SPECIAL REPAIRS TO BLDG NO P - 375 AND BLDG NO P - 391 (OR MD ACCN) AT MIC AND S UNDER GE(S) AHILYANAGAR

Amount

Demolition of cement concrete (un-reinforced) above ground floor exc. 15cm thick above ground level all as specified and as directed.

Demolition of brick work built in cement mortar of any description.

Demoltion of cement concrete ( un-reinforced ) in ground floors and paving n. exc 15cm thickness ( below or above ground level ) complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing, serviceable tiles to stone and rubbish off the premises all as specified and directed.

Demolition of cement concrete reinforced in, roof, floor, beam, stair case,landing,chajjas,and similar works above ground level (reinforcement cut as required to facilitate demolition) all as specified and as directed.

Dismantling of stone slabs and interlocking tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor complete all as specified and as directed.

Dismantling structural steel work including doors, gates,ladders,raillings etc but excluding framed trusses complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 sqm. each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm & n.exc 2 Sqm each and refixing in same opening after easing and adjusting etc complete all as specified and as directed.

Taking down shutter of any description exc 1 Sqm but not exc 2 sqm each complete all as specified and as directed.

Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed.

Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed.

S & F for Pipe Supporting Clamping - for Single Pipe of dia 15mm (1/2") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of : (a) Mono Bracket for 15 mm (1/2") pipe having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. (b) U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 15 mm (1/2") pipe, Wall distance 75 mm (3") - 1 Nos. (c) U Bolt Rubber Sleeve mounted of 15 mm (1/2") Pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 Nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory made pipe supporting system : CEPZ/2023/TD/03

Taking down of cement or cement lime plaster of any description on brick work or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete & removing debris as directed.

Demolition and breaking up of drain pipes (salt glazed ware or AC or reinforced cement concrete), set in cement mortar, dia of pipe 110/ 75mm complete all as specified and directed.

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed

M&L RCC M25 (using 20 mm graded stone aggregates) as in Foundations, footings, foundation beams; plinth beams; etc. all as specified.

M & L for mild steel TMT bars 5mm dia to 8 mm dia, as in stirrups, spacres and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L Use and waste of form work to sides of concrete foundation, footings, bases of columns, sides and soffit of plinth beams and similar work etc. for flat rough finished surface of concrete complete all as specified.

M&L for brickwork with old size fly ash bricks straight or curved on plan with mean radius exc 6 m built in CM1:6 complete all as specified and directed

M&L for 15 mm thick rendering in cement mortar 1:4 (using water proofing liquid) on other than fair faces of brick masonry surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed. (Note : Water proofing Liquid shall be measured and Paid separately)

Supply only Liquid water proofing compound all as specified and as directed

M&L for rendering 10 mm thick in cm 1:6 on brick/concrete surfaces finish even & smooth without unsing extra cement etc complete.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceiling finished the surface even & smooth without using extra cement complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L in repairs, for water proofing treatment to RCC roof slab, including parapet, comprising with the following treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the old concrete slab by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish n exceeding 100 mtr distance from starting point. (ii) Screed bed or bedding layer of 10 mm thick cement mortar 1:4 with mixing of WPC @ 3% by weight of cement or as per manufacturers instructions and surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm.

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 250 m and lift upto 1.5m all as directed.

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil upto 250m all as directed.

Excavation over areas n exc 1.50m in depth and getting out in any type of soil all as specified and as directed.

Returning filling-in including spreading, levelling, watering and well ramming in layers not exceeding 25cm using approved excavated soil all as directed.

Removal of excavated soil to a distance exc 250 mtr but n exc 500m and depositing where directed.

M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M & L for hardcore of gauge n exc 63mm deposited spread and levelled in layers n. exc 15cm thick watered and rammed to a true surface

M&L for 100mm thick, plain cement concrete, 1:4:8, type D-2, using 40 mm graded stone aggregate as in sub base of floors and pavings all as specified and as directed.

M&L for 60 mm thick, factory made precast cement concrete interlocking tiles/paver blocks (glossy finish/ rubber mat finish) of M-35 grade, conforming to IS-15658-2006, hydraulically pressed, grey colour with pigments, as in floor, laid over & including 25 mm thick sand cushion and including filling of interstices with fine sand complete all as specified and as directed. Note : Size, shape & pattern of tiles shall be as decided by GE.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular)area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc complete all as specified & directed.

M&L for glazed coloured ceramic tiles in vertical surfaces as dado of size 300x200x6-7mm/450x300x7mm thick set and jointed in neat cement and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on other than fair faces of brick work etc complete all as specified & directed.

M&L for non skid coloured ceramic mat finished tiles 7-8mm thick (square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (600X600 mm) in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

Ditto- all as per Item No. 41 above but as in skirting including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25mm thick as in cooking platform etc including cutting chases in brick wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed.

M&L for machine cut Kota stone flooring 18 to 22 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per item No 44 here in before but as in risers to steps and skirting laid over and including backing coat of 10mm thick in cement mortar 1:3 all as specified and as directed. Note : Risers provided to steps shall be in one piece

M&L for machine cut Kota stone slabs 18 to 22 mm thick as in treads of steps of stair case in single piece with 2 nos V groove cutting laid over and including 10 mm thick cement screed bed in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including, rounding and moulding edges, rubbing and mirror polishing complete all as specified and as directed.

M&L 18 to 20mm thick pre-polished granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/platform, gate pillars, cills etc or on vertical surfaces including vertical projection, including full round moulding the edge, laid over and including screed bed 15mm thick in cement mortar 1:4, jointing, pointing in white cement 1:2 using marble dust with admixture or pigment to match the shade of granite and rubbing, polishing to achieve mirror finish complete all as specified and as directed. Note : Colour and shade shall be as approved by GE.

S&F mild steel windows with side hung double shutters (one glazed and one for wire mesh) including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S&F mild steel framed work such as grill gratings etc with end of bars shouldered and/or riveted or forged into spikes,ladders and similar works including one shop coat of zinc chrome primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified.

S & F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or as approved) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a) Window frame: (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter: (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m) Note : Shade shall be as approved by Engineer-in-Charge.

S&F pressed steel doors frames of size 105 mm x 60 mm x 1.25mm thick, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed.

M&L for framed work as in doors or gates of angle/hollow section or other sections with gusset plate, rails, braces etc complete drilling for fixing of steel sheeting or other covering doors etc, to be prepared for hanging or sliding with and including either hooks and hinges and door fittings necessary rivetting/welding cutting, mild steel conforming to Fe-410-W (Gde E-250) quality-B and fixed complete all as specified and as directed.

S&F 30mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F 35 mm thick, second class hard wood glazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

M&L for 18/19mm thick prelaminated particle board exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber framed work including fixing arrangement complete all as specified

S&F first class soft wood beads, straight (any size ) for gauged joinery including mitres and removing old beads after tightening & nailing of wire mesh including two coats of synthetic enamel paint over one coat of pink primer all as specified and as directed.

S&F for Solid PVC door frame of size 50mmx47mm made out of 5mm wood grains Printed PVC sheet reinforced with MS square tube,suppling and fixing in opening as per specification & drawing.

S&F Fatory made solid panel PVC door shutter, 30mm thick(stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded feathered edges wood grain printed PVC sheet used instead of plain colour PVC sheet & 5 mm thick x15 mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10 mmx 10 (90 degree) used instead of exposed portion of PVC sheet beading suppling and fixing in the frame at site as per specification & drawing.

S&F SS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F in repairs SS wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Hacking out of old broken glass (any thickness ,size quality or description/ any height of bldg ) from wooden / metal frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or beads in square n.exc 0.50 sqm in each pane, of any description complete all as specified and directed.

S&F 3 mm thick frosted/figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

S&F 100 mm long SS butt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm as specified and directed.

S&F aluminum handle cast anodized 125mm size complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor over all length of cover plate 150 mm all as specified and directed.

S&F Magnetic catches brass boody and striking plate including necessary fittings fixed to cupboard shutter complete all as specified and as directed.

M&L for UPVC pipes, 15 mm bore (Pressure rating 10 kgf/cm²) laid in trenches / floors or fixed to wall in any length with all UPVC fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing complete all as specified and as directed.

M&L for UPVC pipes, 20 mm bore (Pressure rating 10 kgf/cm²) laid in trenches / floors or fixed to wall in any length with all UPVC fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing complete all as specified and as directed.

M&L for cutting chases for pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth all as specified and as directed.

S&F in repair 15mm bore dia stop valve, angle valve of cast copper alloy, fancy type CP long body (concealed type) high pressure screwed for iron pipe complete all as spd and directed.

S&F in repair 15mm bore dia stop valve, angle valve of cast copper alloy, fancy type CP high pressure screwed for iron pipe complete all as spd and directed.

S&Fin repair brass CP towel ring with bracket fixed wirh brass CP screws complete all as spd and directed.

S&F in repair 15mm bore brass CP center hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as spd and directed.

S&F , brass, chromium plated, health faucet, 15 mm bore and 1200mm long flexible connection pipe, wall mounted / hooked complete all as specified and as directed.

S & F stainless steel grating with square frame (grating thickness 1mm and frame thickness 1.5mm) of size 125mm (minimum) with waste hole complete all as directed.

S&F PVC Connection 15 mm size with PTMT nuts, 600 mm long, complete all as specified and as directed.

S&F brass chromium plated swivel shower rose, 125mm size, including shower arm, fixed to steel pipe and union complete all as specified and as directed.

S&F 15mm dia bib taps, fancy type, long body, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screed for iron pipe or brass ferrule, complete all as specified and as directed.

S&F two in one bib tap, chromium plated, cast copper alloy for fixing of Jet /hand faucet/health faucet including flange complete all as specified and as directed.

S & F in repairs vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm with integral foot rests (excluding flusing cistern) including traps & set in cement concrete as specified including flush pipe and connecting to trap complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 200 mm including CP coupling complete all as specified and as directed.

S&F CP Pillar tap (swan neek ) for kitchen sink secured for iron pipe and fixed with wash hand basine complete all as specified and as directed.

S&F 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve and handle including brackets complete all as specified and as directed.

S&F in repairs, kitchen plate rack of overall size 786mm x914mm x 254mm made out stainless steel sheet not less than 0.63mm thick, design and pattern as approved by GE and fixed to wall with wooden pluges with cromium plated screws and cup washers complete all as specified and as directed. Make : Prayag cat No P-348 or equivalent in Silver shine/ Suyog/ Blue Star.

S&F in repairs, mirror cabinet PTMT of size 600mm x 450mm (or nearest size) with magnetic locking arrangements, fixed with and including chromium plated brass screws and PVC rawl plugs complete all as specified and as directed. Make : Cat No. 554 of Prayag or of equivalent model in other makes as approved by GE

S&F rotational moulded polyethylene water storage tanks Triple layer (cylindrical vertical with closed top) of 500 litres capacity hoisted and fixed in position including 20 mm dia ball valve,high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and directed.

S&F in repair PTMT corner shelf in 3 tiers with CP guard brackets fixed with CP brass screws complete all as spd and directed.

S&F in repairs 20mm dia stainless steel curtain rod with brackets and knobs at both ends as per site requirement including taking down old curtain rods with accessories complete all as specified and as directed. Note: The cost of brackets & knobs shall deemed to be included in the quoted rate.

M & L for Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following (floor area of WC/Bath/toilet not exceeding 1.5 sqm) :- (a) After demolition of floor and lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square meter duly blended with & including water proofing compound. (c) 15mm thick (Average thickness) plaster in cement mortar (1:4) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non-woven fabric (weight not less than 150 gm/sqm (e) M&L for PCC 1:7:12 for fillin of sunken portion after conceling all membrane and sealing all joints to the entire with broken bats and light weight, and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts light grade, PCC 1:3:6, type C1 (using 20 mm graded stone aggregates) filling complete all as satisfaction of Engineer-in-Charge. Note- The rates include for drilling of the hole RCC @ 1.00 m centre to centre, to a depth to a length of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and grouting with cement slurry mixed with can bax 100 chemical with pressure grouting with minimm 3 Kg/Sqm complete all as specified and directed.

All as per serial item No 92 here-in-before but floor area of WC/bath-room/toilet exceeding 1.5 Sqm but not exceeding 3.0 Sqm.

S&F in repairs, vitreous china wash basin, white, angle back, size ,600mm x 480mm, excluding taps, waste pipe, chain plug and porcelain stopper but including pillar taps, 15mm bore dia, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, brackets, CP waste coupling 32 mm bore complete all as specified and as directed.

S &F in repair PVC waste pipe 40mm dia bore plain of standard length suitable for urinal Make Prayag, Symet all as specified and as directed

M&L for Plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone agg) as in bed to drain pipes including packing under and haunching against the pipes after they are laid and tested for 200 mm bore pipe complete all as specified and directed.

M&L for 200 mm bore reinforced concrete pipes of approved make, class NP2, laid and jointed complete with collars complete all as specified & as directed. Notes :- Purchase vouchers of RCC pipes shall be produced at the time of payment duly verified.

S&F 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in floor all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F 75 mm dia PVC (SWR) pipes single sockted any length with rubber ring joints complete all as specified and as directed

S&F 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F PVC (SWR) junction of 75 mm bore single, (single Y) equal or unequal all as specified and as directed

S&F 75 mm dia PVC(SWR) nahani/floor trap with grating including jointing to waste pipe with solvent cement complete all as specified and as directed.

S & F for Pipe Supporting Clamping - Single Pipe of dia 110 mm (4") down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of : a. Profile Bracket having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. b. Continuous Slotted "C" Channel with ribs to be used of size 250 mm (10") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. c. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3") - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10") - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4") CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : CEPZ/2023/TD/03

M&L for Preparation of newly plastered ceiling surfaces and applying a coat of average 2mm thick putty and two coats of oil bound distemper over a coat of primer complete all as specified .

M&L for complete removal of treatment on old surfaces of ceiling and applying a coat of average 2mm thick putty and two coats of oil bound distemper over a coat of primer complete all as specified .

M & L for complete removal of existing treatment on plastered or unplastered surfaces of walls and applying a coat of 2 mm thick (average) birla wall care putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper over one coat of primer complete all specified and as directed

M&L for applying 2 mm(Avg) thick of Birla/ JK wall care putty in new or old decorated surface of walls and sanding the surfaces till smooth finish is obtained for receiving finishes complete all as specified and as directed

M&L for preparation of new wall surface and applying two coats of oil emulsion distemper over a coat of primer complete all specified and as directed

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior acryclic emulsion weather coat paint, white or tinted, over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment on old decorated plastered suface of walls & applying two coats of ExteriorAcrylic Emulsion paint over one coat of primer including wall crack filler as required complete all as specified & directed by Engr in charge.

M&L for preparation of old painted surfaces and applying one coat of synthetic enamel paint on old wood or wooden based surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for preparation of old painted surfaces and applying one coat of synthetic enamel paint on steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for preparation of old painted iron/CI pipe surface of any description exceeding 10cm in width or girth and applying one coat of black bituminous paint complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of any shade over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new wooden surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of any shade over a coat of pink primer complete all as specified and directed.

S&F in repairs mild steel framed work as in hand rails and railing with end of bars shoulderd and/or riveted welded or forged into spikes, framed balusters etc and similar work conforming to Fe 290 Gde E-165 all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specifications & drawing complete all as specified and as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, bell push, holders, ceiling roses, pendants, regulators, sockets etc but excluding DBs, light fittings etc and making good disturbed surfaces of walls, floors etc. and matching with existing surface all as specified and as directed.

M&L for point wiring with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including concealed rigid PVC conduit (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC boards/bakelite sheets for mounting switches, sockets, fan Regulators, accessories etc as specified and as directed for one light point or one fan point controlled by one, one way switch NOTES: (a) Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW, BLUE for Earth-Green and Neutral-Black) (b) All points shall be earthed up to fixtures/ fittings (c) Rate includes cutting chases for conduits and for sinking of boxes and making good to walls and floors etc.

All as per serial item No. 123 here in before but for one 3 pin 6 Amp socket outlet point on same board with other switches including earth wire.

All as per item No. 123 here in before but for one 3 pin 6 Amp socket outlet point on independent board.

All as per serial item No. 123 here in before but for one light point controlled by 2 way switches.

All as per serial item No. 123 here in before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per serial item No. 123 herein before but with 2.5 Sqmm, PVC copper stranded cable FRLS type for phase, Neutral and earth for one 15 Amp, 6 pin socket on independent board.

S&F switch piano, flush button, 6 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.

S&F socket outlet, flush type, 3 pin, 6 Amp, multipurpose, 230 volts, single pole, one way suitable for 3 pin/2pin, 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, flush type, 3 pin, 6 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin) 6/16 Amps, 230V, AC. all as specified & as directed.

S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.

S&F ceiling rose, surface PVC 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.

S&F bell push, flush type, 6 Amp, single pole, 230 volts, white finish all as specified & as directed.

S&F switch piano, flush button, 6 Amp, single pole, 2 way, 230 volts, white finish all as specified & as directed.

S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.

S&F bell, AC, 230 volts, single phase complete all as specified and as directed.

S&F in repairs square profile LED lighting fixture with extruded polycorbonate,environmental friendly,energy efficient ready to use pack LED Tube light fitting 20 Watt with LED light source 6500k with uniform light output,with all accessories including its connection complete all as specified and directed by Engineer-in-charge. Make: HAVELLS AUSTRA LED batten 20W 6500 K Cat No LHLDESAARANC020 or equivalent of other makes specified.

S&F in repairs Inverter LED batten 20W 6500K with square profile and polycarbonate channel, lithium-Ion battery with charging time 8hours-10 hours, back up time up to 4 hours and surge protection up to 4KV. Make: HAVELLS PRIDE PLUS INVERTER BATTEN Cat No LHEXACP7FN1W020 or equivalent of other makes specified.

S&F in replacement inverter emergency LED bulb 12W 6500K with backup time upto 4 hours complete all as specified and directed by Engineer-in-charge. Make: Havells Cat part No. LED 12 W B22 CDL INVERTER BULB or of equivalent model in other makes of other makes specified.

S&F square profile LED lighting fixture with extruded polycorbonate, environmental friendly, energy efficient ready to use pack LED tube light fitting 10 Watt with LED light source 6500k with uniform light output,with all accessories complete with all as specified and as directed. Make : HAVELLS LED PRIDE PLUS NEO Cat No LHEXACP7IN1W010 or equivalent of other makes specified.

Supply and fixing in replacement factory made powder coated sheet metal enclosure, 4 way TPN Vertical Distribution Boards double door IP43 protection with MCCB four pole 16 KA, 63 Amp with fixed thermal and magnetic settings as incomer with suitable rated busbar, neutral link, and MCB SP 40 Amp - 5 Nos as outgoings complete all as specified and directed.

Supply and Fixing in replacement energy saver Bulkhead designed 9/10 W LED 6000 K for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer

M&L for sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including heavy duty concealed rigid PVC conduit (ISI marked) not less than 20mm dia. totally concealed in walls with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire and connecting to common earth terminals and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed. NOTES: (a) Proper colour coding shall adopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 6 sq.mm cable and one run of PVC conduit shall be measured as one unit. (c) Rate includes cutting chases for conduits and making good to walls etc.

Supply and fix in replacement MCB SP, AC 240 V,6 to 32 Amps 10 KA capacity ,'C' series making connection with suitable size of copper lugs etc complete all as specified and directed by engineer-in-charge.

Supply and fix in replacement MCB SPN, AC 240 V,40 to 63 Amps 10 KA capacity ,'C' series making connection with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-charge.

Supply and fix in replacement sheet metal enclosure (Factory made) double door shutter type for distribution board (when MCBs are to be used) single pole and neutral 240 volts 8 way protection class IP-42,suitabl for fixing MCBs, Isolators etc,confirming as per IEC 61439-3,suitable for flush mounting and surface mounting,with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

Supply and fix in replacement security light of building with single piece New generation energy saving and environmental friendly long life LED 35W made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of Light grade GI Pipe 25 mm dia 1.5 mtr long fixed to wall/ pole with two clams made out of MS FI 40mm x 5mm and connect to nearest electric supply by three core 1.5 sqmm copper cable all as directed and as specified.

M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia, by means of nut bolts, check nuts and washer of the GI. Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion. Note : Rate of GI earthwire and GI protection pipe upto 7.5mtr length shall be deemed to be included in this item.

Supply and fix 250mm sweep Exhaust fan made of sturdy engineering plastic with louvers shutter 230 volt 50 HZ 1200 RPM copper winding and fixing the exaust fan in the space provided in ventilator shutters of toilets & bathrooms including three core copper conductor flexible cord of 0.5 sqmm cross sectional area of required length from ceiling rose to exhaust fan all as specified and as directed.

Supply & Fix Panel/Meter Box of size 80 cm x 60 cm x 30cm made out of 18 SWG MS Sheet having one side openeble hinged door shuter with transperent glass for meter reading with locking arrangement mounted on wall complete with two coats of approved enamel paints over one coat of primer including making of cable connection with necessary glands, lugs/ thimbles all as specified.

S&F glint USB charger, 2 module, 3A all as specified and directed. Make: Indo Asian Cat Part No. 810651 or equivalent in Havells / Anchor / Legrand.

M/s AG PATHAN (BID ID -3256205)

OM SAI ASSOCIATES (BID ID -3257100)

M/S MAHESHWARI ENTERPRISES (BID ID -3256234)

M/s IBEX Engineers and Contractors (BID ID -3256424)

NATHKRUPA CONSTRUCTION (BID ID -3256720)

M/S. Z.K.ENTERPRISES, AHMEDNAGAR (BID ID -3256216)

DESIRES ENGINEERS &CONTRACTORS (BID ID -3256721)