PROVISION OF CERTAIN REVENUE AND MINOR WORK UNDER GE (P) LOHITPUR

Amount

Surface excavation in any type of soil n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide n exc 1.5 m deep in soft/ loose soil for foundation etc or for shaft, wells, manholes, cable etc n exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft and disintegradit soil complete all as specified and directed.

Returning ,filling in including spreading ,levelling watering and well ramming of soft/loose soil in layers n exc 25 cm thick complete all as specified and directed.

Removing excavated soil n exceeding 50 m distance and depositing where directed at alevel n exc 1.5 metre above the starting point .complete all as specified and directed.

Material and labour for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for treating the bottom and sides EC-20 confrming to IS 8944 - 2005 of excavation at the rate of 5 litres of emulsion per sqm of surface area all as specified complete all as specified and directed.

M&L for treating the back fill with EC-20 confrming to IS 8944 - 2005 in contact with foundation at the rate of 7.5 litres of emulsion per sqm of vertical surface area complete all as specified and directed.

M&L for treating the top surface with EC-20 confrming to IS 8944 - 2005 of filled earth at the rate of 5 litres of emulsion per sqm of surface area all as specified completed all as specified and directed.

M&L for treating the soil alongwith external perimeter with EC-20 confrming to IS 8944 - 2005 of the building at the rate of 2.5 litres of emulsion per Rm of surface area all as specified complete all as specified and directed.

M&L for Treating the soil under plinth protection/ under floor with EC-20 confrming to IS 8944 - 2005 at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Treating the soil along with external perimeter of building with EC-20 confrming to IS 8944 - 2005 at the rate of 2.25 litre of emulsion per metre of the perimeter wallcomplete all as specified and directed.

M& L Cement Concrete, 1:4:8, Type D-2 (using 40 mm graded crusehed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate) foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

Material and labour Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate)as in columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate)as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and labour Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate) as in chajjas complete all as specified and directed.

Material and labour Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Cement concrete 50 mm thick type B-1, 1:2:4 (20mm graded aggregate) complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in floor/plinth protection , finish even & smooth without using extra cement all as specified and directed.

Material and labour for use and waste for Formwork to sides of concrete foundations, footings, bases of col umns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; rough finished surfaces of conrete flat

Material and labour for use and waste for Formwork to sides of squar ,rectangular or polygonal pillars, posts, struts, piers, columns and stanchions rough finished surfaces of conrete flat complete all as specified and directed.

Material and labour for use and waste for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc rough finished also splays between floors and beams, etc complete all as specified and directed.

Material and labour for use and waste for Formwork to chullah hoods, chajjas, troughs and similar items in cluding edges, rough finished surfaces of conrete flat complete all as specified and directed.

Material and labour for use and waste for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide ,rough finished surfaces of conrete flat

Material and labour for use and waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Material and labour for Mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Material and labour for Mild steel TMT bars 6 to 8mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M &L Brickwork with subclass 'B' old size bricks, straright or corved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

Material and Labour for rendering 10 mm thick in cement mortar 1:6 on verticle surface of brick work or concrete surface finished even smooth without using extra cement complete all as specified and as directed.

Material and Labour for rendering 10 mm thick in cement mortar 1:4 on verticle surface of brick work or concrete surface finished even smooth without using extra cement complete all as specified and as directed.

Material and Labour for rendering 15 mm thick in two coat (10 mm +5 mm) in cement mortar 1:4 in other than fair faces of brick work with using water proofing compound in external surafce, finished even and smooth without using extra cement complete all as specified and as directed. Notes: Waterproofing compound shall be measured and paid separately under relevant items of this schedule.

Material and Labour for plaster, 5 mm thick in cement mortar 1:3 on ceiling surface of brick work or concrete surface finished even smooth without using extra cement complete all as specified and as directed.

Supply only Integral Water Proofing Compound complete all as specified and directed.

M&L for preparing the new plastered surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

M&L for preparing the new plastered surfaces and applying two coats of Oil bound distemper over a coat Primer on walls all as specified and direcrted.

M&L for preparing the new plastered surfaces and applying two coats of colour wash over a coat of wash white on walls all as specified and direcrted.

M&L for surface prepration and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)over 1mm putty complete all as specified and directed.

M&L for preparing the new plastered surfaces of ceiling and applying two coats of Oil bound distemper over a coat Primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

S& F mild steel Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.Fe-290(Gde E165) complete all as specified and directed.

S & F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming Fe-290 (Gde E-135) complete all as specified and directed.

S& F mild steel Roof trusses (framed), trussed,purlins, crane gantries, rails andfastenings and heavy bracket, Box section post, framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

M&L for Mild steel screw bolts 10-15mm long & dia of neck 11-15 mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.

M&L mild steel confirming Fe-290 as in small articles as holdfasts etc complete all as specified and directed.

Supply and Fixed PVC (SWR) 110 mm dia pipe single socketed, type-B, confrming to IS 13592: 1992 in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply and fixed PVC (SWR) bends/Tee 110 mm dia any radius complete all as specified and directed.

Supply and fixed PVC (SWR) cowl 110 mm dia any radius complete all as specified and directed.

Supply and Fixed PVC (SWR) 75 mm dia pipe single socketed, type-B, confrming to IS 13592: 1992 in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply and fixed PVC (SWR) bends/Tee 75 mm dia any radius complete all as specified and directed.

Supply and fixed PVC (SWR) vent cowl 75mm complete all as specified and directed.

M &L Concrete bed to drain pipes in cement concrete 1:3:6, Type C-2 (using40 mm graded crushed stone agreegate) for 110 mm dia pipe including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M &L Concrete bed to drain pipes in cement concrete 1:3:6, Type C-2 (using40 mm graded crushed stone agreegate) for 75 mm dia pipe including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L hardcore of brokenstones of gauge n exc 63mm, deposited spreaded , levelled in layers n exc 15 cm thick watered and rammed to true surface all as specified.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed complete all as specified and directed.

M & L for 60 mm thick , M-35 grade, Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 including 50 mm thick sand layer complete all as specified and as directed.

M&L 100 mm thick Cement concrete type, 1:4:8, type D-2, (40mm graded aggregate) as in as in sub base complete all as specified and directed.

Material and labour for 25mm thick PCC (1:2:4) type B-0 (Using 12.5 mm crushed agreegate) as in bedding layer, finished even and fair to receive tiles complete all as specified.

M&L 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in as in sub base complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles as in Vertical suraface of wall 10 cm ht . set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material and labour for non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed ben in cement mortar 1:6 complete all as specified and directed.

Material and labour for Dark Shade, double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed

Supplied and fixed Glazed vitrified ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick backing layer in cement mortar 1:4 complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of anycolour having tensilestrength of 550 Mpa as inroof covering/cladding to wall, fixed with selftapping screws as specified complete all as specified and directed.

M &L for Non asbestos fibrecement buildingboards 4 mm thick fixed orlaid/ inserted to timber/GI/Aluminium frameworkwith screwcomplete all as specified and directed.

M&L for Gl frame work for seamless ceiling comprising of G l perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to entre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners wit mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips cross the intermediate channel at 457 mm centre to centre complete all as specified and directed.

M&L water proofing treatment to RCC roof slab including parapet comprising of following course of treatment/specified from bottom to top (i) preparing the surface to remove cement laitance and to achieve an open textured surface and Loose friable material and weak concrete must be completely removed. (ii) 15 mm thick plaster in cement mortar 1:4 using water proofing compound. (iii) The surface shall be painted with one coat of cold applied bituminous primer conforming to IS:3384, @ 0.40 Kg per Sqm. (iv) APP based polymeric membrane not less than 3 mm thick weighing not less than 3.5 Kg/sqm, reinforced with polyst non-waver fabric (weighing not less than 150gm/sqm) aed. It shall be laid by torch application (two coat of heat resisting paint over APP membrane all as specified and directed by Engineer-in-charge. side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and joints shall also be sealed by torch application. for parapets, membrane shall be taken to a height of min 60 cm and then inserted inside the parapet in a groove. the same shall be finished by a membrane flashing. (iii) Coved fillet in PCC (1:2:4) tpe B0 of radius 75 mm shall be provided at the junctions of roof and parapet wall / mumty / chimney/ other vertical surfaces complete all as specified and directed.

S &F Tubes, 'medium grade' galvanised 15 mm, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S &F Tubes, 'medium grade' galvanised 20 mm, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

S & F Waste coupling of PTMT 40MM (half or full threaded) .(Minimum weight 32mm45gms/40mm-60 gms) Complete all as specified and directed.complete all as specified and directed.

Rotational moulded polyethylene water storage tanks capacit 500 ltr (cylindrical verticalwith closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Supply and fix vitreous china, wash hand basin, white, flat back, size 550 x 400 mm including brackets, brass chromium plated waste fitting.complete all as specified and directed.

Supply and fix , 10 litres capacity, Vitreous China valveless, syphonic action type, flushing cistern, low level,white, with inlet, ball valve,float and handle including brackets complete all as specified and directed.

Supply only Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & f for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

Supply and fix Vitreous China wash down water closet pan (pedestal pattern), white including sheet cover (excluding fixing bolts, flushing cistern and flush pipe,) complete all as specified and directed.

S & F for Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)complete all as specified and directed.

S & F Toilet paper holder of brass, chromium plated or stainless steel fixed to walls with chromium plated (CP) brass screws completed as specified and directed.

Supply and fix Looking Mirror of size 450x600 complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats.(Minimum weight 105gms) complete all as specified and directed.

S&F Bib tap standard of PTMT 15mm any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm125gms) complete all as specified and directed.

Supply & fixed Stop valve of PTMT 15 mm (Conclead type) any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms/ 20mm92gms)all as specified and directed.

S & F Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight15mm-110gms complete all as specified and directed.

S & F Stop valve of PTMT 20 mm any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm92gms) complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F pressed steel frames for doors of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, Size of fame

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type , both face is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

S & F 35 mm Glazed and skeleton shutters,(Second Class Hard wood) open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed

S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing Pressed Steel Windows glazed & gauged (combined type) including grills, glazing & wire mesh(SS) /Ventilator using box type hinges, MS Spring Latch, MS tower Bolt and telescopic stay complete complete all as specified and directed.

S&F Aluminium anodised,barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed.

S&F Aluminium alloy, anodised,sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Butt hinges of 125 mm size, Medium weight, cold rolled mild steel and fixed, complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type., anodised Size of handle in mm 125 complete all as specified and directed.

Supply and fixing Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and directed.

M&L 4 mm thick Figured glass, pinhead type in squares n exc 0.5 sq.m each panecomplete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with M.S tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2,4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core supplying & fixing in frame as per specification and drawing and directed complete all as specified and directed.

S&F Butt hinges of 100 mm size, Medium weight, cold rolled mildsteel and fixed, complete all as specified and directed.

M &L for Polythene film, black, 50micron laid in floors complete all as specified and directed.

Material and Labour for LLDPE septic tank for 5 user capacity, designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation vent shaft connection etc.complete all as specified and directed.

M &L Brickwork with subclass 'B' old size bricks, in half brick thick honey comb work straright or corved on plan exc 6m mean radius built in Cement mortar 1:4 complete all as specified and directed.

Material and labour for Loose filling with brocken brick aggregates of gauge 80 to 150 mm in . soakage pits, soakage wells complete all as specified and as directed.

M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sq mm FRLHS in and including concealed PVC conduit 20/25 mm dia medium duty ISI marked with all necessary fittings for mounting of modular switches/sockets including 1.5 sq mm FRLHS PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light/ceiling fan/exhaust fan controlled by one switch complete including cutting, chasing the surface and then making good the same in CM 1:3 complete all as specified and directed by Engr- in-charge.

All as per item No. 108 above but one socket outlet 3 or 5 pin, 6 Amps on independent board complete all as specified and directed.

All as per item No. 108 above but 3 pin 5 amps socket out let point with the same board with other switches with cables of 1.5 Sqmm size complete all as specified and directed.

All as per item No. 108 here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLHS PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed.

S/F sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls complete for 2 modules complete all as specified and directed.

-do- all as per item No 111 above but for 3 modules complete all as specified and directed.

-do- all as per item No 111 above but for 4 modules complete all as specified and directed.

-do- all as per item No 111 above but for 6 modules complete all as specified and directed.

-do- all as per item No 111 above but for 8 modules complete all as specified and directed.

S/F ceiling rose, 3 ph plastic round PVC/ polycarbonate isolated body for mounting ceiling fan/exhaust fan/light fittings complete all as specified and directed.

S/F modular cover plate with frame for fixing of modular switches/sockets for 2 modules complete all as specified and directed.

-do- all as per item No. 117 above but for 3 modules complete all as specified and directed.

-do- all as per item No. 117 above but for 4 modules complete all as specified and directed.

-do- all as per item No. 117 above but for 6 modules complete all as specified and directed.

-do- all as per item No. 117 above but for 8 modules complete all as specified and directed.

S/F switch piano modular flush type 5/6 Amps 230V AC complete one way complete all as specified and directed.

S&F modular socket 6A out let 2/3 pin 5 Amps flush type complete all as specified and directed.

S&F modular switch socket outlet multipurpose 3 pin 15 Amps and one pin 5 Amps controlled by one switch complete all as specified and directed.

S & F surface and wall mounted LED batten 4feets with 1x20W indoor decorative luminaries with and including electronic driver and 1x20W LED lamp,pre wired including necessary electric connection copper flexible PVC cable of 0.5 sqmm 3 core not more than 1m in length from ceiling rose to light fittings complete all as specified and directed.

S & F surface and wall mounted LED batten 2 feets with 1x10W indoor decorative luminaries with and including electronic driver and 1x10W LED lamp,pre wired including necessary electric connection copper flexible PVC cable of 0.5 sqmm 3 core not more than 1m in length from ceiling rose to light fittings complete all as specified and directed.

Supply and Fixing of Flameproof cum Waterproof LED Bulk Head light fitting of 30W, IP66 protection of Cast Aluminum alloy material and Heat and Impact resistance toughen 'A' clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size

S&F sheet metal enclosure for DB's when MCBs to be used 4 way single pole and neutral double door with 200 amps rated bus bar complete including connection all as specified.

S&F MCB 6 to 32 amps single pole amp rating 240V, 10KA breaking capacity 'C' Curve complete all as specified.

S&F MCB DP 40 amps 240 volts 10KA breaking capacity 'C' Curve complete all as specified.

M & L for 40mm bore GI tubes light grade for cable protection inside in walls making good surface with all fixing accessoires (clamps, nut, bolt and washer etc) complete all as specified and directed. Make Jindal/Tata/Nezone

Supply & Fixing XLPE insulated PVC sheathed armoured LT 1100 volt grade aluminimum conductor cable of size 10 sqmm 2 core conforming to IS 7098 Part - I complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth all as specified and directed by Engineer-in-charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers.

Supply and fix Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm bore and fixed

Supply and fix Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 15mm bore and fixed

Supply and Fix DOL Starter FOR 0.5 HP Motor.Make L&T cat no SS94351

Supply and fixing pumpset,cetrifugal,electric driven 0.5 HP AC single phase 230V inclusive of electrical connections and PCC foundation with MS frame and GI sheet cover.

Supply and fixed double wall corrugated pipe 50 mm dia, SN 8 laid in trenches for cable protection complete all as specified and as directed.

M & L for 20 mm bore GI tubes light grade for cable protection inside in walls making good surface with all fixing accessoires (clamps, nut, bolt and washer etc) complete all as specified and directed. Make Jindal/Tata/Nezone

S&F plug and socket in sheet metal enclosures with two pin and earth plug and socket complete with and including MCB SP 20 Amps 240 volts heavy duty including taking town of old UNSV one all as specified and as directed by Engr-in-charge. Make- Legrand or in Hagger, L&T.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F sub main wiring two run of single core PVC insulated unsheathed stranded copper conductor of size 4 sqmm & one run of PVC insulated unsheathed stranded copper conductor of size 4 sqmm as earth lead drawing into rigid non metalic PVC conduit of size 20 mm dia including taking down old unsv. Note: Three run of 4 sqmm cable will be measured as single length.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories 230V, 1200 sweep min air delivery 210 CFM with service value 6.00 BEE. Five Star rated with brushless direct current motor (BLDC).

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0 mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including GI earth lead wire of size 4 mm dia as earthing lead by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion complete all as per specified and as directed.

S&F modular SSC outlet each 3 pin 5 Amps, 230V flush type complete all as specified and as directed.

S&F sheet metal enclosure for DB's where MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete including connection all as specified.

M&L for XLPE insulated PVC sheathed armoured LT 1100V aluminium conductor cable of size 2 core 25 Sqmm conforming to IS 7098 Part-I complete all as specified and as directed.

MAHABAHU ENTERPRISE (BID ID -3473707)