WORK FOR I.T. CENTRE ALONGWITH HVAC and ALLIED WORK AT FOURTH FLOOR PARYAVAS BHAWAN BHOPAL

Amount

Providing and fixing U Baffle Aluminium panel ceiling of approved colour consisting of panel size 100 mm deep X 50 mm width using 0.7mm thick, panel length upto 4 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics. Panels shall be clipped to a baked enamelled Aluminium carrier of 30 mm wide x 47 mm high x 0.5 mm thick, Black Colour coated, one leg of the carriers with cut outs to hold the panels in a module of 100 / 200 mm. Panel carrier shall be suspended by means of threaded rod at a distance of 1.8 mtr c/c. Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, Exposed side with a full primer and finish coat on a Continuous Paint Line. Ceiling Finish above U Baffle Ceiling : Ceiling area above U Baffle to be painted in black colour before fixing this system. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffuses, columns etc. complete in all respect as per drawing and direction given by Engineer in charge.

Providing & fixing EURO pratik products of DECORIS series/CASA Series/3D wall art/ Designer wave board on 8mm thick ply (Century /Archidply/ Duro) on framework 50mmx50mm thick sal wood sections/second grade TW, placed at 600mm c/c in both the directions as per detail drawings. As directed by engineer in charge and architect.

Providing & fixing of Corian sheet for any surface design including all accessories and adhesive materials etc. complete in all respect as per direction given by Engineer in charge. (LG / SAMSUNG / DUPONT)

Providing and fixing painting work made out of canvass by acrylic /oil paint colours as per design with framing work etc. complete in all respect as per direction given by Engineer in charge.

Providing and fixing wall cladding complete including all material required for fixing etc. complete in all respect as per direction given by Engineer in charge.

Providing and fixing steel dustbin with cover and rubber base for water protection perforated design as per direction of Engineer in charge.

Providing & fixing of imported 3D wall paper with high resolution including all fitting with wastage(Spin Décor / marshell / Green)

Providing & fixing of plane washable wall paper high resolution including all fittings with wastage.(Spin Décor / marshell / Green)

ROLLER BLINDS:- Providing and fixing of roller blinds of washable fabric duly fixed with powder coated channel and clamps having nylon code for operation of approved color etc. complete in all respect as per direction given by Engineer in charge. (Vista / NBT /MAC/WINDOW TECH)

Providing & applying deco paints to wood work with required cleaning, rubbing, primer & surface and i/c covering of side partitions and glasses and after work all cleaning and finishing the surface etc. complete in all respect as per direction given by Engineer in charge. (Asian/ICI dulux/ Nerolac )

Providing and fixing CNC Design in cement ply complete with 18mm thick Cement ply including painting complete including all material required for fixing etc. complete in all respect as per direction given by Engineer in charge.

Providing and Fixing 35 mm thick Unitex Artificial Grass TF QH 35 3/8" Tufted Synthetic grass carpet for land scaping/ multi used field, straight yarn 100% PE Monofilament Anti UV fiber, tuffed weight 145 1600 g/sqm, total weight 2850 g/sqm, primary backing P.P. Double layer, layed over existing cement concrete floor with adhesive i/c cost of cutting, fixing etc. complete in all respect as per direction given by Engineer in charge.

Reception Table -Providing and fixing of Reception Table in two top one is 1.0m height 0.3m wide and second is 0.6 m wide . L 2.60 and 0.75m height made of 18MM BWP ply finished with 1 mm thick laminate, corian and 6mm X 2" T.W. edge beading, and 6mm X 1" beading for drawer and shutter edges of matching colour. Provision for two raceway trays & foot rest, wire manager etc. as per design all exposed edges to be finished with first quality Teak wood beading which is to be melamine polished/ pu coating. The rate shall include all necessary hardware like 3'' brass hinges, handles, drawer channels, etc complete in all respect as per drawing and direction given by Engineer in charge.

Providing and fixing of 12mm. Thick soft board for display in partition etc. complete in all respect as per drawing and direction given by Engineer in charge.

Providing & Applying ICI Dulux & other equivalent velvet toch pearl glo premium interior plastic emulsion paint smooth silky finish two or coat in desired shade with one coat of alkali block anti algi anti fungel primer with two coat of acrylic / cement base wall putty scraping rubbering etc complete.

Providing and fixing Designer bright finished brass handle 300mm in Toughened glass doors of M/s PANS make with product code PA-720,finish MAB,and size 530(L)*300(C.C) as approved by the architect including necessary fittings, labour,material etc.complete.

Supply and Installation of XBENCH Workstations: Single Workstation Sharing 1200*600*740 Legs:-The legs are 50x50 mm thick Square pipe made of 1.6 mm thick CRCA pipe duly powder coated. The powder coating thickness considered is 50 to 60 microns DFT.Tie Member:-The tie member should be 80x40 mm pipe structure made of 1.6 mm thick CRCA duly powder coated. The powder coating thickness considered is 50to60 microns DFT. Structure to fully welded with all arcwelding from in side eliminating manual finishing. None of the welding joints should be visible from outside. MAST:-The vertical and horizontal of the mast to made up of 1.6 mm thick CRCA bent into the C shape channel. The mast size to be conside 6 redas 500x105 mm for sharing back to back cluster. For non sharing cluster the Mast size is 230x105 mm.The mast coveris 0.7 mm thick galvanized iron sheet. The inner brackets are 3 mm thick CRCA.LEGSHOE/LEVELLERS:-The leg shoe is made up of 100% recyclable nylon 6. The shoe helps in mounting of levelers on the legs by eliminating any welding process. The levelers are made of Nylon 6 with M8 bolts insert moulded to take care of any floor undulation.BEAM:- MAKE : GODREJ / HARMANMILLER / WIPRO /FEATHERLITE / HAWORTH The beam is 1.2mm thick CRCA bent in the form of C channels with 3mm thick CRCA brackets.The bottom cover is made of 0.7mm thick GI sheet. All welding is from inside eliminating manual finishing. The beam acts as a main spine, stiffeners and also cable carrying race way thus eliminating use of extra material. The size of the beam is100mm height and depth of 445mm for sharing. In case of non sharing the size is 100mm height and 190mm depth.TABLE TOP:-TheTableTop is made of 25mm thick pre laminated particle board. The exposed edges of the table to pare sealed with 2mm PVC edge banding. The height of the table top from the ground should be 740mm. WIRE MANAGEMENT:-The vertical wire is carried through the mast and is carried in the horizontal direction by the beam which also acts as wire carrying member. The switches can be mounted on the beam below the table top.Provision for flip top box are patented DUO is also available for accessing wires from the table top. SCREENBRACKETS:-The screen bracket are dye-cast aluminum(LM-24) which is bolted to the table top through prefitted inserts.The inserts are all factory made to add rigidity and modularity in all aspects; making refitting and removal of screens sever all times possible. The bracket covers to be made of Poly propylene which is snapfitted to the original brackets. The same brackets can be used for both Glass and fabric Screens.This provides additional modularity while changing screen material at any given time without any major additional component. Product complies to ANSI/BIFMA : X 5.5-2014 1.1 1350x600

Mobile storage 400 x 435 x 583 - metal body with cushion top - Material Thickness 0.8 mm body, powder coating thickness 40 - 50 microns. mobile pedestal with Castors 40 mm dia, Standard Finish: Warm Grey. One Box & One drawer type pedestal. In-built flush handles for seamless look. Provision of cushion on top for Smart Seating solution. Anti-toppling mechanism for better stability. Drawer fixed on ball bearings. Provision for individual and central locking. MAKE : GODREJ / HARMANMILLER / WIPRO /FEATHERLITE / HAWORTH

LIVO 120 degree curvilinear workstation 1500x600x1500 with storage in middle (Single Seating) - Structural Support System: curvilinear workstations will generally be supported on a leg and beam based system. This is characterised by the use of combination of load bearing high grade extruted aluminium beams (HE 9) and Legs comprising of die cast (LM 24) connecting parts in conjunction with extruded aluminium sections to form a robust Frame type leg when joined together (ref. image as shown herewith). Benching or Linear workstations shall be constructed using high grade extruded aluminium sections in twin leg type construction with die cast end caps & levelers. The leg assemblies shall be finished with superior powder coat finish (60 DFT). Beam used shall be aluminum extrusion of HE 9 grade. Beam shall have T-Slots on all the faces for easy clamping of components. Beam shall also be with superior powder coat finish. Beam dimensions: (H) 50 mm x (W) 50mm. MAKE : GODREJ / HARMANMILLER / WIPRO /FEATHERLITE / HAWORTH Wire Management: The Vertical mast is made of CRCA sheet of 1.6mm thickness and dimension is 150mm W x 50mm D x 665mm H with M8 leveler with 30mm H adjustment. Horizontal raceway is made out of 1.5 mm thick aluminium extrusion & powder coated with a dimension of 120H and length equal to the table top size. Approximately 50-60 (5mm Dia) cables can be accommodated in the raceway channels.The electrical raceway can be provided below worktop & these are hinged raceway and switches are mounted on raceway below table top, on table top using using access flap. Privacy Screen: Fabric Screen (soft pin up / White board) with Aluminium frame (25mm thick) mounted on the beam, Height of Privacy Screen shall be 300/400mm. Provision for hang type marker shall be made available as an option in every workstation as per specification. Table tops: are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. Specially designed powder coated Aluminium die cast brackets hooked to the partition frame to support the tabletops wihtout any predefined position. Sealed edge in table top are with 2mm PVC imported edge banding. PVC edge banding are imported from Rehau or Dolken of Germany. MAKE : GODREJ / HARMANMILLER / WIPRO /FEATHERLITE / HAWORTH Legs : Legs are made up of a combination of Aluminium extrusion (6063 -T6) and aluminum die cast (LM 24) connectors which is hooked on to frame to ensure stability and fixing table top. Legs is fitted with a nylon foot of 100mm height with M8 leveler for level adjustment up to 30mm to accomodate floor undulation. Legs are avilable in both Incined and straight profile. Colour Highlighter : 7 colour highlighter available - Green, Yellow, Blue, Orange, White, Grey & black which goes in to the frame and legs namely - 50/25mm corner cap, leg cap & leg shoe band. Storage Unit : Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany Product complies to ANSI/BIFMA : X 5.6 -2016 PANEL SYSTEMS & ANSI/BIFMA : X 5.5-2014 DES / TABLE MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Cabin - Main Table - 1.80 X 0.75 Supply and Installation of Kingsley Premium main table of size 1800 X 750 mm completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer. Kingsley Premium return table of size 1350X450mm completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is in 25mm thk baord with 2mm PVC edge banding supported on 25mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets (Wipro Patented Squeezee) shall be provided on main or side table as specified by customer. Back Storage with OPENABLE SHUTTERS - 1050X425X1200MM with body made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Conference Table - Supplying and placing of Conference table with top Size 750 x 750 X 740 mm(per seater). Table Top :- The top of the table shall be made of 38 mm Composite MDF (25mm plain MDF board + 12mm plain MDF) with PVC membrane 0.4mm Thick PVC membrane foil using wrap around technology. The foil is pre-coated with PU layer for better scratch and wear resistance. 0.6mm balancing laminate on bottom surface. Understructure :- The legs of the table shall be 25 mm thk , post formed particle board with round edge. Modesty Panel :- The modesty panel of the table shall be 600mm high made of 18mm thk prelam particle board. Vertibrae fixed to worksurface from bottom side for entering wires The wire carrying is facilitated through the hollow space between plastic components. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Reception Chair and Workstation Chair - MB, S1 MECHANISM, FIXED ARMS, NYLON BASE, NYLON CASTORS Providing and fixing Executive Medium Back chairs with following DIMENSIONS:- Complete chair at normal height 1000mm., Complete chair when gas lift is raised 1100mm.Width and the depth of the chair is 625mm (w) x 575mm (d). BACKREST:- The outer frame of the backrest made up of injection moulded in black polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has auto contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P and upholstered with U foam. Lumber support size 160mm (W) x 90mm (H) at fixed position Backrest size 650mm (H) x 530 (W). SEAT:- The seat is made up of 12mm thick (7layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 495mm (W) x 510mm (D). Minimum and maximum seat height is 450mm and 550mm respectively. SEAT FOAM:- Foam made out of moulded polyurethane foam with the following properties: Density: 45 – 55 Kg/m3, Hardness: 15 – 20 Kgf, Compression set: 50% 10 Max, Tensile strength: 1.03, Tear strength (Min) : 2.0 N/cm, Resilience : 50% - 60%, Comfort / Indentation Hardness : 15.4 ARM REST:- FIXED ARM: (‘T’ ARM): The arm rest made up of injection moulded from block P.P. Seat Angle: 3-10 degrees, With back tension adjustment knob, Locking Positions: 1 position, can be locked & unlocked by lever, Tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002, Movements of Seat Pan & Back Support complies with BIFMA Section no 7.6 Table 21 Gas Lift: Meets DIN 4550 Class 3, Meets ANSI BIFMA performance standards, Tested for 1, 00,000 Cycles Caster:- Options for Nylon 50 mm, Complies to ANSI / BIFMA X 5.1 – 2002, Tested for 1,00,000 Cycles Base:- Type of Base - Nylon, Static Load as per ANSI / BIFMA X 5.1 2.2 – 2002 Clause 7 - 1134Kg, Pitch Circle Diameter - 640mm, Finish - Black Matt Armrests:- Armrest Option - Height Adjustable, Armrest Height from the seat - 180-260mm, Armrest Width excluding Armpads - 80mm, Arm pad length - 270mm, Arm pad finish - PP, Arm pad finish - PU, The above Arm rest comply with ANSI BIFMA X 5.1 -2002 Clause 13.4 Upholstery:- Available in Fabric - Wipro Delta Range Fabric: (Delta Orange / Delta Wine Red / Delta Black): Content: 100% Polyester, Weight:Abrasion: 80,000 Flammability: BS EN 1021-1 1994 (Cigarette) BS 7176:1995 (Low Hazard), Color Fastness to Light: 5+ [BS 1006 (1990)], Rubbing; Dry: Class 5 Wet: Class 4.5 MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH Arm rest size 280mm (L) x 85mm (W). Arm rest tested for 60000 cycles to be completed with the load of 40kg per arm. MECHANISM:- SYNCRO 1 Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 3°~10° and back tilting angle is 87°~106°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT:- Gas lift pipe diameter 50mm and has an Height adjustment stoke of 112mm. Gas lift tested for 1, 00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 4 and all applicable ANSI/BIFMA, EN performance standard. BASE:- The base is injection moulded in black 30% glass filled nylon and fitted with 5nos twin wheel castors. The base is 660 pitch circle diameter. The base is tested for static load of 1250kg. CASTERS:- The twin wheel castors are injection moulded in Nylon and diameter of castor 60 mm. the castors are tested for 100000 cycles as per ANSI/BIFMA X 5.1. TEXO SEAT FABRIC:- Fabric with the following properties :Content: 100% Polyester, Abrasion: <96,000, Flammability: Adheres to BS EN 10211 1994 (Cigarette) Adheres to BS 7176:1995 (Low Hazard), Color Fastness to Light : Adheres to : 3+ [BS 1006 (1990)], Rubbing : Adheres to Dry: Class 3 Adheres to Wet: Class 3, BACKREST MESH SPECIFICATION:- Mesh with the following properties :Content: 100% Polyester, Weight: 320 GLM, Abrasion: 80,000, Flammability: BS EN 1021-1 1994 (Cigarette)BS 7176:1995 (Low Hazard), Color Fastness to Light: 4.5+ [BS 1006 (1990)], Rubbing;Dry: Class 5 Wet: Class 4.5. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Cabin Main Chair - HB, S1 MECHANISM, 1D ARMS, NYLON BASE, NYLON CASTORS, FABRIC FINISH Providing and fixing Back Rest:- Back type - High Back, Seat to Backrest Height - 650mm, Backrest Height - 790mm, Backrest Width - 500mm, Backrest Construction - Ply+Foam, Finish - Fabric/Leatherite, Seat to Back rest height complies with BIFMA Section no 7.5.1 Table 21, Backrest width complies with BIFMA Section no 7.5.2 Table 21, Backrest is made out of 12 mm multilayer BWP ply. PU foam of 50 mm thickness Seat Rest:- Width Excluding Arms - 460-500mm, Depth including of Waterfall edge - 470mm, Min Seat Height - 440mm, Max Seat Height - 540mm, Finish - Fabric/Leatherite, *500 mm is width when 3D arm is used, Seat depth complies with BIFMA Section 7.2 Table 21, Seat width complies with BIFMA Section 7.3 Table 21, Seat Height Adjustment complies with EN1335 -1: 2000 Type A Seat Foam:- Made out of High resilience foam with the following properties: Density 58-61 Kg/m, (IFD) Indentation: Force Deflection 25% 21.5 Kgf/cm, Tensile strength 2.0 Kgf/cm, Tear strength 1.0 Kgf/cm, Resilience 60% Mechanism: Synchro 1 Position BIFMA Compliant Mechanism: Back Tilt: 87 -106 degrees, Seat Angle: 3-10 degrees, With back tension adjustment knob, Locking Positions: 1 position, can be locked & unlocked by lever, Tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002, Movements of Seat Pan & Back Support complies with BIFMA Section no 7.6 Table 21 Gas Lift: Meets DIN 4550 Class 3, Meets ANSI BIFMA performance standards, Tested for 1, 00,000 Cycles Caster:- Options for Nylon 50 mm, Complies to ANSI / BIFMA X 5.1 – 2002, Tested for 1,00,000 Cycles Base:- Type of Base - Nylon, Static Load as per ANSI / BIFMA X 5.1 2.2 – 2002 Clause 7 - 1134Kg, Pitch Circle Diameter - 640mm, Finish - Black Matt Armrests:- Armrest Option - Height Adjustable, Armrest Height from the seat - 180-260mm, Armrest Width excluding Armpads - 80mm, Arm pad length - 270mm, Arm pad finish - PP, Arm pad finish - PU, The above Arm rest comply with ANSI BIFMA X 5.1 -2002 Clause 13.4 Upholstery:- Available in Fabric - Wipro Delta Range Fabric: (Delta Orange / Delta Wine Red / Delta Black): Content: 100% Polyester, Weight:Abrasion: 80,000 Flammability: BS EN 1021-1 1994 (Cigarette) BS 7176:1995 (Low Hazard), Color Fastness to Light: 5+ [BS 1006 (1990)], Rubbing; Dry: Class 5 Wet: Class 4.5 MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Cabin Visitor Chair MB, S1 MECHANISM, 1D ARMS, NLON BASE, NYLON CASTORS, FABRIC FINISH Providing and fixing Executive Medium Back chairs with Back Rest:- Back type - Medium Back, Seat to Backrest Height - 500mm, Backrest Height - 630mm, Backrest Width - 490mm, Backrest Construction - Ply+Foam, Finish - Fabric/Leatherite, Seat to Back rest height complies with BIFMA Section no 7.5.1 Table 21, Backrest width complies with BIFMA Section no 7.5.2 Table 21, Backrest is made out of 12 mm multilayer BWP ply. PU foam of 50 mm thickness Seat Rest:- Width Excluding Arms - 460-500mm, Depth including of Waterfall edge - 470mm, Min Seat Height - 440mm, Max Seat Height - 540mm, Finish - Fabric/Leatherite, *500 mm is width when 3D arm is used, Seat depth complies with BIFMA Section 7.2 Table 21, Seat width complies with BIFMA Section 7.3 Table 21, Seat Height Adjustment complies with EN1335 -1: 2000 Type A Seat Foam:- Made out of High resilience foam with the following properties: Density 58-61 Kg/m, (IFD) Indentation: Force Deflection 25% 21.5 Kgf/cm, Tensile strength 2.0 Kgf/cm, Tear strength 1.0 Kgf/cm, Resilience 60% Mechanism: Synchro 1 Position BIFMA Compliant Mechanism: Back Tilt: 87 -106 degrees, Seat Angle: 3-10 degrees, With back tension adjustment knob, Locking Positions: 1 position, can be locked & unlocked by lever, Tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002, Movements of Seat Pan & Back Support complies with BIFMA Section no 7.6 Table 21 Gas Lift: Meets DIN 4550 Class 3, Meets ANSI BIFMA MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Conference Chair - MB - S1 - Fixed - Nylon base - Nylon Castors With Lumbar Support BACKREST: The frame of backrest made up of injection moulded in black nylon 6 and frame upholstered with mesh, Back rest Size 460mm (W) X 500mm (D). The back has flexible contoured lumber support for achieving comfortable seating posture. Lumber support inner and outer cover is made up of injection moulded in black nylon and upholstred with fabric. Lumber Support size 230 mm (W) X 100 mm (H). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT: The seat is made up of 12mm thick (7 layers) hot pressed plywood and moluded seat foam upholstered with fabric. Seat Size 455mm (W) X 480mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1. SEAT FOAM: Foam made out of moulded Polyurethane foam with the following properties: ARM REST: FIXED ARM ("T" TYPE): The armrest made up of injection moulded from black polypropylene. Armrest size 240mm (L) x 65mm (W). Armrest tested for 60,000 Cycles to be completed with load of 40Kg as per ANSI / BIFMA X5.1 MECHANISM: SINGLE POINT SYNCHRO MECHANISM: Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 3°~10°. and back tilting angle is 87°~106°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT: Gas lift pipe diameter 50mm and has an Height adjustment stoke of 112mm. Gas lift tested for 1,00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 4 and all applicable ANSI/BIFMA, BASE : NYLON BASE : The base made up of injection moulded in black glass filled nylon (GF 30%) and fitted with 5Nos twin wheel castors. The base is 658mm pitch circle dimeter. The base tested for static load of 1250 Kg as per ANSI / BIFMA X 5.1. CASTERS: NYLON CASTORS: The twin wheel castors are injection mouled in nylon and diameter of Castor 60 mm. The castors are tested for 1, 00,000 Cycles as per ANSI / BIFMA X 5.1. BEST RANGE: Seat Fabric with the following properties: Content: 100%Polyester. Weight: 340 GSM Abrasion: Over 30000 Flammability: Adheres to California Technical Bulletin117 Section E , part 1(CS191-53) Color Fastness to Light: Adheres to Grade 5 [ISO 105-B02:1997] , [GB/T8427-1998] Rubbing; Adheres to Dry: Grade 4- 5 [ATTCC8:2001] ,[GB/T3920-1997] Adheres to Wet: Grade 4-5 [ATTCC8:2001] ,[GB/T3920-1997]. Back Mesh with the following properties: Content: 100% Polyester Weight: 320 GSM Abrasion resistance: ASTM D4966 Over 30 000 rubs Flammability: Ca.117 Section E, Part I Cigarette test -Pass Color fastness to Rubbing: AATCC 8 Dry: 4 , Wet: 4 MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

3 Seater Sofa - 2065(L) X 850(W) X 760(H)MM Providing and fixing BIFMA Certified sofa, Frame Constructio- Kiln seasoned mixed meranti solid tropical hard wood, Seats Webbing:- 3" diagonal pattern webbing, Foam:- 7" Multilayered foams Having 4" of High Resilience-HD Foam and 3" of HD virgin PU Foam. BACKREST Webbing:- 2" elastic webbing, Backrest Foam:- 18D PU foam, Upholstery:- semi PU with layer of polyester polywadding, Stitiching:- Nylon Bonded thread, Glue - Sp4 from Pidilite, Legs - Solid kiln seasoned and treated Solid wood with melamine matt finish MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

2 Seater Sofa - 1525(L) X 850(W) X 760(H)MM Providing and fixing BIFMA Certified sofa, Frame Constructio- Kiln seasoned mixed meranti solid tropical hard wood, Seats Webbing:- 3" diagonal pattern webbing, Foam:- 7" Multilayered foams Having 4" of High Resilience-HD Foam and 3" of HD virgin PU Foam. BACKREST Webbing:- 2" elastic webbing, Backrest Foam:- 18D PU foam, Upholstery:- semi PU with layer of polyester polywadding, Stitiching:- Nylon Bonded thread, Glue - Sp4 from Pidilite, Legs - Solid kiln seasoned and treated Solid wood with melamine matt finish MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Corner Table - Providing and placing executive corner table overall diamensions is (W)530mm x(D) 450mm x (H) 458mm. The whole body shall be Made with a combination of materials like MDF for the top and rubber wood for the understructure. The top shall be of MDF and tapered legs made of Rubber wood, both shall be in Lacquered in cappuccino shade. The table shall be having the load bearing capacity of 15 Kg. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Center Table - Providing and placing executive center table overall diamensions is (W)600mm x(D) 800mm x (H) 458mm. The whole body shall be Made with a combination of materials like MDF for the top and rubber wood for the understructure. The top shall be of MDF and tapered legs made of Rubber wood, both shall be in Lacquered in cappuccino shade. The table shall be having the load bearing capacity of 15 Kg. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Supply and installation of Canteen Tables for 900 Dia Table:-Understructure :- 3 pronged understructure mounted a vertical pipe support is used for 900 dia table top. The pitch centre dia for the prong is 700mm. The prongs are made of 2mm thick SS 202. The prongs are connected to a vertical pipe. The pipe is of 75mm dia and is made of 2mm thick SS 202. The height of the pipe is 563mm. The vertical pipe is connected to the table top with a help of the plate. The plate is 2mm thick CRCA powder coated to 40-50 microns and has a dia of 400mm. the height of the plate is 20mm. the complete understructure is supported by levelers of 19mm made of Nylon M8 threads. The dia of the Nylon leveler is 75mm. Table Top :- The table top can be either 25mm thick membrane as per the requirement. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

Providing and fixing Canteen Chairs with Back Rest- The back type is with Back rest with a height of 410 mm and back width of 400mm Max. The entire seat and back is a single moulded bend ply with laminate coating available in Cherry Red, Blueberry Blue, Lemon yellow and Citrus Pale Green. Seat- The seat height is 465 mm with a depth of 425 mm. The entire seat and back is a single Moulded bend ply with laminate on both sides. Understructure- The understructure is made of MS pipe with a DIA of 19*2 having a powder coated silver finish which is ROHS certified. The overall height of the chair is 875 mm with a max width is 469 mm. Special Feature- Designed to hold straps and hand bags, Designed bushes to help correct stackability and damping of shocks, I Design MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

HALF HT FREE STANDING PARTITION Vibrant plus partitoion (1st module metal type/second modle pi up+marker+fabric)@ 2100LX1350H TYPE -A [RATE & QTY IN SQM] Frames :- Partition thickness is 60mm for stability and with the inside gap between two tile is approximately 50mm for higher wire carrying capacity. Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.2mm thick. All the frames will be duly powder coated based on the choice of the Powder Coat colour , as per Customers choice, which will be inline with the Top trims & end trims, All the frames are fastened together by means of M6 NUTS & BOLTS . They can be attached to form a 2-way, 3-way or a 4-way configuration. All the Caps viz end, inline & universal & raceway caps are made out of Die-cast Aluminum. These caps also are finished in an epoxy powder coating finish in the same color.All the frames are fitted with M10 leveling bolts. MAKE : GODREJ / HARMANMILLER / WIPRO / FEATHERLITE / HAWORTH

3 W , LED COB Spot Light color temp. 3000/ 4000 Degree Kelvin, of approved make, Diecast Heat sink (philips,wipro,jaquar)

15 W , LED mirror Light (philips,wipro,jaquar)

IP20 non-integral flexible LED strip light (philips,wipro,jaquar)

4-16W LED Profile Light having 6MM to 25 MM Wide with aluminium profile recessed type covered with acrylic sheet flushed with false ceiling level. 3 - 6.5 Kelvin Temp. of approved make. 6 mm (Including LED Strip)

12 mm (Including LED Strip)

25 mm (Including LED Strip)

Supply, installation ,testing & commissioning of 1000VA ,60 minutes back up inverter with 12 volt Invagreen Exide or Farukawa make battery . The inverter is to be installed on every floor & connection shall be made with lighting DB for floor emergency lighting . Inverter shall be make MICROTECH/LUMINIOUS/EXIDE

Supply , Installation ,testing & commissioning of UPS 10KVA suitable for 20 minutes back up including necessary SMF type battery set . The UPS shall be 3 phase incoming & 3 phase output type & with Isolation transformer of suitable capacity. The UPS should be IP-30 design , Damp ,Vermin proof design with overload capacity of 125% for 15 minutes . UPS designed for 45 degree ambient Temperature. UPS Should be complete with all accessories battery connection wire /cables , cable/wire lugs , fabricated stand to install UPS & batteries. The UPS system & its accessories shall be as per tender & technical specification .Make Emerson / APC ( Equipment & computers )

LT Panel:- (Incomer)- Indicating Lamp 'R' Phase Led Type 240V-1 No., Indicating Lamp 'Y' Phase Led Type 240V-1 No., Indicating Lamp 'B' Phase Led Type 240V - 1 No., 6A SP MCB C Curve - 6 Nos. 250A FP MCCB 36kA-1 No. Spreader for FP MCCB-1 No., Rohm for MCCB-1 No., Shunt Trip for MCCB-1 No., ELR Relay with CBCT-1 No., MFM Meter Digital Type 96*96 SQ MM-1 No. , 250/5A C.T. CL-1 No., (Outgoing)- 160A FP MCCB 25kA-1 No., Spreader for MCCB-1 No. Rohm for MCCB-1 No., VMR Relay-1 No., 125A FP MCCB 25kA-1 No., Spreader for MCCB-1 No., Rohm for MCCB-1 No., 63A FP MCCB 25kA-4 Nos., Spreader for MCCB-4 Nos., Rohm for MCCB-4 Nos., 40A FP MCCB 25kA-1 No., Spreader for MCCB-1 No., Rohm for MCCB-1 No., 32A FP MCCB 25kA - 4 Nos., Spreader for MCCB - 4 Nos.

Providing & Fixing of 24-Port Data Switch of [Managed Layer-2 with 2-Giga Ports (10/100/1000) ] Make : D-Link, Cisco

Providing & Fixing of Wire Manager. Make : D-Link, Netgear, Techroutes

Providing & Fixing of Hardware. Make : D-Link, Netgear, Techroutes

Cable : Supply, Installation, Testing & Commissioning of 1.1KV/1100 V grade 2X1.5 sq. mm. copper Armoured Cable.

Cable : Supply, Installation, Testing & Commissioning of 1.1KV/1100 V grade PVC insulated 2X1.5 sq. mm. copper Flexibe Cable.

(a) Providing Following Unit for Conference System -Delegate Unit CMD -5200 :Each unit provided with a 470mm ( 18.5") long gooseneck condenser microphone which is highly sensitive and unidirectional. The microphone is provided with a diffuced LED housing to provided positive visual identification of the unit in operation. The built in speaker in each unit provides clear and crisp sound reinforcent . The output level of the speaker can be adjusted through a recessed volume control in the unit. Each unit has a headphone output Talk switch and a Talk LED . The MIC LEVEL LED in the delegate unit flicker to indicate microphone input signal level. Specification :- Microphone: -63dbV/ μbar (7.5mV/Pa) , Current Consumption : <50mA Max , Mic Auto Switch -Off Time :75 seconds approx. , Input : Line , Output : Line, Headphone , Speaker : Max Input 300 mW , Controls : TALK Switch , Speaker Volume control , Headphone volume control. , Dimensions : W118 x H70 x D160 mm , Weight :1.05 kg (w/o cable ) , Accesories : Foam Windshield 2.5m Interconnecting cable. Make : NX Audio / AKG ( Harman Pro ) / Philips / Ahuja .

(b) Chairmen Unit CMC-5100 :The Chairmen Unit has a TALK Switch with LED . It also has a PRIORTY switch with LED . When priority switch is pressed , a chime tone is generated to seek attention and mute the active delegate microphones. Specification :- Microphone: -63dbV/ubar (7.5mV/Pa) , Current Consumption : <50mA Max , Mic Auto Switch -Off Time : - , Input : Line , Output : Line, Headphone , Speaker : Max Input 300 mW , Controls : Priorty switch ,TALK Switch , Speaker Volume control , Headphone volume control. , Dimensions : W118 x H70 x D160 mm , Weight :1.05 kg (w/o cable ) , Accesories : Foam Windshield 2.5m Interconnecting cable. Make : NX Audio / AKG ( Harman Pro ) / Philips / Ahuja .

(c) Power Supply Unit ( Conference Controller ) with Main Voltage :10 to 240 VAC ± 10% . Make : NX Audio / AKG ( Harman Pro ) / Philips / Ahuja .

(d) Extension Cable : Providing & Fixing of Extension Cable Assembly of 10 Mtr. Make : NX Audio / AKG ( Harman Pro ) / Philips / Ahuja .

PA Amplifire with built -IN DIGITAL PLAYER TZA-2000® DP 200 WATTS . AC & 24V DC Operation - . 6 Mic, 2 Aux Inputs and CD/ Stereo input (L&R) . Built - in MP3 Player with remote control for USB , SD/MMC card reader . TZA-2000DP is ideal for medium sized installation such as in places of worship where two separate group of speaker are needed to be connected .User has a choice to connect both the zones to 100V (LMT) type speaker , or 100V speakers to one zone and low impendance type speaker to the other zone . Both the zone can also be connected to low impedence type speakers .Easy accessibility of DC fuses fitted on rear panel . Instant transfer to DC power ( Car Battery ) if AC power fails. Make : NX Audio / AKG ( Harman Pro ) / Philips / Ahuja

Providing & Fixing of 55" LED Display (pane) with Screen size : 55" Aspect ratio - 16: 9, Resolution 1920 x 1080 , Panel Type :IPS Brightness Time : 12ms , Viewing Angle : 178 x 178 deg. , Audio power : 20W (10W x 2 ) for External Speaker Make : LG /Sony / NEC .

Providing & Fixing of Wall Mount Bracket for 55" LED LCD TV

Providing & Laying of 48/0.2 mm 2-core sheathed copper special Speaker Cable

REMOVING , DEMOLITION OF ALL PARTITION , TABLE, CEILING, ELECTRICAL ITEM, CABLE, GLASS, DOORS, FLOOR, WINDOW TOILET TILE, FIXTURE ETC. FROM THE SITE & PLACED WITHIN 20 KM FROM THE SITE AND HANDOVER TO THE CONCERN DEPARTMENT.

Bidder Name

Amount

ABBOTTSONS IMPEX PVT LTD