SPECIAL REPAIR TO BLDG NO MH 48 SINGLE LIVING OFFRS ACCN AT MH MHOW UNDER GE MAINT INF SCHOOL MHOW

Amount

Taking down shuters of any description n.exc 1 sqm each and removing from site complete all as specified

Taking down shuters of any description exc 1 sqm but n.exc 2 sqm each complete all as specified

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified

M&L for applying two coats of superior quality oil emulsion distember over a coat of primer over a coat of Acrylic / Water proofing wall care putty on walls including preparing surface complete all as specified .Note:- Putty shall be measured and paid seperately under relevant item.

M&L for preparation of old decorated surfaces of wall including brooming , scraping down,smoke spot, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and applying two coats of superior quality oil emulsion distemper white/coloured over a coat of Acrylic / water proofing wall care putty (wherever required )all as specified Note:- Putty shall be measured and paid seperately under relevant item.

M&L for preparation of old decorated surfaces of wall including brooming , scraping down,smoke spot, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and applying one coat of superior quality oil emulsion distemper all as specified

M&L for preparation of new plastered surfaces of walls and applying two coats of Acrylic Smooth exterior paint of required shade (@ 1.67 litre /10 sqm) over a coat of primer(@ 2.20 kg/10 sqm) of same make base over a coat of putty all as specified Note:- Putty shall be measured and paid seperately under relevant item

M&L for preparation of old decorated surfaces of wall including brooming , scraping down,smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying two coats of exterior weather proof water base emulsion paint white /coloured over primer of same make white cement based putty (wherever required) all as specified Note: Putty shall be measured and paid seperately under relevant item

M&L for preparation of newly plaster surface of wall and and applying 2mm thick Acrylic / water proofing wall care putty in two coats (each coat not less than 1mm) surface finished even and smooth with sand paper complete all as specified

M&L for 2mm thick Acrylic / water proofing wall putty in two coats (each coat not less than 1mm) and surface finished even and smooth with sand paper complete all as specified

Demolition of brick work built in cement mortar including all quions ,arches , pillars etc complete all as specified

M&L for brick work with sub class `B ` modular brick straight or curved on plan exceeding 6.0m mean radius built in in cement mortar 1:6 complete all as specified

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement complete all as specified

M&L for rendering 10 mm thick in cement mortar 1:6 on fair faces of wall / concrete surface finished even and fair complete all as specified

M&L for preparation of old painted surfaces of wood / wood based materials exceeding 10cm in width or girth and applying one coat of synthetic enamel paint all as specified.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick ( below or above ground level ) complete including removal of debries out side MD land all as specified

M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in sub base, levelling course, etc complete all as specified

M&L for PCC1:4:8 type D2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified

Dismantling of floor, hearth , or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the primeses complete all as specified

M&L for scratch free Glazed (Porcelain) Vitrified Tiles (GVT) / Polished Glazed Vitrified Tiles (PGVT) 9mm to 10mm thick (square or rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.72 sqm (ie) size 600mm x 600 mm / 600 mm x 1200mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed. Make of tile : Superior quality tiles from Kajaria/Somany/Orient Tiles. Note : (a) Size and pattern / texture of GVT (Matt Finish) / PGVT(Glossy Finish) shall be approved by GE (b)Glazed Coating on GVT / PGVTshall not be less than 1mm thick .

All as per item No 20 above but as in skirting / dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified

M&L for scratch free Glazed (Porcelain) Vitrified Tiles (GVT) / Polished Glazed Vitrified Tiles (PGVT) 9mm to 10mm thick (square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm (ie) size 600mm x 600 mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed. Make of tile : Superior quality tiles from Kajaria/Somany/Orient Tiles. Note : (a) Size and pattern / texture of GVT (Matt Finish) / PGVT(Glossy Finish) shall be approved by GE (b)Glazed Coating on GVT / PGVTshall not be less than 1mm thick .

All as per item No 22 above but as in skirting / dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified

M&L for glazed ceramic coloured tiles (Matt / Gloss finish) of size not less than 450x300x7 mm thick as in vertical surfaces such as on wall ,dado,skirtting etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 15 mm thick backing coat on fair faces of brick work in cement mortar 1:4 complete all as specified Make of tile:- Superior quality tile from Kajaria/Somany/Orient tiles. Note: (b) Pattern/Texture and finish of wall tile shall be approved by GE

M&L for non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of size 300x300 /400x400mm in floors set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1: 6 complete all as specified

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified

M&L for machine cut kota stone slab in flooring 20mm to 25mm thick laid over and including 15mm thick screed bed in cement mortar 1:6 and pointed with cement mixed with pigment to match with the shade of slab including rubbing and polishing complete all as specified

M&L for 18mm to 20 mm thick Granite slab work (table rubbed and polish) of approved quality of required size in floor,wall,cooking platform and like bedded and jointed in grey cement slurry and pointed with coloured cement (1:2) usig marble dust with admixture of pigment to match the shade of granite stone laid over and including 20 mm thick screed bed in cement mortar 1:4 including polishing by using mechanical grinder complete all as specified and directed. Note : Size of Granite slab shall be maximum as available at market /as per site requirement and shall be approved by GE

M&L for 60mm thick machine pressed rubber moulded precast cement concrete interlocking paver block (glossy finish) of M-35 Gde of approved shape, size and colour conferming to IS 15658-2006 and including joints filled with sand and stone dust 50mm thick as in levelling course of interlocking complete all as specified

M&L for chequered cement concrete tiles with grey cement and pigment of size 25cmX25cmX25mm thick ,set jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for chequered cement concrete tiles with grey cement and pigment of size 40cmX40cmX40mm thick ,set jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stone / kerb block ,machine pressed ,bul lnosed shape at top as directed and finished the surface even and smooth including necessary form work /moulding ,fixing, jointing kerb block in cement mortar (1:4) complete all as specified

M&L for preparation of old decorated surfaces of wall by removing existing putty /distemper upto plaster level and applying two coats of Sureseal by Dr Fixit or other equivalent as approved by GE and subsequently apply two cpats of Oil Emulsion Distemper over a coat of 2 mm Acrylic / water proofing wall care putty (each coat not less than 2mm) all specified and directed Note : (a) Applying first coat of Sureseal by Dr Fixit (no dilution) & allow it to dry for 6-8 hours. (b) Applying second coat of Sureseal by Dr Fixit (no dilution) perpendicular to first coat & allow it to dry for 6-8 hours. (c)The work of Sureseal treatment shall be got executed through expert team of Manufacturers or their authorised applicator of Manufacturer .Quantity of Sureseal shall be dedided by expert team as per site requirement. (d) Putty and Oil Emulsion Distemper Shall be measured and Paid Seperately under relevent item

M&L for preparation of old decorated surfaces of wall by removing existing putty / distemper upto plaster level and applying two coats of Rain Coat Neo (By Dr Fixit or other equivalent approved by GE) over a coat of 2 mm Acrylic /Water Proofing Wall Putty (each Coat not less than 2mm) complete all as specified . Note : (a) Apply first coat of Rain Coat Neo and allow it to dry for 6-8 hours . (b) Apply second coat of Rain Coat Neo perpendicular to first coat & allow it to dry for 6-8 hours. (c) The work of RainCoat Neo treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer and quantity of Raincoat Neo shall be dedided by expert team as per site requirement. (d) Shade /Colour /Texture of Raincoat Neo shall be approved by Engineer in Charge (e) Putty Shall be measured and Paid Seperately under relevant item

M&L for preparation of old decorated surfaces of wall by removing existing putty/distemper upto plaster level and applying one coat of Rain Coat Neo (By Dr Fixit or other equivalent as approved by GE over a coat of 2 mm Acrylic/WaterProofing Wall Putty (each Coat not less than 2mm) complete all as specified Note : (a) The work of Rain Coat Neo treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer and quantity of Raincoat Neo shall be dedided by expery team as per site requirement. (b) Shade/Colour/Texture of Raincoat Neo shall be approved By Engineer in Charge (c) Putty Shall be measured and Paid Seperately under relevant item

S&F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed / Glass and one shutter wire mesh) with following specification complete all as specified and as directed by Engineer-in-charge. (i) Windows frame of cross section 101mm x 44mm (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm (iii) Sliding shutter frame of cross section 40 x 18mm (iv) 4 mm thick glass superior quality. (Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 No. (Min) (vii) Sliding rollers per shutter - 02 Nos. (Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 No. Note-:(a) Thickness of Aluminium Section shall be minimum 2 to 3mm (b)Drawing and size of Window shall be provided by Engineer- in -Charge as per site requirement.

S&F powder coated aluminum door with the following specification and making good the adjacent surfaces, complete all as specified and as directed. (a) Cross section of chowkhat frame 101.60x44.45.mm (b) Cross section of hanging and meeting style 83x44mm (c) Top rail of cross section 114x44mm (d) Bottom rail of cross section 114x44 mm (e) Locking rail (middle rail) of cross section 83x44mm. (f) 4 mm thick glass superior quality. (Min) (g) Aluminum handle eisc type -02 Nos per shutter (inside & out side). (h) Aluminum door stopper heavy duty-01 No per shutter. (i) Aluminum tower bolt 200mm long-01 No per shutter (inside). (j) Concealed Lock with key superior quality make and type as approved by GE openable both from inside & out side -01 No per shutter. Note- 1.Thickness of Aluminium Section shall be minimum 3 mm thick 2.Drawing of Door size and details shall be provided by Engineer- in- Charge as per site requirement.

M&L for plain cement concrete 1:2:4 type B1 using 12.5mm graded stone aggregate ,25mm thick as in roof top finished even and smooth complete all as specified

M&L for rendering 15 mm thick in cement mortar 1:4 on roof surface mixed with and including WPC as per manufacturer's instruction's and finishing the surfaces even and smooth without using extra cement complete all as specified

M&L for water proofing roof treatment with polymeric standard water proofing membrane, Aqua flex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd / Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness complete all as specified and described as under:- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per Manufacturer's instruction complete all as specified and directed. (b) Supply & laying water proofing 3 mm thick APP polymeric proofing membrane of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100 micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed (c) Aluminium bituminous paint @0.15 Kg/Sqm shall be applied over the APP membrane surface. NOTE:- The work of water proofing treatment shall be got executed through expert team of Manufacturers or their authorised applicator

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and minimum 150mm end lap laid to slope all as per Manufacturer / profile maker instruction complete all as specified and as directed.

S&F Mild steel hollow ,Joist, channel, angle, tee or tubular Section work in tubular trusses, purlins, rafter, tubuler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified

S & F MS framed work as in doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc, to prepared for hanging or sliding with including either hooks and hinges also fastening grills, grating, hold fast of doors and windows chowkat etc, with ends of bars shouldered and or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanksand fixing and similar work confirming to fe 290 Gde E-165 all as specified

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified

S&F PVC prelam sheet wall/ceiling paneling of thickness 5mm consisting of panels having size 1.22 M x 2.44 M stuck on inner frame work of 50 mm wide strips of 5mm thick prelam PVC sheet of 600 Kg/cbm density manufactured by an ISO-9000 certified company. The strips should have in their centre a groove of 6mm width and 1mm depth of sinking the head of the screw used to fix the strip to the wall vertically at an equal interval of 10” between two PVC strip. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fastners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joints of two panel for aesthetic looks. The exact size of the panel and correspondingly of grid may vary depending on the size of wall. Optionally a strip of 5mm thick PVC sheet of width 75mm feathered at edges shall be struck at the places where two panels are jointed, using solvent complete all as specified and as directed

S&F Anodised aluminium snap grid size 605mmx605mm frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F Exposed metal frame ceiling with 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid complete all as specified. (Note: Frame work for ceiling shall be measured and paid separately under relevant item)

S&F Gypsum Board 12mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre on GI frame work for seamless ceiling comprising of GI perimeter chennel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm susoended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre inluding finishing the joint of face board with specially formulatted jointing compound and 48 mm wide fibre tape to provide seamless finish Ceiling shall be sealed at joints and finished with jointing compound etc complete including finishing the exposed surfaces of false ceiling with two coats of plastic emulsion paint over a coat of primer complete all as specified and directed.

S&F PVC Ceiling Lining (False Ceiling) consisting of 5mm thick Plain colour PVC sheet 8 to 10 mm hollow section inclusive of solvent cement and fixing at site on frame work as per requirement on site complete all as specified and directed.

S&F fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partisions with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified

S&F aluminium coloured power coated window and ventilator shutters, sliding type without sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws etc complete all as specified and directed.

S&F aluminium coloured power coated door shutters, aluminium section weighing mininimum 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. .

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors/window/partition including necessary cutting / moulding and chamferrring of edges for service window/counters complete all as specified and directed.

S & F for galvanised Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed.

S&F PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet 8 to 10 mm hollow section inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for Veneered decorative 18 mm plywood, grade 1 (with BWR resin) with decorative laminate min 1mm thick on both faces; fixed with screws to timber frame work as in cupboard shelf/partition all as specified and drected Note: Colour and texture of laminate shall be approved by Engineerr-in-charge.

S&F 12mm thick Frosted Toughned Glass fixed on patch hinges / pivot for smooth functioning in door shutter including stainless steel handle of 8 inches long and mortice locking arrangement complete all as specified

S&F factory made single side prelam PVC sheet door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with ms square tube, & edges will be painted to match with prelam sheet complete all as specified and as directed.

S&F factory made Single Side Prelam PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Single Side Prelam PVC sheet for top rail, lock rail & bottom rail. Panelling of Single Side Prelam PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement including Hinges for fixing and handle/tower bolt as per site requirement complete all as specified and as directed.

S&F factory made 25 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free, water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In- charge,Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and as directed.

S&F factory made 100% solid WPC (Wood polymer composite) Door frame 90mm X 45mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade), calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/borer proof, water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-charge,Material test certificate and authentication should be compulsory provided by the manufacturing company including hold fast or fasteners, complete all as specified and as directed.

S& F Rotational moulded Polyethylene water storage tank 1000 liters capacity (cylidrical vertical with closed top) of three layered hoisted and fixed in position all as specified in SSR part I complete

S& F Rotational moulded Polyethylene water storage tank 500 liters capacity (cylidrical vertical with closed top) of three layered hoisted and fixed in position all as specified in SSR part I complete

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified

All as per item no 66 above but 20mm bore

S&F in repair vitreous china European wash down water closet pedestal pattern (S trap) of size 570x370x390mm white icluding seat cover excluding flushing cistern and flush pipes complete all as specified and as directed .Make:Plumber. Cat Part No.- PBW-EWC-0025

S&F in repair PVC valve less,syphonic action type flushing cistern,low level ,10 litres capacity ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed.Make:Plumber /Essco of jaguar(Economical Range)

S&F in repair CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified Make:Plumber /Essco of jaguar(Economical Range)

S&F in repair fancy type chromium plated 15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified Make :Plumber/Essco of jaguar(Economical Range)

S& F CP toilet paper holder with Lid Cover complete all as specified Make :-Plumber/Essco of jaguar(Economical Range)

S & F in repair vitreous china wash basin white (table top) of size 520x360x125 mm including 32mm brass CP waste coupling complete all as specified and as directed . Make : Jaquar (or equivalent) .Cat Part No.- FLS-WHT-5931

S&F in repair Vitreous China Urinal, Half stall type,of size 355x340x535 mm , white with grating and union for discharge pipe, urinal spreader including all fixing accessories, with waste pipe complete all as specified and as directed Make :Jaquar (or equivalent) ,Cat Part No. URS-WHT-13261H

S&F in repair vitreous china Single Piece WC (P trap) of size 360x655x765 mm white with UF Soft Close Slim Seat cover,hinges, dual flush cistern fitting, fixing accessories and flush pipes complete all as specified Make: Jaquar (or equivalent) ,Cat Part No: LYS-WHT-38851P180UFSM

S&F health faucet with flexible pipe of one meter length including wall hook for EWC complete all as specified Make :Plumber/Essco of jaguar(Economical Range)

S&F in repair PVC (SWR) floor trap plain or multi with stainless steel grating including joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified

S&F in repair PVC (SWR) pipes 100mm bore single socketed in any length with rubber ring joints laid on wall / floor complete all as specified

S&F in repair PVC ( SWR) bends 100mm bore any radius

S&F Stainless steel railing includng all fixing arrangement complete all as specified and directed.

M&L for salt glazed stoneware drain pipe of 150mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested internal dia of pipe 150mm complete all as specified

M&L for RCC type 1:2:4 type B1 using 20 mm graded granite stone aggregate) as in precast cover slab for manholes and soak well cover slab etc set in cement mortar (1:4) etc with and including necessary form work all as specified . Note:- Reinforcement shall be measured & paid separately under relevant item.

M&L for plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations, filling and mass-concrete complete all as specified

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cespits, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in Hard / dense soil complete all as specified

Removing excavated materials (soil) to a distance not exc. 50 meter and depositing where directed at a level not exc. 1.50 meter above the starting point complete all as specified and directed.

Returning, filling in, soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete.

E/M PORTION

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc and removing materials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately ) and making good distrubed surfaces of walls, floors etc. complete all as specified

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M complete all as specified

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified

Taking down old /unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified

Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE E/M complete all as specified

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified for the following :

One light point controlled by one, one way switch 5 Amps

One light point controlled by one, two way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 point 5 Amps switch socket outlet point controlled by one switch on Same board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on Independent board.

One bell point controlled by one, bell switch 5 Amps

All as per item No 95 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket cobmination point on independent board including 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No 95 here in before but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for Geyser point/AC point connecting to metal plug and socket DB including 4.0 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified.

S&F Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified

S&F Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified.

S&F Bell push modular 6 Amps single module complete all as specified.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified.

S&F modular step type fan regulator 50 to 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified

S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified

S&F in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or other equivalent in Wipro

S&F Decorative ultra slim LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified Make:- Havells Cat No. LHEXACP7IN1W010 or other equivalent make in Wipro/Philips.

S&F Decorative wall mounted luminaire brushed nickel finish fixture with opal glass diffuser made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 7W watts complete all as specified . Make:- Havells Cat No LHFOAJE1TZ11060 or other equivalent make in Philips/Crompton/wipro.

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified. Make: Bajaj Cat No ENXT P 36L WH CR PC SD or other equivalent make in Philips, Wipro/Havells

M&L for Sub main wiring in repairs with two runs of single core FR LSH PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including surface non metallic rigid PVC conduit not less than 25mm dia and all fittings like bends, tees, saddles etcincluding one run of FR LS PVC insulated unsheathed 4 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete. Make - HPL/L&T/HPL/Havells

M&L for Sub main wiring in repairs with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25/32 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified Note:- Two runs of 6 sqmm cable,one run of 6 sqmm earth cable and one run of PVC conduit shall be measured as one unit

S&F in repairs flush mounting factory made Vertical TPN DB 8 Way, IP-43 Protection -IK 08, with metal double door with 200 Amps rated copper busbar with 2 neutral bar, earth bar and cables ties for cable management fully insulated bus bar with set of wires and door earthing with provision of sapce for TP/FP 100-125 amps G Frame MCCB as incomer and SP/TP MCBs as out going 8 way complete all as specified Make:- HPL/L&T/HPL/Havells

S&F in repairs double door SPN DBs 08 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified . Make : HPL/L&T/HPL/Havells

S&F in repairs double door SPN DBs 04 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified Make: - HPL/L&T/HPL/Havells

S&F in repairs MCCB FP 125 Amps 25 KA including connection with suitable size aluminium / copper lugs complete all as specified. Make: - HPL/L&T/HPL/Havells

S&F MCB SPN 6 to 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified

S&F metal clad box suitable for 230 volt 50 Hz for AC connection three pin and socket with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified

Labour only for refixing the celing fan/ Exhaust fan obtained from item No 5 above with replacement of unserviceable 3 core PVC insulated PVC sheated multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

S&F energy efficient exhaust fan of metal body 225/230 mm sweep Ventil Air -DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection including making suitable size of hole to existing brick wall for fan base and making good the same as per existing compelte all as specified and directed.

M&L for earthing complete with galvanisedsteel earth plate electrode60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate otless'than 1.5 metres below normalground level, connected togalvanised earth lead wire 4.0mmdia by means of bolts, nuts, checknuts and washers of galvanised ironor steel all as shown in electricalplate No. 3 connected to earthing testpoint all as specified or indicated including testing on completion.Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Taking down existing old Extg unserviceable LT UG/ service cable of any description and size complete all as specified and directed.

M&L for sand cushioning with dry and clean sand over and under the under ground cable in trenches , ducts for cable protection complete all as specified.

Supply and laying reinforced precast concrete cable cover, class LV, type 1 flat , size 250mm x 150mm x 40mm complete all as specified

Supply and laying galvanised iron pipe 'light Grade' 50 mm in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 3.5 core x 35 Sqmm complete all as specified

ss construction

Chitragupta Construction

sunway associates