SPL REPAIR TO BLDG NO P 1 JCO MD ACCN AT RIDGE AREA AND BLDG NO NP 49F NP 50F OF STN NCC OFFRS STAFF ACCN AND PROVN OF COMPRESSOR SHED AND CERTAIN MINOR WORK UNDER GE SATWARI

Amount

Demolition of cement concrete (unreinforced) ground floor to 2nd floors and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing surface with neat cement slurry with 3.0 kg of cement per sq. metre, removing serviceable tiles to store and rubbish off the Cantt area complete all as directed

M&L glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 complete all as specified.

M&L Non-skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified.

Ditto all as per item No 05 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete all as specified.

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified.

Ditto all as per item No 07 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete all as specified.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 complete all as specified.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.

M&L rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4, rendering is to be finished even and fair without using extra cement (up to 2nd storey with necessary scaffolding) complete all as specified.

M&L rendering cement plaster, 15 mm thick on fair faces of brick/concrete surfaces of wall in cement mortar 1:6 finished even and smooth with out using extra cement complete all as specified.

M&L rendering 10 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cement complete all as specified.

M&L machine cut kota stone slab flooring 18-20 mm thick over and including cement screed bed laid and jointed cement screed bed laid and jointed with grey camant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for tread of staircase over and including 15mm thick screed bed in CM 1:4 all as specified and directed

M&L machine cut kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase over and including 10mm thick fair and even plaster in CM 1:4 all as specified and directed.

M&L rendering 15mm thick in CM 1:3 as in sunken floors without extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L applying a coat of bituminous primer conforming to IS-3384 on prepared surface of roof/ sunken slab after drying of primer apply APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by forced torched application and finally apply a coat of hot blown 85/25 graded bitumen conforming to IS-702 @ 1.2kg /sqm of plaster surface.

M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan ( Up to 2nd floor) filling and mass concrete complete all as specified and directed by Emgr-in-charge.

M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats complete all as Specified.

S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

S&F factory made, plain framed, panelled shutter (two Panel) 35mm thick, 2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated complete all as directed by Engr-in-Charge.

S&F 35mm thick 2nd Class hard wood gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars, stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified

S&F Flush shutters, 35 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. Note :- Sampel approved by Engr-in-Charge or GE.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any discription ground to 2nd floors and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

M&L pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

S&F prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed by Engr-in-Charge.

S&F continuous (piano) hinges, heavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified.

S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified. (ISI Marked)

S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F Aluminium handles, fabricated type, anodised Size 100mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F Aluminium alloy, anodised, sliding door bolt Size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S & F hasp & staple safety type aluminium anodised with mild steel hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length.

S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

S&F mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed. Note: For measurement superficial area in elevation shall be measured.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. One side prelam and other side plain18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufactuer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 18mm thick Celuka PVC Ply for Shelf/Partitions /Drawer and also manufacturer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 5mm thick PVC of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 5mm thick PVC sheet paneling for back side (wall side) and also manufacurer's test report and test certificate is mandotary with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F 100mm size Stainless steel handle complete all as specified and as directed.

S&F ball rolling sliding channels of size 450mm length fixed in cupboards with screws as in drawers

S&F Auto hinges of size 150mm length fixed in cupboards with screws for holding stainless steel baskets as in drawers

S&F self adhesive tape of 18/19mm width , hot pressed & pasted on sides & bottom of edges of cupboards shutters

S&F steel fasteners of size 75mm long drilled and fixed to walls

S&F 50mm dia and 75mm long steel supports fixed with bolt at bottom of cupboards box all as specified

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

M&L brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge

M&L brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and as directed by Engineer-in-charge

M&L brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (ii) PCC block for embedding lugs.(iii) Guard bar for grills shall paid separately.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; framed balusters, walk ways; railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F 4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto second storey with necessary scaffolding), all as specified.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified fixed with stainless steel wire staples.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Complete removal of existing water proofing treatment of any description incld under layer, taking down of cement plaster/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed .

M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc

Dismantling water tanks and removing to store of water storage tanks (Cap. 500 ltr to 1000 ltr ) complete all as specified and directed by Engineer-in-charge.

S&F Rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical with closed top) triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed.

S&F in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified.

S&F in repair CP Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified.

S&F in repair angle valve with wall flange, cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F in repair Stop valves, cast copper alloy,fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

S&F in repair CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair Chromium plated, towel ring, complete all as specified.

S&F in repair stainless steel shop dish holder complete all as specified.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge.

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified.

S&F in repair brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified.

S&F in repair sinks with drainage board made of stainless steel 1.00 mm thick for kitchen with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

S&F kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete.

S&F in repair vitreous china, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, complete all as specified and as directed by Engineer-in-charge.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified. (Rate of including in taking out and removal of old WC seat unhygienic condition)

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good,cutting n.exc 10cm girth in brick walls.

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR), bends for 75 mm bore, complete all as specified and as directed by Engineer-in-charge

Supply and fixing, UPVC (SWR) , bends with access door for 75 mm bore, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC branch piece, single (single 'Y') with access door for 75 mm bore complete all as specified and directed.

Supply and fixing, UPVC branch piece, single (single 'Y') with access door for 110 mm bore complete all as specified and directed.

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore , complete all as specified and as directed by Engineer-in-charge

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed by Engineer-in-charge

S&F UPVC (SWR), reducers 110 mm dia complete all as specified.

S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

M&L for providing, cement concrete 1:2:4 type B-1 (using 20mm graded aggregate ), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, with greay cement and pigment, set, jointed and pointed in neat cement slurry in floors and laid over and including 20mm thick screed bed in CM 1:4 etc complete all as specified and as directed

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 75mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified.

M&L for precast cement concrete louvers and jallies, 40 mm thick (1:2:4) type B-0 (using 12.5 mm graded aggregate ) set in cement mortar 1:6, including all mouldings and dismantling old U/s broken Jallies at site, complete all as specified.

M&L for 25 mm thick cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4, type B-1, (using 20.00 mm graded crushed stone aggregate) as in floor finished rough complete all as specified and directed.

M&L for repairing of concrete surfaces such as balcony, chajjas, upward or downward facias, column, pillar, ceiling and similar items with plain cement concrete 1:2:4 type B-0 or rendering 10-15mm thick as per site requirement in CM 1:3 without using extra cement finished even and fair complete all as specified and directed (Up to fourth storey bldgs and including necessory formwork and scaffolding required as per site condition also taking down or dismantling as required at site.

Complete removal of existing treatment including washing, rubbing down with sand paper and stopping of painted surfaces including preparation of old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying one coat of weather proof exterior emulsion (APEX) making good uneven surface/holes with Birla wall care putty coloured in same shade where ever required etc (up to 2nd storey with necessary scaffolding) complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Preparation of new plastered or unplastered surfaces of walls to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

Complete removal of existing treatment including washing, rubbing down with sand paper and stopping of distempered and painted surfaces including preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion over and including one coat of primer over two coats of Birla wall care putty 1 to 2 mm thick on plastered surfaces, preparatory to distempering complete all as specified and as directed by Engineer-in-charge.

Preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of cement based paint over and including one coat of primer (up to 2nd storey with necessary/scaffolding) complete all as specified and as directed by Engr-in-charge.

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying two coats of cement base paint on walls, pillars, cornice etc (upto 2nd storey with necessary scaffolding) complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified.

M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm preparation and necessary filling by chalk putty as and where requered to make surface even and smooth complete all as specified including

M & L for preparation of old decorated brick /concrete, plastered /un-plastered surfaces of walls, pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed.

M & L for preparation of old decorated brick /concrete, plastered /un-plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots & rubbing with sand paper and and applying one coat of white wash on ceiling, complete all as specified and directed.

M & L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with dustfree sand paper mechanised scrapper as per paint manufacturer specifications and applying one coat of premium distemper on old decorated wall surface and necessary filling of wall care putty on uneven surface as and where required all as directed by Engineer-In-Charge.

M & L for preparation of old decorated plastered /concrete/ brick surfaces of walls (up to 4th storey with necessary scaffolding) and applying one coat of cement based paint on old decorated surfaces complete all as specified.

Supply only Water proofing compound liquid.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in hard and dense soil complete all as specified and as directed.

M&L Hardcore of guage n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surfaces complete all as specified and as directed.

M& L for 75 mm thickness PCC 1:4:8 type D-2 (40 mm graded crushed stone aggregate) complete all as specified and directed.

M&L for 100 mm thick PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in hand standing complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver complete all as specified and as directed.

Excavating in post holes (or similar holes) in any type of soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25 cm, watering and removing surplus soil to a distance n exc 50m and making good surface.

M&L PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in mass concrete in foundation) complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standard rails, straining bolts etc including provision of binding wire complete all as specified and as directed.

Supply only chain link MS galvanised fencing of mesh size 100 mm x 100mm dia of wire 4 mm, complete all as specified and directed.

S&F MS angle iron posts and struts in fencing, including cutting top to shape as directed drilling holes welding and notching for wire etc and flat iron fillets for securing wire mesh including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating (AZ 150 micron) GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F steel work in tubular trasses including special shaped washer using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long

Taking down carefully aluminium conductor point wiring (light, fan, socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN /TPN along with MCB's

Taking down of unsv Sub main wiring of any size

M & L for complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One Light / Fan/ Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

(d) One bell/ buzzer point controlled by one, complete all as specified and directed.

(e) One Light point controlled by one, Two way switch 6 Amp complete

Ditto all as per Srl item No 152 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, Two way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Supply and fix ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fix modular bell push with indicator polycarbonate materials ISI markrd 1 module, 6 Amps 240 Volts.

Supply and fix musical door bell, AC 230 Volts single phase.

Supply and fix LED light fitting 1 x 18Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrengenment all as directed by Engr in chage. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fix of lamp holder, PVC /Polycarbonate type with back plate for batten fitting .

Supply and fix LED lamp suitable for B22 holder of capacity 7 Watt.

Supply and fix energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed.

Supply and fix Distribution Board (SPN) double door 12 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated, Earth Bar, neutral Bar Door Earthing.

Supply and fix MCB SPN complete 40 to 63 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix MCB Single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed

Supply and fix sub main wiring with single core cable 2 x 6 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 6 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing ceiling fan complete with blade, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with fixing by anchor fastner of suitable size and hook/clamp and connected from ceiling rose/ connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, complete.

Supply and fix of exhaust fan, steel body AC single phase. 230 V of size 300 m sweep with, blades, and frame and louvers and including making of holes in wall, floor etc all as directed by Engr in charge.

Taking down and refixing of Ceiling fan of any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer, all as specified and directed by Engr-in-charge.

Taking down the existing electric meter of any capacity and make after disconnecting electrically and examine carry out the servicing and refixing including applying one coat of paint(outer box), testing in all respect for smooth running complete.

Taking down the existing unserviceable Geyser and after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the geyser by thoroughly cleaning the tank, thermostat, heatingelement and LED Lamp indicator, testing in all respect for smooth running and refixing complete all as directed.

Supply and fix sheet metal enclosure MCCB DB VTPN double door 4 way suitable for 415 V with 200 amps rated bus bar including flushed on walls and making good disturbed surfaces including taking down the old DB suitable for MCCB 4 Pole as incomer all as specified and as directed.

Supply and fix 4 Pole MCCB 100 Amp, 415 Volts with rupturing capacity 16 KA , complete all as specified and directed

M & L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply, laying for replacement of unserviciable underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured cable 25 sq mm 3.5 core cable confirming to IS-7098 Part-I (1988) with latest ammendments of sizes.

Excavation in trenches not exceeding 1.5m in width and not exceeding 1.5m in depth and getting out in any type of soil complete all as specifieds and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specifieds and directed.

Removal of excavated surplus material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specifieds and directed.

Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.

Supply & laying dry bricks over cable as mechanical protection layed flat with width equal to length of brick with sub class 'B' bricks complete all as specifieds and directed.

Material and labour for GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.

M/S RAJINDER GOODS TRANSPORT CARRIER

STAR CONSTRUCTIONS

M/S Raman Construction Co.

THAKUR BUILDERS AND CO

M/S ANIL MAHAJAN

M/S PARAMJEET SINGH

CELMAC REGD

M/S MOHAN LAL GUPTA