PROVN OF COVERED PASSAGE , PARKING SHED AND TOILET FOR DENTAL OFFR, STAFF AND PERS LINE OF MDC AT OLD AMRITSAR CANTT

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each hole not exceeding 0.5 Cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and remvoing surplus soil to a distance not exceeding 50m and making good surfaces in soft/loose soil complete all as specified & directed by the Engineer-in-Charge.

Material & Labour for PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in foudation Filiing , mass concrete,sub base or similar works complete all as specified and directed by Engineer-in-Charge.

Material & labour for Rolled mild steel work Fe 410 -W (Grade E- 250) quality A, as in fencing posts with or without Y/U/Swan Neck made of angle or other section, made to shape complete, welding, drilled for fixing or holding of barbed wire or concertina coil , etc. to be prepared for hanging or steel hanging fittings; also fastening and fixing complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Rolled mild steel work Fe 410 -W (Grade E- 250) quality A, as in Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., made to shape complete, welding, drilled for fixing or holding of etc. to be prepared for hanging or steel hanging fittings; also fastening and fixing complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparation of new or previously untreated steel surface of any description over 10 cm width and girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed by the Engineer-in-Charge.

Suppy & Fixing for pre-painted galvalume aluiminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge of roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Material & Labour for hard core of gauge not exc 63 mm of broken stone or boulders spread and levelled in layers not exc 15 cm thickness watered and rammed to a true surfaces complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Screed bed or bedding layer of cement mortar 15 mm thick with cement mortar ( 1:6) for laying floor surface finished even & fair complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Chequered cement concrete tiles 32cm x 20cm x 30mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75 mm thick plain Cement concrete , 1:4:8 type D- 2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with gray cement and pigment complete all as specified and directed by Engineer-in-Charge.

Surface dressing n exc 15 cm deep in soil/loose soil complete all as specified and directed by Engineer-in-Charge.

Exacavation in trenches not exc 1.5 cm deep & 1.5m wide and not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Returning , filling in including spreading, levelling watering and well ramming in layers each layer not exceeding 25cm thick complete all as specified and directed by Engineer-in-Charge.

Removal of surplus spoil to a distance exceeding 200metres not exceeding 500metres and depositing where directed of level not exceeding 1.5mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) as in boundary wall, drain etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Brick work with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) as in boundary wall, drain etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with CM (1:6) finished the surface for even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with CM (1:4) finished the surface for even and smooth, with & including using lequid water proofing compound @100 ml per 50 kg of cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for rendering 5mm thick in CM 1:3 to fair face of brick works or concrete surfaces of ceiling finished the surface for even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new plastered or unplastered surfaces of walls and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new plastered or unplastered surfaces of walls and applying two coat of cement base paint over a coat of primer etc. complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new plastered or unplastered surfaces of ceiling , chajjas and applying three coats of white washing complete all as specified and directed by Engineer-in-Charge.

Material & Labour for RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) nominal mix in Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge.

Material & Labour for RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) nominal mix in slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves complete all as specified and directed by Engineer-in-Charge.

Material & Labour for RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) nominal mix as in lintels upto 1.5m clear span and lintel band, roof band and other similar items including form work complete all as specified and directed by Engineer-in-Charge.

Material and labour for use and waste of form work to for soffits of suspended slab, such as roof slab, floor slab landing and similar work not exceeding 200 mm thick etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Fair finished flat form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal of flopping and similar work complete all as specified and directed by Engineer-in-Charge..

Material and labour for TMT bar upto & including 10 mm dia and over cut to length for columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia or securing with clip quality conforming to Fe-410-S or Fe-410-0 complete all as specified and directed by Engineer-in-Charge.

All as per item No 33 but 6 mm to 8 mm as in stirrups, spacer bars etc complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 35 mm thick Second class hardwood (rail and styled) plain framed panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stiles as per IS : 1003 (Part-I), klin seasoned and chemically pressure treated.

Suppy & Fixing for factory made solid PVC Moulded door shutter with wood free EPS board core, 28 to 30 mm thick (stiIes) with 2, 4 or 6 raised panel design with 2 mm thick Moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on backs face, supplying and fixed in frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new wooden surfaces over 10 cm girth or width and apply two coat synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 150 mm aluminium , anodised, barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 250mm aluminium alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for butt hinges 100mm size medium weight cold rolled mild steel, fixed with screws or welded to steel frame complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for extruded aluminium alloy handles, fabricated type, anodised all as specified of size 150mm long complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as stopper, cleat, pintal hinges, hold fast etc all as shown on drg No CEJZ/TD-06/07 dt 07.06.07 incuding cutting holes complete all as specified. Note: Sheet glass and painting shall be measured and paid Separately. complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 4mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane in any position complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spiker framed guard bars barred iron doors ladders; framed balusters walk ways railings framework of watertanks and similar work conforming to Fe-290 Gde-165 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Non skid Ceramc tiles 400x400x6 to 7 mm thick joint less thick light coloured (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in while or coloured cement to match , with & including 15mm thick screed with cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Glazed cermic coloured tiles 450mm x 300mmx 7mm /300mmx300mmx7mm thick on vertical surfaces of walls such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles over , with and including 10 mm thick bedding layer of cement mortar 1:4 co complete all as specified and directed by Engineer-in-Charge.

Material and labour 50mm thick plain cement concrete 1 : 3 : 6 type C1 (using 20 mm graded stone aggregate) as in paving/ plinth protection laid in pannels including necessary form work, finished even and smooth without using extra cement, & filling the joint with bitumenous filler (bitumen mixed with sand) complete all as specified and as directed by Engr-in-Charge .

Suppy & Fixing for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe)including connection to trap, and to flushing pipe, anti-syphonage pipe etccomplete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demilition of PCC / Lime concrete bedding existing pan complete as in repairs complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) front or back inlet including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc and making good to floor complete as in repair complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for plastic water closet seat, white , closed patern withflat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repair complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for PVC waste pipe 32/38/40 mm dia, 600 to 750 mm long comlete all as specified and directed complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Vitreous China wash basin, white, flat back, size 500 X 400mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand complete as in repai complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for PVC connections 15mm size with PTMT nuts of length 450 mm. complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for rotational moulded polythene, triple layers, water storage tank 1000 litres capacity, closed top, cylindrical, hoisted and fixed in position with and including 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod , complete all as specified and directed by the Engineer in Charge.

Suppy & Fixing for 15mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 20 mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 15mm dia Stop valves, high pressure, with crutch or butterfly handle, chromium plated, fancy type, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 15 mm Bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down screwed for iron pipe of 15mm bore and fixed in repair complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

Suppy & Fixing for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and wasteVitreous China urinals, bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring fixed to wall complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore PVC (SWR) pipes Single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore P\/C (SWR) bends of any radius complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore PVC (SWR) junction single (Single 'T') equal or unequal with access door complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 110 mm bore PVC (SWR) Vent Cowl complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 20mm thick Granite stone (of any type) slab work (table rubbed and polished) in steps, jambs, pillars, window cills,platforms, urinals partition and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed in CM (1:6) complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for 100 mm Stack clamps made out of Flat iron 50x5 mm and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wail or roof complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples in window and door as in new door/window complete all as specified and directed by Engineer-in-Charge.

Material & Labour for providing precast reinforced cement concrete 1:2:4,Type B1 using 20mm graded crushed stone aggregate as in Ianding, landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings,throating etc. and setting in cement mortar (1:6) complete with joints to match, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for providing plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in roof kerbs, copings ,kneelers, apex, stones,and similar articles with plain faces including chamfers, weatherings,throating etc.complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm at 180 degree temperature in each layer ( first layar below APP membrane and second layer above APP membrane) on 0.40 kg/sqm bitumen primer surfaces including cleaning surfaces etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces complete all as specified and directed by Engineer-in-Charge.

Material & Labour for two coats of aluminium paint over acoat of priming with Aluminum red oxide over APP membrane inclusing preparation of previously untreated surfaces

Material & Labour for reinforced concrete pipes 150mm dia, class NP3 laid and jointed in neat cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Hume Pipe septic tank for 10 users designed to carry sewage and sullage water, with and including excavation in any type of soil, 150 mm thick PCC 1:4:8 type D2 as in foundation, Vent shaft, connection, RCC cover slab made in M-25 cement concrete (nominal mix) / SFRC cover, complete to the entire satisfaction and all as specified and directed by Engineer-in-Charge.

Material & Labour for Soakage wells of size 1.2 Metre dia X 1.5 Metre effective depth with and including excavation in any type of soil, PCC in foundation in PCC 1:3:6 type C2 using 40mm graded aggregate, walls of honey combed masonry with top ring of M-25 cement concrete (nominal mix) including intercepting chamber and screen chamber made of Brick masonary in CM 1:4, RCC cover slab made in M-25 cement concrete (nominal mix) / SFRC cover, including interconnecting pipes of RCC/DWC complete filled with brick bats of size complete to the entire satisfaction and all as specified and directed by Engineer-in-Charge.

Material & Labour for Wiring for One light point/Bell/Fan point controlled by one switch. complete with 1.5 sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 83 herein before but for One 3 pin 5 amps switch socket on independent board complete all as specified and directed by Engineer-in-Charge.

All as per item No 83 herein before but One 3 pin 5 amps switch socket on same board complete all as specified and directed by Engineer-in-Charge.

All as per item No 83 herein before but with FRLS cable 2.5 sqmm (nominal area) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wirte PVC insulated 1.5 sqmm copper multistranded conductor connecting to common earth and earth dolly complete all as specified and directed Note for items No. 83 to 86 :- The wiring shall be done in proper colour coding using red,yellow and blue for phase,black for neutral and green for earth leads. complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for switch piano one way 5 A, SP, 230 Volts complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for Socket outlet 2 in 1, 3 pin 5 Amps Flush type complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for Switch outlet 2 in 1, 3 pin15 Amps Flush type complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for ceiling rose surface bakelite 3 terminals 65x32mm complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant/batten fittings complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for wall/ceing mounting LED 18 Watt PC Diffuser tube light fitting complet with all aceesories 1x18W LED suitable for domestic application 240Volts 50HZ including one tube rode and internally pre-wired with 1.5 sqmm twin twisted flexible copper conductor and complete all as specified and directed by Engineer-in-Charge.

Material & Labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 2.5 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete all as specified and directed by Engineer-in-Charge..

Suppy & Fixing for exhaust fan 250 mm sweep metal body heavy duty including cutting of wall /window/lowers and fixing arrangement complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing MCB double pole, 240 volts, 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed by Engineer-in-Charge.

Suppy & Fixing for LED Blub 9 Watt, 240 Volts complete all as specified and directed by Engineer-in-Charge.

ESS KAY BUILDER

Sai Construction Co.