ADDITION / ALTERATION OF FIVE GUEST ROOMS AND THEIR ATTACHED TOILETS IN GROUND FLOOR OF PCDA GUEST HOUSE AT JAIPUR MIL STATION

Amount

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick in cement mortar (1:3) on any face of ceilling or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly palstered surface of wall and applying 2 mm thick putty to make the entire surface free from undulations and finally applying two coats of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying a coat of wall care putty on wall to make the entire surface free from undulations and finally applying two coats of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly palstered surface of ceiling and applying 2 mm thick putty to make the entire surface free from undulations and finally applying two coats of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

M&L for preparing old surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior acrylic emulsion paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying two coats of exterior acrylic emulsion paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking out shutters ,from the frame) , n exc 1.5 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutter exe 1.5 sqm but n exc 4 sqm (without taking off shutter from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down existing aluminium door single leaf exc 1.5 but n.exc 4.0 Sqm including taking down all members, sheet glass of any thickness, cleat, neosprene rubber beading and resecuring all section & tightening all joints including fixing new small cleats of suitable size, fixing L type cleats to secure joints of stiles and rails wherever necessary and refixing all members, sheet glass, aluminium cleat and new neosprene rubber beading and making the door shutter serviceable, including fixing on hinges and refixing in same position complete all as specified and directed by Engineer-in-Charge.

S&F 18 mm thick (one side decorative lamination and other side balancing lamination ) solid PVC board with cement solvent adhesive for shutters, kitchen cabinet/ cup board /partition wall/ wall cabinet incuding lipping to exposed surfaces with PVC strip as provided by manufacturer complete all as specified and directed by Engineer-in-Charge.

S&F for magnetic catcher of good quality made up of plastic and sheet metal plate of suitable size for fixing in cupboard of PVC shutter complete all as specified and directed by Engineer-in-Charge.

S&F in repair 125 mm dia oval shape SS handle fancy type bright finish or as approved complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel soft close auto hinge bright finish (Auto close concealed hinges) suitable for 18 to 20 mm thick shutter in any position complete all as specified and directed by Engineer-in-Charge.

S&F in repair basket/trolly soft close telescopic channel 50 cm long and 50mm width extruded MS galvanised with roller having ball bearing including drilling over stone/ply and PVC board etc complete all as specified and directed by Engineer-in-Charge.

S&F Continuous (piano) hinges,width of flaps 30mm (when open) mild steel, bright finish or electrogalvanised complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 (20mm graded stone agg) in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling) including weatherings, throating etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of brickwork or stone masonry including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar complete all as specified and directed by Engineer-in-Charge.

M&L for brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed by Engineer-in-Charge.

M&L RCC (nominal mix) 1:2:4 type B-1 (20mm graded stone aggregate) as in beams /Lintels etc complete all as specified and directed by Engineer-in-Charge.

M&L TMT bars 10mm dia and over cut to length, bent to shape required incl. cranking, bending and incl. mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to sides and soffits of lintels & beams including supports, overhangs, etc. with rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified. Note:- 10mm wide and 75mm deep joints shall be made at 3 mtr interval and at each corner the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in sub base of floor etc complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slab and tiles of any description or thickness laid dry or laid dry and pointed in floor, aprons or as in slabs complete all as specified and directed by Engineer-in-Charge.

M&L for Granite 25 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed/back coat in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. stainless steel screws, all complete including making good disturbed portion with the cement mortar 1:4 or providing PCC 1:2:4 type B0 to fill of opening complete all as specified and directed by Engineer-in-Charge.

M&L powder coated (minimum thickness of Powder coating 50 micron) aluminium window and ventilator shutters, fixed/side hung or sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified and directed by Engineer-in-Charge. Note: Rate shall be inclusive of 4.8mm thick plain or tinted glass sheet for glazing etc.

M&L for powder coated (minimum thickness of Powder coating 50 micron) aluminium door shutters aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing,handles 2 Nos in each door, hinges anodised alumnium snap beading, screws etc complete all as specified and directed by Engineer-in-Charge. Note: Rate shall be inclusive of 4.8mm thick plain sheet for glazing etc.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

S&F for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

S&F rolled mild steel for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410-W (Gde?E- 250) quality A complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces over 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing),removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic joint free coloured tiles 7-8 mm thick (square or rectangular)area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floors etc.. Set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic joint free coloured tiles 7-8 mm thick (square or rectangular)area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified ceramic coloured tiles (of approved dark shade) of size 600x 600mm, 9 to 10 mm thick in floor, set & jointed in neat cement slurry including a layer of screed bed 15mm thick in cement mortar 1:6 and pointed in coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-Charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface including washing and rubbing down with water and laying 25 mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement over the existing roof with WPC as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge.

M&L for water proof treatment to RCC Roof comprises the following complete all as specified and directed by Engineer-in-Charge :- (a) Applying High build elastomeric waterproofing coating based on aliphatic polyurethane, cold applied with spray/brush applicatiion, membrane with an elongation of 350% and crack bridging abillity of 2mm as per ASTM D 412. The system including final base preparation, single coat of single component PU based primer and applying Berger HS Elastoseal or equivalent brand of Sika/ Asian paint/ IWL in two coats to achieve a min thickness 1.2mm etc complete all as per manufacturer specification. (b) Necessary gurantee for 5 years shall be submitted by the contractor Make : SIKA/ASIAN Paints/IWL/Berger Paints.

S&F rotational moulded polye?thylene water storage tanks of capacity 500 litre (cylindrical vertical with closed top) hoisted and fixed in position inclding dismantling old unserviceable water tanks complete all as specified and directed by Engineer-in-Charge.

S&F for steel water tubes, 15mm diameter medium grade galvanized, with all fitting and fixed to walls and ceiling or laid in floors including taking down steel tubing and connections complete all as specified and directed by Engineer-in-Charge.

S&F for steel water tubes, 20mm diameter medium grade galvanized, with all fitting and fixed to walls and ceiling or laid in floors including taking down steel tubing and connections complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F for in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 110mm bore including taking down of existing pipe complete all as specified and directed by Engineer-in-Charge.

S&F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 75 mm bore including taking down of existing pipe complete all as specified and directed.

S&F for PVC (SWR) bend of any radius of 110mm bore including taking down of existing bend complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bend of any radius of 75mm bore including taking down of existing bend complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bend provided with access door of any radius of 110mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC ( SWR ) single junction (single ' T ') equal or unequal provided with access door of 110mm bore complete all as specified and directed.

M&L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) Note - (i) Qty of ploymer to be used 15% by weight of the cement or as per manufacturer instruction (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required.(iv) Keep the surfaces moist using water fog for 5 to 7 days etc complete all as specified and directed by Engineer-in-Charge. (v) Rate shall be inclusive of all necessary scaffolding for building height one storey complete all as specified and directed by Engineer-in-Charge. Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as directed by Engineer-in-Charge

M&L in repair for 100mm dia Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75mm complete all as specified and directed.

S&F for vitreous China full stall urinal flat back, size of 530x 340 x 360 mm /375mm x 390mm x 590mm white or equivalent (minimum) size, with rating and union for discharge pipe including 15mm bore chromium plated Push tap, 450mm PVC connector, coupling and waste pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair fancy type aluminium anodised curtain rail fancy type 20mm dia all as specified and directed.

Supply & fix in repair fancy type brass chromium plated side holder/ bulb/brackets for curtain rod all as specified and directed

Dismantling Plain FRP sheet from roof covering complete all as specified and directed by Engineer-in-Charge.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for High density polyethylene pipes(HDPE) of 50mm bore of pressure rating 6 kgf/cm2 laid in trenches and connecting with floor trap including reducer if any required complete all as specified and directed by Engineer-in-Charge.

S&F cast iron soil, waste and vent spun pipes of 75 mm bore in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium die cast door closer hydraulically regulated,designation No. 3,universal type, suitable for door shutters upto 1000 mm in width complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.. any thickness incl cover fillets etc complete all as specified and directed by Engineer-in-Charge.

M&L for PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid(size 605 x 605 mm) made of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre as specified and directed.

M&L 25 mm thick PCC Flooring using cement concrete 1:2:4 type B-0 using 12.50 mm graded aggregate below floor tile as in levelling course all as directed by Engineer-in-Charge.

S&F for factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet (colour and shade as approved ) on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification complete all as directed and specified

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet and edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S& F aluminium alloy ,anodized sliding door bolt with hasp and staple and fixing clips of sheet , cast or extruded section , and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm , fixed in repairs all as directed by Engineer-in-Charge.

S & F extruded aluminium anodised alloy handles, fabricated type, size of handle 150 mm all as directed by Engineer-in-Charge.

S&F aluminium ,anodized 200mm long barrel tower bolts of extruded section all as directed by Engineer-in-Charge.

S&F for butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge.

M&L for PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repairs fancy type CP angle cock 15mm dia cast coper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repairs 15 mm dia bore CP Central Hole Basin Mixer with Regular Spout without Popup Waste System with 450mm Long Braided Hoses, 20mm Cartridge Size etc as provided with manufacturer complete all as speciifed and as directed.

Supply and fixed in repairs 15 mm dia bore Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges etc as per manufacturer complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair 15 mm dia bore CP bib cock 15mm dia with crutch handle or butterfly hand with wall flange etc as per manufacturer specifiecation complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Overhead Shower 105mm Round Shape Single Flow with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System etc as per manufacturer specification complete all as specified and directed by Engineer-in-Charge.

S&F in repair Toilet Roll Holder with Stainless Steel Flap etc as per manufacturer specification complete all as specified and directed by Engineer-in-Charge.

S&F in repair Towel Rack 600mm Long Without Lower Hangers but with 3 hooks, Stainless Steel complete all as specified and as directed.

S&F in repair Soap dish holder complete all as specified and directed by Engineer-in-Charge.

S & F in repair for Stainless finish Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook with N.R.V (Back Flow Preventer) complete all as specified and directed by Engineer-in-Charge.

S&F for corner glass shelf (with bracket or railing complete all as specified and directed by Engineer-in-Charge.

S&F in repair for CP towel ring round complete all as specified and directed by Engineer-in-Charge.

S&F 32 mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap with wall conection pipes & wall flange complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for concealed stop Cock 15mm with wall flange incl all fittings complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for table Top Basin, Size: 420x420x155mm vitreous china white or coloured including all fittings complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Rimless Single Piece WC With UF Soft Close Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories And Accessories Set, Size: 360x675x750 mm, S Trap- 300 mm etc as per manufacturer complete all as speciified and as directed.

Taking down carefully aluminium or copper point wiring with PVC casing or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls, floors, etc all as directed.

Taking down celing fan of any size, sealing cable end , dismantling blade and removing fan regulator any type & size and keepinig in safe custudy for reuse/deposite to MES store all as specified and directed by Engr-in-Charge .

Refixing of ceiling fans after required minor repairs such as replacement of capacitor,connector block, split pin nuts bolts etc and connecting up including provisioning of cable from ceiling rose or connector to fan and painting of ceiling fan complete with one coat of synthetic enamel paint by spraying after clearing of dust etc including filling cavity with filler complete all as specified and directed.

Supply and fix ceiling fan down rod 15mm dia 45/60cm long suitable for any type of ceiling fan all as specified and directed.

Taking down exahust fan of any size, sealing cable end , dismantling blade and removing fan regulator any type & size and keepinig in safe custudy for reuse/deposit to MES store all as specified and directed by Engr-in-Charge .

Taking down and dismantling geyser including connected accessories such as PVC connection pipe etc of any type or make,safely and refixing after oiling, greasing and servicing in serviceable condition duly painted by synthetic enamel paint of existing colour complete including pron of New PVC connection of appropraite size all as specified and directed including writing MES Nos.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes for mounting switches, sockets, fan regulator as required for one light point controlled by one switch.

All as per item No. 101 here-in-before but one fan/wall fan point controlled by one switch

All as per item No. 101 here-in-before but one exhaust fan point controlled by one switch

All as per item No. 101 here-in-before but one light point controlled by two, two way switch.

All as per item No. 101 here-in-before but One bell point controlled by on bell push button.

All as per item No. 101 here-in-before but One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular sunken boxes for mounting switxhes, sockets, as required for One socket outlet 6 amp controlled by one switch on the same board with other switches.

Note for item No 101 to 108 :- (a) The cost of Modular Metal flush box & modular cover plate colour and size as required at site and cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate and the make of modular plate shall be of the same brand as per Switch/Socket accessories

(b) Modular switch/socket accessories shall be measured & paid separately in respective item

S&F switch modular 1 way 6/10 Amps, 230 volts, 1 module.

S&F modular socket 6/10 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular switch 1 way 16/20 Amps, 230 volts, 1 module.

S&F modular socket 16/20 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular fan regulator 120 watts, 2-module AC 230 Volts.

S&F Modular bell push 6A 1 module.

S&F musical bell, AC, 230 volts, single pole.

S&F switch modular 2 way 6/10 Amps, 230 volts, 1 module.

S&F ceiling rose 3 pin (phase,neutral and earth) polycarbonate body complete.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper cable of size 2 x 6 sqmm drawing into and including rigid non metallic PVC conduit concealed in wall, medium grade not less than 25mm dia ISI marked ivory colour with all conduit fitting and fixing accessories and 6 sqmm FRLS multistranded copper conductor cable as continuous earth wire complete all as specified and directed by Engineer-in-Charge. Note :- 2 runs of 6 sqmm copper wire and 1 run of 6 sqmm copper earth wire alongwith PVC conduit shall be measured as 1 unit. Note2- Rate of Cutting chasing of exixting wall and making good of disturbed surface for concealed conduit shall be included in this item

All as per ser No 118 above, but 4x 6 sqmm copper wire and 1 x 6 sqmm copper earth wire in 32 mm dia PVC conduit.

S&F 20 amp, single pole and neutral socket outlet with 2 pole and earth metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for socket outlet with and including one number single pole 'C' series MCB 20 amp as required.

S&F in replcement MCB distribution board, powder coated, TPN , 415 volts, 8 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F MCB distribution board, powder coated, SPN , 240 volts, 8 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required .

S&F RCBO, rated current 40 amp, rated residual current 30 mA, rated voltage -415 V AC (3P+N) residual current off time <=0.3 sec standard : IS 12640(part2): 2001& IEC: 61009-2-1, breaking capacity- 10 KA, Endurance- electrical - 4000 operation , Mechanical-10000 operating, terminal protection - IP20 all as specified & directed.

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp all as specified & directed.

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Double pole 10 to 32 amp all as specified & directed.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised iron strip 32 x 6 mm earth lead by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 and cover with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore medium grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete. Note:- Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained.

S&F energy efficient recessed mounted LED luminaire suitable for 2'x2' grid ceiling with flat diffuser and lumen output of 3300 lumens 36 Watts.

S&F LED mirror light 12 watt of size 1/1.2 feet of metal and synthetic finish having worm or white light with good colour rendering (CRI>80) complete all as specified and directed by Engineer-in-Charge.

S&F PVC fresh air fan 250 mm sweep,230 V with louvers, fan motor and accessories complete including making connections complete all as specified and directed by Engineer-in-Charge.

S&F in replacement surface mounted LED panel of size 220mmx220mm, 12 watt 1500 lumen output having luminous efficacy >85 Im/W, 6500K, 50Hz, p.f. .0.90, CRI80, THD ,30%, 25000 burning hours including making connection complete all as specified and directed by Engineer-in-Charge.

UNIVERSAL INFRAPROJECT PVT LTD (BID ID -3134714)

PUSHPA G ENTERPRISES (BID ID -3126925)

JAGDAMBA CONSTRUCTION COMPANY (BID ID -3125990)

S.R.Enterprises (BID ID -3134348)