Development of Electrical Infrastructure to provide electrical connection to left out households in Cluster 2 Bahraich, Balrampur, Shrawasti, MVVNL under RDSS

Overhead 11 kV Line

8.5 m/180 kgs PCC Poles (PCC Pole as per state practice)

Foundation of PCC Supports as per scope of works, cement concreting (1:3:6) (0.268 Cmt for each support)

Stone pad for supports as per scope of works & drawing (300x300x75 mm )

11KV V-Type Cross-arm (M.S Channel 75X40x6mm) welded with MS angel (50x50x6) (weight-10.37 kg) with bolts and nuts

Cross arm holding clamps (MS Flat-50x8 mm) (weight-1.33 kg) with bolts and nuts

F- Bracket MS flat (50x8 mm) (weight- 1.56 kg) with nut and bolts

Cut point top channel (100x50x6 mm) of length 230 mm along with clamps and nut & bolts

Cut point bottom channel (100x50x6 mm) of length 1150 mm along with clamps nut & bolts

Tapping horizontal cross arm (100x50x6 mm) of length 1020 mm along with calmps (50x8) and nut and bolts

Tapping top channel (100x50x6 mm) of length 256 mm along with calmps(50x8) and nut and bolts

DP Top channel (Channel-100X50x6mm) 2240 mm long with bolts and nuts

Horizontal Belting Angle (Angle-50x50x6 mm) 2240 mm long with bolts and nuts

Cross bracing Angle (Angle-50x50x6 mm) 2500 mm long with bolts and nuts

Belting clamp-Top clamp (Flat-50x8 mm) (weight 1.4 kg) with bolts and nuts

Belting clamp-Bottom clamp (Flat-50x8 mm) (weight 1.5 kg) with bolts and nuts

Fish plate for jumpering

6/2.59 + 1/2.59 mm (30 sqmm Al. Area) ACSR weasel conductors

PG clamp for weasel conductor

Jointing sleeves Aluminium

Aluminium binding wire and tape

11 KV polymer Disc insulator 45 KN (B&S type) along with suitable hardware fittings

11 KV Polymer Pin Insulators 5 KN with nuts

Earthing of pole by earthing coil (with Salt & Charcoal)

8 SWG GI wire for pole,DB earthing with GI nuts, bolts & washers

MS Danger board with Back calmps & nuts and bolts as per Technical specification

Anti-climbing device-1.5 kgs with supporting clamp, 2.5mm dia (12 SWG) galvanized barbed wire on each 11 kV support as per scope of works & TS

Numbering and scheme details on each pole as per Technical specification and scope of work

Road/Line Crossings

V-cross arm supporting channel (100x50x6 mm), 3000mm long with holding clamps, bolts and nuts.

11KV V-Type Cross-arm for supporting channel (M.S Channel 75X40x6mm) welded with MS angel (50x50x6) (weight-10.37 kg) with bolts and nuts

Guarding Cross arm (75x40x6 mm) 2210 mm long with eye bolts (16mm dia)

Back clamp for guarding cross arm (50x8 mm) (weight- 1.15 kg) with nut & bolts.

Cross arm holding clamps (MS Flat-50x8 mm) (weight-1.33 kg) with bolts and nuts

6 SWG GI wire along the span

8 SWG GI wire across the span

12 SWG GI wire for binding

Distribution transformers

9 M / 400 kgs WL PCC Poles (PCC Pole as per state practice)

Foundation of PCC Supports as per scope of works, cement concreting (1:3:6) (0.268 Cmt for each support)

Stone pad for supports as per scope of works & drawing (300x300x75 mm )

Transformer Top channel (100x50x6mm) 2800 mm long and nuts & bolts

AB switch mounting channel (100x50x6mm) 2800 mm long with nuts & bolts

Back clamp for AB switch mounting channel(50x8mm)- (weight-1.8 kg) with nuts & bolts

DO fuse mounting channel (75x40x6mm) 2800 mm long with nuts & bolts

Back clamp for DO fuse mounting channel(50x8mm)- (weight-1.9 kg) with nuts & bolts

Transformer mounting channel (100x50x6mm) 2800 mm with nuts & bolts

Transformer mounting channel support (50x50x6mm) 500 mm long with Nuts & bolts.

Transformer Belting angle (50x50x6mm) 2800 mm long with nuts & bolts

Transformer Belting angle support (35x35x6 mm) 500 mm long with nuts & bolts

11 KV polymer Disc insulator 45 KN (B&S type) along with suitable hardware fittings

11 KV Polymer Pin Insulators 5 KN with nuts

11/0.4 kV Distribution Transformer 25 KVA Three Phase aluminum wound DTR with high grade CRGO Core (Energy Efficiency Level-1 specified in IS 1180 (Part-1):2014 as per latest amendment 4 March 2021)

ACSR weasel counductor for Jumpering

Bimetallic connector for HT & LT side of the transformer

PG clamp for jumpering

LT Distribution box polyester sheet moulding compound (SMC) for 25 kVA Distribution transformer with arrangement of suitable bus-bars & MCCB's as per scope of works of SBD

Back clamp support for LTDB ( 65x8 mm)

1Cx35 sqmm 1.1KV XLPE cable with suitable lugs and glands and cable ties

Clamps for LT service cable support

9 kV, 5 kA distribution class LA

11 kV, 3-ph, 200 A, 3 Pin type Vertical Mounting type AB Switch along with Support Insulators, Base Channel, down Pipe, operating handle and support, etc. complete as per technical specifications, scope of works and approved drawings

11 kV, 3-ph, Drop Out fuse Set (set of 3 units) along with Support Insulators, Base Channel, fuse barrel etc. complete as per technical specifications, scope of works and approved drawings

GI Earthing pipe of 40 mm dia & 3000 mm long as per IS 1161

GI wire 8SWG

GI flat (25x3 mm)

MS Danger board with Back calmps & nuts and bolts as per Technical specification

Anti-climbing device-1.5 kgs, 2.5mm dia (12 SWG) galvanized barbed wire on each Pole 11 kV support as per scope of works & TS

Numbering and scheme details on each pole as per Technical specification and scope of work

LT line

8.5 m/180 kgs PCC Poles (PCC Pole as per state practice)

Foundation of PCC Supports as per scope of works, cement concreting (1:3:6) (0.268 Cmt for each support)

Stone pad for supports as per scope of works & drawing (300x300x75 mm )

Single phase Glass Fiber Reinforced Polyester Sheet Moulding Compound (SMC) Pole top distribution box with calmps (40x3 mm) and nut & bolts

Three phase Glass Fiber Reinforced Polyester Sheet Moulding Compound (SMC) Pole top distribution box with calmps (40x3 mm) and nut & bolts

2Cx25 sqmm XLPE aluminium conductor cable for single phase DB incomer

4Cx35 sqmm XLPE aluminium conductor cable for Three phase DB incomer

Earthing of pole by earthing coil (with Salt & Charcoal)

8 SWG GI wire for pole,DB earthing with GI nuts, bolts & washers

Aerial Bunched XLPE Cable 1X25 (Ph) + 1X25 ( Bare messenger cum neutral) + 1x16 (insulated Street lighting) sqmm

Aerial Bunched XLPE Cable 3X50 (Ph) + 1X35 ( Bare messenger cum neutral) + 1x16 (insulated Street lighting) sqmm

LT pole clamp (50x8mm) (2.56 kg) with Nut and bolts

LT Eye hook

suspension clamp

Dead end clamp

Insulation Piercing connectors/Connector type-I (AB cable to AB cable)

Insulation Piercing connectors type-II (AB cable to Service cable)

PG clamp for bare messenger cum neutral wire of LT Aerial Bunched Cable (ABC)

Length of 2cx6 sqmm Service Armoured cable (in km.)

Stay Set (Galvanised) with 50x8 mm stay clamps, guy insulator , anchor plate (200x200x6mm) , nut bolts, 1 Nos turn-buckle, 1.8 m long, 16 mm diameter solid GS stay rod & 7/3.15 mm dia GI stranded wire complete as per technical specification, approved drawings and scope of work including foundation of stay support in each stay set as per scope of works

Stay Rod 16x1800 mm complete as per Technical specification, scope of work and tender drawing

Stay Wire 7/10 SWG

Stay Clamp- (Flat-50x8 mm) (weight-1.5 kg)with bolts and nuts

Stay Guy insulator LT

Stay Guy insulator HT (11 KV)

stay thimble

Hellically formed end fitting

Concreting of Stay Rod ( 0.2 cmt cement concreting in mixture (1:3:6)