PROVN OF 01 X STORE ROOM, INSTRUMENT SHOP AND ELECTRO MEDICAL EQPT SHOPS AND SMALL ARMS, DEFICIENT EXPLOSIVE STORE AND RETAINING WALL CUM RCC DRAIN UNDER GE JHANSI

Amount

Surface dressing n exc15 cm deep in Hard / dense Soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M&L for Surface excavation n.exc 30 cm deep and and avg 25 cm deep and getting out soft and loose soil all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation ,shafts wells etc n exc 10 sqm on plan and getting out in hard/ dense Soil complete all as specified and directed.

Excavating over area n.exc 1.5mtr deep and getting out in hard dense soil complete all as specified and directed.

Excavating over area exc 1.5mtr and n.exc 3mtr deep and getting out in hard dense soil complete all as specified and directed.

M&L for Moorum/ red bajri filling under floor and spreading in layers n exc15 cm thick incl well ramming and watering as required complete all as specified and directed.

M&L for hardcore (broken stone/boulders) of gauge exc 63mm but n exc. 100 mm deposited,, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

Returning, filling in, including spreading, levelling, wateringand well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for brickwork with sub class ‘B’ bricks (old size), straight or curved on plan exc 6m mean radius, built in Cement Mortar 1:6 completed all as specified and directed as in steps etc.

M&L for brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for pre-construction ATT for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for pre-construction ATT for treating the the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for pre-construction ATT for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for pre-construction ATT for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for PCC(1:4:8) type D-2 (using 40 mm graded stone aggregates) as in concrete in foundations, filling and mass concrete complete all as specified and directed.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast Foundations Elements for sizes as desired in structural drawing within 1 mtr width to length within 3 mtr long for 150 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including jointing lips and hooks, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast Foundations Elements for sizes as desired in structural drawing within 1 mtr width to length within 3 mtr long for 200 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including jointing lips and hooks, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast RETAINING WALL and both side fair finish Elements for sizes as desired in structural drawing width upto 2.0m to height within 5.0 mtr for 150 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast WALL Elements for sizes as desired in structural drawing width upto 3.5 m to height within 5.0 mtr for 125 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing cut outs for doors, windows, vents, sewerage pipes, etc lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast WALL Elements for sizes as desired in structural drawing width upto 3.5 m to height within 5.0 mtr for 75 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing cut outs for doors, windows, vents, sewerage pipes, etc lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast Roof SLAB Elements for sizes as desired in structural drawing width upto 3.0 m to span within 4.0 mtr for 125 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing flexible conduit for connection of wall and slab conduit, filling concrete in the holes kept for jointing electrical and plumbing pipes, providing required cutouts for sewerage pipes, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast Foor SLAB Elements for sizes as desired in structural drawing width upto 3.0 m to span within 3.0 mtr for 100 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing flexible conduit for connection of wall and slab conduit, filling concrete in the holes kept for jointing electrical and plumbing pipes, providing required cutouts for sewerage pipes, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast BEAM Elements for sizes as desired in structural drawing width upto 0.45m by depth upto 0.75m to span within 6.5 mtr, including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing flexible conduit for connection of wall and slab conduit, filling concrete in the holes kept for jointing electrical and plumbing pipes, providing required cutouts for sewerage pipes, lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast WALL, CHAJJA OR SHELF Elements for sizes as desired in structural drawing width upto 1.2 m to height within 2.1 mtr for 65 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing cut outs for doors, windows, vents, sewerage pipes, etc lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

Providing ,transportation , Fixing ,erection and installations etc complete for RCC Precast WALL, CHAJJA, SHELF Elements for sizes as desired in structural drawing width upto 1.2 m to height within 2.1 mtr for 50 mm thick , including mould making, providing and fixing reinforcement steel, casting with required admixtures, demolding, curing, transportation, storage, and finally erection at site. This also Includes all labour wages for each stage, machinery, cranes to lift at place at various stages etc including placement of electrical conduits and switch boxes as per drawing, placement of CPVC pipes 20 mm or 25 mm as per requirement including FTA and MTAs, including jointing lips and hooks, grout couplers if required, GI pipes for dowel bars, providing dowel bars as per design, grouting the joints wherever required, or welding already provided jointing steel bars, making good the joint with Laticrete or equivalent, providing cut outs for doors, windows, vents, sewerage pipes, etc lifting and fixing arrangements, including vetting of structural drawings of each precast elements from IIT /NIT etc complete all as specified and directed. Note : Thickness of precast element shall be provided as per the vetted structural design/ drawings received from IIT/ NIT without any extra cost to the department for additional thickness if required.

M&L 50 mm thick cement concrete type B1 (using 20 mm graded stone aggregate) as in) as in flooring finished even and smooth w/o using extra cement with providing 38mm wide glass dividing strips of 3mm thick insert in position n.exc 2 Sqm complete all as specified and directed. Note:- 3mmthickGlass dividing srip shall be measured under seperate item

Material supplied only of 38mm wide and 3mm thick glass dividing strip complete all as specified and directed.

M&L for ESD flooring mat thickness 2mm in rolls of 2.00 mtr X 15 mtr in length, three layered,colour blue,including glue,welding rod,copper strip, contact button and grounding card single side complete all as specified and directed.

21.M&L Granite (of any type) slab 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25 mm thick and laid over and incl 20 mm thick screed bed in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting / Griding / mirror Polishing on Kota stone complete all as specified and directed.

M&L Kota stone slab 15-18mm thick in riser of steps, skirting, dado and pillar laid over and incl 10mm thick backing coat in (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection finished the surface even and smooth without using extra cement and laid and laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand ) surface, complete all as specifed and as directed . Note The quoted rates are deemed to be inclusive of material against form work and joint fillings.

M&L for Non skid ceramic colored tiles of size 300x300mm, 7 to 8 mm thick (square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for glazed ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.

S&F of 35mm thick factory made modular designer flush doors, solid core construction, with block board core and prelamination on both sides, complete all as specified and directed.

M&L for second class hard wood. Plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

S&F for 1.25 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

M&L for box type steel window with 80x40x1.25 m MS tubular frame with side hung shutters ( double shutter for glass and gauze) without sash bars jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doweled and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Side hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

M&L for box type steel ventilator with 80x40x1.25mm MS tubular frame partly gauged with top hung shutter with and incl grill using 12mm square bars @ 10Cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars dovetailed and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Top hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

S&F 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cabinet (all arround ), shelves/shutter or similar work, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish or electro galvanized width of flaps (when open) 30mm, complete all as specified and directed.

S&F Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs hinges, lock strike plate, etc., complete as specified, supplied and fixed complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter (double leaf) of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F in repair 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed including hacking out old glass complete all as specified and directed.

S & F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S&F of 100mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed with screws, complete all as specified and directed.

S&F of 300mm long mild steel, sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, complete all as specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of 75mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 75mm aluminum handle cast type anodized complete all specified and directed.

M&L for preparation of new plastered surface and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed

M&L for preparation of new plastered surface and applying three coats of white wash on new plastered ceiling surface, complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar as (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface when concrete is green, complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral liquid water proofing compound, mixed in cement morter as per manufacturer instruction, complete all as specified and directed.

M&L for clearing the non accessible roof top surface of concrete and providing water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100 micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3 kg/sqm with 100mm overlap laid as per manufacturers instructions, complete all as specified and directed with following courses of description below :- (a) Applying evenly a coat of bituminous primer confirming to IS-3384-1965 @ 0.40 kg/sqm on prepared surfaces till the surface is properly impregnated. (b) Second coat of bonding material using blown grade bitumen 85/25 conforming to IS-702 @ 1.20 kg/sqm (c) third course is laying APP based modified membrane described hereinbefore with 100mm overlap in longitudinal direction and 100mm in tranverse direction, all joints and changes in all directions should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (d) Fourth coat of bonding materials using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 kg/sqm (e) Apply a coat of bituminous aluminium paint @ 0.20 kg/sqm.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick Wooden texture moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

S&F of Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood coloured PVC sheet and edges, reinforced with MS square tube, as specified in SSR Part-II 2010 (Section 8, on Page no - 175), complete all as specified and directed.

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

M&L for PCC type B0 (using 12.50 mm graded stone graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string course, coping apex tone, bed plate, kerbs and the like including weathering, slightly rounded or chamfered angles with throating, kerb stop rounded or chamfered in edges complete all as specified and directed.

M&L for 60 mm thickness, machine pressed precast M35 grade concrete interlocking paver block (cobble stone) any shape and size confirming to IS 15658 -2006 with grey cement and , pigment complete all as specified and directed.

M&L for sand cushion over sub base ,complete all as specified and directed.

M&L 100 mm Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) for pavement of pathway complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in floors and walls complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple incl float valve and gate valve, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection,, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC floor trap/ nahani trap of of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

S&F of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

S&F of 1st quality vitreous China white urinal flat back (Large size) with and incl CP waste coupling of suitable size, cast copper alloy CP spreader union with discharge pipe duly connected to auto closing angle cock, complete with necessary fittings, complete all as specified and directed.

S&F of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as specified and directed.

S&F of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all as specified and directed.

S&F for of PVC connection 450mm long x 15mm dia PTMT (PVC), complete all as specified and directed.

S&F of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F of tubular towel rail 20mm dia, D type, 600 mm long and wall bracket made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

S&F 15 mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

M&L for Walling of random rubble,uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in 1:4 cm rendering is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for PCC (1:2:4) type C1 using 12.50 mm graded stone aggregate as in band, string course coping apex stone bed plate kurbs abd the like incl weathering , slightly rounded or chamfered angles with incl necessary use and waste of form work complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in drain and surface channel complete all as specified and directed.

M&L for forming fair finished surfaces of drain or channels 30 cm inner girth in cement concrete using extra including forms, moulds mitred/ stopped ends etc., complete all as specified and directed.

M&Lfor preparation of new plastered surface of walls and applying two coats of cement base paints complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.

Providing and fixing SFRC (Steel fibre Reinforced Concrete) cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter confirming to IS-12592, total weight of cover and frame not less than 182 Kg fixed in cement concrete 1:2:4 type B-1 using 20mm garded stone aggregate complete all as specified and directed.

M&L DWCPE(SN8) 200 (OD)/175(ID)mm complete laid in trenches including earthwork, removal and return filling and jointed including testing alongwith necessary jointing material tees/ union / socket etc complete laid on PCC beed 150 mm thick PCC in 1:2:4 type B0 of avg depth 2.0 m including packing under and haunching against the side of pipes after they are laid and tested all as specified in IS 16098:2013 and as directed.

M&L for construction of Septic tank including excavation in any type of soil, foundation in PCC 1:2:4 type B2, brick work in CM 1:4, RCC M25 (with and including reinforcement), Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame, Vent pipe shaft and sludge chambers etc, complete for 25 users, all as specified and shown in drawing No CEBZ/TD/76/2011 Sheet 1/2 & 2/2 complete all as specified and directed. Note : 1. The Reinforcement shall be used 10 mm dia 150 mm c/c in main bar and distribution bars. 2. The cost of all kind of earth work, brick masonry work, plastering, coping, RCC slab, reinforcement, form work etc is deemed to be included in quoted rate only.

Construction of Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes ofsize 1.80 M dia X 3.00 M deep complete all as specified and directed.

Excavating in post holes or similar holes, each not exceeding 0.5 Cum, getting out in Hard/ dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and directed.

M & L for angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E complete all as specified and directed.

Supply and fixing chain link fencing of MS GI wire mesh of size 50x 50 mm of 3 mm dia of GI wire including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed.

M&L for preparation of new steel surfaces of any desc n. exc 10cm width or girth when unconnected with other painting or when painting in diff tint and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers with neck dia 11 to 15 mm and length exc 15 cm but n exc 22.5 cm long and one hexagonal or square nuts complete all as specified and directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, quality confirming to GDE Fe410-S complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of electrogalvanised GI terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated ISI sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points:-

One light point controlled by one switch

One Exhaust fan point controlled by one switch.

One ceiling fan controlled by one swith

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Srl item No 117 above but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 1.5 sqmm + 1 run x 1.5 sqmm with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length.

Notes for item No 117 to 120 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.

S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

Supply and fix electronic fan regulator in 5 steps, 240V, 50Hz complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix LED batten box type with CRCA sheet steel body pre-wired suitable for and including provision of 1x20Watt (4 feet) retrofit LED tube with PC body and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix of ceiling fans complete with blades, down rods, remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix of exhaust fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

Supply and fix LED building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65 degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fix MCB distribution board, TPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB all as specified and directed. Note: MCBs shall be measured and paid separetely.

S& F MCB TPN 63 Amp, 10 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

S& F MCB SPN 40 Amp, 10 KA, 'C' curve, 230 V, 50 Hz complete all as specified and directed.

All as per Ser item No 136 above but SP 6 to 32 Amp, 230 V complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 16 sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

M&L for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to copper strip 20x3 mm as earthing lead by means of bolts, nuts, check nuts and washers of copper and earth wire protected by 50mm dia GI pipe medium grade and connected to pole structure/ panel board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20x3 mm copper strip all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fix exhaust fan, 300mm sweep with 04 Nos of blade leafs, 70 W power consumption, 1300 to1400 RPM, 100 % copper winding heavy duty motor with double ball bearings including supply and fixing of metallic louvers and connecting up with 3 core x 0.5 sqmm flexible copper conductor cable from ceiling rose to connector of fan complete all as specified and directed.

Supplying and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 Sqmmm 2 core in service connections as per IS 7098 (Part-1) including connecting on LT OH line / LT panel/DB with suitable lugs, glads, binding wire etc complete all as specified and directed.

M&L for Tubes, 'Medium Grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 25mm bore complete all as specified and directed.

Supply and fix in replacement of Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe of size 25mm and fixed complete all as specified and directed.

Cutting and screwing of existing steel tubing for alterations or additions of size 40 or 50 mm done in position without taking down and inserting tee branch connection complete all as specified and directed.

Radha Govind Builders (BID ID -3059610)