COMPREHENSIVE REPAIR TO CERTAIN MD ACCN AT RIDGE AREA UNDER AGE B/R-1 OF GE SATWARI

Amount

Demolition of cement concrete (un-reinforced) ground floor to 2th floor and pavings n. exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish from the work site to out side defence premises complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3 Kg of cement per Sqm on surface, removing serviceable tiles to store and rubbish from the work site to out side defence premises complete all as specified and directed

M&L for glazed ceramic coloured tiles,300x450x7 mm thick as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 7 to 8mm thick non skid coloured ceramic joint less tiles (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:6 complete all as specified and directed.

M&L for 8 to 10mm thick coloured ceramic tiles (square/rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:6 complete all as specified and directed.

M&L for 8 to 10mm thick coloured ceramic tiles (square/rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , as in vertical surfaces , set and jointed in neat cement slurry over and including 10 mm thick cement plaster in cement mortar 1:4. complete all as specified and directed.

M&L for granite work 16 to 18 mm thick (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for repairing of concrete surfaces such as balcony, chajjas, upward or downward facia ,column, pillar, ceiling and similar items with plain cement concrete 1:2:4 type B-0 (using 12.5mm thick crushed stone aggregates) or with 15mm thick rendering in cement mortar 1:3 without using extra cement,surface finished even and fair (as per site requirement) complete all as specified and directed. (Note:- Quoted rated shall be deemed to include:- (i) formwork and scaffolding required & taking down or dismantling as per site requirement (ii) The work is to be executed upto 4th storey building

M&L for complete removal of existing treatment on wall/Ceilling,roof projectios,Including facia,cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour complete all as specified and directed .

M&L for water proof cement based putty @ 1kg (un-diluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding ) including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:- Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute. Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation.

M&L for one coat of acrylic water based exterior (wall/ceilling up to 4th storey with necessary scaffolding) grade primer @ 0.9 ltr /10 sq mtr (un-diluted) diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed. .

M&L for water based premium acrylic smooth interior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed .

M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed . Notes for Srl item No 15 to 18 of BOQ :- (a) The work for periodical services shall include the under mentioned aspects and the rates quoted by the bidder shall includes and the same & nothing extra shall be payable. (i) Work shall be carried out by the authorised applicator of manufacturer of water based premium acrylic smooth exterior emulsion, contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. (ii) Work shall be carried out up to 4th storey height buildings and the necessary scaffolding , trestles , ladders ,cradles & safety measures shall be arraged by the contractor for labour and their own . (iii) Removing of nails & making good holes, cracks etc. (iv) Work in patches and in narrow /widths ,bands ,cornises ,plasters etc shall also be carried out and cutting in edge of line where ncessary. (v) Spreading and removing covering to doors ,windows ,floor ,fittings etc to protect them from splashes. (vi) Washing floors , cleaning glass ,joinery, fittings, wiring etc from drops and splashes of paint to be cleaned to the statisfaction of Engineer-in-charge. (vii) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for preparation of new or previously untreated wood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described by rubbing with sand paper or grinding by hand grinder to make surface even and smooth & apply primer where required and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description over 10cm width or girth not otherwise described by grinding the uneven surfaces and necessary filling of putty (as and where required) to make surface even and smooth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F machine cut kota stone slab in flooring, treads of steps (one piece including rounding/ mouldings of edges of treads), 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 after roughing surfaces of old concrete /any type of plaster by picking sweeping down with water to remove dust etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:3 as in sunken floors/walls , surface finished even and smooth without using extra cement including mixing of water proofing compound complete all as specified and directed

M&L for plain cement concrete 1:5:10 type E2 (using 40 mm graded crushed stone aggregates) in filling and mass concrete complete all as specified and directed

M&L for steel water tubing of 40 mm bore,medium grade,galvanised, laid in sunken floors as spout complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with double rebate including mild steel hinges, 100 mm long , medium weight and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with single rebate including mild steel hinges, 100 mm long , medium weight and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood , glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers size of members of shutters as specified complete all as specified and directed.

M&L for 30mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. square tube, egdes will be painted to match printed sheets complete all as specified and directed .

S&F Factory made solid PVC moulded door shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed

Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided and removing the rubbish from the work site to outside defence premises complete all as specified and directed.

M&L for RCC 1: 2:4 type B-1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in shelves complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed .

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia,in stirrups, spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of form work to edge of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls , floor and roof and not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10cm but n. exc 20 cm wide for fair finished surfaces of concrete complete all as specified & directed.

M&L for pressed steel cup board frame made out of MS sheet 1.25mm thick, size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 type B-1 as in filling to back of chowkats including butt hinges 100 mm long complete all as specified & directed.

M&L for prelaminated MDF board (exterior grade) 18/19 mm thick as in shutters /shelves ,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including lipping (15mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and directed.

S&F in repair continuous (piano) hinges,30mm width, heavy duty, mild steel ,bright finish or electrogalvanised suitable for 19mm thick shutter complete all as specified and directed

S&F 100mm long stainless steel butt hinges, fixed with screws complete all as specified and directed

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F aluminium anodised , fabricated type handle 150mm size complete all as spcified and directed.

S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed.

S&F hasp & staple 75 mm in length, safety type, aluminum anodised with steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed.

S&F aluminum hanging floor door stopper ,twin rubber of size 100mm, anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour and shade with necessary screws complete all as specified and directed

S&F in repair aluminium bottom door seal with brushes of length 1.20 m and fixed with screws to door complete all as specified and directed.

S&F in repair 200 mm size mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed

Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed. Note: For measurement superficial area in elevation shall be measured.

S&F factory made prelaminated solid 18mm(+0.7mm) thick celuka PVC foam ply,glossy finish, one side prelam and other side plain of density 600Kg/cbm for kitchen cabinet shutter/Wardrobe/partition/shelf complete all as specified and directed .

S&F aluminium anodised , fabricated type handle 100mm size complete all as spcified and directed.

S&F steel fasteners of size 75 mm long, drilled and fixed to walls complete all as specified and directed.

M&L for 50 mm magnetic catcher with brass body and striking plate including letting in as fixed complete all as specified and directed.

Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per Srl item No -59 here-in-before but except bricks complete all as specified and directed.

M&L for brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed .

M&L for factory made box type steel windows/ventilators, double shutter,outer frame made out ERW TUBE 'P section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) openable shutters side hung including pintle hinges with two nos MS tower bolts 150mm size on each shutter, steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required steel windows will be double shutter (external glazed and internal wire gauzed) complete all as specified in Drg No CEPZ/TD-324/07 of sheet No 1/3 to 3/3 complete all as specified and directed. Note: - The quoted rate shall be deemed to include :- (i) 04 Nos MS steel lugs of MS flat 20 x 5mm & 20 cm long over all welded to frames (ii) PCC block for embedding lugs.

M&L for framed work such as grills , gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirming to Fe290, Gde E-165 complete all as specified and directed

M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with glazing pins, oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed.

S&F 3 mm thick , figured glass, pin head type and glazing with oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge with stainless steel brackets near to ends with stainless steel finials at both ends and necessary fittings complete all as specified and directed.

Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof, finished & laid to required slope complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces of roof finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

Supply only liquid water proofing compound.

M&L for water proofing treatment to roof surface (in four coat) with fibre reinforced elastometic liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110 having minimum elongation of 350%, tensile strength 2.9 MPa and shall have rack bridging ability upto 10 degree celcius to RCC roof slabs, roof treatment shall be carried out in four coats to newly plaster roof surface as per the procedure given below :- (a) Apply first coat of fibre reinforced elastometic liquid water proofing membrane as described above with 33% dilution as priming coat as directed and allow it to dry before next coating. (b) Laying second coat of fibre mesh 0.3 mm thickness weave in leno pattern having weight 45 gms per sqm and pasting it properly with overlap of 50 mm as directed and allow it to dry before next coating. (c) Apply third coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed. (d) Apply fourth and final coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed. (e) Ther water proofing treatment shall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commencement of roof treatment work.

M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent). Base coat: Berger HS Latex plus (or equivalent) both on wall (upto 1 mtr min height) and floor. Consumption base coat: 0.3 kg/sqm Reinforcement: Glass fiber Second and Third coat: Latex sheild 2K (or equivalent) both on wall (upto 1 mtr min height) and floor. Consumption top coat: 3 kg/sqm System requirements: density: 2.00 kg/ltr compressive strength: 0.5 N/mm². • Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent). • Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft. • All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc complete all as specified and directed .

M&L for capillary rise treatment of walls with following specification:- Base coat: Berger HS Latex plus or equivalent in make specified in PS Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K or equivalent in make specified in PS Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr compressive strength: 0.5 N/mm2.

M&L for dismantling of water tank of capacity exc 250 n. exc 500 ltrs and removing complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed.

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F in repair bib tap ,chromium plated, fancy type, cast copper alloy , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair bib tap with long body, chromium plated, fancy type, cast copper alloy , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and directed.

S&F in repair 2 in 1 angle valve with flange, chromium plated, fancy type, cast copper alloy, screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair brass chromimium plated sink mixer swan neck with swinging spout (wall mounted model) with connecting Legs & wall flanges complete all as specified and directed.

S&F in repair 15mm bore Stop valves, cast copper alloy,fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed , complete all as specified.

S&F in repair brass chromium plated central hole basin mixer for hot and cold water, screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed

S&F in repair brass chromium plated tubular towel ring of 150mm dia, fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair corner glass shelf of size 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed .

S&F Chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F shelf of PTMT with and including chromium plated brass screws and plastic cleats complete all as specified and directed .

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and direced.

S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed.

S&F sinks , made of 1.0mm thick stainless steel,overall size of sink 495mm x 420mm with bowl size 410mm x 330mm x 160mm, plugs, washers, waste pipe , union, CP waste coupling and cantilever brackets embedded in cement and sand mortar in wall complete all as specified and directed

S&F in repair plate rack made of 1.0mm thick stainless steel of size 36"x30"x10" fixed with steel fastners or steel screws complete all as specified and directed

S&F in repair vitreous china wash hand basin, white, flat back of size 600x480mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed

S&F in repair vitreous china corner wash hand basin, white, of size 555x420mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed

S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern) of size 520x360x390mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F in repair chromium plated Jet spray with 1.50m long flexible tube and fixed complete all as specified and directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store complete all as specified and as directed

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store complete all as specified and as directed

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall/ceiling and laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall/ceiling and laid in floors complete all as specified and directed

M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, Iintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm grith complete all as specified and driected.

S&F in repair stainless steel lock grating plain/hole of 100 mm dia including embedding in tiles with white cement complete all as specified and directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed

S&F PVC (SWR) type B pipes, 110 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F PVC (SWR) type B pipes, 75 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends with access door, 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed

S&F PVC (SWR) bends with access door, 110 mm bore complete all as specified and directed

S&F PVC (SWR), branch piece, single, (single 'Y') with access door equal or unequal for 75 mm bore complete all as specified and directed

S&F PVC (SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore complete all as specified and directed

S&F PVC (SWR), reducer 110 mm dia complete all as specified

S&F PVC (SWR) vent cowl 75 mm dia complete all as specified

S&F in repair UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F in repair UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for plain cement concrete 1:2:4 ,type B0(using 12.5mm graded crushed stone aggregates) as in step, seismic and other similar bands, parapets and railing nup to 60 cm heigh, coping, apex stones, bed plates, roof padding and the like including weathering slightly rounded or chamfered angles including necessary formwork complete all as specified and directed.

M&L for grubbing up vegetation, small trees from roots, clean the loose dirt with water and repair the same portion with cement mortar 1:3, touchup with same finish, area not exc. 0.10 sqm each adjacent to CI pipe upto 4th storey building with necessary scaffolding/ ladder complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate), as in sub base of floors, finished even and fair complete all as specified and directed

M&L for providing and laying 60 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C2 (using 40 mm graded crushed stone aggregates) as in sub base ,finished even and fair complete all as specified and directed

M&L for machine pressed chequered cement concrete tiles 30cmx30cmx25mm thick, with grey cement and pigment, set ,jointed and pointed in neat cement slurry as in floors, laid over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed .

M&L for 25 mm thick plain cement concrete 1:2:4, type B1 (using 20 mm graded crushed stone aggregates) as in sub base ,finished even and fair complete all as specified and directed

M/S Shesh Paul Gupta (BID ID -3390827)

STAR CONSTRUCTIONS (BID ID -3391448)