REPAIR TO LEAKAGE/SEEPAGE AND ROOF TO CERTAIN

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing the debris from site to out side MoD land complete all as specified and as directed by Engineer-in-Charge.

M&L for 100mm thick cement concrete 1: 2:4 type B-2 (using 40mm graded crushed stone aggregate) as in floor including finishing surface even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work built in cement mortar including all quoins, pillars, arches etc complete all as specified.

M&L for brick work with sub class 'B' bricks, straight or curved on plan, exceeding 6.00 mtr mean radius and built in cement mortar 1:6.

Taking down cement plaster from walls and ceilings built in cement mortar including raking out joints, hacking for key, scrubbing down with water etc complete.

M&L for 15mm thick rendering on brick or concrete surface in cement mortar 1:4 including finish surface even & smooth without using extra cement complete on walls.

M&L for sand faced plaster 5mm thick in cement mortar 1:3 over 10mm thick cement plaster in cement mortar 1:4 finished with wooden trowel all as specified and as directed by Engr-in-Charge.

M&L for applying two coat of Acrylic Emulsion Paint on newly plastered surface over a coat of wall primerincluding necessary preparation of surface complete.

S&F in repairs 35 mm thick precast cement concrete jallies in 1:2:4 mix type B-0 (using 12.5 mm graded crushed stone aggregate) with wire fabric, set and jointed in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly steel surface of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint by Mechnical paint sprayer over a coat primer in ceiling including covering to walls and glazing and cleaning the surface after work completed to entire satisfaction of Engr-in-Charge.

Dismantling of floor, hearth or wall tiles/Granite stone/ Kota stone/ marble stone / chequered tiles etc including bedding (but not backing) and removing the debris from site to out side MoD land complete.

M&L for non skid coloured ceramic tiles 7-8 mm thick (square/rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid as in floor,set and jointed in neat cement slurry over and including 15 mm thick cement screed bed in cement mortar 1:6 and pointed with coloured cement to match the tiles .

M&L for vitrified tiles 10 mm thick 1st quilaty (Square/rectuangular) polished, light shade, area of each tiles not exceeding 0.36 Sqm laid as in floors , set and jointed with neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15mm thick screed bed in cement mortar 1:6 complete.

M&Lfor Glazed ceramic coloured tiles (colour & shade as approved) of size 300mmx200mmx7mm thick in vertical surfaces such as in skirting and dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over 15mm thick rendering in cement mortar (1:4) complete.

M&L for polished granite stone slab 18 to 20mm thick fixed on vertical surfaces such as dado, skirting, steps etc, set and jointed with neat cement slurry and pointed in white or coloured cement to match the shade o s tone over and including 15 mm thick cement screed bed in cement mortar 1:4 complete.

M&L for polished granite stone slab 18 to 20mm thick fixed as on floor /platform etc, set and jointed with neat cement slurry and pointed in white or coloured cement to match the shade of stone over and including 15 mm thick layer of cement screed bed in cement mortar 1:4 complete.

M&L for cement concrete tiles 25cm x 25cm x 22mm thick,machine pressed,set jointed and pointed in neat cement slurry in floors and cut and polished with grey cement and pigment over and including 20 mm thick cement screed in CM 1:6 complete.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

S&F for 4mm thick ordinary sheet glass fixed with putty and glazing pins/ springs clips etc not exceeding 0.5 Sqm each pane complete.

S&F for 5.5mm thick sheet glass, ordinary quality fixed with clamps and oil putty etc exceeding 0.5 Sqm each pane complete.

S&F for 6.4mm thick rough cast wired glass glazing with oil putty and glazing pins/ spring clips exceeding 0.5 Sqm but not exceeding 0.75 Sqm each pane.

S&F for 8mm thick etching glass fixed with stainless steel clamp, washer etc complete including grinding edges for smooth finish of size exc 1.00 sqm but n.exc 2 sqm each pane .

S&F in repair for 2nd class hard wood plain fillets, square, rectangular or tringular in section, wrought, bull nosed splayed chamfered or rounded on one face secured with nails or brands of sectional area exc 3 Sqcm but not exceeding 6 Sqcm complete.

M&L for preparation of old painted steel surface of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10cm of width or girth not otherwise described and applying one coat of synthetic enamel paint by Mechnical paint sprayer on ceiling including covering to wall, glazing etc and cleaning the surface after work completed to entire satisfaction of Engr-in-Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern in roof covering or cladding complete.

S&F for Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in roofs, walls/ clsdding etc. with grade of zinc coating 120 Gm/Sqm complete all as specified.

S&F in repair for 110 mm bore PVC (SWR) pipe , single socketed, in any length with rubber ring joints fixed to walls with suitable clamps complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC (SWR) bend 110 mm bore in any length complete.

Dismantling wall and ceiling boards ( fibre , pulp,insulation etc.) or insulation boards / slabs / blankets , any thickness including fillets complete.

M & L for provding false ceiling of 15mm thick fine fissure board sharped finished mineral fiber accountic false ceiling tiles with back of the duly sanded and finshed with a coat of protective paint and front duly finished false system of size (600x600) mm having noise reduction co-efficient of 0.55 light reflection of 80% thermal conductivity k=0.057 W/WWC and humidity resistance of 95% fixed to true look PVC die KL -24 suspension system (Hot dipped aglvanised steel section) of exposed T- Section consisting of perimeter wall angle of size 24mmx24 mm of thickness 0.45 mm c/c universal main runner of T -Shape with double rotary siticing of size (38x25) mm of lenght 1200mm made from 0.33mm GS steel of lenght 3.60 mtr to be spced at 600x 600mm size c/c cross runner T- shape wtih double rotary siticing of size (30x24)mm of length 1200mm made 0.25 thick GS sheet spaced @ 600mm c/c (600mm 600mm) size complete all as specified and directed by Engineer -in- Charge.

Demolition of cement concrete (unreinforced)/Paver block in ground floors and pavings n.exc. 15cm thick above or below ground level and removing the debris from site to out side MoD land complete.

M&L 25 mm thick sand filling in sub base of finishes including consolidation for paver block all as specified.

M&Lr for 80 mm thick factory made reflective type, heavy duty, smooth finish, cement concrete interlocking paver block of M -40 grade made by block making machine with strong vibratory compaction, casted in rubber/PU mould on a vibrating table of approved size and design/ shape, laid in required colour and pattern , filling the joints with coarse sand including vibrating the surface with vibrating machine complete.

S&F in repair speed bump (speed breaker) made of heavy duty ABS body with high resistant wear & tear property, US stabilized black and yellow coloured, high reflective reflector having length 500mm, width 400 mm and height 75mm i.e 500mm x 400mm x 75mm size fixed on ground/road/pavement etc with necessary bolt as recommended by manufacturer including hollow space of speed bump to be filled with PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate complete all as specified and directed by Engr-in-Charge.

Dismantling old mild steel barbed wire fencing complete all as specified and directed.

S&F for galvanised 2 strand, steel baded wire 2.24mm dia barbed with 2 mm dia barbed of 75mm spacing and straining and fixing to any type of standard rail, straining bolt including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured) complete all as directed by Engr-in-Charge.

M&L for preparing of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying one coat of aluminium paint complete all as specified

Dismentling of boarding of any description, fixed in any position with nails.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, fillets etc and making good, cutting not exc 10 cm girth in brick wall for panelling.

S&F for 2nd class hard wood plain fillets square or rectangular in section clean swan secured with nails or brands of sectional exc 13 Sqcm but n.exc 25 Sqcm secured with nails as in wall panelling.

S&F for 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed witrh screws to timber frame work in narrow widths n.exc 15 cm each rebated or flat edge as in wall panelling.

S&F for 6mm thick plywood grade BWP, type BB fixed with screws to timber frame work as in wall panelling.

M&L for Curved or flat raised borderd using POP not exc 10cm in width and avg 10mm thick all as Specified.

a.k constructions

M/S PRADEEP ENTERPRISES

M/S Satyam Associates