SPECIAL REPAIRS TO BLDGS NO P-110 (DEF CIV ACCN) UNDER GE (W) COLABA, MUMBAI

Amount

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slab/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 25 mm average depth including saw-cutting of all edges making square shoulders of the cavities all as specified and as directed. Note:- (a) All loose unsound and cracked concrete shall be removed out side MD land (b) Thickness shall be measured excluding plaster)

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slab/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 40 mm average depth including saw-cutting of all edges making square shoulders of the cavities all as specified and as directed. Note:- (a) All loose unsound and cracked concrete shall be removed out side MD land (b) Thickness shall be measured excluding plaster)

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slab/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 60 mm average depth including saw-cutting of all edges making square shoulders of the cavities all as specified and as directed. Note:- (a) All loose unsound and cracked concrete shall be removed out side MD land (b) Thickness shall be measured excluding plaster)

Cleaning loose concrete if any all around reinforcement including from behind the reinforcing bars to give an average 10 mm thick (but not less than 10 mm clear air gap) and cleaning reinforcement of total rust using alkaline rust remover with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washed with water and allowing it to dry and Applying two coats of epoxy based passivating, protecting & bonding coat of zinc rich system (Nitozinc (R) primer of Fosroc and equivalent of SIKA/Dr Fixit Pidilite/ Krishna Conchem) as approved by the Engineer-in-Charge for old and new reinforcement any dia complete all as specified and as directed. omplete all as specified and as directed. Note : - Length of reinforcement bars cleaned of rust all around shall be measured for payment.)

M&L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height all as specified and as directed.

M&L mild steel TMT bars of any dia in stirrups, spaces and binders, cut to length, bent to shape required, inclcluding cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed

M&L plastering 20-25 mm thick (Average) epoxy based polymer modified cement mortar in two coats, 15 mm base coat and subsequent finishing coat with and including curing as per manufacturer's instruction all as specified and as directed by Engr-in-Charge. Make Dr fixit repair Pro-Polymer mortar, FOSROC- RENDOROC S2- structural grade polymer mortar or equivalent in STP/DR fixit . Note : - Ready to use bags will be used for the above item and no extra cost wiil be claimed by the contractor

Providing and placing in position micro-concrete, grade M40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section upto 75 mm all as specified and as directed by the Engineer in charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) Note : The item includes S&F of water tight centering and shuttering

M&L for RCC work as in columns, beams, slabs, chajja, railing in M-25 grade (Nominal Mix) using 20 mm nominal size crushed stone aggregate all as specified and as directed.

Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc. so as to withstand a pressure of 0.1 Mpa including removal of formwork from all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water and removing debris outside MD land (from ground floor to fifth storeys bldgs) including use of scaffoldings all as specified and directed.

Material and labour for 15mm thick Ready Mix Plaster in single layer of make / brand - ACC's Accoplast / CK Birla's Aerocon /Ultra tech cement, mixed with liquid water proofing compound on other than fair faces of brick wall or concrete surfaces, (upto 05 storeys of bldgs) including use of scaffolding complete all as specified and directed. Note :- Liquid water proofing compound will be measured and paid seperately as supply only.

Supply only liquid water proofing compound.

M&L for removing plants including roots by dismantling of brickwork/PCC including necessary scaffolding of any type and in any position or location i.e roof, parapet walls near pipes etc and applying acid after removing roots for preventing the re-growth & making good of disturbed portion using PCC 1:2:4 type B0 & 10mm thick cement plaster in CM (1:3), size of disturbed portion not execeeding 150mm X150mm X 200mm all as specified and directed.

M&L for filling cracks by cutting 'V' groove cracks of internal or external plaster of walls, ceilings/Chajjas all along the crack upto 10 mm and remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat and for external application must be coated with paint including necessary scafolding at any hieght all as specifed and direcetd. Make : Use of Dr Fixit Crack 'X' shrinkfree paste compound/ Smartcare Texture Crack Filler / Build Core Compound / Fosroc Compound, as approved by GE

M&L for cleaning all loose laitance on the wall and concrete substrate and applying one coat of epoxy bonding agent of SBR latex on exposed concrete surface to ensure bond between old concrete & new concrete by brush application including scafolding at any height as specified and directed. Make: Dr. Fixit epoxy bonding agent or Shalicrete URP of STP Ltd or Nerolac perma SBR latex

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises all as specified and as directed.

M&L screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes like tiles all as specified and directed.

M&L rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles all as specified and directed.

M&L digital coloured glazed ceramic tiles 300x450x7mm thick in vertical surfaces (including designed borders ) such as skirting and dados set and jointed in neat cement slurry and pointed in coloured cement to match the shades of tiles laid over rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed. Note:- (Rate of Designer border in vertical surface will be deemed to be included in quoted rates)

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles all as specified and directed. Make : Somany Pilkington / Orient bell / Kajaria.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, dados etc laid, bedded and pointed in any mortar and removal of rubbish off the site all as specified & directed.

M&L for granite (of any colour)18-20 mm thick machine cut, pre polished, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone as in kitchen platform, flooring , window cill, wall cladding including 15 mm thick screed bedding in cement mortar 1: 6 and all other similar works complete all as specified and directed.

Material and labour 20 mm thichk machine cut cudappa stone slab in horizental/vertical jambs laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including screed bedding 20 mm thick in CM 1:6 all as specified and directed by Engineer-in-charge..

Taking up or down steel tubing and connection including cleaning for refixing or removed to store,15 mm dia bore all as specified and directed

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 20 mm dia bore all as specified and directed

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 40 mm dia bore all as specified and directed

Fixing only old 15 mm steel tubing and including cleaning in positon (walls, ceiling and floor all as specified and directed

Fixing only old 20 mm steel tubing and including cleaning in positon (walls, ceiling and floor all as specified and directed

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed. Make: Jindal / Tata / Swastik

S&F GI tubing 20 mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed. Make: Jindal / Tata / Swastik

S&F GI tubing 40mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed. Make: Jindal / Tata / Swastik

Cutting chases, pinning in and making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n, exc. 10cm girth all as specified and directed.

S&F in repair counter sunk wash basin oval shape 550x460mm fixed with waste coupling & waste pipe & accessories of any size all as specified and directed. Make : Cat Part No 10095 of Hindware or equivalent in Cera / Parryware.

S&F as in repair 15 mm bore fancy type bib taps long body cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule all as specified and directed. Make:- ESS ESS CROMA Cat Part No C 202 or Equivalent of Jaquar

Supply and fixing 15 mm bore overhead shower of size 150x150mm single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 200 mm long (stainless steel) square shape with wall flange all as specified & directed. Make:- Cera Cat Part Not F7010506AB or Equivalent of Jaquar / Parko.

Supply & fixing in repair vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) including taking down existing squating pan all as specified and directed. Make : Cat Part No S3010104 of Cera or Equivalent in Hindware / Parryware.

S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of any size all as specified and directed. Make : Cat Part No B1010106 of Cera or Equivalent in Hindware / Parryware.

S&F PVC connection 15mm size PTMT nuts of length 450 mm all as specified and directed.

M&L in repair CP Towel Rail 61 cm long all as specified and directed.

M&L in repair CP soap dish all as per cat part all as specified and directed.

S&F in repairs 15 mm bore angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed

S&F in repairs 15 mm bore concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed .

S&F in repairs15 mm bore piller taps cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed shank and fly nuts all as specified and directed

M&L PVC (SWR) multi floor trap with grating including jointing with solvent cement for diameter of 75 mm outlet all as specified and directed Make: Prince/Supreme/Kisan/Reliance/Finolex.

S&F sinks made of stainless steel sink with draining board made out of 1 mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe including 40mm waste fitting overall size 915x460mm with bowl size 410x 330x160 mm all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided all as specified and directed

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided all as specified and directed.

M&L PCC 1:4:8 type D2 ( using 40 mm graded crushed stone aggegate) in foundation filling and mass concrete all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in roof, kerbs or mud stop rounded or chamfered edges all as specified and as directed.

M&L for applying three coat of polyurethane water proofing on new plastered surfaces as per manufacures instruction all as specified and direcetd

Material and labour for rendering 10 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces, with using liquid water proofing compound @ 200 ml per 50 kg bag of cement or as per manufracture's instructions, finished surfaces even and smooth without using extra cement all as specified and directed. Note: WPC shall be measured and paid for seperately under relevant item.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each all as specified and directed

S&F anodised aluminium section for doors, windows, ventilator door partition including fabrication of frame shutters and fixed with necessary lugs, cleats, rollers, handles, locking arrangement etc including all necessary accessories such as glazing clips, provn of AC opening and rubber beading for fixing glass beading for fixing glass panes in frame complete all as specified by Engr-in- charge. Note- (i) Glass panes will be measured and paid separetly. (ii) The quoted rate shall be inclusive of a cost of rubber beading and glazing clip hinges, handle however it will be not be weighteed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rsate. Make Hindalco/indl/Jindal or equivalent

M&L for 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side all as specified and directed.

Supply & fix stainless steel wire cloth , 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

Supply & fix in repairs stainless steel wire cloth , 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples in all as specified and directed.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary paint tint) (each coat) over a coat of pink primer including scafoldings of any hieght of bldg all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each complete.

Taking down shutter of any description area exc 1.00 sqm and n exc 2.00 sqm each all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19 x 19mm MS square tube suitably screwed all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes of size 15 x 15mm for top and bottom rails and 19 x 19mm for styles, MS frame covered with 5mm thick single piece extruded PVC profile 'C' channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming styles, and 5mm thick single piece extruded PVC profile for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2mm) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail; panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc all as per manufacturer's instructions and drawings as shown in SSR Part-I 2009 all as specified and directed.

Supply & fix for 2nd class hard wood plain, solid,straight chowkhat and frames, wrought framed, rebated on the solid rounded or chamfered, put together with glue pinned at joint all as specified and directed.

Material and labour for cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in hold fast, bed plates and all other similar works all as specified and directed.

Supply and fixing mild steel work in hold fasts, wall ties, pintle hinges and all other similar small articles conforming to Fe-290 Gde-E-165 all as specified and directed.

Supply & fix 35 mm thick 2nd hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face venners fitted to chowkhats all as specified and directed.

Supplied and fitted to chowkhats of 2nd class hard wood glazed and skelton shutter 30mm thick open rebated and prepared to receive glass, gauge etc with sash bars divided into square with plain chamfered or rounded mitred and rebated sash bars any member as in windows/ventilator stylles and rails provided as per SSR part -I Section 8 clause 8.24 (b) all as specified and directed.

Supply & fix 100 mm size butt hinges, heavy weight, cold rolled mild steel all as specified and directed.

Supply & fix aluminium anodised 150 mm barrel tower bolts of extruded section all as specified and directed.

Supply & fix mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate all as specified and directed.

Supply & fix 200 mm length aluminium anodised barrel tower bolt extruded section all as specified and directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolt with haps & staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as specified and directed.

Supply & fix 150 mm long aluminium handles, cast type, anodised all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as directed. Make : Asian - Apcolite or Berger- Luxol

S&F in repair 20 mm dia decorative fancy type SS curtain rods and all other connected works all as specified and directed.

S&F in repairs 20 mm dia decorative fancy type SS curtain rod brackets all as specified and directed.

S&F 18mm thick UV coating, HDHMR board exterior grade, including acrylic high gloss sheet of 3mm thick over HDHMR board, anti fungal, moisture resistence, anti borer, as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc. all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by GE . Make:-Action tessa/Greenply/ Century

S&F 18mm thick UV coating, MDF board exterior grade, both side laminated with any colour anti fungal, moisture resistence, anti borer, as per IS 14587 for kitchen/cupboards shelfs fixing with 1st class hard wood lipping/beading etc. all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by GE . Make:-Action tessa/Greenply/ Century

S&F in repairs of partial overlay / fully overlay hydraulic soft closing concealed hinges of size 103mm x 64mm finish of nickel/silver all as specified and directed by Engg-in-charge. Make : Godrej Kitchen appliances or other equivalent make as approved by GE.

S&F in repairs of stainless steel cabinet / drawers handle having a length of 250mm and shape all as specified and directed.

Demolition and breaking up drain pipe of 150 mm dia (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar all as specified and directed

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls all as specified and directed. Note : The aboe item inculde upto any height of builidng and including necessary scafolding

S&F 110 mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls all as specified and directed. Note : The aboe item inculde upto any height of builidng and including necessary scafolding

S&F 75mm dia PVC (SWR) bends with access doors any radius all as specified and directed.

All as per item No 87 above but without access door

S&F 110 mm dia PVC (SWR) bends with access doors of any radius all as specified and directed.

All as per item No 89 above but without access door

S&F 75mm PVC (SWR) branch piece, single (single Y) equal or unequal all as specified and directed.

S&F 110 mm PVC (SWR) branch piece, single (single Y) equal or unequal all as specified and directed.

S&F 110mm dia PVC (SWR) vent cowl all as specified and directed.

Dismantling asbestos sheeting/fibre/of any type & of any gauge, thickness, roof coverings including scaffoldings at any height all as specified and directed.

Dismantling of framed work of timber in scantlings 40 sq. cm and over in section, in any position all as specified and directed.

Supply & fix pre-painted galvalume aluminium zinc coating GI based trapezoidal/mangalore tile profile roofing sheets, chajjas, 0.50 mm thick of any colour/length having tensile strength of 550 MPA as in roof coverings having effective & overall width 1015 mm &1072 mm respectively, profile height 28.5 mm and centre to centre distance between ribs 203 mm fixed with self tapping screws as directed by manufacturer on wooden/steel members including scafoldings of any height of the bldg all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

S&F for MS joist, channel, angle, Tee, flat fixed independantly without connecting plates,etc Fe 410-W (Gde-E- 250) quality- A (cut to ordinary lengths i.e within 20mm of length indicated) as in frame work for Galvalume / CGI chajjas all as specified and directed.

S&F of structural steel work in tubular/square tube trusses including special shaped washer, gusset/bearing plate etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer all as directed . Make:-Asian/ Berger

M&L for disconnecting existing tanks exc 1000 & n.exc 2000 ltr capacity , setting aside( or lowering if reqd) for repair cleaning etc and hoisting if reqd reconnecting and refixing in position all as specified and directed.

M&L for applying two coats of weather proof acrylic exterior paint (100% Acrylic) (any height of building) including use of scaffoldings all as specified and directed. Make : Apex Ultima or equivalent

S&F cast iron arrow, tee, bends and designs of varoius pattern as per requirement at site for gates, rails, braces, etc., complete, drilled for fixing of hooks and hinges or steel hanging door fittings also fastening, welding and fixing including dismantling/ taking down old existing all as specified & directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of Oil bound distimper over a coat of Birla putty (average 2 mm thick) all as specified and directed. Make :- Asian paint (Emulsion Sparc),Berger (Rangoli) or equivalent makes.

M&L for providing and laying 40mm thick PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) with WPC Compound all as specified and directed by Engineer-in-Charge. Note:- WPC will be measured and paid seperately)

Priming the roof surface with bituminous primer conforming to IS-3384 @ 0.30 ltrs/Sqm and applying a coat of hot blown grade bitumen 85/25 conforming to IS-702 @ 1.20 Kg/Sqm and thereafter provide polymeric water proofing membrane (five layered) of weight not less than 3 Kg/Sqm with centre layer core of 90 micron high molecular density polyethylene film followed by another coat of semi hot blown 85/25 grade bitumen @ 1.20 Kg/Sqm blinded with fine sand in dry condition @ 0.50 Kg/Sqm all as specified (Make of polymeric water proofing membrane : M/s IWL India Ltd/M/s STP Texas Ltd/Bengal Bitumen)

M&L cement concrete coloured tiles with grey cement and no pigment 30 cmX30 cm x20mm thick machine pressed set, jointed and pointed including 15mm screed bedding in CM 1:6 as pointed in neat cement slurry in flooring as cut and poslished all as specified and directed

Making benching with PCC (1:2:4) type B0 using WPC along side wall adjoining to roof in concave shape all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed bese laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish inluding screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes all as specified and directed.

All as per Item No 109 above but in riser of steps, skirting, dado and pillar laid over cement screed and jointed over rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed.

BOB ENTERPRISES

SAHI SAGAR ENTERPRISES

SAHU AND SAHU CO.

Vandan Enterprises

Bright Construction Co

ASHOK CONSTRUCTION

Nilesh Construction

Unitech Enterprises

Frends Enterprises

Bidder Name

Unitech Enterprises

Frends Enterprises

Nilesh Construction

ASHOK CONSTRUCTION

SAHU AND SAHU CO.

BOB ENTERPRISES

Vandan Enterprises

Bright Construction Co

GANGAJAL

SAHI SAGAR ENTERPRISES