SPL REPAIR TO BLDG Nos. T-11, T-15, T-21 (ACUTE WARD), T-25, T-26, T-70 (ADM OFFICE AND MAIN OFFICE), T-48, T-49,T-50, T-51(TOILET BLOCK), T-54, T-55, T-57, T-58, T-59, T-60 (WATER TANK 2000 GLS) AND P-1611 (MAIN GATE GUARD ROOM) AT

B/R PORTION:- M&L for rendering 20 mm thick on concrete surface, roof top surfaces in cement mortar ( 1:4) including water proofing compound and finished even & smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note : Supply only WPC will be measured and paid separately.

M&L for 40 mm thk PCC (1:2:4) Bo using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope complete all as specified and as directed by the Engineer-in-Charge. Note :- Supply only water proofing compound shall be measured & paid separately

M&L for applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed by the Engineer-in-Charge.

M&L for Chipping of slab/columns/ beams/chajjas /parapet /roof projection/ balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts complete all as specified and as directed by the Engineer-in-Charge. Note :- Scaffolding/ temporary support structure required to support the members / structure during strengthening shall be include in this items

M&L for applying bond coat cum waterproofing on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar with two coats of Slurry- @ approximately 2- 2.5 m2 / litre depending on substrate porosity of Fosroc Nitobond SBR300 or equivalent Equivalent etc as per manufacturer specifications. Laying of reinstatement readymade plaster/polymer mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete complete all as specified and as directed by the Engineer-in-Charge. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height.

M&L for applying to the damaged concrete portion of slab / columns / beams / chajjas/ parapet /roof projection/ balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair mortar Sika monotop 122F (having the technical parameters mentioned in material specifications) capable of applying up to 20-30 mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and as directed by the Engineer-in-Charge. Note :- Scaffolding/ temporary support structure required to support the members / structure during strengthening shall be include in this items

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for Granite of black / green / imperial red (colour as approved by GE) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed or 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and as directed by the Engineer-in-Charge. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing and single piece complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of flooring/hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base of floors & finishing the surface even & smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,including 15mm screed bed in CM 1:6 in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid tiles coloured 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/ highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair CP soap dish standard size complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by the Engineer-in-Charge.

S&F 75mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair, 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair, PVC (SWR) bends of 75mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 24.00 here-in-before above but of 110mm bore.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and as directed by the Engineer-in-Charge.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair, PVC (SWR) cowl of 75mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair, PVC (SWR) cowl of 110mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for PVC (SWR) floor trap 75mm diameter of outlet, plain with grating including jointing with solvent cement incl jointing to waste pipe fixed in cement concrete type 1:2:4 B-1 using 20mm graded stone aggregate complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore cast copper alloy chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair corner glass shelf size 300 mm radius with and including bracket and glass complete set etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm dia Bib tap (2 in 1 type) of brass, chromium plated fancy type glossy finish fixed to wall complete all as specified and as directed by the Engineer-in-Charge. Make :- cera cat part No F-1015163 or Jaquar/ Hindware/ Prayag/ Parryware or equivalent model as approved by GE.

S&F in repair pillar tap, cast copper alloy fency type chromium plated screwed down high, pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed to 15mm bore of pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs tubler towel rail brass chromium plated 20mm dia, D type 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair wash basins vitreous china, white /coloured flat back size 550 x400mm fixed including bracket complete all as specified and as directed by the Engineer-in-Charge.

S&F 15mm bore of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors specified. with all fittings such as brasss Tee, brass elbows, brass sockets, brass unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making good to floor etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC connection 15mm size with PTMT nuts and polythene washers of 450mm length complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Swivel shower rose 75mm size with arm 195mm long with bend of 45 degree with flange of PTMT any colour fixed complete all as specified and as directed by the Engineer-in-Charge..

S&F in repair Glass shelf size 600 mm long with and including bracket and glass complete set etc. complete all as specified and as directed by the Engineer-in-Charge. Make :- cera cat part No. F5001114 or Jaquar/ Hindware/ Prayag/ Parryware or equivalent model as approved by GE.

S&F in repair 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15mm fancy type, chromium plated with long shank and cup (concealed type Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

Providing and fixing powder coated 50 microns extruded aluminium Windows/glazing, window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including 4 mm thick tinted glass, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1no.) complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made.

S&F 30mm thick Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made.

S&F 35mm thick Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type skelton door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt / Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.20mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in door at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf Note :- The cost of SS butt hinges, tower bolt and handles shall be deemed to be inclusive in the unit quoted rates.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in door at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stopper - 1 No per leaf Note :- The cost of SS butt hinges, SS tower bolt, SS handles sliding door bolt/Aldrop and door stopper shall be deemed to be inclusive in the unit quoted rates.

M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying Two coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster on brick/concrete/stone masnory surfaces of any description complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 20 mm thick(in two layers-first layer 15MM thick with readymix plaster and outer layer 5 mm thick readymix waterproof plaster) on outer wall walls by adding potable water by weight of material as mentioned by manufacturer. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1981, IS 2402-1963 and shall confirms the Compressive strength @ 28 Days- 10-15 Mpa/ Bulk density- 1600-1800 Kg/m3 and pull out bond strength->0.5MPA complete all as specified and as directed by the Engineer-in-Charge. Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20MTR height

M&L for rendering 15 mm thick (in two layers-first layer 10MM thick with readymix plaster and outer layer 5 mm thick readymix waterproof plaster) on outer wall walls by adding potable water by weight of material as mentioned by manufacturer. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1981, IS 2402-1963 and shall confirms the Compressive strength @ 28 Days- 10-15 Mpa/ Bulk density- 1600-1800 Kg/m3 and pull out bond strength->0.5MPA complete all as specified and as directed by the Engineer-in-Charge. Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20MTR height

M&L for rendering 5 mm thick readymix self curing plaster on ceiling by by adding potable water by weight of material as mentioned by manufacturer. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1981, IS 2402-1963 and shall confirms the Compressive strength @ 28 Days- 10-15 Mpa/ Bulk density- 1600-1800 Kg/m3 and pull out bond strength->0.5MPA complete all as specified and as directed by the Engineer-in-Charge.

M&L for Two or more coats on new plastered surface distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification including 1mm thick wall care putty complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over old surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L Preparation of old distempered and painted surfaces including washing, rubbing down and stopping by brooming down , scraping down smoke soot, moulds, moss and efflorescent salts and Two or more coats on old plastered surface distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification two or more coats on new work including 1mm thick wall care putty complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old decorated surfaces of walls (plastered or unplastered) and cornices, by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of white wash on walls complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs door closer hydraulically regulated designation No 3 universal type suitable for door shutter 851mm to 1000mm vide and weight between 61 to 80 kg of aluminium (extruded section body) as in repairs complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of existing unserviceable RCC/PVC water tank and S&F 1000 litre capacity rotational moulded polythene water storage tanks Triple layer (cylindrical vertical with closed top) hoisted & fixed in position complete all as specified and as directed by the Engineer-in-Charge.

Dismantling boarding of any description fixed in any position with nails complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made 18mm thick both side laminated HDHMR board in modular kitchen carcasse made of minifix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made 12mm thick both side laminated HDHMR board in modular kitchen carcasse made of minifix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails complete all as specified and as directed by the Engineer-in-Charge.

Supply only SS soft close clip on hinge bright finish complete all as specified and as directed by the Engineer-in-Charge. Note :- ISI make and shape as approved by GE.

Supply only 125mm brass finish handle for cabinet shutters fancy type bright finish complete all as specified and as directed by the Engineer-in-Charge.. Note :- ISI make and shape as approved by GE.

S&F mortice lock brass 4 levers vertical type with handle, size 100mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod and including 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc complete all as specified and as directed by the Engineer-in-Charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

M&L for 100 mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring / hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by the Engineer-in-Charge. Note: colour and design as approved by GE.

M&L for rubber moulded 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by the Engineer-in-Charge. Note: colour and design as approved by GE.

M&L for PCC 50mm thk type C1 1:3:6 (20mm graded stone aggregate laid in alternative as in plinth protection including finished the surface even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for ceramic out door tiles 400mmx400mmx12mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 15 mm thick Cement Mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for 75 mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in subbase of flooring / hard standing complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

S&F MS hollow rectangular/square/circular tubes/pipes of YST 310 Grade as in frame work for roofs/rafters/purlins/chajjas/trusses/ columns/ struts etc and like similar items etc.complete all as specified and as directed by the Engineer-in-Charge.

M&L for New framed work as in doors or gates of angle Fe-410 W ( Gde-E-250) quality B or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of plain or corrugated steel sheets in roof coverings any type complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified and as directed by the Engineer-in-Charge.

M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete all as specified and as directed by the Engineer-in-Charge.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as recommended by manufacturer all as specified colour/pattern as approved by GE).

Providing & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4-6mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repairs for Toilet fittings Wall mixer (wall mounted model) with 1.5m flexible tube and hook complete all as specified and as directed by the Engineer-in-Charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of 150mm bore set in cement mortar including demolition of packing under and hauching against sides of pipes complete all as directed by Engineer-in-charge. Note :- Excavation and earth work shall be measured and paid separately under relevant items.

All as per item No. 94.00 here-in-before above but of 200mm bore.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 96.00 here-in-before above but of 200mm bore.

M&L for Reinforced concrete pipes of dia 150mm bore, class NP2, laid and jointed complete with collars laid in trenches and jointed in CM (1:1) and tested complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 98.00 here-in-before above but of 200mm bore.

M&L sand stone slabs 5 cm thick in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft/loose soil complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping/conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, etc and making good disturbed surfaces complete all as specified and as directed by the Engineer-in-Charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site making good the disturbed surfaces to match with the existing finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLSH cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 2.5 Sqmm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed by the Engineer-in-Charge for the following :- Note : Modular switch and socket shall be measured and paid separately.

All as per Item No. 106.00 here-in-before above but One light point controlled by one switch.

All as per Item No. 106.00 here-in-before above but One Ceiling /Exaust fan point controlled by one switch.

All as per Item No. 106.00 here-in-before above but for one bell/buzzer point controlled by one push botton.

All as per Item No. 106.00 here-in-before above but One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per Item No. 106.00 here-in-before above but with copper conductor cable of nominal class area 2.50 sq mm for phase ,neutral & earth for One 2/3 pin socket outlet 5Amps on independent board.

All as per Item No. 106.00 here-in-before above but with copper conductor cable of nominal class area 4.0 sq mm for phase ,neutral & earth for power socket point 15 A .

S&F modular switch one way 6A, 1 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular socket 6A-2/3 pin combined 2 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular switch socket combined 6A/16A , 6 pin, 3 module complete all as specified and as directed by the Engineer-in-Charge.

S&F of modular bell push flush type 5 Amps complete all as specified and as directed by the Engineer-in-Charge.

S&F modular fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connectingup complete all as specified and as directed by the Engineer-in-Charge.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete all as specified and as directed by the Engineer-in-Charge.

S&F of bell AC single pole Ding Dong type 230 volt complete all as specified and as directed by the Engineer-in-Charge.

S&F MCCB D B VTPN 8 way 415 V double door IP -43 with provision for FP MCCB/Isolator/RCCB etc as incommer and SP/TP MCBs as out going complete prewired including Bus Bar etc suitable for operation on 415 volt 50 Hz AC supply complete all as specified and directed by Engineer-in-Charge.

S&F in repair MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCCB 4P 415 volts 16 KA suitable for fixing on VTPN DB of capacity 125 Amps with extended terminals complete all as specified and directed by Engineer-in-Charge. Note :- (i) Suitable size and frame of MCCB required as per existing DBs at site. (ii) MCCB Rating ICS=100 % ICU

S&F in repair MCB's single pole and neutral 40 to 63 Amps, 240 Volts,10 KA rapturing capacity 'C' curve.complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for submain wiring with approved colour code/as per IS (Red,black & green for single phase)concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and as directed by the Engineer-in-Charge. Note :- Two runsof 6.00 Sqmm cable & one run of 6.00 Sqmm cable shall be paid as one unit length

S&F in repair Geyser/AC Box having 20 Amp MCB SP enclosure as incomer complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair building security light fitting LED 15 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED as lihjting souce and PC cover having TOP opening sepreate drive compartment etc and connecting complete all as specified and as directed by the Engineer-in-Charge.

S& in repair bracket of GI pipe medium grade of 40mm dia ,1.2 meter in length clamps made of FI 40 mm x 6mm incl nuts ,bolts & washers including synthetic painting complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair LED light fitting 18/20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connection up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair LED tube light fitting 10 watt tube LED Neutral white in colour, 2 feet in length wall mounted LED batten, extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver, optic diffused type ENDURA LINER NEO including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair recessed/ceiling/Surface/POP mounted down lighter with CRCA housing with high bright LED , idealy suited for low ceiling areas 50Watt LED (100 Lumen/watt or higher) size 2ft x 2ft. The product features color tuning from 3000 - 6500 K, necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair LED post top lantern/gate Light 40 watt light fitting made of die cast top housing must also be dia cast aluminium spigot housing with decorative acrylic diffuser with IP 65 protection complete with all accessories including removal of old unserviceable LED poet top lantern/gate light complete all as specified and as directed by the Engineer-in-Charge. Make - Crompton Cat part No. CBP-610-40-57-SL-CA-NBK or equivalent make and model as approved by GE.

Taking down ceiling/exhaust fan of any sweep sealing cable end dismanting blade and removing fan and blade to store complete all as specified and as directed by the Engineer-in-Charge.

M& L for painting of ceiling/exhaust fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler one coat after cleaning all dust etc complete all as specified and as directed by the Engineer-in-Charge.

Fixing only of ceiling/exhaust fan after rewinding/servicing greasing change of bearing if reqd ,including making serviceable and noise free in all respect and connecting up including provn of cable from ceiling rose or connector to fan complete all as specified and as directed by the Engineer-in-Charge. Note :- Rate Quated by Contractor shall be inclusive for replacing all unsv item like quater pin ,nut bolt with check nut ,rubber real etc.

Taking down storage geyser of any capacity after disconnecting electrical connection from existing socket ,removing the bolts and nuts from wall and disconnected inlet and outlet water connection and handover to unit for keeping it in safe custody complete all as specified and as directed by the Engineer-in-Charge.

S&F water heater, storage type (geyser) vertical type inner container of capacity 25 litres power 2.0 KW, BEE 5 Star rated pressure rating >8 bar electrically operated, AC 230 volts including as per site required Nos of fashner nuts required suitable size fixed in brick/stone wall complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC connection pipe chromium plated 15mm dia both end threaded including brass coupling bolt cone washer complete, length of pipe is not less 450mm suitable for Hot/Cold water system complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15mm cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete of size 15mm dia complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two runs of single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 4.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engineer-in-charge. Note :- Two runs of 4.00 Sqmm cable & one run of 4.00 Sqmm cable continuity earth and one run of PVC conduit with all necessary accessories shall be paid as one unit length

M&L in repair bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to 4.00 mm dia GI wire as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 15 mm dia light grade Gi /CPVC pipe for earth lead protection connected to electrical equipment and earthing test point , earth dolly and earth chamber as shown in elect plate No 2 of SSR Pt-I including all necessary earth work, excavation, earth chamber with PCC 1:3:6, Type C1 and RCC chamber cover of PCC 1:2:4 with handle and 20 mm dia GI watering pipe with funnel and wire mesh etc and testing on complete all as specified and as directed by the Engineer-in-Charge. Note : Testing of earthing of any type, after disconnecting from test point and other loops by using ISI marked digital/Analog earth tester of reputed make and test result shall be entered in a Earth Testing register and put up to the Engr-in-Charge after testing complete all as specified and directed. Test result for item No. 7 and all earthing in schedule to be provided to Engr-in-Charge before completion of work. Earth tester to be provided by the contractor himself.

M&L in repair for Earth continuity strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to DBs or any other indicated situation for loop earthing with copper strip of size 20 x 3mm size complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair GI Tubing light grade 40 mm dia.for cable protection complete all as specified and as directed by the Engineer-in-Charge.

S&F wall mounted fan swing type 400mm sweep, Voltage AC 220-240V, 55/60 Watt airflow 2450CFM, energy efficient 5 star suitable for indoor/outdoor with two year manufacturing warranty including taking down old unserviceable wall mounted fan and deposited to MES store yard complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair condenser 2.5 Mfd, 240 volts for ceiling/exhaust fan including PVC clamp complete all as specified and as directed by the Engineer-in-Charge. Make :- Epcos/Bajaj/Havells/Crompton

S&F ein repair ball bearing suitable for ceiling fan 1200/1400mm sweep complete all as specified and as directed by the Engineer-in-Charge. Make :- SKNNBC/TATA

M&L for rewinding of ceiling fan 1200/1400mm sweep with super enameled copper wire of existing gauge including varnishing and drying complete reassembling & testing complete all as specified and as directed by the Engineer-in-Charge.

S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers including taking down old unserviceable exhaust fan and deposited to MES store yard complete all as specified and as directed by the Engineer-in-Charge.

S&F ceiling fan downrod suitable siae upto 03 feet with GI hooks as per requirements of site of any size complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two runs of single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 2.50 Sqmm (FRLSH) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 2.50 Sqmm (FRLSH) of continous earth wire green in colour complete all as specified and directed by Engineer-in-charge. Note :- Two runs of 2.50 Sqmm cable & one run of 2.50 Sqmm cable continuity earth and one run of PVC conduit with all necessary accessories shall be paid as one unit length

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium condutor of size 16 sq mm 2 core including taking down old unserviceable cable complete all as specified and directed by Engineer-in-charge .

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium condutor of size 35 sq mm 3.5 core including taking down old unserviceable cable complete all as specified and directed by Engineer-in-charge.

Excavation in hard dense soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable and getting out complete all as specified and directed by Engineer-in-charge .

Excavation in Soft/Desintegrated rock not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable and getting out complete all as specified and directed by Engineer-in-charge .

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in Soft/Desintegrated rock complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated Soft/Desintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair HDPE DWC pipe ISI Marked fixed on walls, ceiling or in floors, trenches etc for cable complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair GI Tubing light grade 50 mm dia in trenches on pole for protection of cable protection complete all as specified and as directed by the Engineer-in-Charge.

M&L for road cutting and making good with PCC 1:3:6 type-C-2 (using 40mm graded stone aggregate) complete all as specified and as directed by the Engineer-in-Charge.