SPECIAL REPAIRS TO BLDG No P 23 AND BOUNDRAY WALL UNDER GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcand removal of entire debris as ordered outside MD land complete all as directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chaj-jas and similar sus-pended work (reinforcement cut as required to facilitate demolition) including removing of debris as ordered outside MD land complete all as directed.

Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed.

Dismantling of post or struts (wood, steel or RCC) any section, including taking out embedded portion in concrete and making good the disturbed ground complete.

Dismantling structural steel work incl gates, doors but excluding framed truss etc complete all as directed.

Dismantling of plain or corrugated steel sheeting any gauge thickness incl Nanital or similar pattern as in roof coverings and stacking at site where directed .

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 9 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Surface excavation averaging 15cm deep and n.exc 30cm deep and getting out in soft/loose soil complete all as specified and directed

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out in soft/ loose soil and removing surplus soil outside MD land complete all as directed.

Excavation in trenches and not exe. 1.5 m wide and not exe. 1.5 m in depth for foundation of drain, man hole etc. not exe. 10 Sq. m on plan and not exe. 1.5 m depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft rock complete all as specified and directed

Removing excavated surplus soil to a distance not exceeding 50 mts and depositing where directed .at a level not exceeding 1.5 M above the starting point complete all as directed.

M & L for Hard core of broken hard stone or boulders of guage not exceeding 63 mm , deposited spread as subbase to inter locking tiles in layers n.exc 15cm thick , watered & well rammed to true surface complete all as specified and directed.

M & L for PCC 1:4:8, type D2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

M & L for PCC 1:3:6, type C2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:4 complete all as specified.

All same as per item No 19 here-in-above but solid blocks not exceeding 10 cm thick -do-

Providing precast ce- ment concrete Type B1 1:2 :4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts , boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 complete all as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed

.M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

.M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

Cutting holes of size Exc. half brick but not exc. one brick in brick walls in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required including making good as per its original specification with out any extra cost complete all as directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 as required including making good as per its original specification with out any extra cost complete all as directed.

M & L for random and polygonal rubble walling excluding bond / through stones , pitching laid dry hand packed tightly complete all as specified

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished of concrete flat complete all as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L for 2nd class hard wood Plain fillets bull nosed type of size exc 3 sq.cm not exc 6 sqcm, Square, rectangular or triangular in section, clean sawn, secured with nails or brads

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications complete all as directed.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness including filling the hollow section of steel frame with PCC 1:2;4 type Bo using 12.5 mm graded crushed stone aggregrate to the entire hollow section to the satisfaction of Engineer-in-charge , complete as specified & as directed.

S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames , wrought, framed, rebated on the solid, rounded or chamfered , put together with glue, pinned at joints and fixed in position complete all as directed.

S&F 35 mm thick second class hard wood factory made plain framed panelled door shutter ( two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12mm thick veneered particle boards with commercial veneering on both face the size of rail and style as per IS - 1003 (Part I) kiln seasoned and chemically pressure treated and fixed to chowkats complete all as directed.

S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F 6mm thick MDF Board one side finished as in wardrobe no of compartments & Drawers all as specified and as directed by Engineer-in-Charge.

S&F 19mm thick MDF Board both side finished as in wardrobe no of compartments & Drawers all as specified and as directed by Engineer-in-Charge.

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F100 mm size butt hinges, medium weight stainless steel and fixed .

S&F 100 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F Mild steel powder coated body door stopper with hard drawn steel spring, 150mm size fixed to door all as directed.

S & F mild steel 300mm ordinary rat rail rod pattern spring including roller and roller plate fixed to door all as directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 40mm (when open) fixed with CP steel screws complete all as specified and as directed.

S&F in repair 25mm dia aluminium anodised decorative type curtain rods. fixed with CP steel screws complete all as specified and as directed.

S&F in repair decorative type curtain rod brackets.

S&F in Repairs Tubular Towel Rail of 20mm dia of 60cm in length, D shaped, with brass chromium plated brackets all as specified and directed.

Supply only stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples for steel window .

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as directed.

S & F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No. 53 here- in – above but 5 mm dia and over upto 10 mm dia as in stirrups - do -

S&F Mild steel iron framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fit-tings (exclusive of steel sheeting or other cover-ing, running rails and guides) and hanging; al-so fastening and fixing complete all as directed . Steel conforming to Fe 410 -W (Gde E- 250 Quality A)

S&F galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc as directed. Make : M/s Sachin , TATA or any approved make as approved.. Note :- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment

Supply only MS galvanized chain link fencing (120 to 140 gms) 4mm dia and weighing not less than 3.5 kg/sqm diagonally pinned including line wire rails, straining bolts and provision of binding wire complete all as specified and as directed. Make : M/s Sachin , TATA or any approved make as approved..

Fixing only diagonally pinned fencing wire including line wire, any mesh size and type of standards, rails, straining bolts etc. including provision of binding wire complete all as directed.

S&F mild steel work in hard rails , winds ties post and structs in fencing screwed or welded to shaped as directed , including all necessary drilling ,bolting or welding etc, and similar work confroming Fe-290 Gde-E-165.

S & F 5 feet long pulley operated clothes drying system kit of 4 pipes consisting of aluminium pipes each of outer dia 22mm and inner dia 19.8mm, pulleys made up of derlin with rope guide mounted on channel pair of length 24" (distance between two pipes is adjustable). Locking system to hide rope knot. Channel to be mounted or fixed with self tapping screws provided in kit. Rope will HDPE double core of 4mm dia complete all as dired.

S&F Box type Steel Windows/Ventilators double side shutters (Windows side hung type , Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm , windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars/grill welded with steel frame (100c/c horizontically) all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bard/Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges,Telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only 4 mm thick sheet glass and stainless steel wire mesh be measured and paid separately. (iii) Weight of Grill/Guard Bars, handle,hinges and locking arrangements shall not be accounted for payment purpose . (Note : All Windows/Vent design as per CECZ TD drg No 539)

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing the same with neat cement slurry with 3.0 Kg of cement per Sqm complete all as directed.

Material and labour cleaning of surface with wire brushes and water removing of unsolvent materials and depositing of the same as directed outside MoD land and provide 10 mm thick screed bed/ bedding layer in CM 1:3 mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on RCC roof/ parapet once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.30 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cm end lap torch sealed and bonded as per detailed procedure as directed and finally finished the top surface with two coats of thermal resistant paint complete all as specified and as directed. Note: (i) The quoted rate is deemed to be inclusive cleaning the entire surface to satisfaction of Enginner-in-charge & removal of debris , 10 mm thick 1:3 screed & complete APP treatment. (ii) WPC will be paid seperately (iii) The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface.

M&L 25 mm thick cement concrete type B-0 (12.5mm graded stone aggregate) as in RCC roof / Floor surface with mixing of water proofing compound 2% by the weight cement to horizontal or vertical surfaces finished cement concrete surface even and smooth including necessary form work & finally the surface is completly dried apply Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat for sunken floor treatment all as specified and directed. (Note : (i) Water proofing compound will be measured separately (ii) Quoted rate is deemed to be inclusive of bitumen two coats)

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in padding over roof / chajja finished even & smooth without using extra cement complete all as directed.

M & L for 25 mm thick plain cement concrete 1:2:4 type Bo using 12.5 mm graded crushed stone aggregate as in sub base of floor and finished the surface complete all as directed.

M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of floor/ foot path etc and finished the surface complete all as directed.

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

All same as per item No 70 here - in - above but each tile exceeding 0.18 Sqm but not exceeding 0.36Sqm -do-

All same as per item No 70 here - in - above but as in dado & skirting with 10 mm thick 1 : 4 cement mortar screed - do -(Note for item No 70 to 72 : i) Quoted rate is deemed to be inclusive of cement screed.)

M&L glazed ceramic coloured tiles of size 350mm x 250mmx 7mm / 450mmx350mmx7mm thick, on verticals surfaces, set and jointed inneat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 43 to 46 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Colour of tiles shall be got appproved before incorporation in the work)

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over and including 15 mm thick screed bedding in cement mortar 1 : 4including Rounding to edges complete.

All same as per item No 74 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 74 & 75 : i) Quoted rate is deemed to be inclusive of cement screed.)

M&L M-35 grade, 60 mm thick machine pressed, PVC moulded precast cement concrete interlocking paver blocks any shape and size with grey cement and pigment confirming to IS: 15658-2006, laid over and including 50 mm thick compacted sand cushion complete complete all as specified.(Note ; Quoted rate is deemed to be inclusive of 50 mm thick compacted sand cushoning).

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

All as per item No 77 here-in-above but 5mm thick in CM 1:3 on ceiling,chajja,roof projection etc.

M & L for Dubbing out average 10mm thick on irregular face of stone walls of external surface in CM 1:6 complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work/ stone work or concrete surfaces mixed with WPC as per manufacturer instruction, and finished the surface fair and even complete all as specified and directed.

All same as per item No 80 here-in-above but in cement moartir 1:3 -do- (Note for item No 80 & 81 : WPC shall be measured and paid separately).

Racking out joints / points in cement mortar to random rubble or polygonal rubble uncoursed or brought upto coursesin cement or cement lime mortar complete all as directed.

Three coats of white wash on newly plastered surface of ceiling after necessary preparation of surface complete all as directed.

All as per item No. 83 here-in-above but two coats as in ceiling - do -

M&L preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as directed.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Complete removal of any type of exixting treatment from walls surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Complete removal of any type of exixting treatment from walls surfaces & applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces complete all as specified.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

Supply only sheet glass 4mm thick ordinary quality and glazing with oil putty in square exc. 0.5 sqm in each pane complete all as directed.

S&F sheet glass 4mm thick figured glass, pin headed type and glazing with oil putty not exceeding 0.5 Sqm in each pane complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface not exceeding 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

Taking up or down steel tubing for 15mm dia pipe and connections including cleaning for re-fixing or removal to store.all as directed .

Taking up or down steel tubing for 20mm dia pipe and connections including cleaning for re-fixing or removal to store.all as directed.

S&F 16 mm outer dia CPVC Pipe (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete ass as specified.

S&F 20mm outer dia CPVC Pipe (ISI Marked) fixed complete to wall, celing or floors including taking up or down 15mm bore steel tubing complete all as specified.

S&F in repairs 15 mm bore CP bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule

Supply and fixing in repair Angle valve cast copper alloy cromium Plated (CP) 15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as directed.

S&F soap dish, vitreous china, white, approximate size 160x160x90mm fixed to plugs with chromium plated (CP) brass screws

Supply and fixing in repair PVC Shower Rose swivel type suitable for 15mm dial pipe (as per sample approved by Engineer-in-Charge complete all as directed.

S&F Gun metal gate or gate valves with iron wheel head screwed box and both ends for iron pipe for 20 mm bore of pipe or union complete all as directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repars complete all as directed.

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repars complete all as directed.

S&F in repair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S & F 75 mm bore size PVC (SWR) bends any radius with access door including jointing the same with solvent cement complete all as directed.

S & F 110 mm bore size PVC (SWR) bends any radius with access door including jointing the same with solvent cement complete all as directed.

S&F 110 mm bore size PVC (SWR) junction single(single T) equal or unequal with access door including jointing the same with solvent cement complete all as directed.

All as per item No 109 here -in -above but 75mm bore.

S&F PVC (SWR) Vent cowl 110 mm bore size fixed complete all as directed.

M & L for 150x100mm gully traps, square or round mouthed, type 'P'/S

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

M & L for Cutting into existing manhole for connecting 150 mm bore(internal dia ) new drain pipe , making good to pipe and rendering , cuttingout existing benching for forming branch channel ( 1/ 2 round or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded granite stone aggregrate , smooth finished and reforming benching as required complete all as specified and directed.

E&M : Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing taken down materials to a place where ordered for crediting including making good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed..

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) on Surface conduite conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bell point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5 Amp on independent board

(c) One 3 pin socket point 5 Amp on same board with other switches.(to be provide new point as ordered at site)

All as per item No. 120 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-One light point controlled by 2 way switches 5 Amps

Supply and fix Switch piano, flush button single pole, 5 Amps one way.

Supply and fix Switch piano, flush button single pole, 16 Amps two way.

Supply and fix Switch sokcet combination flush type 5 Amp , 2-in-1 muliti purpose

Supply and fix Switch socket combination flush type 5/16 Amps , 5-in-1 universal multipurpose

Supply and fix bell push, flush button single pole, 5 Amps one way.

Supply and fix bell ding dong , 230 V AC single pole,, 5 Amps one way.

Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks.

Supply and fix Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan.

Taking down existing light fittings fixed in any description and S&F new 10 Watt , 6000K, 230 Volt, 2ft Batten surface and wall mounted LED batten with polycarbonate housing with PVC housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. . Make : Havells/wipro/surya/ Philips

Taking down existing light fittings fixed in any description and S&F new 20 Watt , 6000K, 230 Volt, 4ft Batten surface and wall mounted LED batten with polycarbonate housing with PVC housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. . Make : Havells/wipro/surya/ Philips

S&F bldg security light light fittings 1x 35 Watt Ac 230v out door type LED street light with high pressure die cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistent including thermal managment in multiple optics complete , IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. Make : Crompton Greaves/Bajaj/ Philips

S&F steet light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flat iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply, fabrication, installation and testing of LT out door type factory made(CPRI Approved ), junction box of size 900mm(H)X700mm(B)X400mm(W) (over all dimension ) made out of 3.15mm thick CRCA sheet dully supported with mild steel angle iron of size 40X40X5 mm frame, 04 Nos aluminium bus bar of of capacity 250 Amps with drilled hole for incoming/outgoing cable connection with necessary alumiium lungs, GI nuts bolts and washer including 08 Nos bridge insulator DMC , heavy duty, suitable for 3 Phase 4 wire system, one danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled white with letters, figures and conventional skull & bones in signal red colour and fixed in front door size and PCC (1:3:6) type C-2 foundation 0.30m above normal ground level & 0.30m below ground level with necessary exacavation and earth work and painting to internal and external steel surface with powder coated (Siemence gray) RL-35 after neccesary preparation of surfaces including Indicating lamp LED type 240V 50 Hz AC -one set of 3 Make: L&T/Havells/HPL compete all as directed.include (a) One Incoming MCCB 4Pole 100 Amps, reperuig capacity 25 KA

S&F in repair Sheet metal enclosure (ISI marked) for energy meter box,01 mtre x 01 mtresize 3 mm Thick with fixing arrangment to 12 nos single phase energy meter and 415 volts TPN 04 way Vertical type, double door,DB- 01 to be fix same orginal possition, painting to internal and external steel surface with powder coated (Siemence gray) and tested on completion complete all as directed.

S&F in repair Sheet metal enclosure (ISI marked) distribution board for 415 volts, TPN 04 way Vertical type, double door, triple pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S&F in repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SP 8 way Horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S&F in repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SP 4 way Horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S & F in repair MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB complete all as specified and directed by Engr-in-charge.

S & F in repair MCB single pole & neutral 40 Amps 240 volts, 10 kA rupturing capacity providing in DB complete all as specified.

S & F in repair Isolator four pole 63 Amps ,415 Volts , 25 kA rupturing capacity providing in DB complete all as specified.

Taking down old existing sub main wiring and provide new submain wiring with 2 runs of 2.5 Sqmm single core PVC insulated, unsheathed, multi stranded copper conductor and one single core 2.5 Sqmm PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit/casing caping of size as ordered in walls / ceilings etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 2.5 Sqmm cable , one run 2.5 Sqmm cable and one run of PVC Conduit /Casing caping shall be measured as one unit length) .

All as per item No 145 here-in-above but 2 runs with 4 Sqmm single core cable and 4 Sqmm single core as earth contunity wire -do- . (Note :- 2 runs 4 Sqmm cable , one run 4 Sqmm cable and one run of PVC Conduit/Casing caping shall be measured as one unit length)

Supply & fixing and testing exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, metalic body , suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in any type of masonry wall to size by core cutting using core cutting machine & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan finally making good the disturbued surface of walls both internal & external to its original specifications to the satisfaction of Enginner-in-charge complete all as directed. Make : Bajaj/ CG / Orient / Usha as approved (Note : Quoted rate is deemed to be inclusive of core cutting to wall , including finishing the wall surface to its original specifications)

S & F ceiling fans complete with blades, down rods,electronic regulator and accessaries 230v,1200mm sweep, Min air delivery 210 CFM with service Value 6.00 BEE Five star rated with Brushless direct current motor (BLDC) Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire as complete all as directed

M & L for Earthing complete with galvanized steel earth plate electrode 600x600x6. mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth Strip 25x4 mm as earthing lead of bolts,nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion including dismantling of old earthing materials.

M AND V ENTERPRISES

Kavitha Constructions

M/s Sri Chakrapani Constructions

Aavani BUILDERS AND CONTRACTORS

PRACHANIVA CONSTRUCTIONS