one modular switch 1 way complete all as specified and directed.

All as described in item No. 75 but for one ceiling fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 75 but for one cal bell point controlled by one bell push.

All as described in item No. 75 but for one 05 Amps socket outlet on independent board.

All as described in item No. 75 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 75 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 4 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Four runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular bell push, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F modular fan regulator, step type, 2 module, 120 Watts, 230 volts, AC, all as specified and directed.

S&F PVC ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F in repairs call bell, ding dong, 230 volts AC supply all as specified and directed.

S&F in repairs, MCCB DB VTPN 8 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCCB FP 125 Amps ,16KA, 415 Volts, AC supply, fixed thermal magnetic settings, fixed in sheet metal enclosure complete all as specified and as directed.

S&F MCB TPN 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB DP 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED PANEL light fitting, recess mounted, 12W, 230V, with opal diffuser integrated electronic driver and all accessories internally pre wired complete including provision of 12W high brightness LEDs and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS OCTANE PANEL or equivalent in Crompton Greaves/ Philips/ Wipro

S&F 2 Watts LED luminaire wall mounted, grey/ metal synthetic with all accessories internally pre wired 2W LED 2700K including provision of suitable size VC board/ wooden board with sunmica top for fixing of light fitting and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: Cat No. 30975 of PHILIPS or equivalent in Crompton Greaves/ Havells/ Wipro.

S&F energy saving surface mounted, decorative hexagonal bulk head edge-lit LED luminaire 10W, comprising of high brightness LEDs. comprising of high brightness LEDs complete with all accessories internally pre wired complete including provision of 10 Watts high brightness LEDs 6000K, suitable size wooden board with sunmica top and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block complete all as specified and directed. Make: Havells HEXA - IP66 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F 25 Watts energy saving LED post-top lantern, IP 65 class of protection, symmetrical light distribution with spun aluminium body and high power LEDs 5700K complete with electronic driver and all accessories fixed in position including provision of 1.5sqmm PVC insulated multistranded copper conductor cable from junction box to light fitting and connecting up and testing all as specified and as directed. Make: Havells 'RUBY (CLEAR)' model or equivalent model in Philips/ Crompton Greaves/ HPL

S&F in repairs ceiling fan, 230 volts, single phase, 1200mm sweep, 5 Star rating with all accessories complete all as specified and as directed. Make: HAVELLS Model No. ES-50 Premium 5 STAR rating or equivalent model in makes CG/ ORIENT

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

S&F in repairs exhaust fan, 250mm sweep, 1200 RPM, 230 Volts, single phase, PVC body with gravity shutter and fixing arrangements including fixed into plywood base of suitable size with suitable bolts and nuts and fixing the plywood to existing window and provision of suitable size flexible copper conductor cable from connector to ceiling rose all as specified as directed. Make: Ventil Air-DX model of HAVELLS or equivalent model in USHA/ KHAITAN/ CROMPTON GREAVES

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Returning filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for approved riddled earth, spread dry in trenches as in cable cushioning at bottom and top including punning down all as specified and as directed. Note :- Punned thickness will be considered for payment.

M&L for burnt bricks, old size, sub class 'B' of designation 75, laid in trenches as in protection for UG cables all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 50 Sqmm x 3.5 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete all as specified and as directed. Note: Excavation, earth work, sand cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

RAHUL SAYAJIRAO DESAI

M/s. N D KALING

SAGAR ENTERPRISES

M/s. KIRAN M CHOUGULE

SHRI.H.R.PATIL

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS