PROVN OF SEPARATE COMFORT STATION FOR LADIES AND GENTS AT MH AND SPECIAL REPAIR TO BLDG NO P-17 , P-18 UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

AC/SRW(BLDG)/05/2023-24 Taking down shutter and removing from site of any description size but exc 1 sqm and n.exc 2 sqm ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame without taking of shutter and removing from site exc 1.5sqm but not exceeding 4 sqm each ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame (w/o taking off shutters) and removing from site n.exc 1.5sqm each ; Complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster from wall's/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries upto distance n exc 500 metre ; Complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (un-reinforced)in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 50 mtrs ; Complete all as specified and directed by Engineer-in-charge.

Demolition of RCC in any position not otherwise specifically provided ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work ; Complete all as specified and directed by Engineer-in-charge.

Demolition of brick work built in cement mortar, seperation, cleaning and stacking of serviceable bricks for reuse and removal of debris,rubbish to a distance exc 400 m but not exc 500m ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work with sub Class 'B' old size bricks, straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work but except brick, built in cement mortar 1:6 Complete all as specified and directed by Engineer-in-charge.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. Complete all as specified and directed by Engineer-in-charge.

Material and labour for 10 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc Complete all as specified and directed by Engineer-in-charge..

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick work and finishing the surface even and smooth (without using extra cement) etc. Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper on walls Complete all as specified and directed by Engineer-in-charge..

Material and Labour for preparation of old decorated plastered surfaces, filling nail holes or patches with wall care putty to make surface smooth and applying two coats of oil bound distemper on walls ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying three coats of white wash on ceiling Complete all as specified and directed by Engineer-in-charge..

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall Complete all as specified and directed by Engineer-in-charge..

Material and Labour for complete removal of existing treament including preparation of surfaces and applying two coats of cement base paint on walls Complete all as specified and directed by Engineer-in-charge. .

Supply and Fixing solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube incl taking down old frame any type Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing Complete all as specified and directed by Engineer-in-charge. and directed Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Steel window 1.25mm thick box type ERW hollow P section of each frame size 60mmx25mm double rebated comprises of glazed & gaused Skelton shutter ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-06/07 i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) pintol hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c. (viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded (x) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in glazed / gazed skelton shutter of window (xi) 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane fixed in glaxed / gazed skelton shutter of window. (xii) Fabrication and fixing arrangements as per Drg No CE JZ/TD-06-07 including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg No. CEJZ/TD-06/07 dt 07.06.07 primer coated Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing pressed steel frames 1.25mm thick for door size of frame 105 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 30 mm thick flush shutter, soild core construction with block board core and plywood face panels commercial type on both side Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 35 mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of mamber of shutters as per SSR Part-I Section-8 clause 8.2 (a) Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 18mm thick PVC board in cup board shelve as in kitchen Complete all as specified and directed by Engineer-in-charge. (Make / shade / design / size as approved by Enginner -in-Charge)

Material and Labour for 18mm thick pvc shutter, printed one side with one coting of ultra violet chemical, glossymat finish inc 100% termite/water proof, fireretrandenteco friendly. Weight not less than 12 kg per sqm incl Steel piano hinges, steel catcher,aluminium handle100 mm long ,aluminium hasp & stapple in repairs ; Complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass any thickness, size, quality or description from steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes Complete all as specified and directed by Engineer-in-charge..

Supply and fixing stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples Complete all as specified and directed by Engineer-in-charge..

Supply and fixing in repairs stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples Complete all as specified and directed by Engineer-in-charge..

Supply and fixing 300mm size, aluminium alloy,anodized sliding door bolt, clip type, and fixing clips of sheets or extruded section and fixing of bolts and sliding bolts of extruded section fixed with stainless steel screw Complete all as specified and directed by Engineer-in-charge.

Supply and fixing butt hinges 100mm size medium weight cold rolled mild steel fixed with stainless steel screw Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs 150mm size aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screw Complete all as specified and directed by Engineer-in-charge..

Supply and fixing in repairs 300mm mild steel ordinary rat tail rod pattern spring including roller plate including fixing with nailsd/ bolts or weldedComplete all as specified and directed by Engineer-in-charge..

Supply and fixing in repairs 125mm size extruded aluminium anodized handle cast type fixed with stainless steel screw Complete all as specified and directed by Engineer-in-charge.

Supply and fixing mild steel powder coated curtain rods 22mm dia ( as per sample kept in GE's office) including knobs, brackets to hold the rod & a set of ABS finials ( as per sample kept in GE's office) of approved quality & appropriate qty of ABS plastic rings Complete all as specified and directed by Engineer-in-charge. .

Material & Labour for Preparation of new wooden surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old painted wooden surfaces of any description, over 10 centimetre width or girth and applying one coat of synthetic enamel paint ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for applying two coat of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces exceeding 10 cm width or girth including preparation of new surfaces ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old painted steel surfaces of any description, over 10 centimetre width or girth and applying one coat of synthetic enamel paint Complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed to walls, ceiling or laid in floor including taking down old steel water tubing Complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized iron steel tubing medium grade 20mm bore with all fittings and fixed to walls, ceiling or laid in floor including taking down old steel water tubing Complete all as specified and directed by Engineer-in-charge..

Supply and fixing Grating round 140mm size of PTMT ( minimum weight 50gms) ; Complete all as specified and directed by Engineer-in-charge..

Supply and fixing in repairs PVC connection 450mm long of 15mm size with PTMT nuts on both sides Complete all as specified and directed by Engineer-in-charge..

Supply and fixing bib tap standard 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) Complete all as specified and directed by Engineer-in-charge..

Supply and fixing Pillar taps 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-110gms) Complete all as specified and directed by Engineer-in-charge..

Supply and fixing in repairs stop valve 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) Complete all as specified and directed by Engineer-in-charge..

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC Complete all as specified and directed by Engineer-in-charge.. Note :- Flush pipe and flushing cistern to be measured and paid separately.

Supply and fixing white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle including pipe 32mm dia of PVC(Heavy duty) flush pipe including brackets and taking down/dismantling old unserviceable cistern complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections Complete all as specified and directed by Engineer-in-charge.

Supply and fixing rotational moulded polythelene water storage tanks(multi layer) capacity 500 litres(cylindrical vertical with closed top), with and including 20mm dia PTMT ball valve with epoxy coated aluminium rod ( minium weight 210gms ) hoisted, fixed in position and making connection including dismantling of existing unserviceable tank Exc 250 Ltr & not Exc 500 Ltr Complete all as specified and directed by Engineer-in-charge..

Supply and fixing swivel shower rose of PTMT for fixing with 15mm pipe ( minimum weight 40gms) Complete all as specified and directed by Engineer-in-charge..

Supply and fixing Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minium weight 190 gms) Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base and finishing the surface even & rough to receive floor finish Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Solid PVC Wall Lining consisting of 5mm thick Plain Colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete any description,fixed in any position Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 5 mm thk PVC sheet fillet of width 35mm for wall Paneling inclusive of fixing on to wall to make PVC Frame as /U channel per specification Complete all as specified and directed by Engineer-in-charge.

Dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises Complete all as specified and directed by Engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles Complete all as specified and directed by Engineer-in-charge.

Material and Labour for joint free Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 Complete all as specified and directed by Engineer-in-charge.

All as per Ser item No 62 here-in-before but as in skirting over 10mm thick cement plaster in 1:4. Complete all as specified and directed by Engineer-in-charge.

Dismantling of PVC/CI pipe of 75/100mm dia fixed with cement joint complete all as specified. Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR) pipes 110mm dia bend any radius Complete all as specified and directed by Engineer-in-charge

Supply and Fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PCC type D 2 (1:4:8) 40mm graded aggregate Complete all as specified and directed by Engineer-in-charge.

Material and labour for machine pressed coloured chequered cement concrete tile ISI Marked of size 30cm x30cmx22-25mm thick over and including 15mm thick cement screed in CM 1:6 set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles Complete all as specified and directed by Engineer-in-charge..

Material and labour for repairs of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of eight 1.5 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces Complete all as specified and directed by Engineer-in-charge.

Material and Labour for cement concrete 1:5:10 (40 mm graded aggregate ) in lean concrete Complete all as specified and directed by Engineer-in-charge.

Dismantling of brick tiles single layers on roof, jointed and grouted / pointed in cement mortar including cleaning serviceable tiles and stacking properly for re-use, disposal of unserviceable tiles and debris /rubbish from site Complete all as specified and directed by Engineer-in-charge.

Demolition of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs, sloping padding and finishing the surface even and smooth (without using extra cement) Complete all as specified and directed by Engineer-in-charge.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm includingcleaning surfaces etc Complete all as specified and directed by Engineer-in-charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces by forced application over entire roof area, sunken portion with overlapping 100mm to eiher side Complete all as specified and directed by Engineer-in-charge.

Material and labour for 40mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement Complete all as specified and directed by Engineer-in-charge..

All as per Srl item No 79 here-in-before but except tiles. Note : (i) Serviceable brick tiles obtained dismantling shall be reused. ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for udaipur green marble 16-18mm thick confirming to sample kept in GE 's office ( table rubbed and polished inslab, stair case, step and like jointed with grey cement slurry mixed with pigment to match with shade of marble over and including 15mm thick cement screed bed in CM (1:6) Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs CI floor trap( long nose) 75mm bore with grating including Jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) ; Complete all as specified and directed by Engineer-in-charge.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil ; Complete all as specified and directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/loose soil ; Complete all as specified and directed by Engineer-in-charge.

Removing Excavated soils exc 50m but n.exc 250m and depositing where directed at a level not exc1.5 M above the starting point. ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregates) for bed of sewage lines of 150mm dia including packing under and haunching against the sides of pipe after they are laid and tested ; Complete all as specified and directed by Engineer-in-charge.

Supply, laying in trenches, jointing and testing salt glazed stoneware pipe grade 'A' drainpipe 150mm bore confirming to IS at any depth over PCC bed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 2mm fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing mild steel Gde Fe-410-W as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel, hollow tube or flat sections) including distance pieces , cleats etc including welding of joint ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for 50mm thick cement concrete 1:3:6, type C-1,(using 20mm graded crushed stone aggregate) as in plinth protection, path finished even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc. ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade conforming to IS:694 drawn through and including non metalic rigid PVC conduit, medium grade, ISI marked, not less than 25mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and directed by Engineer-in-charge. (a) One light point/Fan point controlled by one switch/regulator NOTE: (i) Modular metal flush boxes concealed in wall with suitable cover plate for mounting switch, sockets, regulator etc. and cost of cutting chases & making good as existing to disturbed surface with cement mortar, if required any shall be deemed to included in the quoted rates. (ii) Modular fittings/fixtures such as switch, socket, regulator, etc., shall be measured and paid separately as under relevant item.

All as per ser item 92 here in above but One bell/buzzer point controlled by one bell push button independent ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 92 here in above but One 5 Amps outlet point on same board with other switches/sockets ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 92 here in above but One 3 pin 5 Amps socket outlet on independent board ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 92 here in above but point wiring with 4.0 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular switch 1 way 6A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular switch 1 way 16A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular fan step regulator, 2 module, 240 Volts, 50 Hz, suitable for ceiling fan 1200 mm sweep ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular bell push, one way, 6 Amps, 240 Volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings including 10cm x 10cm presto plastic board for resting to holder including Supply and Fixing 01 x 10/12 watts LED lamp, 230 volts Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing buzzer, Ding Dong, AC, 240 Volts, single pole, fixed over & including pressed steel sunk box of size 175 x 100 mm duly covered with 3mm thick bakelite sheet Complete all as specified and directed by Engineer-in-charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 12 way, 240 volts grade of make Legrand/L&T/Schnider with 200 Amps insulated rated bus bar, with poly urithene (PU) gasketing, earth bar IP- 43 & IK-09, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, with & incl suitable double compression S/s gland including taking down existing unsv one and removing from site Complete all as specified and directed by Engineer-in-charge. NOTE: DB & MCBs should be of same make

Supply and Fixing MCB of SP 5 to 32 Amps current carrying capacity, 240V, 10KA 'C' curve fixed in the MCB DB complete with connection testing and commissioning including taking down old unsv one from the site Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB SPN 32 Amps current carrying capacity, 240V, 10KA 'C' curve fixed in the MCB DB complete with connection testing and commissioning including taking down old unsv one from the site Complete all as specified and directed by Engineer-in-charge.

Supply and fixing sub main wiring with 2 runs of 4.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 1 run of 4.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down old unsv one from site Complete all as specified and directed by Engineer-in-charge. NOTE: Two runs of 4.0 sqmm copper cable and one run of 4.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan Complete all as specified and directed by Engineer-in-charge.

Supply, install & testing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 300mm complete of make Havells/Crompton/Orient, fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose to exhaust fan including cutting hole suitable for fixing exhaust fan Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing LED lights fitting 1x 20W, 220V, AC, 5700K, decorative box type with driver, double sided connection, CRI> 80, PF>95%, THD<10%, Lumen>2100 lm including LED tube light connecting up with 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Dusk & dawn roadway luminaries 45 Watt, 230 V AC, 5700K outdoor type with epoxy black powder coated sheet, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics, PF>95%, THD<10%, Lumen>4500 lm with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing all as specified and directed by Engineer-in-charge.

Supply & laying in trenches/drawn through pipes or in road crossing/floors/along poles/equipments etc., of XLPE insulated, armoured with multistranded aluminium conductor cable conforming to IS-7098 Part-I (1998), heavy duty, 1100 Volts grade of size 2 core 16 sqmm nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing, incl taking down old unsv one from site Complete all as specified and directed by Engineer-in-charge. NOTE: Excavation, earthwork, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Excavating in trenches not exc 1.5 meter wide and not exc 1.5 meter in depth for laying cables and getting out in soft/loose soil and in road cutting Complete all as specified and directed by Engineer-in-charge.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil Complete all as specified and directed by Engineer-in-charge.

Removing excavated material/surplus soil not exc 50 meters and depositing where directed at a level not exceeding 1.5 meter above starting point Complete all as specified and directed by Engineer-in-charge.

Supply & laying double wall corrugated (DWC) high density poly ethylene (HDPE) of size 40mm dia including all necessary fittings, PN-4 rating, pressure 6 Kgf/cm², conforming to IS-16205 (Part-24) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth of not less than 1.5 m below normal ground level, connected to glavanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts & washers and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 25mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade from top of the earth electrode raised upto a level of 50cm above ground level, MS funnel with wire mesh embeded in earthing pit of size 30x30x30cm in PCC (1:3:6) type C-1 incl exposed surfaces smoth finished with 15mm thick cement mortar (1:6), RCC pre-cast (1:2:4 type B-1) cover slab of 40mm thick with 2 Nos. MS handles of 12mm dia suitable for carrying of pit cover, Angle iron frame made out of 40x40x4mm angle iron for 30x30mm PCC pit for holding the pit cover including providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance n. exc. 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 Complete all as specified and directed by Engineer-in-charge. NOTE: (a) Cost of excavation, earth work, watering pipe, test point, MS Funnel with wire mesh and PCC pit with cover will be deemed to be included in the quoted rate. No extra cost shall be paid to the contractor against these items. (b) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor & no extra cost will be given to the contractor.

AC/LBW/02/2023-24 Surface dressing n exc 15 cm deep in soft/loose soil ; Complete all as specified and directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep insoft & loose soil ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour RCC M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in column, footings, plinth beams ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour RCC M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in columns ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour RCC M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in beams ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour RCC M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ; Complete all as specified and directed by Engineer-in-charge.

Formwork to sides of fair finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter ; Complete all as specified and directed by Engineer-in-charge.

Fair finished Square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions ; Complete all as specified and directed by Engineer-in-charge.

Fair finished flat Form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc ; Complete all as specified and directed by Engineer-in-charge.

Fair finished flat form works to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 using WPC 2% of weight of cement and finishing even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-charge. (WPC measured and paid saperatly)

Supply only integral water proofing compound ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 using WPC 2% of weight of cement and finishing even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-charge.. (WPC measured and paid saperatly)

Material and Labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3 finishing even and smooth without using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preperation of New plastered surfaces of walls and applying two coats of oil bound distemper over a coat of promer over and incl average 2mm thick birla wall putty ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for applying two coats of whitewash on ceiling including preperation of newly plastered surfaces ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying two coat of weather proof exterior paint over a coat of cement primer on wall surfaces ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Fadory made single extruded WIPC (Wood Polymer Composite) solid door window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules ofelasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length including taking down of old frames with shutters complete as per direction of Engineer-in-Charge NOTE: Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 300 mm long Aluminium alloy , Anodised , sliding door bolt with hasp , staple (bolt type ) and fixing bolts and sliding blots of extruded sections or cast aluminium alloy and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 150 mm long Aluminium handle cast type anodised ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading or galzing with putty including ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing figured glass pin head type, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading or galzing with putty including ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in bed blocks for hold fast & similar work etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 100mm thick Cement concrete type C-2 , 1:3:6 (using 40 mm graded aggregate) as in sub base ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing glazed ceramic coloured tiles 450x300mmx7mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing vitreous China Squatting pan 'Orrisa' pattren size 580x440mm white with integral foot rest and PVC(SWR) 'P' trap 110mm bore ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing vitreous China wash basin (Oval Type ) including CP waste fittings 32mm, waste pipe PVC 32mm bore of required size as directed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing centre hole mixer cast coppre alloy chromium plated with capston head (Pillar Mounted) srewed down high pressure with lettered hot or cold with long screwed shanks fly nut screwed for iron pipe 15mm dia ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC connection 15mm size with PTMT nuts of length 600mm ; Complete all as specified and directed by Engineer-in-charge.

Supply & Fixing vitreous china urinal half stall type white with grating and union for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Vitrous china urinal partition white of size 310x770mm of approved make and fixed to wall terminating about 40cm above floor line ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing rotational moulded polythene, triple layers, water storage tank 1000Ltr capacity, closed top, cylindrical, hoisted and fixed in position including Supply and Fixing 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Galvanised iron steel water tubing (Medium grade), 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Galvanised iron steel water tubing (Medium grade), 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Galvanised iron steel water tubing (Medium grade), 25mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 25 mm bore, Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing brass chromium plated angle valve 15mm bore fancy type screwed down for high pressure ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing soap dish, vitrous china white, approximate size 160 x 160 x 90 mm embedded in the wall ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Vitrous china white (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Chromium plated Health faucet with 1.5 metre long chain ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 15mm bore Stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup ( concealed type) and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 125mm CP shower rose fancy type with CP arm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 100mm dia CP grating with or without hinge type or hole type ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing CP brass towel rail 600mm long complete ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2mtr length including) including all fittings ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 75mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2mtr length including) including all fittings ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC (SWR) bends any radius With access door ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 50mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc ; Complete all as specified and directed by Engineer-in-charge. .

Supply and Fixing 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 50mm thick PCC 1:3:6 type C-1 (using 40mm graded stone aggregate as in plinth protection Finishing fair and even ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed by Engineer-In-Charge.( Min. thickness of powder coating 50 micron)

Supply and Fixing powder coated aluminium glazed shutter(for doors) Al-section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading. ( Min. thickness of powder coating 50 micron) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Aluminium powder coated (of any colour) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws , 4mm thick glass , Handle 02 Nos, Tower bolt 150mm 02 Nos , Honhes 75mm etc. ; Complete all as specified and directed by Engineer-in-charge. .(Min. thickness of powder coating 50 micron)

Supply and Fixing Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed in aluminium door as per specification and drawing ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door shutter of size 140mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Stainless steel mortice lock, 4 levers, verticle type, size 100 mm, ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Vitrified tiles,light shade 10mm thick (Square/ rectangular) polished, area of each tiles n.exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 20mm thick screed bed in CM 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 18 mm thick granite (of any type) (Table rubbed and polished ) in CM 1:4 incl pointing with white cement using marble dust of 1:2 with ad mixture of pigment to match with shade of granite over cement mortar plastering in CM 1:4 of 10mm thick etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing solid PVC board 18mm thick plain colour as in cup board shelves, kitchen cabinet etc. , ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing solid PVC shutter one side prelam of any shade 18mm thick plain colour as in cup board/ kitchen cabinet shutter etc. , ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing solid PVC sheet 5mm thick plain colour as in cup board, kitchen cabinet etc. , ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 40mm long self closing type Hydraulic steel hinges (Box type) in reapir suitable for kitchen cabinets & Cupboards ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 100mm long Brass handles, cast type, polished bright ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Shet glass corner shelf asseembly consisting of 5.5 thick glass corner shelf with chromium plated bracket guard and railing ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Paper dispenser complete set ; Complete all as specified and directed by Engineer-in-charge.

Supply & fixing vitreous china wash down water closet pan (padestal pattern) with flush pipe 32mm dia Eact for low level flushing cistern including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, PVC trap 110mm bore , ; Complete all as specified and directed by Engineer-in-charge. . (excluding flushing cistern).

Material & Labour for providing and fixing stainless steel (Grade 304) ralling made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slat with suitable arrangement ; Complete all as specified and directed by Engineer-in-charge.

Excavation in trenches in soft/loose soil not exceeding 1.5mtr wide and not exceeding 1.5 mtr in depth and not excceding 10 sqm on plan, getting out etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as concrete bed, laid to falls in trenches in any depth including packing under, and haunching against the sides of SGSW pipes 150mm bore, after the pipes have been laid and tested including ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for SGSW drain pipes 150mm bore laid in trenches and jointed incl demolition and breaking up drain pipes ( salt glazed ware, AC or Reinforced concrete ) set in cement mortar. ; Complete all as specified and directed by Engineer-in-charge.

Returning filling in the soil including spreading, levelling, watering and well ramming in layer n.exc 25cm thick each layer ; Complete all as specified and directed by Engineer-in-charge.

Removing excavated soil to a distance not exc 50m away and depositing where directed at a level not exc 1.5m above the starting point ; Complete all as specified and directed by Engineer-in-charge.

Cutting into existing manhole for connecting new drain pipe (150mm dia),making good to pipe and rendering, cutting out existing benching for and forming brench chennel in cement concrete 1:2:4 type B-1 smooth finished etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Brick work with sub class 'B' old size brick straight or curved on plan exc 6m mean radius built in cement mortar 1:4

Material and Labour for rendering 15mm thick on fair face of brick or concrete surface in CM 1:4 to be finished even and fair without using extra cement complete all as specified.

Material and Labour for precast RCC 1:3:6 type C-1 using 20mm graded stone aggregate as cover slab for manhole and similar work etc set in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for TMT bars 10mm dia and over cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PCC 1:2:4 type B-1 using 12.5 mm graded stone aggregates as in benching for manholes, bands, coping, bed plate etc including slightly chamfered or rounded angles including including necessary form work, if any, and finishing exposed surface even and smooth using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Hardcore of broken bricks gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 75mm thick Cement concrete type D-2 , 1:4:8 (using 40 mm graded aggregate) as in sub base ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 25mm sand filling under/over floors or in foundations including watering and consolidation ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Machine pressed pre-cast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Providing, cement concrete Type B1, 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade conforming to IS:694 drawn through and including non metalic rigid PVC conduit, medium grade, ISI marked, not less than 20mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and directed by Engineer-in-charge. (a) One light point controlled by one switch NOTE: (i) Modular metal flush boxes concealed in wall with suitable cover plate for mounting switch, sockets, regulator etc. and cost of cutting chases & making good as existing to disturbed surface with cement mortar, if required any shall be deemed to included in the quoted rates. (ii) Modular fittings/fixtures such as switch, socket, regulator, etc., shall be measured and paid separately as under relevant item.

All as per ser item 216 here in above but One exhaust fan point controlled by one switch ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 216 here in above but One 5 Amps outlet point on same board with other switches/sockets ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 216 here in above but One 3 pin 5 Amps socket outlet on independent board ; Complete all as specified and directed by Engineer-in-charge.

All as per ser item 216 here in above but point wiring with 4.0 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular switch 1 way 6A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular switch 1 way 16A, 240 volts, 1 module ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type all as specified and directed

Supply and Fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type all as specified and directed

Supply and Fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65 x 50 mm three terminal, 240 volts, AC single phase complete all as specified

Supply and Fixing Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings including 10cm x 10cm presto plastic board for resting to holder including Supply and Fixing 01 x 10/12 watts LED lamp, 230 volts complete all as specified and directed

Supply and Fixing sheet steel metal enclosure single pole & neutral with a 2 pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240 volts ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8 way, 240 volts grade with 200 Amps insulated rated bus bar, earth bar IP- 43 & IK-09, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB of SP 5 to 32 Amps current carrying capacity, 240 V, 10KA 'C' curve fixed in the MCB DB complete with connection testing & commissioning ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCB of SPN 32 Amps current carrying capacity, 240 V, 10KA 'C' curve fixed in the MCB DB complete with connection testing & commissioning ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing sub main wiring with 2 runs of 2.5 sqmm single core, multi-stranded PVC insulated, FRLS sheathed cable 1100 Volts grade with copper conductor drawn through and including non metalic PVC conduit, medium grade, not less than 25mm dia, ISI marked, with conduit fittings and accessories not less than 25mm dia concealed in wall/ceiling/floor including 1 run of 2.5 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-charge. NOTE: Two runs of 2.5 sqmm copper cable and one run of 2.5 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories not less than 25mm dia will be measured as one unit length

Supply and Fixing of wall mounted twin jet blower hand dryer of blower speed atleast 90 m/s and drying time of approx 10-12 sec ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, double sided connection, holder including LED tube light connecting up with 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Dusk & dawn roadway luminaries 45 Watt, 230 V AC, 6000K outdoor type with epoxy black powder coated sheet, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 40mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.2 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing ; Complete all as specified and directed by Engineer-in-charge.

Supply, install & testing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 300mm complete fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose to exhaust fan and writing MES No. including cutting hole suitable for fixing exhaust fan ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing storage electric heater (Geyser), flexible mounting of capacity 25 ltrs, single phase, 240 volts, AC, white colour, with incoloy heating element and PUF insulation, ISI marked BEE 5 star rated complete with high precision & externally adustable capillary thermostat for temp regulation, backup safety overheating capillary therrmal cut out at 95ºC, temperature display, etc., including provn of new suitable holding clamp, MS bolts, grouted to wall and connecting up including 3 core sheathed multi-stranded flexible copper conductor cable connected with 15/16 Amp plug top and provn of water connections with new PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers brass union, NRV of suitable size, check/end nuts with washers, 15mm dia 100mm long nipples (02 Nos) for hot water and cold water connections including writing MES No. and making good to the disturbed surface in cement morter as required and testing ; Complete all as specified and directed by Engineer-in-charge. NOTE: Cost of flexible copper cable of 3 core, PVC steel braided inlet/outlet pipe of 15mm dia, 450mm long with brass union, NRV, check/end nuts, nipples, MS bolts, etc., and minor parts, if any, other than those are not specified in the schedule and required for smooth functioning of geyser will be deemed to be included in the quoted rate

Material & Labour for earthing complete with galvanised earth plate electrode 600mm X 600mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 metres below ground level) with top edge of earth plate not less than 1.5metres below normal ground level, connected to GI Wire of size 4mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No.3 of MES SSR 2009, Part – I (Specifications) and connected to main switch board/LT feeder panel including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in alternate layers with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150mm both ways center to center with suitable lifting handle to cover, earth pit made of PCC 1:3:6 type C-1, GI protection pipe light grade 20 mm bore up to 7.5metres length from earth electrode including testing complete all as specified and directed NOTE: (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt. (iii) Rate quoted shall be inclusive of excavation and earth work and PCC all as specified in the item (iv) Earthing work will be carried out in the presence of MES representative

Supply and Fixing galvanised steel water tubes medium grade with screwed socket joint together with and including all GI fittings such as bends, elbows, short piece connectionns, backnuts, caps plugs and unions etc laid in tranches/fixed on walls/laid on floors of 25mm dia including testing ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing galvanised steel water tubes medium grade with screwed socket joint together with and including all GI fittings such as bends, elbows, short piece connectionns, backnuts, caps plugs and unions etc laid in tranches/fixed on walls/laid on floors of 20mm dia including testing ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for cutting CI/DI mains 100/150mm bore (in position) for branch connections of the internal dia 25 mm include for turning water off and on and draining as required ; Complete all as specified and directed by Engineer-in-charge.

Excavating in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for laying of pipe line and getting out in soft/loose soil and in road cutting ; Complete all as specified and directed by Engineer-in-charge.

Returning, filling in excavated material/soil including spreading, leveling, watering and well ramming in layers n exc 25cm in soil ; Complete all as specified and directed by Engineer-in-charge.

Removing excavated material/surplus soil not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meter above starting point ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing gun-metal, globe or gate valves conforming to IS:781-1984 of size 25mm with iron wheel head, screwed both ends for iron/UPVC pipe and fixed ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for construction of Brick masonry valve chamber (230mm thick wall) of 750x750x650mm internal size, PCC 1:4:8 type D2 using 40mm graded stone aggregate for foundation, brick wall with sub class 'B' bricks built in CM 1:6, PCC 1:2:4 type B1 using 20mm graded stone aggregate for coping rendering in CM 1:4, 15mm thick including provision of MS sheet cover 2mm thick fixed to MS angle frame made out of 40x40x4mm thick with 2 coats of synthetic enamel paint over one coat of red oxide primer to steel surfaces and locking arrangements with godrej lock including necessary excavation and earth work in any type of soil ; Complete all as specified and directed by Engineer-in-charge.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core ; Complete all as specified and directed by Engineer-in-charge.

Supply & laying double wall corrugated (DWC) high density poly ethylene (HDPE) of size 40mm dia including all necessary fittings, PN-4 rating, pressure 6 Kgf/cm², conforming to IS-16205 (Part-24) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable ; Complete all as specified and directed by Engineer-in-charge.

15ID/SRW(BLDG)/(ASR)-02/2023-24 (EM-PORTION) Taking down carefully the existing aluminium point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, regulator ; Complete all as specified and directed by Engineer-in-charge. Note cost of unserviceable materials will be charged from the contractor against schedule of credit.

Material and Labour for Wiring for one Light point/Bell/Fan point controlled by one switch complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including concealed conduit concealed/ fixed on wall / ceiling with sultable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, Fan regulators, etc, including provn of 1.5 samm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Wiring for One 3 pin 5 amps switch socket on independent board complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including concealed conduit concealed/ fixed on wall / ceiling with sultable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, Fan regulators, etc, including provn of 1.5 samm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Wiring for One 3 pin 5 amps switch socket on same board complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including concealed conduit concealed/ fixed on wall / ceiling with sultable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, Fan regulators, etc, including provn of 1.5 samm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly; Complete all as specified and directed by Engineer-in-charge.

All as per item No 251 herein before but with cable 2.5 sqmm (nominal area) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wire PVC insulated 1.5 sqmm copper multistranded conductor connecting to common earth and earth dolly complete all as specified and directed Note :- (a) The wiring shall be done in proper colour coding using red,yellow and blue for phase, black for neutral and green for earth leads.

Supply and fixing switch piano one way 5 A, SP, 230 Volts.; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Socket outlet 2 in 1, 3 pin 5 Amps Flush type.; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Switch outlet 2 in 1, 3 pin15 Amps Flush type.; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing stepped type electronic fan regulator flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling rose surface bakelite 3 terminals 65×32mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Lamp holder, credlycarbonale type with cord grip cap suitable for pendant/ballen fittings complete all as specified and directed by Engineer-in-Charge.

Supply and fixing wall/celing mounting LED 18Watt PC Diffuser tube light iting complete with all aceesories 1×18W LED suitable for domestic application 240Volts 50HZ including one tube rode and internally pre-wired with 1.5 samm twin twisted flexible copper conductor and ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing energy saving new generation 10 watt LED, 6000k bulk head luminaire with opal atfuser light fitting complete with all acessorles and connection complete all as specified and directed by Engineer-in-Charge.

Material and Labour for sub main wiring with PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications, 3 runs of 4 sqmm single core multistranded copper conductor PVC insulated cables as neutral continuity conductor drawn through and including one run of 25 mm dia rigid PVC conduit and conduit accessorles fixed on wall/ceiling etc., or concealed in wall and connecting to common earth dolly all as specified and directed including taking down all sub main wiring .

Supply and fixing in repair MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, 'B' curve type ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement of security light fitting LED 36 Watt aluminum pressure dia cast housing with touched glass cover IP-66 protection including suitable size and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with multistranded copper conductor of size not less than 1.0 sqmm from celing rose to fitting terminal including taking down old CFL security light fitting ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing GI bracket light grade GI Pipe 1.2 mtr Length for fixing of street light fitting 36/40 Watt including connection ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing MCCB Incomer distribution board double door vertical type made out of CRCA MS Sheet surface with insulated material like polyester or with epoxy powder coating surface mounting PN 8 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 KA 4 pole MCGB with thermal - magnetic setting and Icu = les = 100% ; Complete all as specified and directed by Engineer-in-charge. (Note: The cost of removing old wooden box and making good of surface as sonnented i die cost or removing old wooden box and making gun aniace as

Supply and fixing Celling fan five star rating 1200 mm sweep complete with including fitting and fixtures as per site requirement and complete accessories 230 Volts single phase 50 H2 AC supply and connectin up with and including two core PVC insulated, Pvc sheathed copper conductor ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing exhaust fan 300 mm sweep including cutting of wall /window/lowers and fixing arrangement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part - I (Specifications) and connected to main switch board / main DB's / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, gi funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, Gl protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 × 150 × 15 mm & painting of earth result etc. including testing on ; Complete all as specified and directed by Engineer-in-charge. Note (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

GEE EMM ASSOCIATES

Sai Construction Co.