Construction work of Examination Block under Nilambar Pitambar University, Palamu

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Extra for each subsequent lead upto 25 M beyond the initial lead of 50 M ( Maximum upto 150M lead by head load) as per specification and direction of E/I. (UPTO 100m = 4*13.99)

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 2.35.3.1 With Chlorpyriphos E.C. 20% with 1% concentration

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75Bwork in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. @ Size of Tile 600x600 mm .

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. @ Size of Tile 600x600 mm .

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.,

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and laying cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : ,….. 1:2:4(1cement:2coarse sand (zone-III):4 graded stone aggregate 40 mm nominal size)

Providing P.C.C. M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20mm to 6mm size graded and mixing cement sand of F.M 2.5 to 3 including screening, shuttering, vibrating, skirting, curing, taxes and royalty all complete all complete as per specification and direction of Engineer-incharge.

Providing R.C.C. M-200 with nominal mix of (1:1.5:3) in lintel with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position vibrating, skirting, curing, (but excluding the cost of reinforcement, taxes and royalty all complete job as per building specification and direction of E/I.

Reinforced cement concrete work in beams, suspended floor, roofs having slove uo to 15° landing , balconis , shelves, chajjas , lintels, bands, plains window sills , stairases and spiral stair cases above plinth level up to floor five level , excluding cost of centering, shuttering , finishing and reinforcement . 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 grade stone aggregate 20mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 grade stone aggregate 20 mm nominal size).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for :- Columns, Pillars, Piers, Abutments, Posts and Struts

Providing designation 100 A brick work with fly ash lime brick ( flag) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. ( 1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints , cost of screening materials , raking out joints to 150 mm depth , curing , taxes and royalty all complete

Providing Designation 100A 112 mm thick reinforced B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 12 mm. cement plaster ( 1: 6) with clean coarse sand of F.M. 1.5 including screening , curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper ,applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction E/I.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for c????ing and fo?? final ??e????.??All abo??e ope??a??ion?? ??o be done in o??de?? and a?? di??ec??ed and ??pecified b?? ??he Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

10 MM AS PER BBS

12MM AS PER BBS

16 MM AS PER BBS

providing Tor steel reinforcement of 20mm,25mm,& 28mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1 mm thick

Providing and fixing bright finished brass 100 mm mortice latch andlock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinea(a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:r portions of the building for all heights and all levels, including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural gla Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately.zing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in- Charge.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm. At 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.TRUSS

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m2

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places

Providing single layer naria tiles in roof including cost of all labour and materials, taxes all complete as per building specification and direction of E/I

Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge.

Providing expansion joint in roof slab and terrace, joints filled with bitumen filter or impregnated fiber board etc all omplete as per specification and direction of engineer in charge

Providing and fixing of façade at all heights with extruded Hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of > 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L'(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400mm c/ c matching to the tile horizontal grid with two numbers of selfdrilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets 26.92.1 With 16mm thickness (+/- 10%) terracotta tiles of grey colour

Cutting of trees, excluding removal of stumps and roots of trees

Removal of stumps and roots including backfillinbg with suitable material to required compaction

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade providing approved jointing materials and joints properly fillrs to make them lead proof including providing sight rails, bonning rod, night, guard, Red light and barrier etc. all complete as per specification and direction of E.I.150mm dia R.C.C. spun pipe

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Supplying NP2 R.C.C. hume pipe with collars as work site as per direction of E/I.150mm dia R.C.C. Pipe

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing 15 mm dia male ended C.I .Body brass spindle valve and seat bib cock of approved quality (wt not less than 400 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l .

A) BRASS STOP COCK

(a) 15 mm dia

(b) 20 mm dia

Providing and fixing 15 mm dia and 45 cm. long P. V .C connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of E/l .

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 15 mm dia wt not less than 300 gms

(a) 20mm dia wt not less than 400 gms

(a) 25 mm dia wt not less than 500 gms

(a) 32 mm dia wt not less than 700 gms

(a) 40 mm dia wt not less than 1kg

(a) 50 mm dia wt not less than 1.5 kg

Cutting drain width wise above G.L for laying G.I pipes and restoring with brick in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.

(a) Glass shelf with C.P brass rail

(b) Mirrors of 4 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.

(i) 125 mm dia

(ii) 250 mm dia

(iii) 375 mm dia

(iv) 500 mm dia

(v) R.C.C. chajja

Supplying labour and tools for laying and jointing UPVC pipe and making joints with UPVC collar and solvent cement including … as per specification and direction of E/I

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

110mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

Coupler 110 mm dia

Single Tee with door

Bend 87.5 deg 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

PVC Shoe

Providing and fixing unplasticised- PVC pipe clip of approved desing to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwes with M.S. Screw of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 Cement : 4 Coarse sand ) and making good the wall etc. complete.

110mm dia

U-PVC Pipes (working pressure 4 kg/cm2) single socketed pipe 75mm dia

U-PVC Pipes (working pressure 4 kg/cm2) single socketed pipe 110mm dia

U-PVC Pipes (working pressure 4 kg/cm2) rubber seal 75mm dia

U-PVC Pipes (working pressure 4 kg/cm2) rubber seal 110mm dia

U-PVC coupler for UPVE drainage pipe 75mm dia

U-PVC coupler for UPVE drainage pipe 110mm dia

U-PVC single equal tee (without door) 75x75x75

U-PVC single equal tee (without door) 110x110x110

U-PVC single equal tee (with door) 75x75x75

U-PVC single equal tee (with door) 110x110x110

U-PVC bend 87.5 degree 75mm bend

U-PVC bend 87.5 degree 110mm bend

U-PVC plain shoe 75mm

U-PVC plain shoe 110mm

U-PVC pipe clip 75mm

U-PVC pipe clip 110mm

Providing and fixing white vitreous china battery based infrared sensor operated urinal of appx.size 610x390x370mm having pre & post flushing with water (250ml & 500ml consumption) having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturers specification & direction of Engineer-in charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

65 mm nominal bore

80 mm nominal bore

Providing and fixing C.P. bass angle valve for basin mixer and geyser points of approved quality conforming to I.S:8931.

15 mm nominal bore

Supplying pig lead at site of work

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

Providing and placing on terrace (at all floor levels) storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license].

Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m.

up to 1.50 m depth

Pipes 80 mm to 300 mm diameter

1.50 m to 3.00 m depth

Pipes 80 mm to 300 mm diameter

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete.

150 mm. dia. RCC Pipes

250 mm. dia. RCC Pipes

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

150 mm. dia. RCC Pipes

250 mm. dia. RCC Pipes

Construction brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.Inside size 90 x 80 cm and 45 cm deep including CI cover with frame(medium duty) 500mm internal diameter, total weight of cover and frame to be not less than116 kg (weight of cover 58 kg and weight of frame 58 kg).-With FPS bricks of class designation 75.

Inside size 120 X 90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg).With FPS bricks of class designation 75

Extra for depth for manholes

Size 90x80cm with FPS bricks of class designation 75

Size 120x90cm with FPS bricks of class designation 75

Providing and fixing square mouth SW gully trap class SP-1 complete CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.7 kg. as per standard design.

100x100mm size P type

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Constructing brick masonry road gully chamber 50 X 45 X 60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500 X 450 mm precast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Boring/drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS:2800 (part-1) including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer-in-charge, upto 90 metre depth below ground level.

300mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS : 12818, including hire & labour charges, fittings & accessories etc, all complete, for all depths, as per direction of engineer-in-charge.

100mm nominal size dia

Supplying & filling, sepreading & leveling stone boulders of size range 5cm to 20cm, in the recharge pit, in the required thickness, for all leads & lifts, all complete, for all depths, as per direction of engineer-in-charge.

Supplying & filling, sepreading & leveling gravels of size range 5mm to 10mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads & lifts, all complete, as per direction of engineer-in-charge.

Supplying & filling, sepreading & leveling coarse sand of size range 1.5mm to 20mm, in the recharge pit, in the required thickness over gravel layer, for all leads & lifts, all complete, as per direction of engineer-in-charge.

Providing and fixing Bail plug / Bottom plub of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (part -1)

200mm dia

Providing and fixing in position pre-cast RCC manhole cover and frame of required shape & approved quality

Circular shape 560 mm internal diameter-EHD-35

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 ( 1 cement :4 coarse sand) with precast R.C.C. vertical grating complete as per standard design:

With common burnt clay F.P.S. bricks(non modular) of class designation 7.5

Supply installation testing and commissioning R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 120 lph.-Kent/approved equal make.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of jaquar/kohler/hindware or similar approved brand and make, shape, size, and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gaskets etc including making connection with the existing P/S trap, complete in all respect as per the direction of engineer in charge

Providing and fixing wall mounted extended white vitreous china water closet of jaquar/kohler/hindware or similar approved brand and make, shape, size, and pattern including integrated white vitreous china cistern of capacity 10/6 litres with dual flushing system including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gaskets etc complete in all respect as per the direction of engineer in charge

Providing and fixing white vitreous thin rim table top/support mounted wash basin of rectangular/oval/round shape of size 600 x 415 x 200 of jaquar/kohler/hindwar or similar approved make

Providing and fixing PTMT 15mm urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms

Providing and fixing PTMT 15mm urinal cock 80mm long, 42mm high and 30 mm wide of jaquar/kohler/hindwar or similar approved make

Providing and fixing 600mm long tower rail weighing not less than 190 g of jaquar/kohler/hindwar or similar approved make

Providing and fixing PTMT towel ring of circular/square or trapezoidal shape weighing not less than 88 g of jaquar/kohler/hindwar or similar approved make

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high, 112mm distance from wall of standard shape and size weighing not less than 105 gms

Providing & fixing Sink Mixer with Swinging Casted Spout (Wall Mounted Jaquar model CON-319 KNB/approved equal) with 450mm long copper pipes & brass nuts.

Providing & fixing C.P. brass shower assembly consisting of wall mixer (Jaquar model no. CAN-281kn), wall flanges and shower rose (Jaquar 489) & pipe upto shower rose complete.

Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall hook. (Jaquar model no. ALD-573 L 1500).

Providing and fixing exposed part kit single lever basin mixer / pillar cock wall mounted / floor mounted including sleeve, flange, nipple, spout and other fixtures of jaquar/kohler/hindware/ similar approved make as per the directions of E/I

Brick chamber 600 x 600mm with dry joints.

Filled with loose brick ballast for good infiltration.

Excavation ( in all types of soil ), back filling & disposal of surplus earth as directed at site.

1no. SFRC heavy duty manhole cover 600mm dia with lifting lugs & frame.

Rungs at 300mm c/c

Cost include all associated civil works like excavation , back filling & disposal of surplus excavated earth as directed at site.

Constructing Oil & Grease Chamber size 2500x 1200mm internal size of 1000mm depth in brick work of class 75 with cement mortar (1:5) Inside 12mm thick with cement mortar 1:3 with floating coat of neat cement and rough plaster on outside, RCC top slab with 500mm dia medium duty manhole cover with frame (weight of cover 58 kg. & weight of frame 58 kg.), 150mm thick foundation concrete (1 :4 : 8), necessary excavation, dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required.

Supply & erection of ISI marked portable fire extinguishers, wall mounted type, wall brackets complete in all respect as per standard item with all accessories, delivery hose & nozzle whereever required, including fixing on walls as per the directions of Engineer-in-charge.

(MAKE : Minimax / Cease Fire / Safex / Padmini / Newage)

Water CO2 gas nozzle type. 9 Lt.capacity (IS:15683)

Mechanical Foam gas cartridge type. 9 LIT. capacity (IS:15683)

ABC dry powder stored pressure type 6 kg. capacity (IS:15683)

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

200 mm dia. (WALL THK - 6.3 mm

150 mm. dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

65 mm dia

80 mm dia

100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40mm

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Providing & fixing standard carbon steel fireman axe with rubber insulated handle tested to 20000 Volts.

Providing and fixing weather proof standard fire hose cabinet (900 mm x 1800 mm x 600 mm) outdoor type made of not less than 14 SWG MS sheet having glassed hinged door (5 mm thick glass) including necessary locking arrangement with handle for housing hydrant valve, two nos.15 meter long fire hose pipes, branch pipe as required as per drawings, including brackets for mounting accessories, painting (one coat primer and two coat of fire red colour). The cabinet shall be mounted on self standing mounted type painted MS Angle iron frame as required. The words "FIRE HOSE" to be painted on the box.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

1620 lpm at 56 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

300 lpm at 56 m head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35 m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Horizontal side wall sprinkler

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

40 mm nominal outer dia pipes.

50 mm nominal outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings. This including jointing of pipes & fittings with one step CPVC solvent cement , trenching, refilling & testing of joints complete as per direction of Engineer in charge.

40mm Nominal outer dia pipes

62.5mm Nominal inner dia pipes

Providing, fixing, installation, testing and commissioning of Solar Hot Water indirect Heating system using approved type of heating liquid medium comprising of flat plate solar panels, with single sheet absorber fin ,screw less construction of panel,including all interconnecting insulated GI piping, primary and secondary recirculation pumps, pressure type insulated hot water tank wit PUF insulation, sacrificial magnesium anode with steel core including valves on inlet, outlet, Y strainer and a water meter on the inlet, air release valve all mounted on galvanized MS sections complete as required with connection with existing piping. (connect the system to hot water mixing tank via 50 mm dia pipe) (make: Solarhart ,Tata BP ).

Supply, Instalation, Testing & Commissioning of 100 LPD flat plate solar collector panels of 2 x 1m size approx. the panels enclosed in insulated collected boxes with single piece toughened glass 3.5mm thick and fixed with heat resistant.panel Should have a single sheet absorber and screwless design. (make:Solar hart ,Tata BP ).

a) 100lpd MS insulated tank 2coats of primer & painted (sheet thickness 4mm).

b) Inter-connected insulated GI piping insulated with 9mm thick nitrile rubber heat resistant insulation sections (Vidoflex or equivalent) and valves with outer mechanical protection of aluminium sheet cladding.

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB . Group C

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required. Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB/HPL

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required. Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB /HPL/Anchor

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Wiring for power plug with 2x4 sqmm FR PVC insulated copper conductor single core cable in recessed PVC conduit alongwith 1 No. 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.( Make-Polycab/Incab/Mescab/Havells/ KEI/RR Kable)

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2x4 Sqmm +1x4 sqmm earth wire- for LDBs & UPS DBs

2x6 Sqmm +1x6 sqmm earth wire- for PDB

4x6 Sqmm + 2x6 sqmm earth wire- LDBs & UPS DBs

4x10 Sqmm + 2x6 sqmm earth wire PDBs

Supplying and fixing Modular type blanking plate-Supplying and fixing modular blanking plate on existing modular plate switch box excluding modular plate etc. as required.

S/F 20amps, 230 Volts SPN MCB Industrial Socket : Supplying and fixing of 20 amps, 240 volts industrial socket outlet , with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc as required.

S/F 20amps 415Volts TPN MCB Industrial Socket : Supplying and fixing of 20 amps, 415 volts industrial socket outlet , with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, TPN, MCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket 4ut let and complete with connections, testing and commissioning etc as required.

Supply fixing(S/F) following sizes of medium class PVC Conduit along with accesseories in surface/recess including cutting the wall and making good the same in core recessed conduit etc. as required.

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.

5/6 AMPS, one way switch

5/6 Amps, 3 pin socket outlet

TV antena socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Bell push

S/F Modular Boxes, base & cover plate: Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module (75 mm x 75 mm)

4 or 5 module(78 mm x 140 mm )

8 or 9 module(78mm x230mm)

TV Cable in Existing Conduit: Supplying and drawing of co-axil TV cable RG-6, grde copper conductor, PE insulated, with PVC sheath in the existing surface / recessed steel / PVC conduit as required.

Ceiling Rose: Supplying and fixing 3 pin,5 amp ceiling rose on existing junction box/wooden block including connection etc as required.

S/F Electronic Musical Call bell: Supplying and fixing electronic musical call bell suitable for D.C/A.C, single phase 230 volt, complete as required.

ITC fluorescent fitting with down rods :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, including supplying and fixing ball and socket arrangement, 2 nos. down rods of 20mm dia stee.

Supplying and fixing the follwing way single pole and neutral sheet steel M.C.B distribution board, 240 volts in surface/recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, interconnection including earthing etc. as required(without MCB/RCCB/Isolator). Make-Havells/Legrand/ Polycab/ C&S/ Polycab/ABB / HPL

12 ways, double door( UPS=2, LDB=1, PDB=1)

Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator).

4 way(4+12) Double door Horizontal type( UPS)

6 way(4+18) Double door Horizontal type((PDB=3)

8 way(4+24) Double door Horizontal type(LDB=5 , PDB=2)

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

40A DP MCB

63A DP MCB

40A TPN MCB

63A TPN MCB

S/F TPN RCCB: Supplying & fixing following rating, TP&N 415 V, residual current circuit breaker(RCCB) , having a sensitivity current upto 300mA in existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps for lighting DBS+UPS DBs

63 Amps for power DBs

Supply and Fixing Vertical TPN MCB DB

Supply and Fixing testing and commissioning of three pole and neutral, sheet, MCB distribution board, 415V, copper bus bar, earth & neutral bar, removiable gland plates, cable glands including connections with outgoing feeders complete all respect. ( but without MCCBs & MCBs)

4 way(8+12) Double door Vertical type

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 A, 16 kA, FP MCCB as incomer of VTPN DB

MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- Finolex / Polycab / Havells / Mescab/KEI

3.5CX 25 sq. mm armoured AL Cable

3.5CX 35 sq. mm armoured AL Cable

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 kV grade of following size on wall surface as required.

upto 55 sq.mm( clamped with 1mm thick saddle)

1.1kV Cable End Termination: suppluing and fixing indoor cable end termination with brass double compression gland and AL lugs of following sizeAl armoured cables.

3.5Cx25 sq.mm

3.5Cx35 sq.mm

Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but with charcoal or cock and salt) complete etc. as required. Lightning Conductors=4 nos + DBs+UPS).

S/L 8 SWG copper wire in ground :- Supplying and laying 8 SWG copper wire at 0.50 metere below ground level for conductor earth electrode, including soldering etc. as required.

Providing and Fixing Lightning Conductor Finial : P/F of lighting conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85mm dia 6mm thick GI base plate including holes etc. complete as required.

GI lightning conductor tape in horizontal run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.

GI lightning conductor tape in Vertical run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.

BLDC Ceiling Fan: Supplying , installation, testing and commissioning of 1200 mm (48")Sweep BLDC 5 star, 32W AC ceiling fan confirming to IS:374:2019 , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC

Exhaust metal Fan 230mm(9"): Supply , installation and commissioning of 230mm(9"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/ Havells/Crompton/GE)

LED tube with Batten 20W: Supply , installation and commissioning of wall mounted LED 20W tube light suitable for 230V, single phase supply voltage, with all accessories like batten and electronic driver others as required. ( Make -Bajaj/ Havells/ Philips/ Jaquar)

Surface/Recess mounted 20W LED round : Supply , installation and commissioning of Environmental friendly, new generation,aesthetically designed, ultra modern surface/recess mounting luminaire with high brightness 20W LEDs as light source.( make : Havells /Bajaj/ Wipro/Jaquar)

Surface/Recess mounted 2'x2' LED Panel light : Supply , installation and commissioning of Environmental friendly, new generation,aesthetically designed, ultra modern surface/recess mounting luminaire with high brightness 2'x2' panel light shall confirm to IS : 10322 part-5/ section-2 or IEC: 62722.( make : Havells /Bajaj/ Wipro/Jaquar)

LED Flood Light 150W:Supply installation Testing and Commissioning of LED flood lighting( 150W ) luminarie with prssure die cast housing and toughened glass cover (IP-66 protection in existing pole/ pipe for supply voltage 100-270 volts AC, 50Hz. Luminarie shall confirming to IS:10322 part-5/ section -5 and shall be conecessary accessories as per required. ( Make -Wipro/Bajaj / Havells/ Jaquar)

Supply of Wallmounted Fan(16"/400mm): Supply , installation and commissioning of 400 mm Sweep wallmounted fan , including connection with 1.5 sq mm copper wire with all accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC.

Supply & erection of LED 10W Bulk Head: Supply and erection commissioning of LED bulk head comprising of pressure die cast housing with acrylic diffuser(IP 65 protection)d clear glass. Make- Bajaj /Havells/Jaquar)

Silent type DG set of 62.5 KVA Three Phase with AMF panel IS/IEC-60034-1 IS:1460 IS:13018

Supply and installation of Off Grid Solar power backup system with solar panel waree/UTL 540 WP X 130 nos UTL Star Online 120KVA 360 VDC Solar Online PCU, UTL UST 2060 200 AH * 30 Nos with wiring lightning arrestor and earthing complete as per specification od Engineer In charge

Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

25mm dia

32mm dia

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required.

2x1.5 sq mm

2x2.5 sq mm

Supply, installation, testing and commissioning of smoke detector with built in LED and munting base complete with all connections as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of manual call Each boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning response indicator Each on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying Fixing Lift of Following Specificaion 13 passenger:- PRODUCT:-GeN2-Nova or equivalant, DETAILS, GeN2-Nova VXN, CAPACITY (kgs)-884 Kg, 13 persons. , SPEED (mps)-1 mps, RISE (m)-14.4 m, STOPS-3 Stops With (all opening on the same side), CONTROLLER TYPE-ACD3-MR, DRIVE-VF Regenerative (Closed Loop), POWER SUPPLY-400/415 Volts (3 Phase AC), OPERATION-Full collective operation, CAR GROUP-One car (simplex), MACHINE- PM Gearless (Located above shaft), TRACTION MEDIA-Flat Coated Steel Belt, CAR FINISH-•Rear Mid Panel = Stainless Steel #4(Hairline) • Rear Corner Panels = Stainless Steel #4(Hairline) • Side Panels = Stainless Steel #4(Hairline) • Front Panels = Stainless Steel #4(Hairline), FALSE CEILING TYPE-CD-41, FLASE CEILING FINISH-Stainless Steel #4(Hairline), VENTILLATION-Cross flow fan, HAND RAILS-Stainless Steel Mirror Finish Handrails on rear car panels, FLOORING-Vinyl Tiles, CAR DOOR FINISH-Stainless Steel #4(Hairline), LANDING DOORS FINISH, Stainless Steel #4(Hairline), FIRE RATED DOORS-Fire rating-60mins , PIT DEPTH-1350, OVERHEAD-4500, HOISTWAY DIMENSIONS (W x D – mm), 1800 mm W x 2100 mm D, CAR DIMENSIONS (W x D x H - mm)- 1650 mm W x 2000 mm D x 2200 mm H, CAR & HOISTWAY DOOR TYPE-Central opening (CO) doors, DOOR OPENING (W x H - mm)-1100 mm W x 2000 mm H, DOOR OPERATOR-DC Door Operator, COP-COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline), CAR POSITION INDICATOR-Monochrome LCD-Blue Background & White font, HALL FIXTURES-O2000, HALL FIXTURE FACE PLATE-Stainless Steel #4(Hairline), HALL BUTTON ARRANGEMENT-Hall Button with HPI, STANDARD FEATURES-Anti-nuisance Car Call Protection, Independent Service (for Duplex only), Overload Device, Nudging, Emergency Firemen’s Service, Emergency Car Light Unit, Infrared Curtain Door Protection, Door Time Protection, Emergency Alarm Button, Extra Door Time of Lobby & Parking, Door Open/Close Button, Manual Rescue Operation, Belt Inspection Drive, Auto Fan Cut OfF, OPTIONS INCLUDED, Automatic Rescue operation.

OUTDOOR UNIT

Outdoor Unit: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .Make - Hitachi / Daikin/ Mitsubishi Heavy

132 HP Outdoor Units

INDOOR UNIT CASSATE TYPE

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fansection with low noise fan/dynamically balanced blower, multi speed motor, coil section with DX Coppercoil, electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, asrequired. The unit shall have automatic force shutdown provision in case off ireon receiving signal from BMS System. The cooling capacity of indoor unit will be at air in let conditions of 27Degree CD Band 19 Degree CWB temperature.

INDOOR UNIT-HIGH WALL TYPE

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic mediapre-filter, fan section with low noise fan/dynamically balanced blower, multi speed motor, coilsection with DX coppercoil, electronice xpansionvalve, outercabinet, cord less remote control, drainpan, necessary accessories etc., suitable for operationon 230V±10%, 50Hz, single phase AC supply, complete as required.The unit shall have automatic force shutdown provision incase of fire on receiving signal from BMS system. The cooling capacity of indoor unit will be at air in let conditions of 27Degree C DB and 19 Degree C WB temperature.

AIR HANDILING UNIT

Supplying, installation, testing and commissioning of factory built floor mountedchilled water double skin typehorizontal/ vertical AHU made of 25 mm thick panels consisting of pre-plasticized galvanized sheet, and inner sheet of plain G.I. casing of thickness 0.8mm both inner & outer layer with with polyurethane foam (PUF) insulation factory injected between them by injection moduling machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling oil section with aluminium finned copper tubes(tubes thickness not less than 0.5mm)cooling coil of 6 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air pre filters, belt drive pakage with TEFC drive motor of efficiency class IE3 suitable for 415+10% volts, 50Hz, 3 phase ac supply suitabley designed for variable frequency drive applications, drain connections, stainless steel(18G) drain pan with PUF insulation, 150mm dia, dial type pressure gauges(2 nos) and industrial type thermometers (2 nos) at the inlet and outlet of coil. Auto purge valve wherever required. Necessary vibration isolation arrangement etc complete as per specificationand of following capacities, etc.

AHU will have UV light to control mold & bacteria, reduce colds & flues germs are not re-circulated by the HVAC system, reduce smell & odors. Also, its Maintain a cleaner coil, improving cooling efficiency and reducing electricity costs and are more effective in humid climates than dry climates. Make : Zeco / Edgetech / VTS

AHU Expansion Kit

Supply & installation of Air Handling Expansion Kit for connection between Air Handling Unit & Outdoor Unit

Supply & Installation of Laminar Air Flow with HEPA Filter

Supply & Installation of Aluminium Extruded bottom loading HEPA Box with bottom operated arrangement, differential pressure measuring points along with Gel Seal Minipleate HEPA filter EU- 13 having Efficiency of 99.97% down to particle size of 0.3 Microns. It can be replaced from room side. Sizes :- 3m x 2m x 2m Make - Spectrum / Equivalent

Laminar Air flow Unit with HEPA Filter

SITC of Copper Piping:-

Supply,Installation,testingandcommissioningincludingvaccumiazationandNitrogentestingoffollowingnominalsizesofsoft/harddrawncopperrefrigerantpipingforVRV/VRFsystem,completewithfittings,withsuitableadjustableringtypehangersupports,jointing/brazingincludingaccessories,insulatedwithXPLEClass-Otubularinsulation/withClass-OclosedcellelastometricnitrilerubbertubularsleevessectionsofspecifiedthicknessasgivenbelowforSuctionandLiquidlines,allaccessoriesasperspecifications etc. as required :

12.7mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

15.86mmdia(OD)(Softdrawn)withtubethickness1.2mmwith19mm thick insulation

19 mmdia(OD)(Harddrawn)withtubethickness1.2mmwith19mm thick insulation

28.58mmdia(OD)(Harddrawn)withtubethickness1.2mmwith19mm thick insulation

31.8mmdia(OD)(Harddrawn)withtubethickness1.62mmwith19mm thick insulation

Cabling Work:-

Supply & Installation of Control wiring for AHU Indoor Unit to Outdoor Unit of 4 Core x 2.5 Sq. mm copper cable with suitable PVC conduit from Outdoor Units to Indoor Units

Drain Piping Work:-

Supply & Installation of PVC drain pipe with Nitrile Rubber insulation along with necessary fittings as required

Ducting

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes , hangers, supports etc as per approved drawings and specifications of following sheet thickeness complete as required.. Duct construction as per SMACNA/ASHRAE/ISHRAE standard provides.

Thickeness 22G (0.80 mm) Sheet

Thickness 24G (0.63 mm) sheet

Insulation

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class"0") insulation on existing duct after applying two coats of cold setting adhesive. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

19 mm thick

Return air riser

Supply & installation of PPGI return air riser with filter (10 micron), Aluminium perforated grille, VCD etc.

Refrigerant

Supply and Commissioning of AHU systems including additional referigernt R410A in all respect to complete the system as per site requirements

Pan type Humidifier

Supply & fixing of Pan type Humidifier with required thermostatic control for OT. Humidifiers made of stainless steel are clad in GPSP/Aluminium sheets and insulated with fibreglass. Units are available in both wall-mounted and floor-mounted designs. Water is heated to 60-70 degrees Celsius in the tank by a warm-up heater, thereby reducing the response time. Water is converted to vapour using tubular heating elements. These elements consists of helical coil of 80% Nickel 20% Chromium alloy resistance wire.

Grilles/Diffusers/Jet Nozzle/ Damper: Supply & Installation of return air grilles/ diffusers as per specifications and drawings.

Linear Grilles

Diffuser (2 Feet x 2 Feet)

Jet Nozzle Diffuser

Volume Control Damper for Air Control

SITC of POE+ Layer 2 Fully Manageable Network Switch consists of Fixed 1RU chassis 24 PoE 1G BaseT, 2 fixed RJ45/SFP+ combo (1G/10G), 2 fixed 1G/10G SFP+ uplink/VFL ports. Internal AC PSU (380 budget), includes country specific power cord, guides and 19" rack mount kit. Inclusive of stacking cable.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper

SITC Gigabit optical transceiver SFP. Supports monomode fiber over 1310nm wavelength nominal) with an LC connector. Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper

6 Port LIU Switch : SITC of 6 Port Loaded LIU with SC Unit for 6 SM fiber Single Mode fibres OS2 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 6 Fiber Capacity & 6 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Legrand/Panduit/RIT/Siemon)

24 Port LIU Switch : SITC of 24 Port Loaded LIU with SC Unit for 24 MM fiber Single Mode fibres SM OS2 (12 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter SM (Make:Legrand/Panduit/RIT/Siemon)

iiiiiiiiiiiiiiii

SITC of Fiber Duplex Patch Cords SC-LC SM Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon)

iiiiiiiiiiiiiiiiii

Supply and laying of 6 core Single mode OS2 Loose tube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. (Make:Legrand/Panduit/RIT/Siemon)

SITC of Fully Loaded 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon)

SITC of Straight LAN Patch Chord-2 Mtr (Make:Legrand/Panduit/RIT/Siemon)

SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon)

Supplying, delivery, installation, testing and commissioning of Flush mounted Cat 6 Information Single Outlet Box.on GI concealed Modular Switch Board including connections and making good the damages caused complete as required & as per Direction of Engineer-In-Charge.(Make:Legrand/Panduit/RIT/Siemon)

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

SITC of Fully Loaded 9U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,16A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; The Front frame should be integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 iPreffered Make-Legrand/Netrack/President/Valrack

Supply, delivery, installation & testing of Modular G.I. box 18 SWG Sheet ISI marked with Modular base & cover for1 or 2 module telephone/Data socket outlet..(Make- Legrand/Panduit/Ortronics)

78 mm X 140 mm X 50 mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preferred Make- AKG/NORPACK/Polycab/Dauphin

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.The Cat6 Cable Should have the follwing specaifications furnished below.

1 Run CAT6 UTP Cable (for Network only . (Make:Legrand/Panduit/RIT/Siemon)

SITC of Telephone Tag Block): IP-65( weather proof). Preferred Make-Krone

20 Pair Krone BOX fully loaded without IPM

Wiring to Telephone Socket Outlet from Junction Box with 0.5 mm2 Four Pair Copper Conductor Telephone Wire run inside prelaid PVC Conduit complete including termination, testing etc complete as required and as per Direction of Engineer-In-Charge. 2 Pair (Make: Polycab/ Finolex/Anchor)

SITC of Single Phase Online 5 KVA UPS Preffered Make-Delta/Numeric/APC/Vertiv

SITC of 65 AH SMF Battery with 24 months Warranty

SITC of MS Battery Rack suitable for 15 to 20 UPS Battery installation

Supply, fitting, fixing, commissioning and testing of 16 Sq. MM Copper Conductor Multi strand PVC Sheilded FRLS Wire with suitable Copper LUGS for Battery Interconnection and suitable 25 Sq. mm copper wire of 2 length of 10 mtrs each for UPS to Battery excluding cable from PANEL to UPS and UPS to panel. Make- Polycab/Havells/KEI

Chemical Earthing

SITC of Corded Digital Deligates Units Gooseneck microphone with programmable switch . With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times , Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Immunity to mobile phone interference Make & Model is: Bosch- CCSD-DL./Harman/Televic

SITC of Corded Digital Chairman Unit Gooseneck microphone with programmable switch With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Chaiman Button;Preferred Makel is :Bosch- CCSD-DL./ Harman/Televic

SITC of of Shielded Twisted Pair CAT-6 Control cable for connectivity complete etc. as required. Preferred Make- Dlink/Crestron/Molex

SITC of 5MP Fixed Lens Network Bullet Camera with following Technical Specifications; Preffered Make: Honeywell/Bosch/Hikvision/Pelco/Sony

SITC of 5MP Fixed Lens Network Dome Camera with following Technical Specifications; Preffered Make: Honeywell/Bosch/Hikvision/Pelco/Sony

SITC of 8 TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD

Supply, Installation, Testing and Commissioning of 55" LED Display Panel, with 4K Resolution : 3840 x 2160, 500 nits (cd/m2) Brightness, contrast ratio : 4000:1, Viewing Angle : 178° h/v, response time : 8ms, Display Colors- 16.7 Mill; Built in Speaker-10W+10W ; Inputs : HDMI x 2, DVI‐D, DisplayPort, Audio, RS‐232 Control, 100‐240 VAC @ 50/60Hz Power Supply, 24x7 Operation.; Preferred Make LG/Samsung/Panasonic

BOREWELL

Cost of drilling 200mm X 165mm X 125mm deep bore well in all kinds of soil and rock in rural area for installation of pump set withhydraulic DTH rig machine , all complete including supplying all materials , tools , drilling rig , air compresser and equipments, as well as fuel , lubricants and cost of transportation of rig machine and other vehical up to the site up to the site ( basic rates ) . (ADD 14.95% ON BASIC RATE FOR C.P.+O.H)

(a) From 0.00 M to 50.00 M below G.L

(b) From 51.00 M to 125.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

200mm Nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump ste shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run shall be provided with each pump.

Submersible pump set 150mm dia (with polypropylene/ Noryl Impeller)

2 HP (ADD 14.95% ON BASIC RATE FOR C.P.+O.H)

D.O.L starter with SS Enclosure with 380/415 volt coil 5 to 10 H.P. (ADD 14.95% ON BASIC RATE FOR C.P.+O.H)

Supplying ,fitting & fixing & connecting 3 core 4 sqmm flat copper submerssible cable of Finolex / Hevels make including all taxes ,royalty etc all complete job as per direction of E/I (ADD 14.95% ON BASIC RATE FOR C.P.+O.H)

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I

Geophysical survey

Providing and Fixing backdrop panneling 150mm thick size as per drawing , made in hard wood frame(mirandi wood) 50mm x 50mm thick & c/c 600mm maximun both ways joint rigidly horizontally & vertically with nails, screws etc. fixed to wall/ceiling & columns with wooden plugs. 11 mm thick MDF Board is to be fixed on top of frame with 10x8 mm deep grooves on both sides of the center panel. 11mm MDF Board is to finished with laminate on both side of approved design and all groves to be finished with laminate shade. Center panel is of 19mm MDF jali /Engg. stone cladding of aprooved design and of size: The visible part through MDF Jali is to be finished with lacqured glass of approved design. All work is to be carried out as per drawing and instructions of engineer in charge. ( MDF Board/ MDF Jali & Laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent)

P/Fixing Wall paper as per approved brand and manufacture to give an even shade and color as approved by architect. & instructionof Engineer in charge.

Providing And Fixing Full Height Ms Racks Of Load Capacity 100-150 Kg Per Rack And Total 6 Level Per Rack Of Length 2m , Width 0.6m, And Height 2.4m, Thickness 1.6mm, Complete In All Respect As Per Design And Instruction Of Engineer In Charge

Providing and Fixing of full ht. wardrobe depth 600mm of durable CRCA steel make with 2 door openable assemblymounted on floor, 1no. of drawer inside with self closing bright finished CP hinges,inside and outside enamel paint finish on metal surface and of approved color and shade .The body is of alloy steel make with lock arrangement, no of shelves is 3 of brand godrej interio/durial/nilkamal or similar make as per the direction of engineer in charge

Providing & Fixing Translucent Roller Blinds Over Window Opening With Arrangement Of Closing & Opening With G - String, Complete In All Respects As Per Design And Instruction Of Engineer In Charge. (Make Vista / Mac Or Equivalent,Fabric Model No. Equivalent To Echo (Vista) / Abstract /Silky/ Ribcord/Drizzle/Trans)

Providing and Fixing Furniture Atelier/Godrej/Durian or equivalent/Godrej/Durian or equivalent Make Panel table Linea 2400 x 750 :- Top shall be of 36 mm thick prelaminated particle board with 2mm thick PVC edge banding finish with as per approved laminate color. GABLE ENDS :- shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge banding finish with as per approved laminate color. MODESTY:- shall be of 18mm thick prelaminated particle board with 2mm thick PVC edge banding finish with as per approved laminate color.

Providing and Fixing Furniture Atelier/Godrej/Durian or equivalent Make chair upholstered with Leatherite . The seat and back are made up of 1.2cm thick hot pressed plywood upholstered with leatherite and moulded Polyurethane foam. The back foam is designed with contoured lumber support for extra comfort. BACK SIZE: 520 mm (W) x 730 mm(H). SEAT SIZE: 550mm(W) x 520mm(D). Overall Height of chair is 1180mm .The seat and back are Joined together. The armrest assembly comprises of Chrome Plated Contoured frame which is connected and bolted to both seat and back . The armrest top is cushioned with foam which is upholstered with matching Leatherite. The chair has TORSION BAR TILT MECHANISM.

Recepetion Table Size:- 3000x750x1050 mm :- TOP & Gable End : 25mm thick PLPB board with 2mm thick PVCedge banding finish with as per approved laminate color. Rest All :-18 Mm thick PLPB board with 2mm thick PVCedge banding.Finish with as per approved laminate .

Conference Room Table Size:- 8000x750x1050 mm :- TOP & Gable End : 25mm thick PLPB board with 2mm thick PVCedge banding finish with as per approved laminate color. Rest All :-18 Mm thick PLPB board with 2mm thick PVCedge banding.Finish with as per approved laminate. With openings for mic, switch and socket (hidden type) etc as per directions of engineer in charge

Conference Room Table Size:- 2000x750x1050 mm :- TOP & Gable End : 25mm thick PLPB board with 2mm thick PVCedge banding finish with as per approved laminate color. Rest All :-18 Mm thick PLPB board with 2mm thick PVCedge banding.Finish with as per approved laminate. With openings for mic, switch and socket (hidden type) etc as per directions of engineer in charge

Providing and placing ergonomical, comfortable and aesthetically design medium Back chair. The seat size shall be 485mm (W) x 460mm (D), The back height shall be mm 560mm and overall height- 1000mm . The seat shall be made of hot pressed 15mm thick moulded ply and upholstered with Urethane foam Foam density 40kg/m3 & net fabric tapestry. The Back is made of polyproplene outer side and upholstered with nett or breathable mesh with cushioned support. The armrests are made of polyproplene and mechanism shall be center tilt with single point locking. The pneumatic height adjustment shall have an adjustment of 63mm in BIFMA Standard class 4.Pedestal is made of injection moulded black nylon fitted with 5 nos. twin wheels castors which are made of injection moulded black nylon 30% glass filled and nylon base is load tested capacity -1150 kg in BIFMA standard.

Providing and Fixing Furniture Atelier/Godrej/Durian or equivalent Make Supplying and placing of approved make 3 seater Sofa with 2 end armrest complete as per specifications . upholstered in fabric and should be in compliance with the following specifications. Seat, backrest and armrests - padded with polyurethane foam and upholstered in beige and/or light grey woven fabric. Frame of sofas made of durable wood and the base of seat and backrest equipped with metal Z- shape springs. Legs - 60mm dia. steel tube in black polyurethane finish with black plastic shoe.

Providing and fixing classroom desk and chair combo of 125mm thick prelaminated particle board with 2mm thick PVC edge banding supported on 25mm thick PLT Gable ends along with 18mm thick PLT modesty Panel. With 18mm PLB Hanging drawer unit provided with suitable handles nad locking mechanism as per the direction of Engineer In charge.

Providing and fixing Signage at Canopy with Backlit LED Letters Acrylic Letter fixed on MS Frame - 20 Feet by 1.5 Feet

Epson EHTW-750 Projector + RNT Projection Screen Motorised 100 Inches - 16:9 Ratio + Projector Mount + JBL Bar 2.1 Deep Bass Soundbar(Bundle Pack)

HP/DELL/ACER COMPUTER SET: Type: All in one Processor: AMD Ryzen 5 5250U (2.6 GHz base clock, up to 3.5 GHz max boost clock, 4 MB L3 cache, 2 cores) Memory: 8 GB DDR4-2400 SDRAM (1 x 8 GB); Storage: 512 GB SSD storage; 1TB HDD storage Display: 23.8 diagonal FHD (1920 x 1080), IPS, three-sided micro-edge, anti-glare, 250 nits, 72% NTSC Operating System: Microsoft Windows 10 - Home edition; Microsoft Office 2019 - Home and Student Edition with UPS, Keyboard and mouse complete

CANON/ EPSON/HP PRINTER: Printer Type - Ink Tank; Functionality - All-in-One (Print, Scan, Copy) , Scanner type - Flatbed; Printer Output - Colour Connectivity - Wi-Fi, USB, App Pages per minute - 33 pages (Black & White), 15 pages (Colour) ; Cost per page - 7 paise (Black & White), 18 paise (Colour) - As per ISO standards Ideal usage - Home and Small office, Regular / Heavy usage (more than 300 pages per month) Page size supported - A4, A5, A6, B5, C6, DL ; Duplex Print - Manual ; Print resolution - 5760 x 1440 Compatible Ink Bottle - T003 (Black), T003 (Cyan), T003 (Magenta), T003 (Yellow) ; Page Yield - 4500 pages (Black & White), 7500 pages (Colour) ; Comes with 4 original Epson Ink Bottle (one of each colour - Bk, C, M, Y) inside the box Warranty - 1 year or 30,000 pages whichever is earlier on?site warranty from the date of purchase

XEROX MACHINE LaserJet Professional MFP Printer Printing TechnologyLaser Brand:HP/XEROX/KONICA Recommended Uses For ProductOffice ColourWhite Print mediaEnvelopes, Paper (plain), Transparencies Scanner TypeSheetfed Wattage760 Watts Operating SystemWindows Hardware InterfaceUSB 2.0 Control MethodTouch

NOTICE BOARD Material Softboard Core, Alloy Aluminium (6063-T6) Frame, Premium Flocked Fabric (Velvet) Cloth Surface& Virgin ABS CornersSoftboard Core, Alloy Aluminium (6063-T6) Frame, Premium Flocked Fabric (Velvet) Cloth Surface& Virgin ABS Corners See more ColourGreen Size3 X5 ft

CEMENT(3 Km radius)

SAND(25 Km radius)

Bricks(18 Km radius)

AGGREGATE(25 KM )

Add GST 18 %

Add Labour cess 1%

ASHISH RANJAN (BID ID -640617)