SPECIAL REPAIR TO BLDG NO ET-26 AT AGE (I) PACHMARHI

Amount

Dismantling of floor, walls, roof tiles including bedding but backing and rubbish off permises all as specified.

M&L for 10mm thick Light shade vitrified ceramic tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified & directed.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 for laying of floor tiles as directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm and not exceeding 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete.

M&L for glazed ceramics coloured tiles of size 450x300x7mm thick in vertical surfaces such as skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces.

M&L for 10 mm thick randering in cement mortar 1 : 4 for fixing of wall tiles complete all as specified.

Demolition of cement concrete(unreinforced) in ground floor and paving n.exc 15 cm below or above ground level.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.

Mirror polish on kota stone where ever required to give high glossy finish over exsiting floor.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed

M & L 20 - 25 mm thick machine cut Kota stone slab in flooring or treads single piece of steps over and including 20mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above.

Description same as per item No 11 above but as in skirting or vertical surfaces including 10 mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete.

M&L Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) all as specified

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L 15 mm thick rendering on fair faces of bk/concrete surfaces in CM (1:6) finished even and smooth (without using extra cement ) complete all as specified.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete. Note : Liquid WPC will be measured and paid separately.

Supply only liquid water proofing compound , ISI marked.

M & L for preparation of surfaces of wall & concrete and applying 1 mm thick wall care putty including preparation complete.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of weather proof antifungal paint exterior emulsion Apex paint over & including one coat of primer complete all as specified and directed.

M&L for preparation of old plastered or decorated surfaces of wall and applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M&L preparation of old plastered or decorated surfaces of wall and applying two coats of weather proof antifungal paint exterior emulsion Apex paint over & including one coat of primer complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down Chowkhats or frames exc 1.5 sqm not e xc. 4 sq. m each with shutters (without taking off shutters from the frames)

S&F 2nd class hard wood plain, solid, straight, chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete.

S&F 35mm thick factory made plain framed, panelled door shutters (two panel) of IInd class hard wood rail and styles with lock rail and panel of 9 mm BWP commercial ply. The size of rail and style as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides, supplied and fitted to chowkats, complete all as specified and directed.

M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.50 mm (section No 20831), bottom size 92x31.75x1.50mm (section No 20832) and shutter top & bottom of size 40x18x1.55mm (section No 20736) and sides (handle) of size 40x18x1.55mm (section No 20738) and lock side shutter frame of size 40x18x1.45mm ( section No 20737)" with including and fixing rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including & fixing stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and including and fixing 5mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion all as specified and as directed by Engr-in-Charge.

S&F aluminium powder coted ventilator louvers type frame top and bottom of size 31x42x1.60mm(sec no-20558) rectaular tube of size 40x20x2 mm (sec no-14019 and middle verticalof size 42x46.20x1.60mm sec(20560) and clip for fixing wiremesh and glass of size 19x17.30x0.90mm (sec no-19360)thick including and fixing stainless steel wire cloth 0.36mm niminal dia of wire and 1.40mm average width of aperature and fixed with stainless steel wire staples and supply and fixing 5mm thick louvers with blades of 100 mm heavy duty with neccessary rubber beading ,gasket etcincluding necessary plaster, painting ,cill and making good to disturbed portion all as specified and directed by Engr-in-Charge

S&F aluminium anodised grill of 7.00 mm dia squares rectangular triangular circular shape aperture n.exc 7.00cm in length or width fixed with H or F channel.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube supplying & fixing in opening as per specified & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F in repair Harrison rails, anodised aluminium alloy , chromium plated with fixing brackets, stops, rollers et

S&F for sliding door bolt of Aluminium alloy anodised 250 mm complete

S&F Butt hinges (ISI marked), medium weight, cold rolled mild steel of size 100 mm.

S&F 200 mm long aluminum anodised barrel tower bolts of extruded section as specified.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed all as spd.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Dismantling PVC water tanks Exc 250 ltrs but not 500 ltrs including taking down of float valve and removing from site complete.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-1991 complete.

S&F in repair ball valve/float ball high pressure of PTMT 20mm with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed minimume weight 210 gm etc all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing.

S&F in repair bib tap 15 mm bore fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in repair of stainless steel soap dish, of standard size and shape complete.

S&F in repair vitereous china wash basin, white flat back, size 550x400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, incl 32 mm dia brass CP waste fittings (coupling) including 32 mm waste pipe.

Supply only 15mm dia pillar taps cast copper alloy chromium plated ,screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts screwed for iron pipe (bore of pipe 15mm)

S&F in repair vitreous china wash down water closet pan (Pedestal pattern)white including fixing bolt and plastic water closet seat white closed pattern with flat bottom cover with MS chromium plated hinging devices to matching colour.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S & F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

Supply only PVC connection 15mm size with PTMT nut of length 450mm

Taking down AC/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100/75 mm dia pipe.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

M/L PVC(SWR) bend of 110mm dia of any radius etc complete all as specified and directed

M/L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 75 mm dia

S&F PVC (SWR) multi floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete.

M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying one coats of synthetic enamel paint complete.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying one coats of synthetic enamel paint complete.

Dismantling timber scantlings as in framed work 40 sq. cm and over in section, in any position

S&F for MS framed works as in trusses, purline, rafters, column square/rectangular, round or angle section, fixed with and including iron cleats or other connected plates flate iron wind ties etc incl bending of MS section as requried omplete all as specified and as directed.Fe-410 gd 250

Dismantling of Asbestos cement sheet ( corrugated, semi corrugated etc) in roof covering

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws as specified

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridge,hip,valley,gutter of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified ®

M&L for 100mm thick PCC, type D2 (1:4:8) using 40mm graded stone aggt in paving complete all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors glossy finished with grey cement and pigment and including screed bed or bedding layer of cement mortar(1:4) 15 mm thick for laying floor finishes

M& L for 1.25 mm thick of 150 mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges

S&F for Drop ends (for spigot or socket ends) or nozzles of dia 150 mm

S&F for Stop ends (for spigot or socket ends) of dia 150 mm

Dismantling of ceiling board with fittings and any description including cover fillets as directed.

M&L for suspended false ceilling comprising of 4 mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sourrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to centre including hangers 6mmm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long complete all as specified.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE (I) Pachmarhi complete all as specified and as directed.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE (I) Pachmarhi complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for One light point controlled by one, one way switch 5 Amps

As per item No 86 but for One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

As per item No 86 but forOne 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

As per item No 86 but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

As per item No 86 but for One bell point controlled by one, bell switch 5 Amps

Description all as per item No 9 here in before but using 2.5 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathed as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No 9 here in before but using 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathed as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete.

S & F for modular switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for Bell push modular 6 Amps single module complete all as specified.

S & F for lamp holder, PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

S & F for water heater storage type (Geyser) vertical/ Horizental type as per site requirement with inner container of capacity 25 ltrs, electrically operated, AC 230 Volts,BEE 5 star rated, ISI marked including 04 Nos of hold fashner nuts required suitable size fixed in brick wall, PVC connection pipe hot & cold for Officers JCO's and OR Md Accn complete all as specied and as directed

S & F for Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make complete all as specified and directed

S & F for LED tube light fitting 2 feet x 10 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and as directed.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

S&F energy efficient recessed mounted LED luminaire 36 Watt suitable for 2'x2' grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable in renewal of any type luminaire as required.

S&F for ceiling fan, 230 volts, 1200mm sweep with service value of the fan shall be greater than 6.1 as per BIS with necessary accessories and electrical connections from ceiling rose to fan terminal complete all as specified and as directed

Dev Enterprises (BID ID -3479641)

M/S RAKESH TRADERS (BID ID -3479818)

GHASI RAM SAHU (BID ID -3473599)

MODI CORPORATION (BID ID -3474720)

SUBIR KUMAR ROY (BID ID -3478437)