SPL REP REPLACEMENT OF TOILET BLOCK BATHROOM AND DISPOSAL FACILITY IN BLDG NO P38 AND P39 (OR LIVING LINE) AT 1 (I) R AND O FLT AND SPL REP TO BLDG NO P87 (OTM) OF 1 BIHAR AT KHOJATOLI POCKET OF RANCHI MIL STN

Amount

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specially provided for

M&L for PCC type E2, 1:5:10 (using 40mm graded stone agg) as in foundation, filling and mass concrete.

M & L for RCC (1:2:4) type B-1using 20 mm graded stone aggregate as in slab supported on wall ,Chajjas,deck slab Shelves/tank staging etc.

Use & waste frame work to sides and soffits of floor or roof slab, chajjas not exc 200 mm thick (Horizontal or sloping) rough finished complete.

M & L Mild steel bars 10mm dia TMT Bars and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of brick wk masonry built in cement mortar incldg all quoins arches pillars etc

M&L brick work with sub class ‘B’ old sized bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6

M&L Brick work with sub class 'B' Brick straight or curved on plain to any radius in half brick thick wall built in cm 1:4

Dismantling floor, hearth or wall tiling includiing cemenet mortar bedding, removing serviceable tiles to store and rubbish off the premises

M&L screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 for fixing tiles.

M&L Non skid ceramic joint free coloured tiles 7-8 mm thick (square or rectangular) area of each tile exc 0.11 SM but not exc 0.18 SM in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement. to match as in floors.

M&L screed bed or bedding layer of mortar 10 mm thick in CM 1:4 as backing coat for laying tiles in dado , on brick or concrete surfaces

M&L for glazed ceramic coloured tiles in vertical surfaces 350 X 250X 7/ 450x350x7mm thk set and jonnted in cement slurry and pointed in white or colour cement to match complete.

M&L Granite 18 to 20 mm thick (of any type )work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed

M&L for broken stone hardcore of gauge n exc. 63mm, deposited, spread and levelled in layer n exc. 15cm thick, watered and rammed to a true surface complete.

M&L for 75mm thick PCC type C2 1:3:6 (using 40mm graded stone agg) as in plinth protection/Path/floor finishing surface of concrete topping even and fair without using extra cement complete.

Taking down cement plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbinng down with water, etc.

M&L rendering 10mm thick in CM 1:6 on fair faces of brick work , finished even and smooth without using extra cement.

M&L rendering 15mm thick in CM 1:4 on fair faces of brick work , finished even and smooth without using extra cement.

M & L preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete.

M & L preparation of complete removal of existing treatement from old plastered surface of wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisteance as per IS 15489:2004, Alkali & Fungal resistance, dirt resistance exterior paint of required shade ( Company Depot tinted) with silicon additives @ 1.43 litre /10 sqm over and including priming coat of exterior primer appplied @ 0.90 litre /10sqm over a coat of wall putty on new plastered wall surfaces incl preparation.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisteance as per IS 15489:2004, Alkali & Fungal resistance, dirt resistance exterior paint of required shade ( Company Depot tinted) with silicon additives @ 1.43 litre /10 sqm over and including priming coat of exterior primer appplied @ 0.90 litre /10sqm over a coat of wall putty on old wall surfaces incl complete removal of existing treatment.

Taking down existing chowkats or frames, without taking out shutters from the frame, n exc 1.5 Sqm

Taking down existing chowkats or frames , without taking out shutters, from the frame, exc 1.5 Sqm but not exc 4 Sqm each,

S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete as per manufacturer’s specification and drawing.

S&F factory made solid panel PVC door shutter 30mm thick(style) consisting of frame made out of mild steel tubes for top & bottom rails, Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm with steel inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, fixing in the frame at site as per specification, drawing .

S&F 100 mm size butt hinges of medium weight cold rolled mild steel

S&F steel alloy handles, fabricated type, size of handle 125 mm,

S&F extruded steel alloy handles, fabricated type, size of handle 150 mm,

S&F steel alloy 200mm long barrel tower bolts of extruded section,

M/L Steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dove tailed or welded (including two nos tower bolts 125mm in each leaf and one nos MS flate iron 25x 3mm handle in each leaf.

Description all as per ser item No 32 above item No, but without glazing bars complete all as specified and directed including sash bars for fixing wire mesh.

S&F Steel ventilator in repair with top hung shutter including hinges steel peg stay, complete all as specified.

S&F in repair aluminium anodised tubular towel rail 20mm dia D Type, 60 cm long between flanges complete all as directed

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 in brick walls for concealed water tubing, cutting not exc 10cm girth

Taking up or down 15mm dia steel tubing and connection including cleaning for re-fixing or removal from site.

S & F, 15mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors.

Taking up or down 20mm dia steel tubing and connection including cleaning for re-fixing or removal from site .

S & F, 20mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors,.

S&F framed work such as grills, gratings etc. With ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming Fe 290, Gde -E -165

M&L in repair for 75mm dia PVC (SWR) trap , plain with grating including jointing with solvent cement.

S&F in repairs PVC valve less,low level flushing cistern ,10 ltr capacity, white symphonic action with inlet, ball valve, float and handle including 32mm PVC flushpipe and brackets

S&F in repair 15mm dia bib taps,cast copper alloy chromium plated fancy type with crutch or butter fly and screwed for iron pipe or for brass ferrule and fixed.

S&F in repair brass chromium plated wall mixer with 'hot and cold' arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC.

S&F in repair brass chromium plated Basin mixer with 'hot and cold' arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC.

S&F in repairs stop valves fancy type of 15 mm dia chromium plated long shank and cup (concealed type) screwed both ends for iron pipes or for unions.

S&F PVC connection 450mm long with two brass end complete all as specified

S&F in repairs Brass Chromium plated shower rose with swivel joints, 125 mm size, including fixing to stel pipe or union

S&F PVC (SWR) 110mm bore dia pipes single socketed, in any length with rubber ring joints, fixed to walls including taking out old PVC unserviceable pipes complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends with access door

S&F PVC (SWR) 110mm bore junction single, (Single T) equal or unequal

S&F PVC (SWR) bends 110mm bore

S&F PVC (SWR) vent cowl 110mm bore

S&F PVC (SWR) 75mm bore dia pipes single socketed, in any length with rubber ring joints, fixed to walls including taking out old PVC unserviceable pipes complete.

PVC (SWR) bends 75mm bore

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty/ glazing pins/spring clips in square n exc. 0.5 sq. m in each pane

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane

M&L for Stainless Steel wire cloth for 0.56 mm nominal dia of wire & average width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples etc

M&L for preparation of new steel surafces of any description not otherwise described, over 10 cm width or girth, priming with a coat of red oxide primer and applyinng 2 coats of synthetic enamel paint of approved shade all as specified and directeed by EIC

Supply & fixed in repairs Vitreous china white wash hand basin counter sunk of size 550x400mm, with and incl necessary fittings.

S&F in repair vitreous china squating pan 'ORRISA' pattern, size 580X450mm white with integral foot rest complete including connection to trap and to antisyphonage pipe etc complete including making good to floor.

S&F in repairs Vitreous China bowl urinal half stall type, white with grating and union for discharge pipe type complete including providing and fixing plugs complete.

S&F 32 mm dia waste/flush pipe for urinal and WHB complete.

Dismantling water tanks Capacity in Exc 500 & n exc 1000 litres and removing to store

S & F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) Capacity in 1000 litres hoisted and fixed in position all as specified in SSR Part I.

S&F 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule

S&F Gun metal globe or Gate valves 20 mm bore with iron wheel head, screwed both ends for iron pipe or for pipe or for unions and fixed.

M&L for PCC type C2 1:3:6 (using 40mm graded stone agg) as in surface channels, drains and similar works etc .

M&L extra for forming fair finishing to drain or channel, 30 cm inner girth in cement concrete, with using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed

M&L Providing, cement concrete type B1 1:2:4 (20 mm graded aggreate) in filling of pressed steel frame, coping, fixing of hold fast and water troughs and the like including weathering etc similar work complete.

Dismantling wrought iron or mild steel work of any description not otherwise provided

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

S/F in repair Bed side built -in steel loker of following specification as per drawing No FD 1029. All MS sheet shall be of 0.9 mm thick. All Joints, welding and fixing shall be done in accordance with standard workmanship. Two legs shall be provided to locker as shown on drawing and shall be of 0.9 mm thick MS sheet. Sheet shall be hot rolled carbon steel sheet as per IS 1079:2009 or cold reduced low carbon steel sheet as per IS 513: 2008 . The sheet shall be of any designation or grade as per the relevant Indian Standard. All joints, welding & fixing shall be done in accordance with the standard workmanship and specification shown in drawing. A Three way bolting device controlled by a brass lock and operated by a chromium plated metallic S-Type handle - 01 No. shall be provided (as per sample approved by GE/Engr-in-charge to shutters of Locker. A curtain rod of stainless steel shall be provided to Locker and 04 Nos Plinth screw (Plastic inserted molded screw) shall be provided in legs of Locker. The overall weight of Locker bed side steel after painting shall be not less than 45 Kg of each locker. All steel surface internally and externally shall be given two coat of metallic synthetic enamel paint over a coat of primer (spray painting). The colour shade of painting in dual shade shall be as approved by GE. Rest all as per drawing ( FD 1029).

Hacking out old boken glass(any thickness, size, quality or description) from wooden frames/steel frames glazed with oil putty or fixed with beads complete.

S& F in repar 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n. Exc 0.5 Sqm in each pane.

S&F in repair 18/19 mm thick pre-laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shutter, shelf, etc complete

S&F factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber,frame (88mm x 52mm),sliding sash (42mm x 67mm),sliding interlock (one vertical length in each shutter)(45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water ets, making arrangement for fixing of hardware, EPDM gasket. 1.2 +- 0.2mm thick galvanized steel frame (30mm x 18mm) 2 nos,sliding sash (30mm x 18mm) 2nos,sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100m long fastener. Hardware (touch lock of zinc alloyed (white powder coated),steel roller system,stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate excludes cost of glass and includes all oyher connected accessories) area n.exc.2.00 sqm each fixed from ground floor to height of 12 floors

S&F 7 mm thick aluminium grills of make "Decogrill" model DG 104 surrounded by aluminum 'C' channel and size of opening 75x75 mm all as specified and directed fixed from ground floor to height of 12 floors

S/F 4.80mm thick sheet glass ordinary quality and glazing with oil putty in square nexc 0.5 sqm in each pane

S&F 4.8mm thick tinted glass ordinary quality and glazing with rubber gasket in squares exceeding 0.50 sqm in each pane

M&L machine cut kota stone slab flooring 18-20mm thick over & including 20mm screed base in CM 1: 4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

S&F 2nd class hardwood plain fillets, square, rectangular or rectangular in section, clean sawn secured with nails sectional area exc 13 & n exc 25 Sqcm complete.

S&F in repairs15mm dia swan neck pillar tap cost copper alloy fancy type with capstan heads chromium plated screwed down high pressure with long screwed shanks & fly nuts screwed for iron pipe etc complete all as specified and directed

M&L marble work of any shade 16 to 18mm thick in cooking platform, steps, windowcills, etc over and incl 15mm thick cement screed base in CM 1:4 laid and jointed with white cement slurry mixed with admixture of pigment to match the shade of the slab incl rounding of slab & demolition of old slab where directed complete.

S&F in repair vitreous china wash hand basin(Oval shape) white, flat back, size 580x450 mm incl chain and plug and porcelain stopper, brackets, waste pipe incl cutting for and pinning in ends of brackets or erecting stand including dismantling

Material and Labour for reinforced Cement Concrete 1:2:4 (using 20 mm graded crushed stone aggregate) type B1, as in slabs supported on walls, beams and columns, in floors, roofs, landing and in shelves, chajjas etc including removing rubbish off the premises complete all as specified and directed.

M/L rendering 05 mm thick in CM 1:3 on fair faces of concrete finished even and fair in ceilings

M&L three coat of white wash on newly prepared surfaces on ceilling , etc complete.

M & L preparation of new plastered surfaces of walls and applying two coats of oil bound distemper on walls, white or tinted over a coat of chalk whiting, complete all as specified & directed

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with 2mm thick wall care putty and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete.

M & L preparing old decorated surfaces, plastered or unplastered and applying one coat of white wash on walls of buildings Complete..

Demoliton of cement concrete in ground floor paving n exc 15cm thickness ( below or above ground level ) complete.

M&L Cement concrete 1:2:4, type B-1 (using 12.5 mm graded stone aggregate) as in levelling course, coping, window cill etc complete.

M&L Cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base etc complete

M & L 40 mm thick PCC type B - 1, 1:2:4 using 20 mm graded stone aggregate as in flooring finish even & smooth using extra cement complete all as specified.

Supply only 38mm wide glass dividing strips, 3mm thick complete.

S&F in repair vitreous china squatting pan, Orrissa pattern size 580x440mm white with PVC 'P' or 'S' trap with integral foot rest of any pattern incl connection to trap & to flushing pipe, antisyphonage pipe etc making good to floor complete.

S&F in repair Vitreous china wash down water closet pan ( pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) but including P or S trap, seat cover of white colour all as directed and specified.

Material and Labour for dismantling of existing water closet after disconnecting the flush pipe, demolition of entire floor up to bottom of sunken portion, removing of debries, cleaning the top of RCC slab in sunken portion including pheripheral surfaces and plastered with 10mm thick cement & sand mortor (1:3) using WPC finished even and smooth w/o using extra cement cured properly and allowed to dry and applying two or more coats of epoxy resin/polymer modified cementatious coating like brush bond of Fosroc or equivalent both on floor and wall surfaces applied all as per manufactureres instructions and plastering the treated surfaces(after testing for water tightness) 15mm thick with CM 1:3 with WPC including providing 20mm dia GI spout with 300mm projection beyond outer face of wall complete all as specified and directed.

M&L for cement concrete type E2 (1:5:10) using 40mm graded aggregate as in sunken portion of toilets

M&L for rendering 15mm thick in cement mortar 1:4 with water proofing compound 2% by wt of cement, finished even and smooth withot using extra cement in sunken portion complete all as specified. Note:- WPC shall be measured and paid separately

M&L for antifungal Chequered cement concrete tiles 30cm x 30cm x 22 to 25mm thick with grey cement and pigment over & including 20mm thick screed bed in CM 1:6, set, jointed and pointed in neat cement slurry in floors complete.

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete

M&L coloured ceramic glazed tiles 375x250x7mm/450x300x7mm thick as in dado/skirting etc including 10 mm thick rendering in CM 1:4, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in, skirting, dado, etc incl 10 mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete

Taking down shutters of any description exc 1 Sqm & not exc 2 Sqm each

Refixing of shutter of any description exc 1 sqm and n exc 2 sqm in same opening complete.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165

M & L cement concrete type C - 1 (1:3:6) using 20 mm graded stone aggregate as in bed blocks,fillings for holdfast etc complete.

S & F 30 mm thick 2nd class hardwood, factory made flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats.

S & F 35mm thick 2nd class hardwood glazed and skeleton shutters of any no of panels, divided into squares with plain, chamfered or rounded, mitred & rebated sash bars and prepared to receive glass, gauze etc edges of framing plain chamfered or rounded fitted with cat and mitred beads for securing glass etc fitted to chowkats for doors, etc complete, size of member of shutter as specified in SSR Part -I, Sec 8, clause 8.20 (a). Sample of shutter can be seen in GE's office.

S&F Galvanised mild steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks/wooden patti etc complete all as specified.

S & F Aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long.

S & F Aluminium anodised barrel tower bolts of extruded section and fixed 125 mm long.

S & F Aluminium anodised handles of extruded section and fixed 125 mm long.

S & F 75 mm size Butt hinges medium weight cold rolled mild steel and fixed.

S & F 250 mm long mild steel sliding door bolt with hasp, staple( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed.

MS ordinary rat tail rod pattern springs 200mm, including roller and roller plate complete.

M/L preparation of new wooden surface any description over 10 cm width or girth and applying two coat synthetic enamel paint over a coat pink primer all as spfd .

M&L for preparing old painted wooden surfaces of any description not otherwise described , over 10 cm in girth or width and applying one coat of synthetic enamel paint of approved shade all as specified and directed by EIC

S & F Floor door stopper of aluminium alloy body and tongue, anodized, with hand drawn steel spring fixed in door, overall length of cover plate 150 mm

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for.

M&L for reinforced cement concrete 1:2:4 type B1 using 20 m graded stone aggregate as in Beams, cantilevers, bressumm ers, lintels over 1.5m span etc complete all as specified and directed

Supplying and laying of specified outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 with all required fittings ,clipping on walls/ceiling or laying in floors complete all as specified. for the following size :-

20 mm bore

25 mm bore

S & F in repair ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia all as specified (Make : Jindal/Leader/Scico)

S&F in repair for Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F in repair for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F in repair bib tap 15mm chromium plated fancy type long shank with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed .

S&F in repair stop valve 15mm chromium plated screw down, high pressure with crutch or butterfly handle, screwed fboth ends for or iron pipe or for unions and fixed complete all as specified and directed

S&F in repairs 15 mm dia concealed type stop valve fancy type chromium plated etc complete all as specified and directed

S&F in repair Brass chromium plated shower rose 125mm size fancy type with or without swelves joint fixed to iron pipe etc complete all as directed and specified.

S&F in repair PVC connection 450mm long with two PTMT nuts (Prayag)

S&F CP towel rail, 20mm dia, D type,60cm long complete all as approved and directed by the EIC

S&F in repair 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm Complete.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete.

Supply and fix PVC (SWR) pipes single socketed 75 mm dia in any length with rubber ring joints fixed to walls complete all as specified and directed.

Taking down eaves gutter and rain water pipes (any size or pattern ) including all fittings, heads shoes bend swan necks etc at any position ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

S& F PVC (SWR) pipe of 110mm dia single socketed in any length with rubber ring joints fixed to walls all as specified.

S&F PVC (SWR) bends or shoe of 110 mm dia bore

PVC (SWR) junction single, (Single T) 110 mm dia bore equal or unequal

M & L for repairing broken edges of chajja's, roof projection, Fascias etc . In small widths/depths ( exposed area not exc 0.16 Sqm ) by breaking the cracked/loose portion and filling with Cement Mortar / Plain Cement Concrete 1:2:4 ,Type B-0 , using 12.5 mm Crushed stone aggregates , to match the exisitng surfaces incl removing debris , necessary scaffolding , etc all as specified and directed. (Note : Reinforcement if any provided shall be measured and paid separately)

M&L for expanded metal n.exc 4Kg per square metre, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as specified and directed.

M & L for taking down and repairs in patches(area n.exc 2.00Sq min each patches) to plaster/loose surfaces of concrete slabs in sun-shades, chajjas, fascia,shelves, cills, landingsin cement mortar 1:4 /cement concrete 1:2:4 including all necessary arrangments for complete repairs all as specified and directed.(Note : Reinforcement/expanded metal if any provided shall be measured and paid separately)

M&L mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed

S&F in repair chromium plated 25mm conduit curtain rod with brackets ,stops rollers as approved design and fixed to wall complete all as specified and directed.

Material and labour for Preparing previously treated plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M & L for complete removal of existing surface and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete a directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and change of existing colour including removal of sclaed paint and applying two coats of synthetic enamel paint over a coat of red oxide primer for change of existing colour complete all as specified and as directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down ceiling fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M Namkum complete all as specified and as directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One light point controlled by one, two way switch 5 Amps

One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 162 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH, PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH, PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

S & F for Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed at site.

S&F switch socket combination 2 in 1, 3 pin, 5/15 amp multipurpose, flush type universal, all as specified and as directed

S & F for socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

S & F for stepped type electronic fan regulator flushType complete all as specified and directed at site.

Supply and fixing ceiling rose surface bakelite 3 terminals 65 x 50mm complete all as specified.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable, one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Make : Schneider, Havells, ABB.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 volts breaking capacity 10 KA including removal of old unserviceable one complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Make : Schneider, Havells, ABB.

S & F for MCB Single pole and neutral rated capacity 40 to 63 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 2 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 2 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Labour only for refixing the celing fan obtained from item No 178 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Supply, fixing and testing Water heater storage type(Geyser) electric,capacity 25 litres ,230 Volts, 50 hzs, ABS Body, mounting vertical type suitable for 8 bar pressure , BEE 5 star rated , inner tank material ferroglass coating including mounting brackets with Fasteners,Multi-Function Safety Valve , Plastic Pipe (Flexi Pipes) with Adaptors (02 Nos) etc complete all as directed Make- Havells/Bajaj/RACold/ Usha Lexus

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Taking down ceiling fan/ exhaust fan and refixing of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- (Note: Rate of modular cover plates are deemed to be included in the rate quoted)

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 180 here in before but using 2.5 sq mm single core copper conductor cable FRLSH of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm FRLSH copper conductor cable PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for Lamp holder, PVC body suitable for batten fitting completes all as specified.

S & F for Highly efficient LED Bulbs, 9/10 W complete all as specified and directed

S & F for LED mirror light 9/10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Havells, Philips.

S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium ip 66 for building security light fitting luminare with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangement and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer-in-charge.Make:- Bajaj, Philips, Havells

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 4.0 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size concealed in wall etc including one run of PVC insulated 2.5 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 4.0 sqmm cable,one run of 2.5 sqmm cable and one run of PVC casing caping will be measured as one unit

S & F for metal body exhaust fan, AC single phase, 240 V of size 225 mm sweep 1380 rpm with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and M&L for making hole and proper finishing the surface as existing before and taking down of old unserviceable fan complete all as specified and as directed

K K GUPTA (BID ID -3474034)

jai maavindwashni sales & supply (BID ID -3469734)

india trading company (BID ID -3469802)