PROVN OF DG SETS OF VARIOUS CAPACITIES AND CERTAIN REVENUE AND MINOR WORKS AND ALLIED SERVICES UNDER AGE E/M OF GE (AF) TECH AREA AT AF STN AGRA

Amount

Supply, laying, testing and commissioning GI tubing medium grade with & including required GI fitting laid in trench/ wall/floor/ceiling/roof complete all as specified and directed for the following bore :-

(a) 40 mm bore

(b) 25 mm bore

Supply & fixing gun metal globe gate valve with iron wheel head, screwed both ends ISI mark for the following sizes all as specified & directed :-

(a) 40 mm bore

(b) 25 mm bore

Supply, lowering, commissioning & testing submersible pumping set with discharge capacity 80 LPM at 50M head single phase 230 volt AC electric driven 2900 rpm of minimum 1.5 HP complete all as specified and directed.

Supply & laying PVC insulated and PVC sheathed copper conductor cable 2.5 Sqmm, 3 core flat for 1100 volts AC including connecting with submersible motor to starter panel complete all as specified and direced.

Supply and fixing wall mounted cubical type panel board with locking arrangement, suitable for comprising of starter, condenser, volt meter, indicator lamp, Amp meter, MCB/cut out of suitable capacity for 1.5 HP single phase submersible pumping set including necessary fixing arrangement complete all as specified and directed.

M & L for 2 Nos MS clamp made out of 40mmx 6 mm thick FI for holding of 40 mm dia column pipe complete with suitable size 02 Nos nut, bolt & washers complet all as specified and directed.

M& L for well cap duly made out of 4 mm thick MS plate including making provision for passing GI column pipe of 40 mm dia complete all as specified and directed.

M&L for boring/drilling in any type of strata upto 100 mtr of 125 mm dia by any means including developing bore,flushing up to coming of clean water etc all as specified and directed.

Supply & lowering PVC casing pipe 110 mm dia ISI mark suitable for 6 Kgf/cm² pressure Plain/slotted as per site requirement all as specified and directed.

Supply,lowering and testing in bore welll 32 mm dia high density polythylene column pipe pipe ISI marked as per IS 49840 of 1995 metrial grade PE-63, pressure rating PN-10 and 32 mm dia , jointing material with HDPE fitting all as specified and directed..

M&L for point wiring complete with standard FRLS copper conductor 1.5 sqmm size (Nominal area) 1100 volts grade PVC insulated unsheathed FRLS multi stranded copper conductor cable in and including concealed PVC conduit ISI marked not less than 20mm dia including 1.5sqmm standard copper conductor PVC insulated unsheathed cable of green green colour as earth continuity connected to common earth dolly and all sunk/terminal boxes and each fitting/fixture, complete with all acessories and including cutting and chasing complete all as specified & as directed.

S&F switch piano, flush type 5 Amp, 240 volts complete all as specified & as directed.

S&F Ceiling rose surface bakellite 32.5x25mm surface type three terminal complete all as specified and directed.

S&F Exhaust Fan steel body AC 230 volts single phase 380mm 900 rpm sweep turbo force SP with blades frame and louverscomplete all as specified and directed.

Making of hole suitable for exhaust fan 380mm sweep complete all as specified & directed.

Supply,laying and fixing galvanized steel tubing of size 100 mm dia medium grade laid in trenches including all neccessory fitting complete all as specified and directed.

Supply,laying and fixing galvanized steel tubing medium grade of size 80 mm dia laid in trenches including all neccessory fitting complete all as specified and directed.

Supply,laying and fixing galvanized steel tubing medium grade of size 50 mm dia fixed to wall/ceiling including all neccessory fitting complete all as specified and directed.

M& L for brick masonary valve chamber of size 900x900x900mm (internal dimensions) with and including PCC 1:4:8 foundation, 150mm thick brick walls built in CM 1:6, PCC 1:3:6 type C-1 using 20mm graded stone aggregate coping 50mm thick, plastering 15mm thick in CM 1:4 to all internal and exposed surface including necessary excavation and earth work in any type of soil, MS sheet cover 3.15mm thickness alongwith angle iron frame of size 40x40x6mm with locking arrangement with necessary fixing materials like hinges, anchoring bolts etc (Valve chamber cover shall be opended in two halves) and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed .

Supply & fixing of cast iron body sluice valve ISI marked PN 1.6 and conforming to IS 14846 with stainless steel spindle of 100 mm bore complete all as specified and directed.

Supply & fixing of cast iron body sluice valve ISI marked PN 1.6 and conforming to IS 14846 with stainless steel spindle of 80 mm bore complete all as specified and directed.

Supply & fixing of non return valve ISI marked including complete fixing accessory of 80 mm bore size complete all as specified and directed.

Supply & fixing gun metal globe gate valve with iron wheel head, screwed both ends ISI mark for 50mm bore size all as specified & directed.

M & L earthing complete with Gl electrode 600x600x6.00mm thick buried directly in ground vertically in pit of depth not less than 3.75 mtr below normal ground level with top edge of the earth plate not less than 3.25 mtr below normal ground level connected to Gl wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of brass connected all as specified including excavation and earth work and disposal of surplus soil incl 20 mm Gl tubing light grade and necessary fitting for protection of Gl wire incl laying of charcoal, dust and common salt, PCC (1:2:4) type Cl using 20 mm graded stone aggregate earth pit with 40x40x6mm MS angle iron frame, RCC cover 40mm thick (1:2:4) type B0 using 12.5mm graded stone aggregate reinforced with 8mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6:) internally and upto 150mm below ground level externally. funnel with wire mesh 20mm dia Gl pipe for watering complete all as shown on electrical plate No.3 of SSR Part -1 2009 and connected in earth test incl testing completed all specified and directed. NOTE:- Cost of earth lead and protection pipe upto 7.5M shall deemed to be included in quoted rate.

S&F MCCB four pole AC 415 volts, 50 Hz, thermal magnetic setting type of capacity 63 Amps having breaking capacity 25 kA complete all as specified and directed.

Demolition of PCC/Black bitumin road of any description and in any position not otherwise specially provided for complete all as spciified and directed.

M&L PCC (1:2:4) type B2 (using 40mm graded aggregate) as in surface,channels and drains complete all as spciified and directed.

Supply & lay GI tubing light grade 40 mm bore in trenches/floor etc for protection of cable complete all as spciified and directed.

M&L for Boring/drilling/bore well for inserting casing/ stainer pipe of 300mm dia by suitable method as prescribed in IS :2800 (Part-I) in any kind of soil strata including material / lowering / fixing of 300mm bore MS Pipe of suitable weight, plane/slotted as per site requirement complete all as specified and directed.

Development of tube well with compressed air and after with 25% extra capacity pumping set to pump muddy water.complete all as spciified and directed.

M&L for carring out Yeild test for bore well by continuoulsy pumping for 16 Hrs to determine pumping yeild complete all as spciified and directed

Supply and lowering submersible pump set of capacity 10 HP,3 phase,50 Hz, 480 LPM at 78 Mtr Head, delivery size 75 mm,stage 10 and suitable for 200 mm dia bore well complete all as specified and directed.

S&F fully automatic star- delta starter of relay range 14-21 Amps of capacity suitable for and upto 10.0 HP motor, AC-3duty, 415 volts, 50 Hz, three phase including fixing arrangement complete all as specified and directed. Make : L&T or equivalent make of Havells/ Crompton Graves/C&S

M & L for 2 Nos MS clamp madeout of 80mmx 12 mm thick FI for holding of 80 mm dia column pipe complete with suitable size 02 Nos nut, bolt & washers complet all as specified and directed

M& L for well cap duly made out of 4 mm thick MS plate for bore upto 250 mm dia including making provision for passing MS column pipe of 80 mm dia complete all as specified and directed by Engineer-in-charge.

S& F 80 mm bore MS Column pipe, heavy grade ISI marked 3 m long including heavy duty MS flanged at both ends,nuts , bolts , washers & 3 mm thick rubber sheet etc complete all as specified and directed.

Supply and laying or fixing or passing in well/ borewell 1100 volts grade heavy duty, PVC insulated and PVC sheathed mutistranded copper conductor submersible cable of size 10.0sqmm 3 core flat including connection to submersible motor/ starter panel with & including necessary jointing materials if required and testing on completion complete all as specified and direced.

Supply, commissioning erecting and testing complete of manufacturer or OEM manufactured, statiic silient (sound proof enclosure) Disel Engine driven Generating set of capacity 15 KVA, water cooled, 415 volts (AC three phase, 4 wire system of supply) 50 Hz at power factor 0.8 minimum. The DG set shall consists of diesel engine coupled to a matching alternator, through flexible coupling and mounted on common base frame and complete with control panel standardized by manufacturer, fuel tank with mounting arrangements and inlet, outlet return inlet oil arrangements, exhaust pipe complete and suitable for conditions prevalent at Agra (capacity of engine, alternators shall worked out taking allderating factors into consideration) including PCC foundation (of suitable size for trolly) and DG should be mounted on trolly complete all as specified and directed, including all feature tol comply with latest CPCB guidelines and comprising of followings all as specified and directed:-

DIESEL ENGINE : Diesel engine 1500RPM, direct injection, multi cylinders, four stroke, conforming to conforming to IS:100001/ISO3046/BS:649/BS:5514 amended upto date, for continous running capable of taking 10% overload for one hour in 12 hour, water cooled, naturally turbo charged, capable of giving adequate BHP to drive Alternator capable of delivery 15KVA at outdoor atmospheric conditionxs at Agra ( Taking all derating factor into consideration) fitting with the following accessories subject ot the design of manufacturer:- (i) Dynamically balanced fly wheel. (ii) Air cleaner oil bath type (iii) Mechanical governor class 1A Flywheel with starter ring (iv) Dry exhaust manifold with suitable exhaust residential grade silencer to reduce the noise level (v) Radiator cooling (vi) Radiator fan with guard (vii) Vaccum indicator (viii) Fuel filter and fuel houses (ix) Fuel injection pump (FIP) (x) Fan and water pump assesembly (xi) Lub oil filter and pump (xii) Electric starting system with battery charging alternator and axial type started motor including adequate number of high capacity maint free lead acid bty 12 Volts DC 90AH as per manufacturer recommendation including inter connecting cables/leads with terminals complete with starting/stopping switch voltmeter, etc 01 set

(xiii) Engine safety shut down system against low oil pressure and high water pressure. (xiv) Exhaust gas driven turbo charge (xv) Oil filter (xvi) Lub oil cooler (xvii) Engine main manual with spare part list (xviii) Suitable designed acoustic enclosure as per CPCB regulations (xix) Any other item not included / specified but is a standard design of the manufacturer.

Engine insttrument panel : Engine instrument panel shall comprising of the following:- (i) Starting on /off switch. (ii) water temp auge. (iii) Hour meter cum RPM indicator (iv) Lub oil pressure gauge (v) Lub oil temperature gauge (vi) Battery charging meter (vii) Safety alarm against high water temp and lub oil pressure. (viii) Any other item not included/specified but is a standard design of the manufacturer.

ALTERNATOR shall be self excited, self regulated, brush less for 15KVA continous operation at the speed of 1500RPM at 415 volts, 50Hz three phase, 4 wire system with advance electronic voltage regulator to ensure high voltage accuracy with +1% with class H insulation and SPDP enclosure directly coupled with engine through flexible couping and conforming to IS-4722 complete-01 No. Note:- Alternator should be able to deliver output rating at actual site condition.

Common fabricated base frame for engine and alternator made from structural channel.

Bottom mounted (or as per manufactures design) steel fuel tank fabricated out of 14 SWG MS sheet of capactiy not less than 12 hrs continous operation inside canopy with fuel level guage, drain plug locking arrangements etc with and including GI pipe connections duly laid as per engineering practice complete all as specifided and directed.

Bypass arrangement by providing separate panel made out of 3mm thick CRCA sheet, outdoor type with connecting copper bus bar of suitable size from change over and set of 3 Nos indication lamp for R, Y and B and 2 Nos 4 pole on load change over switch front handle operated of capacity 63 Amp is to be installed near AMF panel complete all as specified and directed.

(i) Hour run meter. (ii) Any other item not included/ specified but is a standard design to the manufacturer.

Inbuilt AMF panel suitable for DG set 15 KVA as provided by OEM, alongwith all accessories complete all as specifided and directed.

Supply and install testing and commissioning trolly factory fabricated manufactured of MS channels/angle iron etc duly painted and recommended by manufacturer with 4 wheels, and one spare wheel of suitable size including all wheel rim and suitable size of tyre and tube inner with hydraulic jack, toe rod,four wheel system, spring loaded leaf spring based suspension system with provn of idling screw jack 04 nos for levelling of above Dg set including suitable size of cage with locking arrangements and suitable size shed for above item No-1 DG set including proper fixing of DG set complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n. exc 1.5m depth for laying of cable, errection of poles, stay and pipe line and getting out complete all as specified and as directed.

Returning & filling including spreading, leveling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Removal of surplus excavated soil to a distance n. exc 50 m above the starting point complete all as specified and as directed.

Supply & laying of best bricks locally available sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable complete all as specified and as directed.

M&L for sand coushioning with clean dry fine sand unwashed including gently punning around cable in trenches for cable protection complete and filling the sand in cable duct inside the sub station building complete all as specified and as directed. Note:- Punned thickness of sand shall be measured and paid for sand used in cushioning to cable.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as specified and as directed.

Supply and fix compact air insulated rising main with copper busbar 125 Amps including 63 Amp MCCB,4pole as incoming, with breaking capacity of 25 KA and IP 54 protection complete all as specified and directed.

M&L for earthing complete with galvanised steel plate electrode 600mmx600mmx3.15 mm thick buried directly in ground (earth pit not less than 3.00 Mts deep below ground level with top edge of the plate not less than 2.25 Mtrs below ground level connected to glavanised iron strip 25 x 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of copper strip incl laying of charcoal dust and common salt PCC (1:2:3) type C-1 using 20mm graded stone aggregate earth pit with 40x40x6mm MS angle iron frame, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6 mm dia round bar @ 75mm C/C both ways with MS handle 12mm dia, plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally, PGI funnel with 20mm dia GI pipe for watering and wire mesh complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test incl testing complete all as spciified and directed. NOTE:- Cost of earth lead and protection pipe upto 7.5M shall deemed to be included in quoted rate.

Supply and fix ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps complete all as specified and directed.

Supply and fix refrigerator, electric driven (single phase), capacity 400 Litres .BEE 5 star rated complete all as specified and as directed.

Supply and connecting 1 KVA voltage stablizers automatic dontrol withtime delay relay 2 to 3 minutes over load/ever voltage cut off having input voltage range 130 to 300 volts and out put voltage 230 volts + 10 % single phase AC 50Hz Wall mounted .Model VCDW 01160 Make-Volina/V-Gaurd/Atlas

M&L for point wiring concealed type with 1.50 sqmm PVC insulated, unsheathed, single core, multistranded copper conductor cable 1100 volts grade with and including 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, pressed steel terminal box made of 1.2mm thick MS sheet/anodised steel box, painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc & making good the disturbed surface by applying putty & matching with colour to the adjoining wall for the one light/ fan/ exhaust fan point controlled by one piano type switch 5 Amps single pole one way complete all as specified & directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including PVC casing & caping ISI marked not less than 25mm width with its accessories or drawn in and including PVC rigid conduit not less than 20mm dia with its accessories, surface type, including one run of single core FR PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0sqmm as earth continuity and connected of common earth dolly complete all as specified & directed. Note:- Two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC casing & caping or PVC conduit including its accessories shall be measured and paid one unit length.

M&L for factory made sheet metal enclosure 240 volts, 4 ways with 200A rated bus bar, SPN, double door type suitable for housing MCB/Isolators and fixed the same on & including mild steel hold fasts of suitable size & shape after grouting the hold fasts in the wall with and including PCC (1:2:4) type B1 using 20mm graded stone aggregate complete all as specified & directed.

Supply & fix MCB, SP, AC, 240 volts of 06 to 32 Amps capacity "C" series and making connections complete all as specified & directed.

Supply & fix Isolator, SPN, AC, 240 volts of 6-40 Amps for inductive load connected through cable lugs of suitable size, complete all as specified & directed.

Supply & fix switch piano, flush type single pole, one way 15/ 16 Amps, 240 volts complete all as specified & directed.

Supply & fix socket outlet 2 in 1, 3 pin 5 Amps and 3 pin 15 Amps, flush universal type complete all as specified & directed.

Supply, commissioning erecting and testing complete of manufacturer or OEM manufactured, statiic silient (sound proof enclosure) Disel Engine driven Generating set of capacity 62.5 KVA, water cooled, 415 volts (AC three phase, 4 wire system of supply) 50 Hz at power factor 0.8 minimum. The DG set shall consists of diesel engine coupled to a matching alternator, through flexible coupling and mounted on common base frame and complete with control panel standardized by manufacturer, fuel tandk with mounting arrangements and inlet, outlet return inlet oil arrangements, exhaust pipe complete and suitable for conditions prevalent at Agra (capacity of engine, alternators shall worked out taking allderating factors into consideration) including PCC foundation (of suitable size leaving at least 0.5m all around for ease of movement and 0.5m height), anti-vibration pads complete all as specified and directed, including all feature tol comply with latest CPCB guidelines and comprising of followings:-

DIESEL ENGINE Diesel engine 1500RPM, direct injection, multi cylinders, four stroke, conforming to conforming to IS:100001/ISO3046/BS:649/BS:5514 amended upto date, for continous running capable of taking 10% overload for one hour in 12 hour, water cooled, naturally turbo charged, capable of giving adequate BHP to drive Alternator capable of delivery 62.5 KVA at outdoor atmospheric conditionxs at Agra ( Taking all derating factor into consideration) fitting with the following accessories subject ot the design of manufacturer:- (i) Dynamically balanced fly wheel. (ii) Air cleaner oil bath type (iii) Electronic Governor class 1 A with back up Mechanical governor class 1A Flywheel with starter ring (iv) Dry exhaust manifold with suitable exhaust residential grade silencer to reduce the noise level (v) Radiator cooling (vi) Radiator fan with guard (vii) Vaccum indicator (viii) Fuel filter and fuel houses (ix) Fuel injection pump (FIP) (x) Fan and water pump assesembly (xi) Lub oil filter and pump

(xii) Electric starting system with battery charging alternator and axial type started motor including adequate number of high capacity maint free lead acid bty 12 Volts DC 180AH as per manufacturer recommendation including inter connecting cables/leads with terminals complete with starting/stopping switch voltmeter, etc 01 set (xiii) Engine safety shut down system against low oil pressure and high water pressure (xiv) Exhaust gas driven turbo charge (xv) Oil filter (xvi) Lub oil cooler (xvii) Engine main manual with spare part list (xviii) Suitable designed acoustic enclosure as per CPCB regulations (xix) Any other item not included / specified but is a standard design of the manufacturer.

Engine insttrument panel : Engine instrument panel shall comprising of the following:- (i) Starting on /off switch. (ii) water temp auge. (iii) Hour meter cum RPM indicator (iv) Lub oil pressure gauge (v) Lub oil temperature gauge (vi) Battery charging meter (vii) Safety alarm against high water temp and lub oil pressure. (viii) Any other item not included/specified but is a standard design of the manufacturer.

ALTERNATOR (Make: Kirloskar electric co/ Crompton/ Stemford) shall be self excited, self regulated, brush less for 62.5 KVA continous operation at the speed of 1500RPM at 415 volts, 50Hz three phase, 4 wire system with advance electronic voltage regulator to ensure high voltage accuracy with +1% with class H insulation and SPDP enclosure directly coupled with engine through flexible couping and conforming to IS-4722 complete-01 No. Note:- Alternator should be able to deliver output rating at actual site condition.

Common fabricated base frame for engine and alternator made from structural channel, jerk proof PCC 1:2:4 mix type B1 foundation including adequate number of suitable anti-vibration pads all as per manufacture recommendations is deemed to be included in the unit rate quoted by the contractor.

Bottom mounted (or as per manufactures design) steel fuel tank fabricated out of 14 SWG MS sheet of capactiy not less than 12 hrs continous operation inside canopy with fuel level guage, drain plug locking arrangements etc with and including GI pipe connections duly laid as per engineering practice complete all as specifided and directed.

Bypass arrangement by providing separate panel made out of 3mm thick CRCA sheet, outdoor type with connecting copper bus bar of suitable size from change over and set of 3 Nos indication lamp for R, Y and B and 2 Nos 4 pole on load change over switch front handle operated of capacity 100 Amp is to be installed near AMF panel complete all as specified and directed.

(i) Hour run meter. (ii) Any other item not included/ specified but is a standard design to the manufacturer.

AMF CONTROL PANEL: Supply, fabricating and testing of factory mounted cubical automatic main failure panel with degree of protection IP-42 conforming to IS-2147, suitable for 62.5KVA capacity DG Set, fabricated using 14 Gauge CRCA sheet, powder coated comprising of suitable rated bus bar, internal wiring with control fuse, provn of connecting incoming and outgoing leads/ bus bar as approved with and including following accessories:- (i) Master switch for auto/manual/reset/off-01 No. (ii) Ammeter digital type, 96X96 mm with CT's-03 Nos aux supply 230 vlts, AC, acuracyclass 1. (iii)Voltmeter digital type 96x96 mm to read 0-500 volts supply 230 volts, accuracy class 1.0. (iv) Digital frequency meter-01 No aux supply 230 volts, AC (v) Push button start, stop, reset-01 No. (vi) Set of lamp for indicating load a set, low pressure, high cylinder temperature, load on mains, set fails at start, low oil presure. (vi) Battery charger connected to load. (vii) Transformer of adequate rating. (viii) Ractifiers (ix) DC ampere meter and voltmeter. (x) Fault accept / reset push button. (xi) Set of relays and contactor suitable for 63KVA DG Set for automatic start and automatically shut down of suitable rating and capacity adjustable to 70 to 100% and 2 Nos MCCB 4 pole, 100 Amp, 25 KA fixed on main supply and DG set supply. (xii) Make of AMF control panel shall be compaible as per OEM recommendations.

M&L for earthing complete with galvanised steel earth plate electorde 60cmx60cmx6.3 mm thick buried directly in ground vertically at a depth not less than 2.25 metre below normal grond legerl with top edge of eath plate at a depth not less than 1.5 metre below normal ground level, earth plate surronded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron strip of 32 x 6 mm as earthing lead (upto the body of the equipment) by means of bolts, nuts check nuts and washers made of galvanised iron and thimbles and protected by medium 40mm dia GI Pipe connected to main switch board or main control board or equipment and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC (1:3:6) Type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil returning filling in exvavation and earth work in any type of soil returning filling in approved soil adn disposal of surplus soil to a distance not exceeding 50m. all as specified and shown in electrical plate No 3 of SSR 2009 (Part-1) complete all as specified and as directed. NOTE:- Cost of earth lead and protection pipe upto 7.5M shall deemed to be included in quoted rate.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

S&F Laying GI Tubing of lights grade of 80 mm dia with all fittings and fixed complete to wall and ceiling or laid in floors complete al as specified and directed.

Supply and fix ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 125 Amps complete all as specified and directed.

S&F for sub main wiring with PVC insulated sheathed 2x6 sqmm and 1x4 sqmm single core FRLS cable standard copper conductor 1100 volt grade be use as continuous earth connected to earth down and incl into concealed PVC condute with all accessories complete incl making good to disturbed surface complete all as specified and directed. Note:- Two runs of 6.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC casing & caping or PVC conduit including its accessories shall be measured and paid one unit length.

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way complete all as specified and directed.

S&F MCB single pole and neutral 40 Amp 240V 'C' Series 10 KA complete all as specified and directed.

S&F MCB SP 6-32 Amps, 240V 'C' Series 10 KA complete all as specified and directed.

S&F outdoor type sheet metal bus bar chamber suitable for 200 Amps capacity having 04 nos aluminium bus bar of suitable size including angle iron mounting with PCC complete all as specified and directed.

Taking down old DG set of capacity 15 KVA from foundation including disconnecting all electrical connections and shifting and testing at another location including all necessary cable joining and including PCC foundation (of suitable size leaving at least 0.5m all around for ease of movement and 0.5m height), complete all as specified and directed.

Dismantling and taking out of Diesel Engine Generator Set 15 KVA capacity Make : Kirloskar/Ruston/Greaves or equivalent, air/water cooled situated at various pump houses/power houses and shifting to Manufactures authorised work shop or reputed work shop at Agra or another location for major overhauling by renewing the spare parts as required and re-installation incl.transportaion to original/differenr location including all necessary connections, connecting to alternator, including commissioning and testing and complete all as specified and directed. NOTES:- (i) Spare parts will be measured and paid separately as supply only (ii) Unit rate deemed to include Transport from site to workshop & back to site including neccessary T&P own arrangement complete. (iii) The quoted rates shall include labour element required for fixing of new spare parts under relevant item.

M&L for replacement of following parts of engine of 15KVA DG set. Note:- All spare parts shall be of Make Kirloskar/Ruston/ Greaves or equivalent,air/water cooled to suit the model of DG sets and to be procured from authorised dealer:-

Piston with pin and Circlips suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Piston ring set of suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Cylinder liner of suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Complete set of Joints suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Set of 'O' ring complete suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Cylinder head bolts suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Lubricant oil filter assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Lubricant oil filter element suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Fuel filter suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Fuel filter housing suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Sealing ring for push rod cover assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Over flow pipe assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Hose for air cleaner including hose clips suitable for engine which has to be renewed at site/workshop complete all as specified and directed. .

Banjo bolt for drain suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Nozzle suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Nozzle holder suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Fuel pipe complete including circlips suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Main bearing set suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Large end bearing for connecting rod suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Small end bush for connecting rod suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Connecting rod assembly without LE bearing and small end bush suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Exhaust and inlet valve suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Valve guide suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Cylinder head assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Roker cover (ALU) suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Roker arm suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Lubricant oil pump assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Set of oil seals suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

FIP Assembly suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Slipring suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Carbon brush with holder suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

Field winding of alternator suitable for engine which has to be renewed at site/workshop complete all as specified and directed.

M&L for PCC(1:2:4:) type B-1 using 20mm graded stone aggregate as in base support of struts and other similar location etc with and including all necessary form work complete all as specified an directed.

Demolition of PCC/Black bitumin road of any description and in any position not otherwise specially provided , etc complete all as specified and directed.

Balaji Associate

BRITE INDUSTRIES