PROVN OF HARD STANDING PARKING AREA NEAR BUILDING NO E-53 (UNIT LABORATORY) OF MH MATHURA AND REV NOS 50, 65, 76 AND 77 UNDER GE (E) MATHURA

Amount

Surface excavation n.exe 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified.

M&L 100mm thick PCC M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub floor all as specified & directed by Engr-in-charge.

S&F Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade laid over and including 25 mm thick sand cushioning complete.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate as in plinth protection, surface finished even and smooth without using extra cement all as specified.

M&L brick work with fly ash bricks straight or courved on plain n exc 6 m mean radius for manholes/ septic tank /soakewell etc built in cement mortar 1:4.

M&L rendering 10 mm thick on ceiling in CM 1:4 finishing even and smooth complete.

M&L for preparing newly plastered surface of ceiling and applying three coats of white wash complete all as specified.

M&L for 100mm thick PCC M 7.5 (Nominal mix) using 40mm graded stone aggregate is in sub base complete.

M&L chequered cement concrete tiles with gray cement and pigment 30cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry in floor over & incl 20mm thick screed bed CM 1: 4.

S&F 18 mm thick PVC solid kitchen cabinet sides top & bottom & shelves made out of PVC ply both side white colour sheet of density 600 kg/cum bent at 90 degree and fixed with screws, solvent cement/ adhesive finish all edges at level for making edge lipping/bending or 0.5 mm thick PVC sheet lipping at all four edges using bonding lap etc complete as per direction of Engineer in charge & all as per manufacture specification.

S&F 18mm thick factory made PVC celuka ply with one side prelaminated & other side plan white to make kitchen cabinet /drawers, shetter of required size consisting of panel to be edge lipped by 18 mm width x 1mm thick, PVC ply shall be of density not less than 600 kg/cum complete all as specified and directed by Engr-in-Charge.

S&F factory made PVC Cabinet of required size fabricated by joining 12 mm thick PVC celuka ply fixed with each other using solvent cement fixed with screw and solvent cement adhesive etc. To make wall mounted kitchen cabinet back & pull out drawers sides complete as per specifications and as directed by the Engineer - in -charge.

S&F auto closing hinges 35mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters. Make:- KAFF, Godrej, Hettich

S & F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kg. Make:- KAFF or equivalent approved make.

S&F stainless steel handles 100mm size for kitchen cabinet shutters. Make:-KAFF, Godrej, Hettich

S&F chrome plated stainless steel wire basket (Storage basket) pull out type for large utensils, suitable for modular Kitchen of any size and description with necessary fixing clips etc complete in all respect as specified and directed by Engr in charge

Demolition of un-reinforced cement concrete any description and in any position not otherwise specifically provided for

M&L for providing 25 mm thick cement concrete M-15 grade (Nominal mix) using 20 mm graded stone aggregate complete all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for Glazed ceramic tiles in vertical surface 350x250x7mm/450x350x7mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified.

M&L PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in coping edging to interlocking tiles etc. complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying cable etc and getting out in soft/loose soil complete.

M&L for cement concrete M-7.5 grade (Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4.

M&L for 40mm thick Damp proof course in cement concrete M-15 grade (Nominal mix) using 12.50mm graded stone aggregate on horizontal or vertical surfaces including water proofing compound & necessary form work all as specified. Note : Water proofing compound shall be measured and paid for separately under relevent item of this BOQ

Supply only water proofing compound.

Returning, filling in, in-cluding spreading, levelling, watering and well ramming in layers not exc 25 cm. thick complete all as specified and directed by Engr-in-charge.

M&L for providing RCC M-25 grade (Design mix) 20mm graded stone aggregate in lintel/chajja

M&L for RCC M-25 grade (design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed.

M&L TMT bars 10mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., complete.

All as per item No. 33 above but 5mm to 10mm dia as in striups, spacers & binders all as specified.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc n. exc 200mm thick etc complete all as specified and as directed.

M&L for use & waste of steel form work (rough finished flat) to edge of concrete flat, roof slabs, shelves etc not exceeding 200mm thick complete.

M&L for providing 25mm thick M-15 grade (Nominal mix) using 20mm graded stone aggregate as in floor finish complete.

M&L rendering 15 mm thick (10mm + 5mm) plaster on other than fair face of brick work in CM 1:4 and surface finished even and fair by mixing integral water proofing compound in finishing coat as per manufacturers instructions complete. Note :- WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L for rendering 15 mm thick in CM 1:6 on than on brick or concrete surfaces and finished surface even & fair complete all as specified.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of plastered surface of walls including plaster / cornices etc and applying two coats of oil bound distemper over one coat primer complete all as specified and as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification & drawings in SSR Part II of 2010.

S&F factory made solid panel PVC moulded door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheets for top rail & bottom rail Panelling plain colour PVC sheet to be fitted in MS frame welded/sealed to the style & rails with suitable PVC sheet beading as per specification & shown on drawing in SSR Pt II of 2010 complete all as specified.

S&F 150mm long Aluminum handle cast type anodised all as specified.

S&F 100mm but hinges, extruded brass, with mild steel hinge pin, bright polised and fixed, type B-11 all as specified and directed

S&F for 150 mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half protion & adjustable type louvers in another hald and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator all as directed by Engr-in-charge

S&F 500 liters capacity rotational moulded polyethylene three layer water storage tank (Cylindrical vertical with close top) hoisted and fixed in position including connections including dismantling existing old water storage tank all as specified.

S&F 15 mm bore tubes medium grade galvanised, with all fittings and fixed to complete to walls and ceiling or laid in floors complete.

S&F 20 mm bore tubes medium grade galvanised, with all fittings and fixed to complete to walls and ceiling or laid in floors complete.

S&F ball valves high pressure of PTMT 20 mm bore with epoxy coated Aluminium rod & high density plastic ball 20 mm bore.

S&F Vitreous China wash down water closet pan (pedestal pattern), white including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and directed. Make:CERA/Jaquar

S&F 110mm cast iron traps 'P' or 'S' for water closet.

S&F in repair Vitreous China urinals, half stall type white (Excluding flishing cistern, flush pipe and waste pipe) fixed.

S&F vitreous china wash hand basin,white, flat back size 580x450 mm including CP pillar tape fancy type suitable for 15 mm bore pipe 32 mm bore CP brass waste coupling and brackets complete all as specified.

S&F angle cock/valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed with ends for iron pipe or union and fixed of 15mm dia. Make :- Cat part No ESSCO APR-101053 all as approved by Engr-in-charge.

S&F bib taps chromium plated cast copper alloy with crutch or butter fly handle screwed down, screwed for iron pipe of bore 15mm complete.

S&F wash basin mixer 15mm bore all as specified. Make:- ESSCO cat part No APR 101011B or equivalent make given under list of make.

S&F 15 mm bore PVC connection with PTMT nuts of length 450 mm.

S&F Gun matel, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F PVC (SWR) bends of any radius 75 mm bore complete.

S&F in repair PVC (SWR) floor trap plain with grating including jointing with solvent cement dia of out let 75 mm including stainless grating fixed complete all as specified and as directed.

S&F PVC (SWR) bends 110 mm bore with or with out oval excess door complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete M-15 grade (Nominal mix) smooth finished, and reforming benching as required 150 mm bore of pipes.

M&L salt-glazed stoneware drain pipes 150mm dia laid in trenches and jointed as specified.

M&L for Concrete bed to drain pipes M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate bore of pipe 150 mm including packing under, and haunching against the sides of pipes after they are laid and tested.

Material and labour for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (phase- Red, Neutral - black, Earth- Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings/ fixing accessories after cutting chases for conduits and sunken GI pressed steel terminal boxes covered with 3 mm thick phenolic laminated top sheet cover white for mounting switches sockets, bell push, regulators etc and making good to walls, floors etc for one light /fan/ bell point controlled by one switch complete.

S&F switch flush type 5Amps single pole, one way conforming to IS 3854 and ISI marked

S&F ceiling rose, surface bakelite with three terminal

S&F lamp holder PVC polycarnonate type with back plate.

S&F LED retrofit lamp 7 Watt all as directed. Make-C&S, Cat part No LTHPLEDLAMP7W/B22 or equivalent in Philips/Osram.

S&F integrated type LED tube light fitting, indoor decorative aluminum extruded T-5, 4 ft white complete of capacity 1x20 Watt including making electrical connections with twin core twisted flexible copper wire of suitable size all as directed. Make :- Cat Part No LTTB4F20WLED/W in C&S or equivalent in Philips/Osram.

Supply & fixing LED Bulk Head with PDC aluminium housing and milky diffuser capacity 10 Watt complete including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as directed. Make :- Cat part No LTB10WLED in C&S or equivalent in Philips/Osram.

S&F factory made epoxy powder coated distribution board SPN 4 ways (SPN MCB DB) with metal door (IP-43 protechtion) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standad DIN rail, earth bar and cable tiles for cable ties for cable management, top and bottom removeable gland plates with knokout complete all as specified.

S&F single pole and neutral (SPN) MCB 40 Amps 240 V50Hz 10Ka breaking capacity complete all as specified.

S&F single pole (SP) MCB 6-32 Amps, 240V, 50Hz, 10KA breaking capacity all as specified

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

S&F heavy duty exhaust fan 300 mm sweep, metal body single phase, 230 volts including fixing arrangements with louvers with cutting chases and making hole and making good the distrubed surfaces complete all as directed.

Ms Kamal Kant Agarwal

JWALA ELECTRIC CONTRACTORS

CHOPRA ENTERPRISES