PROVN OF TOILET BLOCK FOR OR AT 261 ARTY BDE CAMP AND MINOR WORKS AT P-2 CHURCH ROAD, P-17 AND 18 MALL ROAD, P-20 MANDIR MARG UNDER GE (EAST) DELHI CANTT-10

Amount

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundations etc or for shafts, wells cesspits, manholes, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed by Engr-in- Charge.

Returning & filling including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removal of excavated material n.exc 50 mtr and depositing where directed at level not exc 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 design mix as in foundation, including rafts , footings , foundation beams, plinth beams; bases for columns, etc ; basement slabs, under- reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 design mix as in columns, pillars, piers, posts and struts etc complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 design mix as in Beams , cantilevers, bressummers, lintels over 1.5 m span etc complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 design mix (RMC in roof slab and roof beam work through ready mixed concrete plant) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and shelves etc complete all as specified and directed by Engr-in-Charge.

M & L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required including cranking bending spirally & binding with and including mild steel wire (annealed) not less than 0.9mm dia etc complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in strirrups, spaces and binder and including mild steel wire (annealed) not less than 0.9mm dia etc complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams: and similar works; vertical or to batter for flat rough finished surfaces complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides and soffits of suspended slabs such as roof slabs , landings and similar work not exc 200 mm thick (horizontal or sloopping) for flat rough finished surfaces complete all as specified and directed by Engr -in Charge.

M & L for form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams etc for flat rough finished surfaces complete all as specified and directed by Engr -in Charge.

M & L for form work to sides of pillars, posts, struts, piers, columns and stanchions size of square, rectangular or polygonal for flat rough finished surfaces complete all as specified and directed.

M & L for form work to edges of concrete flats, treads breaks in floors , window cills , concrete railling, opening in concrete walls, floors and roofs RCC/PCC bands floors roofs n exc 20 cm wide and sides of RCC/PCC bands in walls , horizontal or slooping and similar work exc 10 cm and not exc 20 cm wide surface finished rough complete all as specified and directed.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, in half brick thick complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and fair complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and fair complete all as specified and directed by Engr-in-Charge.

M & L Rendering 5 mm thick on fair faces of concrete or concrete surface in ceiling in CM 1:3, finished even and fair complete all as specified and directed by Engr -in Charge.

Earth Soil spreading , levelling in layers n.exc 25 cm thick each layer with well ramming including watering as required under the floor complete all as specified and directed by Engr -in Charge. (Note :- Earth Soil available surplus soil from the excavation at ground )

M&L75 mm thick cement concrete type C-2 1:3:6 (40mm graded aggregate) as in sub base complete all as specified and directed.

M & L 25 mm Thick PCC type B-0 1:2:4 (12.5mm graded aggregate) as in flooring, under Tiles and etc all as specified and directed

M & L Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match laid over and including 15 mm thick avg screed bed in CM 1:6 complete all as specified and dirtected by Engr-in-Charge .

M & L Coloured Glazed ceramic tiles in vertical surface 600 x 300 x 7-8 mm thick, such as skirting, dados , etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match and over and including 10 mm thick screed bed in CM 1:3 complete all as specified and directed.

M & L for 18 to 20 mm thick granite (of any type) work( table rubbed and polished) in jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab over and including 15mm thick screed bed in CM 1:4 including rounding to edge of granite as per required complete all as specified and directed.

S & F box type steel ventilators with shutter including hings , handels ,galzing bar without wire mesh etc all as specified and directed.

S & F 3 mm thick sheet glass , ordinary quality and glazed with oil putty in square n. exc 0.5 Sqm in each pane fixed complete all as specified and directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F of factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam coloured PVC Sheet on both face, supplying & fixing in frame at site as per secification & directed

S & F Stain less steel Butt Hinges of size 100 mm with ss screw complete all as specified and directed

S & F150 mm size aluminium handles cast type anodised complete all as specified and directed

S & F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Material and labour for preparation of new surface decorated brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint over a coat of cement primer etc complete all as specified and directed by Engr -in Charge.

M&L for 3 coats of white wash on ceiling including preparation of newly plastered surfaces, complete all as specified and directed.

M&L for 3 coats of white wash on wall including preparation of newly plastered wall surfaces, complete all as specified and directed.

M & L for Framed work such as in door frame, door shuters / gate of angel, flat Iron, plates or other section complete prepared for fixing of steel sheeting or other convering doors to be prepared for hanging with and including hings, hold fast , handles , locking arrangement and all necessary required fittings of Fe 410-W (Gde E-250 quality - B) etc complete all as specified.

M&L two coat of synthetic enamel paint (finishing coat) over one coat of red oxide primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M&L for hard core of gauge n.exc 63mm deposited, spread and leveled in layers n.exc 15cm thick watered and rammed to a true surface with broken stone aggregate complete all as specified and directed by Engr -in Charge..

M & L 75 mm thick Cement concrete work as in plinth protection type C-1 , 1:3:6 (20mm graded aggregates) with finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr -in Charge.

S & F Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap with connection to drain and to flushing pipe antisyphonage pipe, including sheet cover and making good to floor complete all as specified and directed.

S&F Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to drain and to flushing pipe antisyphonage pipe, brackets for flushing cistern ,PVC (SRW) 'P' trap including provision of cement concrete bedding etc complete all as specified and dirtected by Engr-in-Charge .

S&F Vitreous China halfstall urinal flat back , size of 590 x 375x 390 mm white colour with including brass waste coupling and fixing with bottal trap (bottal trap paid separately) , providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, complete all as specified and directed by Engr-in-Charge..

S&F of 32 mm brass chromium plated bottle traps for wash basins/urinal with inlet and outlet screwed for pipe or connections including necessary packing, unions and cap and fixed, complete all as specified and directed.

S&F 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket ,32mm bore PVC flush pipe complete all as specified and directed

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S&F of CP towel rail 600mm long fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified.

S&F Vitreous China wash basin oval counter type white, size 600x425x195mm, with all fitting and fixture including fixing in granite slab and including brass waste coupling and fixing with bottal trap (bottal trap paid separately) complete all as specified and dirtected by Engr-in-Charge .

S&F steel water tubing galvanised 15mm bore medium grade fixed to walls, under floors and on ceiling surfaces or in chases including all fittings complete all as specified and directed.

All as per description of srl item No 50 above but 20mm bore.

S & F rotational moulded polythene, water storage tank 1000 Ltrs capacity, closed top, cylindrical, hoisted and fixed in position including 20 mm flot ball brass valves high pressure with polythene float and flynut complete, Aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 20mm - 210 gms) complete all as specified and dirtected by Engr-in-Charge .

S&F 15 mm angle cock/ stop valves, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore steel tubing complete all as specified & directed.

S&F 15 mm fancy type, chromium plated with long shank and cup (concealed type) stop valves, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore steel tubing

S & F 15 mm bore bib tap , chromimum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete all as specifed and directed.

S&F health faucet chromium plated ABS body with 1.00m CP long flexible pipe and brass chromium plate nuts & wall hook completed all as specified Make : Jaquar ALD-CHR-587 or equivalent as per list of makes.

S & F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S & F CP shower rose fancy type 150mm x 150mm size with 300 / 600 mm long shower arm to 15mm bore pipe complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S & F SS soap dish complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints ,laid on walls complete all as specifed and directed.

S & F 75 mm dia PVC cowls

S & F 100 mm dia PVC floor trap , with ss grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

S & F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joint laid in trenches or in floor completed all as specified and directed

S & F 110 mm PVC (SWR) bends with acess door completed all as specified and directed

S& F 110 mm PVC (SWR) junction single (Single T) equal or unequal with access door

M&L providing and applying the plaster with single component ready to use polymer modified repair mortar capable of applying 20 mm average thickness in single layer and finishing with trowel with a bond coat : SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area complete all as specified and as directed. (Make:- Asian Paints (Smart care) or equivalent in Sika, Fosroc and STP Ltd. Note : The application shall be executed on any type of surface and on horizontal/Vertical areas.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. (Make: Smart Care Damp Proof of Asian Paints or equivalent in STP/ FDSROC/ SIKA). Notes: (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) All materials shall be procured directly form manufacturer. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M & L for OUT DOOR coloured ceramic chequered tiles 8 to 9 mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified.

S&F steel work in tubular trusses, doors , posts etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed

Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for DWC (HDPE) (SN8) drain pipes of 150 mm bore laid in trenches and jointed and tested complete all as specified & directed.

M&L for concrete bed to drain pipe including packing under and haunching against the side of pipes, 150mm bore, in cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) after laying and testing of pipe complete all as specified and directed.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick plastering/rendering on brick work on concrete surfaces in cement mortar (1:3) mixed with liquid water proofing compound as per manufaturer's instructions finishing surfaces even and smooth without using extra cement complete all as specified and directed. (liquid water proofing compound shall be measured and paid sepretaely).

Supply only liquid water proofing compound complete all as specified & directed.

PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in benching for manholes, bands, coping, bed plate etc with slightly chamfered or rounded angles including necessary from work, if any, and finishing exposed surface even and fair without using extra cement complete all as specified & directed.

S&F Precast SFRC square or rectangular manhole covers 75 mm thick with frame medium duty conforming to IS-12592 including necessary reinfocement, complete all as specified and as directed.

M&L Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and as directed.

Surface excavation n.exc 30cm deep and getting 15cm deep avg. and getting out in soft/loose soil

M & L for 100 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing completed all as specified and directed.

M & L for 60 mm thick (two colour patern) factory made machine pressed precast cement concrete interlocking paver block any shape and size conforming to IS 15658-2006 M-35 grade ( colour, design and pattern as approved by GE) over and including 50mm thick compacted bed of dry sand, complete all as specified and directed.

M&L for factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required (Size and pattern as approved by GE).

M & L for preparation of new surface of plaster or concrete surfaces of any description over 10 CM width or grith and applying two coat of plastic emulsion paint over a coat of interior primer (colour and patren as per approved by GE) including complete all as specified and directed.

M&L providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified

Dismantling timber scantlings , posts, rafters, purlins etc 40 sq. cm and over in section, in any position, complete all as specified and directed.

Dismantling plain/ corrugated roof sheeting, any gauge, thickness, including , Nainital or similar pattern roof coverings sheet in any pattern & position of roof coverings.

Demolition of brick work built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkhats or frame with shutters exc 1.5 Sqm and n exc 4.00 sqm ditto but with shutters (without taking off shutters from the frame)each complete all specified and directed.

Taking down Cement Plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed

S & F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour as in ridges hips, vally gutter, drip and straight flashing , fixed with self tapping screws etc complete all as specified and directed

M & L Preparing of new plastered surfaces and applying two coats of oil bound distemper over a coat of interior primer and 2 mm thick wall care putty on wall, pillers, cornices etc complete all as specified.

M&L 75 mm thick cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) in sub base / floor etc complete all as specified and directed.

M & L Vitrified ceramic tiles (double charge) size 600 x 600 x 8 -12 mm thick (square/rectangular), (shade/ colour/ Design/ pattern as approved by GE) ,as in floors & skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 15 mm thick avg screed bed in CM 1:6 in floor and after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and dirtected by Engr-in-Charge

S&F in repair for 35 mm thickness flush shutters, solid core construction, with particle board core and plywood face panels both faces covered with decorative face veneer with lipping incl edge to match frame complete all as specified and directed.

S&F in repair 2nd class 35mm thick hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S& F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F Aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete.

S & F anodised aluminium frame for doors, windows, ventilators / AC provision window frame with or without three track window provision etc with Powder Coating (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Anodised aluminium window and ventilator shutters, powder coating of any colour, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 Nos) suitable handle (1 No) complete all as specified (Note : Glass / wiremesh etc any type paid separately)

S & F 5 mm thick sheet glass , ordinary quality in square n. exc 1 Sqm in each pane fixed complete all as specified and directed.

M&L 100 mm thick cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in floor, harstanding , ramp etc complete all as specified and directed.

M & L for Machine pressed rubber moulded vibro compacted precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80 mm thickness M-40 grade with Grey cement and pigment over 50 mm thick sand cushioning complete all as specified.

M&L 18-20 mm thick machine cut kota stone slab flooring jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed of CM 1:6 with neat cement slurry @ 3 Kg/Sqm over sub base including rubbing and polishing complete all as specified and directed by Engr -in Charge.

M&L 18-20 mm thick machine cut kota stone in riser of steps, skirting, dado and pillar laid over and including 10 mm thick screed bed of CM 1:4 including rubbing and polishing complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

M&L for Plain cement concrete 1:3:6 type C- 2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S&F rolled mild steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250), Quality B, complete all as specified and directed

S&F 1.25mm thick pressed steel frames size 125mm x 60mm for doors with double rebates including necessary fixing lugs/ hold fasts with PCC in walls /RCC etc, 6 or 8 Nos heavy MS hinges, lock strike plate, etc and including back filling with PCC in 1:3:6 (using 12.50mm graded stone aggregate) complete all as specified and as directed by Engr-in-Charge.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm as in floor set, jointed and pointed with coloured cement to match over and incl 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge including dismantling of exisiting tiles

S&F 15mm dia bore water tubing , medium grade , galvanised with all fitting laid to wall, ceiling or laid in floor including taking down old pipe complete all as specified and directed.

S& F 150 mm Floor Door Stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor

Demolition of cement concrete any description any any position not otherwise specifically provided for complete all as specified and as directed.

M&L two coat of synthetic enamel paint (finishing coat) over one coat of pink primer to new wood surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light point exhaust fan point controlled by one 1-way switch complete all as directed.

All as per srl item No 116 here-in-before but one socket outlet point 5 amps on the same board.

All as per srl item No 116 here-in-before but one socket outet point 5 amps on the independent board.

All as per srl item No 116 here-in-before but wiring with 2.5 Sqmm size.

S&F modular switch flush type, 6 amps one way,SP,230 volts AC all as directed.

S&F modular socket outlet 6 amps 5 pin 2 module all as directed.

S&F modular socket outlet 6 & 16 amps 6 pin multipurpose combined 2 module all as directed.

S&F modular switch flush type, 16 amps one way,SP,230 volts AC all as directed.

S & F of Ceiling rose, 3 terminal , pvc/polycabonate, isulated body all as specified and directed.

S&F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 20 Watt cool/warm white complete all as specified and as directed.

S&F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound 10 Watt , cool/warm white complete all as specified and as directed.

S&F of energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as specified and as directed.

S&F of bulk head fitting 10 W with PMMA diffuser complete all as specified and directed.

S & F of street light bracket incl clamp, nut and anchor bolt etc make to shape for street light fitting made out of GI pipe light grade 25 mm bore 1.0 mtr long on bend to shape the top of wall of existing building complete all as specified and directed.

S&F of Ventilating fan 250 mm sweep plastic body type including self cousing louver and making all electric connections, complete all as specified and as directed.

S & F of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed.

S&F of MCB C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA of capacity 6 to 16amps complete all as specified and directed.

S&F of Isolator suitable for 240 volts AC supply, SPN of capacity 32/40 Amps complete all as specified and directed.

S&F Geyser 35 litre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners (4 Nos) for hanging and CP and PVC connection for inlet and outlet upto stop cock, complete all as specifed and as directed.

Supply and fixing of Modular AC Socket with 25 Amps SP mini MCB, 230 Volts, 50Hz. In 4 module sheet metal enclosure complete all as specified and as directed.

Earthing complete with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers protected by and including 15 mm bore GI Pipe “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part-I including testing on completion complete all as specified and directed.

M&L for laying of LT underground cable XLPE insulated, PVC sheathed, galvanised steel strip / wire armoured, aluminium conductor, 1100 volts grade, of size 50 Sqmm 4 core suitable for earthed system laid in duct / trench / along pole / wall etc including making connection complete all as directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.2. The excavation, earth work, sand cushioning and brick protection etc will be measured and paid separately under respective items.

M&L for sand cushioning to under ground cable provided with layers of snad (8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

S & F of Galvanised steel tubing light grade of size 40mm bore with all fittings for passing cable complete all as specified and directed.

Drilling and tapping cast iron water mains (in position) for branch connection of the internal dia (15mm) complete all as specified and as directed.

M&L Tubes, 'medium grade bore dia (25mm)' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

M&L Gun-metal, globe or gate valves bore dia of (25mm) , with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

M&L Ball brass valves bore dia of (25mm), high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

M&L Straight plain brass bore dia (15mm) ferrules (or connecting screws) screwed both ends and fixed complete all as specified and as directed.

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc (to be measured and paid separately under relevent item of this Sch as S&F in repair and credit for these item given in credit schedule here-in-after) and making good the disturbed surface all as directed.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including MS Box with Plastic laminated sheet, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light / fan point controlled by one way switch complete all as directed.

All as per srl item No 147 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the same board.

All as per srl item No 147 here-in-before but with 1.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for one socket outet point 5 amps on the independent board.

All as per srl item No 147 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire independent board complete all as directed.

S & F in replacement switch piano, flush type, single pole one way 5/6Amp complete all as directed.

S & F in replacement socket, 2 in 1, 5/6A flush type. complete all as directed.

S & F in replacement socket 3 pin 5/16A, 5 in 1 flush type.complete all as directed.

S & F in replacement switch piano, flush type, single pole one way 15/16Amp. complete all as directed.

Supply and fixing in replacement Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

Material and labour in replacement submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm FRLS as earth wire in and including PVC conduit size 25 mm dia, medium grade with all fittings conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

S & F in replacement LED batten fittings 10Watts, cool/warm white complete all as specified and directed.

S & F in replacement LED batten fittings, 1x20Watts, cool/warm white complete all as specified and directed..

S&F in replacement of LED bulk head fitting 6.5 watt made of cast aluminium alloy with opal glass diffuser complete all as specified and directed.

S&F in replacement of piano type Step fan regulator, 120 watts complete all as directed.

Supply and fixing in replacement of Ventilating fan 250 mm sweep plastic body type including self cosing louver and making all electric connections complete all as directed.

Supply and fixing of Geyser 25 ltr capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners for hanging and CP and PVC connection for inlet and outlet upto stop cock including complete all as specifed and directed.

S&F in replacement of MCB DB conforming to IP 43 - IK 09 with double door, SPN 08 way, double door complete all as directed.

Supply and fixing in replacement of MCB 'B ' Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

S&F in replacement of Isolator SPN 40 Amp , 230 Volt ,all connections complete all as specified and as directed.

Supply and fixing in replacement ceiling fans complete with blades, down rods, and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) including taking down of old u/s c/fan & deposited to MES store yard. Make -Crompton/Havells/Bajaj

Material and labour submain wiring complete with 2 x 10.0 sqmm (nominal area) FR, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 10 sqmm FR as earth wire in and including PVC conduit with all fitting such as tees, bends, elbow, reducers etc complete all as directed.

M/s Shubh Enterprises (BID ID -3128492)

LAXMI GROUP (BID ID -3117673)

Akhil Enterprises (BID ID -3117084)

Vipul Construction (BID ID -3127794)

V M CONSTRUCTION (BID ID -3106300)

M/S GEETANJALI ENTERPRISES (BID ID -3116968)

VIJAY KUMAR GUPTA (BID ID -3128255)

M/S SIMRAN CONSTRUCTION CO (BID ID -3109374)

M/s Pankaj Contractors & Engineers (BID ID -3114214)