SPL REPAIR TO BLDG NO T-39 AND SPL REPAIR TO LT PANEL AND CONNECTED WORK UNDER AGE B/R-I AND AGE E/M AT GE BABINA CANTT

Amount

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth and not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Excavation in trenches exceeding 1.5m wide and not exceeding 3m in depth and not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40 mm stone aggregate as in foundation filling and mass concrete ,sub base of flooring etc. complete all as specified and as directed.

M&L brick work with fly ash 'bricks (FASB) confirming to IS 12894, of strength M-10 straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed.

M&L brick work with fly ash 'bricks (FASB) confirming to IS 12894, of strength M-10 straight or curved on plan exc 6m mean radius built cement mortar 1:4 in half brick thick walls complete all as specified and as directed.

M&L renderig 15mm thick in cement mortar 1:6 on other than fair faces of brick or concrete surface of wall rendering is to be finished even and fair with out using extra cement complete all as specified and as directed.

M&L rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of wall rendering is to be finished even and fair with out using extra cement with water proofing compound etc complete all as specified and as directed.Note:- Water proofing compound shall be measured and paid seperatly.

M&L renderig 5mm thick in cement mortar 1:3 on fair faces of concrete surface of ceiling is to be finished even and fair with out using extra cement complete all as specified and as directed.

M&L 40 mm thick damp proof course in cement concrete 1:2:4, type B-0 (using 12.5 mm stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

M&L for hardcore of broken stone or boulders gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C1 ,using 20 mm graded crushed stone aggregates as in plinth protection/path laid in alternate panel , joint filled with bitumen 85/25 , surface finished even and fair complete all as specified and as directed. Note : The cost of materials for forming and filling joints deemed to be included in the unit rate quoted by the tenderer.

Supply only integral water proofing compound complete all as specified and as directed.

M&L prepation of newly plastered surface of wall and applying three coat of white wash complete all as specified and as directed.

M&L prepation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L providing reinforced cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate as in slab supported on walls, beams in roof etc complete all as specified and as directed.

M&L providing reinforced cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate as in beam, cantilevers, lintels over 1.5 m span etc complete all as specified and as directed.

M&L form work to soffits of suspended slab and similar works complete all as specified and as directed.

M&L form work to edges of concrete flat, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and as directed.

M&L TMT bars 8 mm dia cut to length, bent to shape required incl cranking, bending spirally for hopping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending spirally for hopping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L TMT bars 5 mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders, binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L Precast Cement Concrete 1:2:4 type B1 (using 20mm graded stone agg) as in but in landings, cover slabs (for manholes, drain cover etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face set in CM 1:6 complete all as specified and as directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate)as in sub base of floor complete all as specified and as directed

M&L non skid ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry and pointed in colour cement to match as in floor including 15 thick cement mortar screed bed 1:4 complete all as specified and as directed

M&L glazed ceramic colour tiles 300mmx600mm x7mm thick set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as skirting/dado including 10 mm thick rendering/screeding in cement mortar 1:3, complete all as specified and directed

S&F framed work as in door or gates of angle section including necessary welding, drilling etc complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail,paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as directed and specified by Engineer-in-Charge.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube etc complete all as specified and as directed.

Supply and fix 100mm size mild steel butt hinges medium weight, cold rolled complete all as specified and as directed by Engr-in-Charge.

S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified and as directed.

Supply and fix 200mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

S/F 150 mm size Aluminium handles, cast type, anodised and fixed of approved make & ISI marked complete all as specified and as directed.

Supply and fix 300 mm long aluminium alloy anodised sliding door bolts with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

S&F 20mm Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed

S&F, jointing and testing 15mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for the following sizes , the rate also include cutting through walls floors complete all as specified and directed.

S&F, jointing and testing 20mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for the following sizes , the rate also include cutting through walls floors complete all as specified and directed.

S&F 15 mm bore stop valve (angle cock) cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union and fixed complete all as specified and as directed.

S&F 15mm bore bib taps cast copper alloy fancy type chromium plated screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F 15mm dia pillar taps cast copper alloy with capstan heads, cromium plated screwed down high pressure with or without lettered Hot or Cold with long screw shanks abd fly -nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F 10 ltr capacity PVC low level flushing cistern white, ISI marked make as specified with inlet, float valve and handle including breacket with 32mm dia PVC pipe 600mm long complete all as specified and directed

S&F vitreous china squatting pan 'ORISSA PATTERN ' size 580mmx440mm 'white with integral foot rest (excluding flushing cistern and flush pipe ) with 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe anti syphonage pipe etc complete all as specified and as directed

S&F vitreous china wash hand basin, white flat back, size 550mmx400mm fixed on and including cast iron cantilever brackets, 32mm dia brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and as directed . Note: pillar tap shall be measured as supply only under respective items

S&F PVC connection 15mm dia and 450mm long with both ends brass fly nut complete all as specified and as directed (Make Prayag/Polytuf)

S&F PVC floor trap size 75mm dia out let with grating including connection to waste pipe with cement jointing complete all as specified and directed

S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints laid in trenches complete all as specified and as directed.

S&F PVC (SWR) pipes 75mm dia single sockted in any length with rubber ring joints laid in trenches complete all as specified and as directed.

S&F PVC (SWR) bends 110 mm bore of any radius complete all as specified and as directed.

S&F PVC (SWR) bends 75mm bore of any radius complete all as specified and as directed.

S&F PVC (SWR) junction single, (single T) equal or unequal 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110 mm complete all as specified and as directed.

S&F precast cement concrete louvres and jallies of cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick (measured solid) and set in cement mortar 1:4, including all mouldings, complete all as specified and directed.

S&F 500 litre cap rotational moulded polythelene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part - I including S and F of 20mm dia Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210gms

M&L for 150mm bore reinforcement concrete pipes, class NP-3 laid and jointed complete with collers complete all as specified and as directed.

M & L cement concrete bed to 150mm dia drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate complete all as specified and as directed.

Dismantling timber scantling , framed /un framed work of 40 sq. cm and over in section in any position complete all as specified and directed.

S&F mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 with and including one shop coat of zinc chrominium primer paint complete all as specified and directed.

S and F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as specified and directed.

S and F of framed work as in doors orgates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L two coat synthetic enamel paint over one coat of red oxide primer on new steel surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of Brickwork of stone/boulder masonry, build in lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articlesl etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc incl racking out joints hacking for key and scrabbing down with water etc complete all as specified and directed.

M&L renderig 15mm thick in cement mortar 1:6 over fair faces of of brick or concrete surface of wall rendering is to be finished even and smooth without using extra cement complete all as specified and directed.

M & L preparing of new surfaces and applying two coat of white wash on walls complete all as specified and as directed.

M & L preparing surfaces of wall by complete removal of existing treament and applying two coat of white wash on walls complete all as specified and as directed.

M & L for complete removal of existing treament and applying two coat of cement base paint over a coat of alkali resistant priming paint on external surface complete all as specified and as directed.

Demolition of cement concrete (unreinforced )in ground floor and paving n,exc 15cm thickness below or above ground level)complete all as specified and as directed

M and L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including Screed bed or bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor finishes with CM (1:6) complete all as specified and directed.

M & L for Kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15 thick Rendering cement mortar 1:6 complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description any type all as specified and as directed.

S & F for Mild steel, plain, black sheet 1.6 mm thick in wall cladding, steel gates and similar work, cut tosize, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F 1.25mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275and all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each etc complete as directed.

S & F in repair steel window with Z sections , side hung shutters including Box type hinges with steel handle peg stay, glazing bar, dovetailed or welded for recieving glass after and including taking out unserviceable steel window complete all as specified and directed.

S & F in repair steel window with Z sections , side hung shutters including Box type hinges with steel handle peg stay, with out glazing bar, dovetailed or welded for recieving glass after and including taking out unserviceable steel window complete all as specified and directed.

S & F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squareb n. exc 0.50 sqm in each plane complete all as specified and directed.

M&L framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of a-pertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed

Taking down carefully unserviceable aluminium point wiring (light, fan, socket or power) complete with fitting such as switches, ceiling roses, lamp holders, sockets, fan regulators, wooden terminal box plastic laminated sheet cover from TW battens including TW batten or drawing from existing conduit removing including TW batten all as specified and as directed by Engr-in-Charge.

Taking down carefully existing wooden board , Main switch, MCB DB boxes with MCBs, sheet metal boxes, cut out, etc of any size any capacity from boards complete all as specified and as directed.

Taking down carefully sub main wiring / service connection twin core from wall / LT pole of any size of Aluminum with wooden batten and or through rigid conduit including GI wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed.

M & L for concealed point wiring for one light point controlled by one switch complete with PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed .

Description same as per item No 90 above but one fan point controlled by one switch & regulator.

Description same as per item No 90 above but One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

Description same as per item No 90 above but One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

Description all as per item No 90 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with 2.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F switch piano flush button type 5 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp flush type complete all as specified and as directed.

S&F switch piano flush button type 15 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and as directed.

S&F ceiling rose,surface bakelite 63 x50mm three terminals complete all as specified and as directed.

S & F Sheet metal enclosure double door concealed suitable for distribution board when MCB to be used having 100 Amp rated bus bar 8 ways 240 volts complete all as specified and as directed.

S&F MCB single pole and neutral 40 Amp/63 Amp 240 V ,10KA , 'C' series, connected with copper lugs complete all as specified and as directed.

S&F Rigid non-metallic PVC conduit not less than 25mm dia(external) ISI marked concealed and including cutting necessary chases on wall/ceiling surface for drawing of conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 using 40 mm stone aggregate as in foundation filling and mass concrete including form work for poles/mass concrete at sub station etc. complete all as specified and as directed.

S&F exhaust fan, copper binding, steel body AC, Single Phase, 230V of size 300mm sweep, 1400 RPM with blades and frame and louvers including all arrangement of making holes in wall, making good and finishing of disterbed surfaces to match with existing surfaces complete all as specified and as directed.

Supply and lay river bed sand free from sharp materialsa for Sand cushioning for cables 8 cm below the cable and 15 cm above the cable all as specified and directed .

Supply and laying GI pipe 50mm bore "LIGHT GRADE" in trenches, under floors, roads, along poles for protection of cables, including sealing ends complete all as specified and as directed.

Supply,laying connecting and testing in replacement of cable XLPE insulated,screened,PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 V grade with multi stranded aluminium conductor of size 95 sqmm 3.5 core as per IS 7092 Pt-I complete all as specified and as directed.

Supply,laying connecting and testing in replacement of cable XLPE insulated,screened,PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 V grade with multi stranded aluminium conductor of size 25 sqmm 4 core as per IS 7092 Pt-I complete all as specified and as directed.

S&F MCB single pole 6 to 32Amps 240 V,10KA, 'C' series, connected with copper lugs complete all as specified and as directed.

S&F MCCB 4 pole, 415V, AC , 3 phase, 50 HZ, breaking capacity 16 KA with fixed thermal and fixed magnetic setting of capacity 125 Amps 100% ICU complete all as specified and as directed.

Supply and laying un-reinforced precast.concrete cable protection cover of class LV, type-1, flat size 250mm x 150mm x 40 mm, factory made of specified make , complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts , wells, cesspit, manholes, pipe lines, pier holes etc n exc 10Sqm on plan and n exc 1.5m in depth & getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40 mm stone aggregate as in coping of poles including necessary form work etc. complete all as specified and as directed.

S & F Lamp holder,PVC/Urea type with back plate suitable for batten fittings complete all as specified as directed

Supply, laying and jointing in replacement of GI pipe 100mm bore "LIGHT GRADE" in trenches, under floors, roads, along poles for protection of cables, including sealing ends complete all as specified and as directed.

S&F LED security/street light fittings1x35W LED 5700K energy saving and envoiremental frendly long life versatile pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 luminaire with high power LED as light siurce and electronic driver suitable for pole dia 35mm including 35mm dia light grade tube bracket, bend to shape 1.80m long with two numbers clamp of size 50mmx6mm with nuts, bolts, washers etc including connection with 1.5Sqmm two single core PVC insulated and PVC sheathed cable stranded copper conductor upto ceiling rose and fixing on wall /pole complete as ditrected by Engineer in Charge. Make: Bajaj Cat Part No BRLEP20WLEDWH or equivalent make as specified in Appendix B to particular specification.

S & F 9W/10W LED retrofit lamp B-22 holder base with polycorbonate body and aluminium heat sink complete all as specified as directed. Make C&S Cat No LTHPLEDLAMP7W/B22 or equivalent make as specified in Appndx 'B' to PS .

M&L for concealed sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6 sqmm FRLS, 1100 Volts grade cable drawn into conduit (Existing / new) including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete all as specified and as directed. Note:- (a) Two runs of 6 sqmm cable and one run of 6 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) New conduit and conduit accossories shall be measured separately.

Supply and fixing in repair 22W LED 6000k Decorative ultra slim linear LED fitting fixture with extruded polycarbonate ,environmental friendly ,energy efficentinterated driver and 22watts lamp fitted including wiring upto and terminal into ceiling rose complete all as specified and directed by Engr-in- Charge.

S&F concealed three phase neutral industrial socket with plug and socket in sheet metal enclosure of 63 Amp capacity having 100 amp rated bus bar including 63 Amp TPN MCB 'C' series complete all as specified and directed by Engr-in- Charge.

Supply, installing, testing and commissioning, factory made and tested ,CPRI type tested LT feeder pillar, outdoor type floor mounted , suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber duly insulated The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15 mm CRCA MS sheet and LT panel shall bemounted on angular frame work of 50x50x5mm thick angle iron base frame, minimum 60 cm hight and fixed with PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in foundation for fixing panels, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, both side opening type, with aprons for cable entry, with double door shutter and locking arrangement and consisting of the following all as specified including taking out old feeder pillar and taking out LT cable from loop for connecting in new panel and necessary excavation etc and consisting of the followings: - (Loc - Near MAP Qtr No P-37) (a) Aluminium bus bar four strips 300 Amps ,415 volts,fixed on epoxy insulated with panel fixed horizontally, duly insulated with heat shrinkable sleeves in colour code - 01 Set. Incoming:- (b) MCCB, 04 Pole, 200 Amps with ultimate breaking capacity Icu- 25 KA at 415 volts , adjustable type with thermal and magnetic settings conforming to IEC 60947 Part-I/IS-13947 Part-I - 01 No (Ics=Icu=100%) Outgoing:- (c) MCCB, 04 Pole, 63 Amps with ultimate breaking capacity 10 KA at 415 volts with fixed thermalsettings conforming to IEC 60947 Part-I/IS-13947 Part-I - 07 No, (Ics=Icu=100%)

(d) Digital Volt meter degital type 0-500 volt - 01 Set . (h) Digital Ammeter degital type 0-500 Amp - 01 Set (j) Indication lamps R,Y,B LED type – 1 set:- (k) Internal wiring with suitable size of PVC insulated stranded copper conductor cable duly crimped with copper lugs & ferruled and aluminum strips for MCCB's. (l) Suitable size cable glands - 08 Nos. Note :- Panel drawings & make of MCCB will be submitted by contractor for approval from Accepting Officer before ordering the panel

M&L for earthing complete with galvanised steel earth plate electrode of size 600X600X6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.50 mtr below the ground level connected to galvanised iron strip of 32 x 6 mm as earth lead by means of bolts nuts check nuts & washers of galvanised iron or steel ,surrounded by charcoal of coke and salt, protected by GI pipe 40 mm bore (light grade), water pipe 20mm bore GI medium grade with funnel and wire mesh,and making chamber of PCC (1:4:8) type D-2 using 40 mm graded stone aggregate and coping shall be in PCC(1:3:6) type C-1 using 20 mm graded stone aggregate, 50 mm thick cover of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate, reinforced with 8 mm dia TMT bars @ 80 mm c/c boath ways including excavation and earth work and removal of surplus soil to distance n exc 50 m complete all shown in electrical plate No 3 of SSR part- 2010 complete all as specified and directed. Note :-(i) The cost of GI earth lead & G I pipe of 7.50 mtr length for protection of GI wire and excavation work for pit shall deemed to be included in this item. (ii) Earthing test will be carried out and if desired result not achieved and the earthing will be redone to achieve desired result without any extra payment.(iii) Charcoal dust and common salt upto 1.5 meter depth shall be filled in layers of 15 centimeters all around the earth plate.

Supply, installing, testing and commissioning, factory made and tested APFC panel of capacity 300 KVAR outdoor type floor mounted , suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system having bus bar chamber duly insulated. The APFC panel shall be dust and vermin proof, IP 65 class protection and made of 3.15 mm CRCA MS sheet and panel shall be mounted on angular frame work of 50x50x5mm thick angle iron base frame, minimum 60 cm hight and fixed with PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in foundation for fixing panels, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, both side opening type, with aprons for cable entry, with double door shutter and locking arrangement and consisting of the following all as specified including taking out old feeder pillar and taking out LT cable from loop for connecting in new panel and necessary excavation etc and consisting of the followings: - (Loc - MAP Qtr transformer) (a) Incomer 630 amp - 01 Set (Each set consisting of) (i) MCCB, 03 Pole, 630 Amps 50 KA with EROM and spreaders - 1 Set (ii) LED phase indicators Aux supply 240 VAC - 03 Nos (iii) MCB 1 pole 6A 10 KA - 03 Nos (iv) Digital ammeter 1 phase CTR-/5A aux supply 240VAC - 01 Nos (v) CT 600/5A, CL-1.0, 5VA, Tap wound type - 02 Nos (vi) APFC relay 12 stage 1 CT Aux supply 415 VAC - 01 No (b)50 KVAR Bank - 04 Set (Each set consisting of) (i) MCCB, 03 Pole, 100 Amps 36 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 60 contactor - 01 No (iv)Heavy duty cylindrical capacitor 25 KVAR - 02 Nos (v) Auto manual switch - 01 No

(vi) LED indicator for capacitor switching indication - 01 No (c) 25 KVAR Bank - 02 Set (Each set consisting of) (i) MCB, 03 Pole, 63 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 30 contactor - 01 No (iv)Heavy duty cylindrical capacitor 25 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No (d) 15 KVAR Bank - 02 Set (Each set consisting of) (i) MCB, 03 Pole, 40 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 20 contactor - 01 No (iv)Heavy duty cylindrical capacitor 15 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No (e) 10 KVAR Bank - 01 Set (Each set consisting of) (i) MCB, 03 Pole, 32 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 12.5 contactor - 01 No (iv)Heavy duty cylindrical capacitor 10 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No

(f) 05 KVAR Bank - 01 Set (Each set consisting of) (i) MCB, 03 Pole, 20 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 8.5 contactor - 01 No (iv)Heavy duty cylindrical capacitor 05 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No (g) 03 KVAR Bank - 01 Set (Each set consisting of) (i) MCB, 03 Pole, 16 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC 5 contactor - 01 No (iv)Heavy duty cylindrical capacitor 03 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No (h) 02 KVAR Bank - 01 Set (Each set consisting of) (i) MCB, 03 Pole, 10 Amps 10 KA - 1 No (ii) MCB SP 6A - 01 No (iii) MOC-3 contactor - 01 No (iv)Heavy duty cylindrical capacitor 02 KVAR - 01 No (v) Auto manual switch - 01 No (vi) LED indicator for capacitor switching indication - 01 No. Note: - (i) Panels shall be commissioned and functional by authorized rep of manufacturer. (ii) 02 Years written warranty of manufacturer to be submitted by the contractor before payment of panel.

M&L for replacement of new generation energy saving and environmental friendly long life LED street light of cap 70W made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including taking down of old unserviceable street light any type/any capacity including replacement of twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from junction box to LED light throgh copper connectos all as specified and directed.

M&L for replacement of new generation energy saving and environmental friendly long life LED street light of cap 90W made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including taking down of old unserviceable street light any type/any capacity including replacement of twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from junction box to LED light throgh copper connectos all as specified and directed.

M&L for replacement of new generation energy saving and environmental friendly long life LED street light of cap 120W made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including taking down of old unserviceable street light any type/any capacity including replacement of twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from junction box to LED light throgh copper connectos all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

M/s Ravi Traders

M/S M S Constructions

M/S Chadha Brothers

Ms Vinay constructions

M/S Kharya Associates