Construction of Auditorium with Open Air-Theater in the premises of College of Agriculture at Bawal (Rewari) (including PH and EI works)

Amount

Civil work 1 to 131:- EARTH WORK AND ROCK CUTTING Surface Dressing Of The Ground Including Removing Vegetation And In-Equalities Not Exceeding 15 Cm Deep And Disposal Of Rubbish, Lead Up To 50 M And Lift Up To 1.5 M. All Kinds Of Soil (HSR 4.4.1)

Earth Work In Excavation By Mechanical Means (Hydraulic Excavator) / Manual Means In Foundation Trenches Or Drains (Not Exceeding 1.5 M In Width Or 10 Square meter On Plan), Including Dressing Of Sides And Ramming Of Bottoms, Lift Up To 1.5 M, Including Getting Out The Excavated Soil And Disposal Of Surplus Excavated Soil As Directed, Within A Lead Of 50 M. 50M Lead (HSR 4.14.1)

Extra For Every Additional Lift Of 1.5 M Or Part Thereof In Excavation / Banking Excavated Or Stacked Materials. All Kinds Of Soil (HSR 4.31.1)

Filling Available Excavated Earth (Excluding Rock) In Trenches, Cubic meter Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20Cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering, Lead Up To 50 M And Lift Up To 1.5 M. (HSR 4.32)

Providing And Injecting Chemical Emulsion For Pre Constructional Anti Termite Treatment And Creating A Chemical Barrier Under And Around The Column Pits, Wall Trenches, Basement Excavation, Top Surface Of Plinth Filing Junction Of Wall And Floor, Along With The External Perimetre Of Building, Expansion Joints Surrounding Of Pipes And Conduit Etc, Complete (Plinth Area Of The Building At Ground Floor Only Shall Be Measured) Using Chlorpyriphos/ Lindane Emulsifiable Concentrate Of 20%. (HSR 4.39)

Carriage Of Earth By Mechanical Transport Including Loading, Unloading For A Lead Upto 10 Km. (HSR 3.1.2)

Concrete And Rcc Work Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Below Plinth Level And Up To Floor Iv Level: 1:2:4 (1 Cement : 2 Coarse Sand (Zone-Ill) : 4 Graded Stone Aggregate 20 Mm Nominal Size) (HSR 6.1.2)

1 :4: 8 ( 1 Cement : 4 Coarse Sand (Zone-Ill) : 8 Graded Cubic meter Stone Aggregate 40 Mm Nominal Size) (HSR 6.1.6)

Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls (Any Thickness) Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Four Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 :2:4 (1 Cement : 2 Coarse Sand (Zone-Ill) : 4 Graded Stone Aggregate 20 Mm Nominal Size). (HSR 6.2.2)

Extra For Providing And Mixing Water Proofing Material In Cement 50 Kg Concrete Work In Doses By Weight Of Cement As Per Manufacture R'S Specification. (HSR 6.5)

Providing And Laying Damp-Proof Course With Cement Concrete 1 :2:4 (1 Cement : 2 Coarse Sand (Zone-Ill): 4 Graded Stone Aggregate 12.5Mm Nominal Size) 50 Mm Thick (HSR 6.8.1)

Making Plinth Protection 50Mm Thick Of Cement Concrete 1 :3:6 (1 Square meter Cement : 3 Coarse Sand : 6 Graded Stone Aggregate 20 Mm Nominal Size) Over 75Mm Thick Bed Of Dry Brick Ballast 40 Mm Nominal Size, Well Rammed And Consolidated And Grouted With Fine Sand, Including Necessary Excavation, Levelling & Dressing & Finishing The Top Smooth. (HSR 6.13)

Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M-25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is: 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-In-Charge. All Works Up To Plinth Level (HSR 6.25.1)

All Works Above Plinth & Up To Floor Iv Level. (HSR 6.25.2)

Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form Work For : Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete. (HSR 6.30.1)

Walls (Any Thickness) Including Attached Pilasters,Buttresses, Plinth And String Courses Etc. (HSR 6.30.2)

Suspended Floors, Roofs, Landings, Balconies And Access Platform. (HSR 6.30.3)

Shelves (Cast In Situ) (HSR 6.30.4)

Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers (HSR 6.30.5)

Columns, Pillars, Piers, Abutments, Posts And Struts (HSR 6.30.6)

Stairs, (Excluding Landings) Except Spiral-Staircases (HSR 6.30.7)

Small Lintels Not Exceeding 1.5 M Clear Span, Square meter Moulding As In Cornices, Window Sills, String Courses, Bands, Copings, Bed Plates, Anchor Blocks And The Like. (HSR 6.30.15)

Edges Of Slabs And Breaks In Floors And Walls Under 20 Cm Wide (HSR 6.30.16.1)

Weather Shade, Chhajjas, Corbels Etc., Including Edges. (HSR 6.30.19)

Extra For Additional Height In Centering, Shuttering Where Ever Required With Adequate Bracing, Propping Etc., Including Cost Of De-Shuttering And Decentring At All Levels, Over A Height Of 3.5 M, For Every Additional Height Of 1 Metre Or Part Thereof (Plan Area To Be Measured). Suspended Floors, Roofs, Landing, Beams And Square meter Balconies (Plan Area To Be Measured). (HSR 6.32.1)

Steel Reinforcement For R.C.C. Work, Where Not Included In The Complete Rate Of Rcc, Including Straightening, Cutting, Bending, Placing In Position, Binding, Wastage, Overlaps, Welded Joints, Spacer Bars, Chairs, Stays, Hangers And Annealed Steel Wire Etc. Complete In All Respect Below Plinth Level Note:- Reinforcement Shall Be Measured In Length Including Hooks, If Any, Separately For Different Diameters As Actually Used In Work , Excluding Overlaps. Wastage, Overlaps, Couplings, Welded Joints, Spacer Bars, Chairs, Stays, Hangers And Annealed Steel Wire Or Other Methods Of Binding & Placing Shall Not Be Measured And Cost Of These Items Shall Be Deemed To Be Included In The Rates For Reinforcement. Thermo-Mechanically Treated Bars Of Grade Fe-500D Kg Or More. (HSR 6.33.6)

Steel Reinforcement For R.C.C. Work, Where Not Included In The Complete Rate Of Rcc, Including Straightening, Cutting, Bending, Placing In Position, Binding, Wastage, Overlaps, Welded Joints, Spacer Bars, Chairs, Stays, Hangers And Annealed Steel Wire Etc. Complete In All Respect Above Plinth Level. Note:- Reinforcement Shall Be Measured In Length Including Hooks, If Any, Separately For Different Diameters As Actually Used In Work , Excluding Overlaps. Wastage, Over1Aps, Couplings, Welded Joints, Spacer Bars, Chairs, Stays, Hangers And Annealed Steel Wire Or Other Methods Of Binding & Placing Shall Not Be Measured And Cost Of These Items Shall Be Deemed To Be Included In The Rates For Reinforcement. Thermo-Mechanically Treated Bars Of Grade Fe-500D Kg Or More. (HSR 6.34.6)

Providing And Fixing In Position Stainless Steel Grade 304 Plate 1.0 Mm Thick As Per Design For Expansion Joints. (HSR 6.60.1) 200 Mm Wide.

Providing And Fixing Of Expansion Joint System Related With Floor Location As Per Drawings And Direction Of Engineer-In-Charge. The Joints System Will Be Of Extruded Aluminium Base Members, Self Aligning/ Self Centering Arrangement And Support Plates Etc. As Per Astm 9221-02. The System Shall Be Such That It Provides Floor To Floor /Floor To Wall Expansion Control System For Various Vertical Location In Load Application Areas That Accommodates Multi Directional Seismic Movement Without Stress To It'S Components. System Shall Consist Of Metal Profiles With A Universal Aluminium Base Member Designed To Accommodate Various Project Conditions And Finish Floor Treatments. The Cover Plate Shall Be Designed Of Width And Thickness Required To Satisfy Projects Movement And Loading Requirements And Secured To Base Members By Utilizing Manufacturer'S Pre-Engineered Self Centering Arrangement That Freely Rotates I Moves In All Directions. The Self - Centering Arrangement Shall Exhibit Circular Sphere Ends That Lock And Slide Inside The Corresponding Aluminium Extrusion Cavity To Allow Freedom Of Movement And Flexure In All Directions Including Vertical Displacement. Provision Of Moisture Barrier Membrane In The Joint System To Have Watertight Joint Is Mandatory Requirement All As Per The Manufactures Design And As Approved By Engineer -In-Charge. (Material Shall Confirm To Astm 6063). Floor Joint Of 100 Mm Gap. (HSR 6.61.1)

Providing And Fixing Of Expansion Joint System Related With Wall Joint (Internal/External) Location As Per Drawings And Direction Of Engineer-In- Charge. The Joints Shall Be Of Extruded Aluminium Base Members, Self Aligning / Centering Arrangement And Support Plates As Per Astm B221- 02. The Material Shall Be Such That It Provides An Expansion Joints System Suitable For Vertical Wall To Wall/ Wall To Comer Application, Both New And Existing Construction In Office Buildings & Complexes With No Slipping Down Tendency Amongst The Components Of The Joint System. The Joint System Shall Utilize Light Weight Aluminium Profiles Exhibiting Minimal Exposed Aluminium Surfaces Mechanically Snap Locking The Multicellular To Facilitate Movement. (Material Shall Confirm To Astm 6063). Wall Joint Of 100 Mm Gap (HSR 6.62.1)

Brick Work And Stone Masonry Brick Work With Common Burnt Clay Non-Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In: Cement Mortar 1:6 (1 Cement: 6 Coarse Sand) (HSR 7.21.2)

Brick Work With Common Burnt Clay Non-Modular Bricks Of Class Designation 7 .5 In Superstructure Above Plinth Level Up To Floor Iv Level In All Shapes And Sizes In : Brick Work With Common Burnt Clay Non-Modular Bricks Of Class Designation 7 .5 In Superstructure Above Plinth Level Up To Floor Iv Level In All Shapes And Sizes In : (HSR 7.22.2)

Half Brick Masonry With Common Burnt Clay Non-Modular Bricks Of Class Designation 7.5 In Foundations And Plinth In: Cement Mortar 1:4 (1 Cement: 4 Coarse Sand) (HSR 7.27.2)

Half Brick Masonry With Common Burnt Clay Non-Modular Bricks Of Class Designation 7 .5 In Superstructure Above Plinth Level Up To Floor Iv Level. Cement Mortar 1:4 (1 Cement: 4 Coarse Sand) (HSR 7.28.2)

Extra For Providing And Placing In Position 2 Nos. 6 Mm Dia. M.S. Square meter Bars At Every Third Course Of Half Brick Masonry (HSR 7.30)

Providing And Laying Autoclaved Aerated Cement Blocks Masonry With 100 Mm Thick Aac Blocks In Super Structure Above Plinth Level Up To Floor Iv Level In Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand ). The Rate Includes Providing And Placing In Position 2 Nos. 6 Mm Dia M.S. Bars At Every Third Course Of Masonry Work. (HSR 7.50)

Providing And Laying Autoclaved Aerated Cement Blocks Masonry With 150Mrn/230Mm/300 Mm Thick Aac Blocks In Super Structure Above Plinth Level Up To Floor Iv Level With Rcc Band At Sill Level And Lintel Level With Approved Block Laying Polymer Modified Adhesive Mortar All Complete As Per Direction Of Engineer-In?Charge. (The Payment Of Rcc Band And Reinforcement Shall Be Made For Separately). (HSR 7.51)

Cladding Work Stone Work (Machine Cut Edges) For Wall Lining Etc. (Veneer Work) Up To 10 Metre Height, Backing Filled With A Grout Of Average 12 Mm Thick Cement Mortar 1 :3 (1 Cement : 3 Coarse Sand) Including Pointing In White Cement Mortar 1 :2 (1 White Cement : 2 Stone Dust) With An Admixture Of Pigment Matching The Stone Shade : (To Be Secured To The Backing And The Sides By Means Of Cramps And Pins Which Shall Be Paid For Separately) Gang Saw Cut Stone 30Mm Thick Red Sand Stone (HSR 8.9.3.2)

Wall Lining Butch Work Up To 10M Height With Dholpur Stone 40 Mm Thick Rough Facing On The Exposed Surface With Stone Strips Of Minimum Length 300 Mm And Required Width, Including Embedding Every Tenth Layer And Bottom Most Layer In Masonry Or Concrete After Making Necessary Chases Of Size 75X75 Mm And By Providing Layer Of 75 Mm Thick Strips I/C 12 Mm Thick Bed Of Cement Mortar 1 :3 (1 Cement : 3 Coarse Sand) I/C Ruled Pointing In Cement Mortar 1 :2 (1 White Cement : 2 Stone Dust) With An Admixture Of Pigment To Match The Shade Of Stone Complete As Per Direction Of Engineer-In-Charge. (HSR 8.12)

Providing And Fixing Adjustable Stainless Steel Cramps Of Approved Quality, Required Shape And Size, Adjustable With Stainless Steel Nuts, Bolts And Washer (Total Weight Not Less Than 260 Gms), For Dry Stone Cladding Fixed On Frame Work At Suitable Location, Including Making Necessary Recesses In Stone Slab, Drilling Required Holes Etc Complete As Per Direction Of The Engineer-In-Charge. (HSR 8.3)

Providing And Fixing 18 Mm Thick Gang Saw Cut, Mirror Polished, Premoulded And Prepolished, Machine Cut For Kitchen Platfonns, Vanity Counters, Window Sills, Facias And Similar Locations Of Required Size, Approved Shade, Colour And Texture Laid Over 20 Mm Thick Base Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand), Joints Treated With White Cement, Mixed With Matching Pigment, Epoxy Touch Ups, Including Rubbing, Curing, Moulding And Polishing To Edges To Give High Gloss Finish Etc. Complete At All Levels. Granite Of Any Colour And Shade Area Of Slab Up To 0.50 Square meter (HSR 8.26.2.1)

Area Of Slab Over 0.50 Square meter (HSR 8.26.2.2)

Extra For Fixing Marble /Granite Stone, Over And Above Corresponding Basic Item, In Facia And Drops Of Width Upto 150 Mm With Epoxy Resin Based Adhesive, Including Cleaning Etc. Complete. (HSR 8.5)

Providing Edge Moulding To 18 Mm Thick Marble Stone Counters, Vanities Etc., Including Machine Polishing To Edge To Give High Gloss Finish Etc. Complete As Per Design Approved By Engineer-In-Charge. Granite Work (HSR 8.27.2)

Extra For Providing Opening Of Required Size & Shape For Wash Basin/ Kitchen Sink In Kitchen Platfonn, Vanity Counter And Similar Location In Marble/ Granite/ Stone Work, Including Necessary Holes For Pillar Taps Etc. Including Moulding, Rubbing And Polishing Of Cut Edges Etc. Complete. (HSR 8.28)

Providing And Fixing Stone Slab With Table Rubbed, Edges Rounded And Polished, Of Size 75X50 Cm Deep And 1.8 Cm Thick, Fixed In Urinal Partitions By Cutting A Chase Of Appropriate Width With Chase Cutter And Embedding The Stone In The Chase With Epoxy Grout Or With Cement Concrete 1 :2:4 (1 Cement: 2 Coarse Sand : 4 Graded Stone Aggregate 6 Mm Nominal Size) As Per Direction Of Engineer-In-Charge And Finished Smooth. Granite Stone Of Approved Shade (HSR 8.30.2)

Roofing Providing Gola 75X75 Mm In Cement Concrete 1 :2:4 (1 Cement : 2 Coarse Sand : 4 Stone Aggregate 10 Mm And Down Gauge), Including Finishing With Cement Mortar 1 :3 (1 Cement : 3 Fine Sand) As Per Standard Design : In 75X75 Mm Deep Chase (HSR 9.17.1)

Providing And Fixing False Ceiling At All Height Including Providing And Fixing Of Frame Work Made Of Special Sections, Power Pressed From M.S. Sheets And Galvanized With Zinc Coating Of 120 Gms/Square meter (Both Side Inclusive) As Per Is: 277 And Consisting Of Angle Cleats Of Size 25 Mm Wide X 1.6 Mm Thick With Flanges Of 27 Mm And 37Mm, At 1200 Mm Centre To Centre, One Flange Fixed To The Ceiling With Dash Fastener 12.5 Mm Dia X 50Mm Long With 6Mm Dia Bolts, Other Flange Of Cleat Fixed To The Angle Hangers Of 25X1 Ox0.50 Mm Of Required Length With Nuts & Bolts Of Required Size And Other End Of Angle Hanger Fixed With Intermediate G.I. Channels 45X15X0.9 Mm Running At The Spacing Of 1200 Mm Centre To Centre, To Which The Ceiling Section 0.5 Mm Thick Bottom Wedge Of 80 Mm With Tapered Flanges Of 26 Mm Each Having Lips Of 10.5 Mm, At 450 Mm Centre To Centre, Shall Be Fixed In A Direction Perpendicular To G.I. Intermediate Channel With Connecting Clips Made Out Of 2.64 Mm Dia X 230 Mm Long G.I. Wire At Every Junction, Including Fixing Perimeter Channels 0.5 Mm Thick 27 Mm High Having Flanges Of 20 Mm And 30 Mm Long, The Perimeter Of Ceiling Fixed To Wall/Partition With The Help Of Rawl Plugs At 450 Mm Centre, With 25Mm Long Dry Wall Screws @ 230 Mm Interval, Including Fixing Of Gypsum Board To Ceiling Section And Perimeter Channel With The Help Of Dry Wall Screws Of Size 3.5 X 25 Mm At 230 Mm C/C, Including Jointing And Finishing To A Flush Finish Of Tapered And Square Edges Of The Board With Recommended Jointing Compound , Jointing Tapes , Finishing With Jointing Compound In 3 Layers Covering Up To 150 Mm On Both Sides Of Joint And Two Coats Of Primer Suitable For Board, All As Per Manufacturer'S Specification And Also Including The Cost Of Making Openings For Light Fittings, Grills, Diffusers, Cut Outs Made With Frame Of Perimeter Channels Suitably Fixed, All Complete As Per Drawings, Specification And Direction Of The Engineer In Charae But Excludina The Cost Of Oaintina With 12.5 Mm Thick Tapered Edge Gypsum Plain Board Conforming To Is: 2095- (Part I) :2011 (Board With Bis Certification Marks) (HSR 9.46.1)

Providing And Fixing Tiled False Ceiling Of Specified Materials Of Size 595X595 Mm In True Horizontal Level, Suspended On Inter Locking Metal Grid Of Hot Dipped Galvanized Steel Sections ( Galvanized @ 120 Grams/ Square meter, Both Side Inclusive) Consisting Of Main "T" Runner With Suitably Spaced Joints To Get Required Length And Of Size 24X38 Mm Made From 0.30 Mm Thick (Minimum) Sheet, Spaced At 1200 Mm Centre To Centre And Cross 'T' Of Size 24X25 Mm Made Of 0.30 Mm Thick (Minimum) Sheet, 1200 Mm Long Spaced Between Main "T" At 600 Mm Centre To Centre To Form A Grid Of 1200X600 Mm And Secondary Cross "T" Of Length 600 Mm And Size 24X25 Mm Made Of 0.30 Mm Thick (Minimum) Sheet To Be Interlocked At Middle Of The 1200X600 Mm Panel To Form Grids Of 600X600 Mm And Wall Angle Of Size 24X24X0.3 Mm And Laying False Ceiling Tiles Of Approved Texture In The Grid Including, Required Cutting/Making, Opening For Services Like Diffusers, Grills, Light Fittings, Fixtures, Smoke Detectors Etc. Main 'T' Runners To Be Suspended From Ceiling Using Gi Slotted Cleats Of Size 27 X 37 X 25 X1 .6 Mm Fixed To Ceiling With 12.5 Mm Dia And 50 Mm Long Dash Fasteners, 4 Mm Gi Adjustable Rods With Galvanised Butterfly Level Clips Of Size 85 X 30 X 0.8 Mm Spaced At 1200 Mm Centre To Centre Along Main T, Bottom Exposed Width Of 24 Mm Of All T-Sections Shall Be Pre-Painted With Polyester Paint, All Complete For All Heights As Per Specifications, Drawings And As Directed By Engineer-In-Charge. Gi Metal Ceiling Lay In Plain Tegular Edge Global White Colour Tiles Of Size 595X595 Mm, And 0.5 Mm Thick With 8 Mm Drop; Made Of G I Sheet Having Galvanizing Of 100 Gms/Square meter (Both Sides Inclusive) And Electro Statically Polyester Powder Coated Of Thickness 60 Microns (Minimum), Including Factory Painted After Bending. (HSR 9.47.1)

Flooring And Dados Providing And Laying Of Base Course Of Floors Consisting Of 100 Mm Thick Square meter Cement 1 :8: 16 And 100 Mm Sand Or Stone Filling. (HSR 10.1)

Providing And Laying Cement Concrete Flooring 1 :2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) Finished With A Floating Coat Of Neat Cement, Including Cement Slurry, But Excluding The Cost Of Nosing Of Steps Etc. Complete. 40 Mm Thick With 20 Mm Nominal Size Stone Aggregate. (HSR 10.10.1)

Providing And Fixing Of Kota Stone Slab Flooring Over 20 Mm (Average) Thick Base Laid Over And Jointed With Grey Cement Slurry Mixed With Pigment To Match The Shade Of The Slab, Including Rubbing And Polishing Complete With Base Of Cement Mortar 1 : 4 ( 1 Cement : 4 Coarse Sand) : 25 Mm Thick (HSR 10.37.1)

Providing And Fixing Of Kota Stone Slabs 20 Mm Thick In Risers Of Steps, Skirting, Dado And Pillars Laid On 12 Mm (Average) Thick Cement Mortar 1:3 (1 Cement: 3 Coarse Sand) And Jointed With Grey Cement Slurry Mixed With Pigment To Match The Shade Of The Slabs, Including Rubbing And Polishing Complete. (HSR 10.38)

Providing And Laying Flamed Finish Granite Stone Flooring In Required Design And Patterns, In Linear As Well As Curvilinear Portions Of The Building All Complete As Per The Architectural Drawings With 18 Mm Thick Stone Slab Over 20 Mm (Average) Thick Base Of Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand) Laid And Jointed With Cement Slurry And Pointing With White Cement Slurry Admixed With Pigment Of Matching Shade Including Rubbing, Curing And Polishing Etc. All Complete As Specified And As Directed By The Engineer-In Charge: Flamed Finish Granite Stone Slab Jet Black, Cherry Red, Elite Brown, Cat Eye Or Equivalent. (HSR 10.49.1)

Providing And Laying Polished Granite Stone Flooring In Required Design And Patterns, In Linear As Well As Curvilinear Portions Of The Building All Complete As Per The Architectural Drawings With 18 Mm Thick Stone Slab Over 20 Mm (Average) Thick Base Of Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand) Laid And Jointed With Cement Slurry And Pointing With White Cement Slurry Admixed With Pigment Of Matching Shade Including Rubbing , Curing And Polishing Etc. All Complete As Specified And As Directed By The Engineer-In-Charge. Polished Granite Stone Slab Jet Black, Cherry Red, Elite Brown, Cat Eye Or Equivalent. (HSR 10.50.1)

Providing And Fixing Granite Stone In All Shades 15Mm To 18 Mm Thick In Skirting /Dado, Risers Of Steps, Pillars And Wall Facing, Laid In Any Pattern As Specified Over Base Of 12Mm Thick Cement Coarse Sand Mortar 1 :3 And Jointed With White Cement Slurry Mixed With Pigment To Match The Shade Of Granite Including Labour For Fixing Cramps Pins And Dowels Etc. (HSR 10.51)

Providing And Fixing 1St Quality Ceramic Glazed Wall Tiles Conforming To Is :15622 (Thickness To Be Specified By The Manufacturer ) Of Approved Make In All Colours, Shades Except Burgundy, Bottle Green, Black Of Any Size As Approved By Engineer-In-Charge In Skirting, Risers Of Steps And Dados Over 12 Mm Thick Bed Of Cement Mortar 1 :3 (1 Cement: 3 Coarse Sand) And Jointing With Grey Cement Slurry @ 3.3Kg Per Square meter Including Pointing In White Cement Mixed With Pigment Of Matching Shade Complete. (HSR 10.58)

Providing And Laying Rectified Glazed Ceramic Floor Tiles Of Size 300X300 Mm Or More (Thickness To Be Specified By The Manufacturer), Of 1St Quality Conforming To Is : 15622, Of Approved Make, In All Colours, Shades, Except White, Ivory, Grey, Fume Red Brown, Laid On 20 Mm Thick Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/ Square meter Including Pointing The Joints With White Cement And Matching Pigments Etc., Complete. (HSR 10.61)

Providing And Laying Vitrified Floor Tiles In Different Sizes (Thickness To Be Specified By The Manufacturer) With Water Absorption Less Than 0.08% And Conforming To Is: 15622, Of Approved Make, In All Colours And Shades, Laid On 20Mm Thick Cement Mortar 1 :4 (1 Cement : 4 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/ Square meter Including Grouting The Joints With White Cement And Matching Pigments Etc., Complete. Size Of Tile 600X600 Mm (HSR 10.63.2)

Providing And Laying Vitrified Tiles In Different Sizes (Thickness To Be Specified By Manufacturer), With Water Absorption Less Than 0.08 % And Conforming To I.S. 15622, Of Approved Make, In All Colours & Shade, In Skirting, Riser Of Steps, Over 12 Mm Thick Bed Of Cement Mortar 1 :3 (1 Cement: 3 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/ Square meter Including Grouting The Joint With White Cement & Matching Pigments Etc. Complete. Size Of Tile 600X600 Mm (HSR 10.67.2)

Finishing Works 6 Mm Cement Plaster Of Mix 1 :3 (1 Cement : 3 Fine Sand) (HSR 11.1.1)

12 Mm Cement Plaster Of Mix : 1 :4 (1 Cement: 4 Coarse Sand) (HSR 11.8.1)

15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix: 1 :4 (1 Cement: 4 Coarse Sand) (HSR 11.9.1)

Add For Plaster Drip Course/ Groove In Plastered Surface Or Moulding To R.C.C Projections. (HSR 11.54)

Providing And Applying Plaster Of Paris Putty Of 2 Mm Thickness Over Plastered Surface To Prepare The Surface Even And Smooth Complete. (HSR 11.59)

White Washing With Lime To Give An Even Shade New Work (Three Or More Coats) (HSR 11.61.1)

Distempering With Oil Bound Washable Distemper Of Approved Brand And Manufacture To Give An Even Shade: New Work (Two Or More Coats) Over And Including Water Thinnable Priming Coat With Cement Primer (HSR 11.64.1)

Wall Painting On A Cement Plaster Surface With Acrylic Emulsion Paint Of Approved Brand And Manufacture To Give An Even Shade : Two Or More Coats On New Work. (HSR 11.71.1)

Finishing Walls With Textured Exterior Paint Of Required Shade : New Work (Two Or More Coats Applied @ 3.28 Ltr/10 Square meter) Over And Including Priming Coat Of Exterior Primer Applied @ 2.20Kg/10 Square meter. (HSR 11.94.1)

Neat Cement Punning. (HSR 11.3)

Wood Work Providing And Fixing Isi Marked Flush Door Shutters Conforming To Is : 2202 (Part I) Non-Decorative Type, Core Of Block Board Construction With Frame Of 1St Class Hard Wood And Well Matched Commercial 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters: 35 Mm Thick Including Isi Marked Stainless Steel Butt Hinges With Necessary Screw. (HSR 12.37.1)

Extra For Providing Lipping With 2Nd Class Teak Wood Battens 25 Mm Minimum Depth On All Edges Of Flush Door Shutters (Over All Area Of Door Shutter To Be Measured). (HSR 12.39)

Extra For Cutting Rebate In Flush Door Shutters (Total Area Of The Shutter To Be Measured). (HSR 12.42)

Providing And Fixing Bright Finished Brass 100 Mm Mortice Latch And Lock With 6 Levers And A Pair Of Lever Handles Of Approved Quality With Necessary Screws Etc. Complete. (HSR 12.81)

Providing And Fixing Aluminium Hanging Floor Door Stopper, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 1 O As Per Is : 1868) Transparent Or Dyed To Required Colour And Shade, With Necessary Screws Etc. Complete Twin Rubber Stopper (HSR 12.103.2)

Providing And Fixing Factory Made Upvc Door Frame Made Of Upvc Extruded Sections Having An Overall Dimension As Below (Tolerance ±1 Mm), With Wall Thickness 2.0 Mm (± 0.2 Mm), Corners Of The Door Frame To Be Jointed With Galvanized Brackets And Stainless Steel Screws, Joints Mitred And Plastic Welded. The Hinge Side Vertical Of The Frames Reinforced By Galvanized M.S. Tube Of Size 19 X 19 Mm And 1 Mm (± 0.1 Mm) Wall Thickness And 3 Nos. Stainless Steel Hinges Fixed To The Frame Complete As Per Manufacturer'S Specification And Direction Of Engineer- In-Charge Extruded Section Profile Size 48X40 Mm (HSR 12.117.1)

Providing And Fixing Factory Made Upvc White Colour Fixed Glazed Windows/Ventilators Comprising Of Upvc Multi-Chambered Frame And Mullion (Where Ever Required) Extruded Profiles Duly Reinforced With 1.60 :T 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), , Upvc Extruded Glazing Beads Of Appropriate Dimension, Epdm Gasket, G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall, Plastic Packers, Plastic Caps And Necessary Stainless Steel Screws Etc. Profile Of Frame Shall Be Mitred Cut And Fusion Welded At All Comers, Mullion (If Required) Shall Be Also Fusion Welded Including Drilling Of Holes For Fixing Hardware'S And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealant Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single / Double Glass Panes And Silicon Sealant Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame, Sash And Mullion Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Fixed Window/ Ventilator Made Of (Small Series) Frame 47 X 50 Mm & Mullion 47 X 68 Mm Both Having Wall Thickness Of 1.9 :T 0.2 Mm And Single Glazing Bead Of Appropriate Dimension. (Area Up To 0.75 Square meter) (HSR 12.132.1)

Providing And Fixing Factory Made Upvc White Colour Sliding Glazed Window Up To 1.50 M In Height Dimension Comprising Of Upvc Multi-Chambered Frame With In-Built Roller Track And Sash Extruded Profiles Duly Reinforced With 1.60 ± 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), Appropriate Dimension Of Upvc Extruded Glazing Beads And Upvc Extruded Interlocks, Epdm Gasket, Wool Pile, Zinc Alloy (White Powder Coated) Touch Locks With Hook, Zinc Alloy Body With Single Nylon Rollers (Weight Bearing Capacity To Be 40 Kg), G.I Fasteners 100 X B Mm Size For Fixing Frame To Finished Wall And Necessary Stainless Steel Screws Etc. Profile Of Frame & Sash Shall Be Mitred Cut And Fusion Welded At All Corners, Including Drilling Of Holes For Fixing Hardware'S And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealant Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single / Double Glass Panes, Wire Mesh And Silicon Sealant Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame And Sash Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Two Track Two Panels Sliding Window Made Of (Small Series) Frame 52 X 44 Mm &Sash 32 X 60 Mm Both Having Wall Thickness Of 1.9 ± 0.2 Mm And Single Glazing Bead Of Appropriate Dimension. (Area Of Window Up To 1.75 Square meter) (HSR 12.134.1)

Three Track Three Panels Sliding Window With Fly Proof S.S Wire Mesh (Two Nos. Glazed & One No. Wire Mesh Panels) Made Of (Big Series) Frame 116 X 45 Mm & Sash 46 X 62 Mm Both Having Wall Thickness Of 2.3 ± 0.2 Mm And Single Glazing Bead/ Double Glazing Bead Of Appropriate Dimension. (Area Of Window Above 1.75 Square meter). (HSR 12.134.4)

Providing And Fixing Factory Made Upvc White Colour Casement/ Casement Cubic meter Fixed Glazed Door Comprising Of Upvc Multi-Chambered Frame, Sash And Mullion (Where Ever Required) Extruded Profiles Duly Reinforced With 1.60 ± 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), Upvc Extruded Glazing Beads Of Appropriate Dimension, Epdm Gasket, Zinc Alloy (White Powder Coated) 3D Hinges And One Handle On Each Side Of Panels Along With Zinc Plated Mild Steel Multi Point Locking Having Transmission Gear, Cylinder With Keeps And One Side Key, G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall And Necessary Stainless Steel Screws, Etc. Profile Of Frame & Sash Shall Be Mitred Cut And Fusion Welded At All Comers, Mullion (If Required) Shall Be Also Fusion Welded Including Drilling Of Holes For Fixing Hardware'S And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealant Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single/ Double Glass Panes And Silicon Sealant Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Casement Door With Top Hung Ventilator With 3D And S.S. Friction Hinges (400 X 19 X 1.9 Mm) Made Of (Big Series) Frame 67 X 64 Mm, Sash 67 X 110 Mm & Mullion 67 X 80 Mm All Having Wall Thickness Of 2.3 ±. 0.2 Mm And Single Glazing Bead / Double Glazing Bead Of Appropriate Dimension.(Area Of Door Above 2.50 Square meter) (HSR 12.133.2)

Providing And Fixing Glazing In Aluminium / Upvc Door, Window, Ventilator Shutters And Partitions Etc. With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Architectural Drawings And The Directions Of Engineer-In-Charge . (Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item): With Float Glass Panes Of 6 Mm Thickness (Weight Not Less Than 15 Kg/Square meter) (HSR 12.159.3)

With Float Glass Panes Of 8 Mm Thickness (Weight Not Less Than 20 Kg/Square meter) (HSR 12.159.4)

Filling The Gap In Between Aluminium Frame & Adjacent Rcc/ Brick/ Stone Work By Providing Weather Silicon Sealant Over Backer Rod Of Approved Quality As Per Architectural Drawings And Direction Of Engineer-In-Charge Complete. Up To 5Mm Depth And 5 Mm Width (HSR 12.169.1)

Providing And Fixing Steel Roller For Upvc Sliding Window With Necessary Screws Etc. Complete. (HSR 12.140)

Providing And Fixing Factory Made Upvc White Colour Casement/Casement Cubic meter Fixed Glazed Windows Comprising Of Upvc Multi-Chambered Frame, Sash And Mullion (Where Ever Required) Extruded Profiles Duly Reinforced With 1.60 ± 0.2 Mm Thick Galvanized Mild Steel Section Made From Roll Forming Process Of Required Length (Shape & Size According To Upvc Profile), Upvc Extruded Glazing Beads Of Appropriate Dimension, Epdm Gasket, Stainless Steel (Ss 304 Grade) Friction Hinges, Zinc Alloy (White Powder Coated) Casement Handles, G.I Fasteners 100 X 8 Mm Size For Fixing Frame To Finished Wall, Plastic Packers, Plastic Caps And Necessary Stainless Steel Screws Etc. Profile Of Frame & Sash Shall Be Mitred Cut And Fusion Welded At All Corners, Mullion (If Required) Shall Be Also Fusion Welded Including Drilling Of Holes For Fixing Hardware'S And Drainage Of Water Etc. After Fixing Frame The Gap Between Frame And Adjacent Finished Wall Shall Be Filled With Weather Proof Silicon Sealant Over Backer Rod Of Required Size And Of Approved Quality, All Complete As Per Approved Drawing & Direction Of Engineer-In-Charge. (Single/ Double Glass Panes And Silicon Sealant Shall Be Paid Separately). Variation In Profile Dimension In Higher Side Shall Be Accepted But No Extra Payment On This Account Shall Be Made. Note: For Upvc Frame, Sash And Mullion Extruded Profiles Minus 5% Tolerance In Dimension I.E. In Depth & Width Of Profile Shall Be Acceptable. Casement Window Single Panel With S.S. Friction Hinges (400 X 19 X 1.9 Mm) Made Of (Big Series)Frame 67 X 60 Mm & Sash 67 X 80 Mm Both Having Wall Thickness Of 2.3 ± 0.2 Mm And Single Glazing Bead / Double Glazing Bead Of Appropriate Dimension. (Area Of Window Above 0.75 Square meter) (HSR 12.131.4)

Providing & Fixing Decorative High Pressure Laminated Sheet Of Plain/ Wood Grain In Gloss / Matt/ Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To Is : 2046 Type S, Including Cost Of Adhesive Of Approved Quality. 1.5 Mm Thick (HSR 12.12.1)

Steel Work Providing And Fixing Carbon Steel Galvanised ( Minimum Coating 5 Micron) Dash Fastener Of 10 Mm Dia Double Threaded 6.8 Grade (Yield Strength 480 N/Mm2), Counter Sunk Head, Comprising Of 10 Mm Dia Polyamide Pa 6 Grade Sleeve, Including Drilling Of Hole In Frame , Concrete/ Masonry, Etc. As Per Direction Of Engineer-In-Charge. (HSR 13.5.2) 10 X 80 Mm

10 X 140 Mm (HSR 13.5.4)

Structural Steel Work Riveted, Bolted Or Welded In Built Up Sections, Trusses And Framed Work, Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer All Complete. (HSR 13.28)

Steel Work In Built Up Tubular (Round, Square Or Rectangular Hollow Tubes Etc.) Trusses Etc., Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer, Including Welding And Bolted With Special Shaped Washers Etc. Complete. Hot Finished Seamless Type Tubes (HSR 13.30.2)

Providing And Fixing Stainless Steel ( Grade 304) Railing Made Of Hollow Tubes,Channels, Plates Etc., Including Welding, Grinding, Buffing, Polishing And Making Curvature (Wherever Required) And Fitting The Same With Necessary Stainless Steel Nuts And Bolts Complete, I/C Fixing The Railing With Necessary Accessories & Stainless Steel Dash Fasteners , Stainless Steel Bolts Etc., Of Required Size, On The Top Of The Floor Or The Side Of Waist Slab With Suitable Arrangement As Per Approval Of Engineer-In-Charge, (For Payment Purpose Only Weight Of Stainless Steel Members Shall Be Considered Excluding Fixing Accessories Such As Nuts, Bolts, Fasteners Etc.). (HSR 13.41)

Painting The Wooden I Metal Surface With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work. (HSR 11.82.1)

Compacting Original Ground Compaction of Earthwork Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers) (HSR 17.5.3)

Granular Sub-Base with Close Graded Material· (Table:- 400-1) Plant mix method Construction of granular sub-base by providing Material as per Grading Ill (Table 400-1 of MORT&H 5th revision) mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications Grading I material (HSR 17.14.1)

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per technical clause 406 of MORT&H specifications. (HSR 17.24)

Bituminous Concrete with Batch type HMP Bituminous Concrete 50 mm to 65 mm thickness (grading I) with 100-120 TPH batch type HMPProviding and laying 50 mm - 65 mm bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG - 30 @ 5.2% per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete in all respects as per technical clause 507 of MORT&H specifications as per MORTH specification(HSR 17.27.4)

Prime Coat @ 0.85kg per sqm Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.85 kg/sqm using mechanical means as per technical clause 503 of MORT&H specifications (HSR 17.25)

Tack coat Providing and applying tack coat with penetration grade bitumen VG-10 pressure distributor at the rate of 1.0 kg per sqm on the prepared granular surface cleaned with mechanical broom as per technical clause 503 of MORT&H specifications(HSR 17.26.3)

Dense Graded Bituminous Macadam 50 mm to 75 mm thickness (Grading II) Providing and laying 50mm - 75 mm dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG 30 @ 4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORT&H specifications. (HSR 17.30.2)

Providing and laying 80mm thick factory made cement concrete inter1ocking paver block of M -35 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (HSR 10.77)

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Wor Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS: 164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control Over 10 cm in width (HSR 34.24.1)

Water Proofing Providing And Laying Integral Cement Based Treatment For Water Proofing On Horizontal Surface At All Depth Below Ground Level For Under Ground Structures As Directed By Engineer-In-Charge And Consisting Of : (I) 1St Layer Of 22 Mm To 25 Mm Thick Approved And Specified Rough Stone Slab Over A 25 Mm Thick Base Of Cement Mortar 1 :3 (1 Cement : 3 Coarse Sand) Mixed With Water Proofing Compound Conforming To Is:2645 In The Recommended Proportion Over The Levelling Course (Levelling Course To Be Paid Separately}. Joints Sealed And Grouted With Cement Slurry Mixed With Water Proofing Compound. (Ii) 2Nd Layer Of 25 Mm Thick Cement Mortar 1 :3 (1 Cement: 3 Coarse Sand) Mixed With Water Proofing Compound In Recommended Proportions. (Iii) Finishing Top With Stone Aggregate Of 10 Mm To 12 Mm Nominal Size Spreading @ 8 Cudrn/Square meter Thoroughly Embedded In The 2Nd LayerUsing Rough Kota Stone (HSR 28.10.1)

Providing And Laying Integral Cement Based Treatment For Water Proofing On The Vertical Surface By Fixing Specified Stone Slab 22 Mm To 25 Mm Thick With Cement Slurry Mixed With Water Proofing Compound Conforming To Is:2645 In Recommended Proportions With A Gap Of 20 Mm (Minimum) Between Stone Slabs And The Receiving Surfaces And Filling The Gaps With Neat Cement Slurry Mixed With Water Proofing Compound And Finishing The Exterior Of Stone Slab With Cement Mortar 1 :3 (1 Cement : 3 Coarse Sand) 20 Mm Thick With Neat Cement Punning Mixed With Water Proofing Compound In Recommended Proportion Complete At All Levels And As Directed By Engineer-In-Charge : Using Rough Kota Stone. (HSR 28.13.1)

Providing And Applying Of Swellable Type Water Stop Tape, 19Mm X 25Mm Thick In Linear Meter (Expansive Nature) For Construction Joints Treatment Of Rcc Structure Such As Raft Slab, Retaining Walls, Water Storage Tank And At The Junctions Of Raft Slab With The Retaining Walls Etc .. After Cleaning The Surface, One Coat Of Required Primer For Swellable Water Stop Tape Shall Be Applied Throughout The Length Of The Joint @3. 78 Litre Per 240 Running Meter. Over The Primed Surface Swellable Type Water Stop Tape Shall Be Placed. The Work Shall Be Carried Out All Complete As Per Specification And The Direction Of The Engineer-In-Charge. The Product Performance Shall Carry Guarantee For 10 Years Against Any Leakage. (HSR 28.30)

Providing And Laying Water Proofing Treatment To Vertical And Horizontal Surfaces Of Depressed Portions Of W.C., Kitchen And The Like Consisting Of: (I) 1St Course Of Applying Cement Slurry @ 4.4 Kg/Square meter Mixed With Water Proofing Compound Conforming To Is 2645 In Recommended Proportions Including Rounding Off Junction Of Vertical And Horizontal Surface. (Ii) Llnd Course Of 20 Mm Cement Plaster 1 :3 (1 Cement : 3 Coarse Sand) Mixed With Water Proofing Compound In Recommended Proportion Including Rounding Off Junction Of Vertical And Horizontal Surface. (Iii) Lllrd Course Of Applying Blown Or Residual Bitumen Applied Hot At 1.7 Kg. Per Square meter Of Area. (Iv) Lvth Course Of 400 Micron Thick Pvc Sheet. (Overlaps At Joints Of Pvc Sheet Should Be 100 Mm Wide And Pasted To Each Other With Bitumen@ 1.7 Kg/Square meter). (HSR 28.14)

Providing And Laying Water Proofing Treatment On Roofs Of Slabs By Applying Cement Slurry Mixed With Water Proofing Cement Compound Consisting Of Applying: (A) After Surface Preparation, First Layer Of Slurry Of Cement @ 0.488 Kg/Square meter Mixed With Water Proofing Cement Compound @ 0.253 Kg/Square meter (B) Laying Second Layer Of Fibre Glass Cloth When The First Layer Is Still Green. Overlaps Of Joints Of Fibre Cloth Should Not Be Less Than 1 O Cm. (C) Third Layer Of 1.5 Mm Thickness Consisting Of Sluny Of Cement @ 1.289 Kg/Square meter Mixed With Water Proofing Cement Compound @ 0.670 Kg/Square meter And Coarse Sand @ 1.289 Kg/Square meter This Will Be Allowed To Air Cure For 4 Hours Followed By Water Curing For 48 Hours. The Entire Treatment Will Be Taken Up To 30 Cm On Parapet Wall And Tucked Into Groove In Parapet All Around. (D) Fourth And Final Layer Of Brick Tiling With Cement Mortar (Which Will Be Paid For Separately). For The Purpose Of Measurement The Entire Treated Surface Will Be Measured. (HSR 28.16.1)

10 Cm Thick (Average) Mud Phaska Of Damped Brick Earth On Roofs Laid To Slope Consolidated And Plastered With 25 Mm Thick Mud Mortar Mixed With Bhusa @ 35 Kg Per Cubic meter Of Earth And Gobri Leaping With Mix 1: 1 (1 Clay : 1 Cow Dung) And Covered With Flat Tile Bricks, Grouted With Cement Mortar 1 :3 (1 Cement: 3 Fine Sand) Mixed With 2% Of Integral Water Proofing Compound By Weight Of Cement And Finished Neat: With Common Burnt Clay Non-Modular Brick Tile Of Class Square meter Designation 10 (HSR 9.11.1)

Pointing On Tile Brick Work With Cement Mortar 1 :3 (1 Cement : 3 Fine Sand): Flush/ Ruled/ Struck Or Weathered Pointing. (HSR 11.26.1)

Providing And Fixing In Position 600X600X15Mm Gedina A Glasswool Ceiling Tile Of Ecophon Make With 15Mm Grid System. The Tiles Should Have Humidity Resistance Of 95% Rh, Nrc 90% (Acoustic Performance) Colour White, Fire Performance Class0/Class1 (Bs-476) In Module 600X600X15 Mm With Tissue Backing, With 15 Mm Wide Hot Dipped Galvanised Steel T Section Suspension System As Per Architects Approval At Required Spacing, Finishing Of All Joints, Cuts Made In The Tiles To Be Neatly Sealed By White Cement Leaving No Exposed Glass Wool And Made To Proper Line & Level Including Providing Of Additional Framework For Electricals Fixtures. Diffusers Cutouts For Fire Sprinklers Etc. As Per The Specifications Approved By Architects Including Necessary Scaffolding Supports, Suspenders Etc. The Installation To Comprise Of Main Runners Spaced At 1200Mm Centres Securely Fixed To The Structural Soffit By Approved Hangers At 1200 Mm Maximum Centres And Not More Than 150Mm From Spliced Joints. The Last Hanger At The End Of Each Main Runner Should Not Be Greater Than 600 Mm From The Adjacent Wall. 1200 Mm Long Cross Tees To Be Interlocked Between Main Runners At 600Mm Centres To Form 1200X 600 Mm Modules. Cross Tees Longer Than 600 Mm Require Independent Support. 600X600 Mm Modules To Be Formed By Fitting 600 Mm Long Cross Tees Centrally Between The 1200 Mm Cross Tees. The 1200 Mm Cross Tees To Have Central “Birdsmouth “ Notches To Facilitate Fitting Of 600 Mm Cross Tees.(The Work To Include Cost In All Levels Including Scaffolding). (NS)

Supply Double Skin Puf Insulated Sandwich Roof Panel Having 80 Mm Core With 0.60 Mm Tct Ppgi Trapezoidal Profiled Sheet In Top Skin And 0.60 Mm Tct Ppgi Micro Ribbed Liner Panel Sheet In Bottom Skin. The Pu Panel Shall Be Cfc Free And Zero Ozone Depleting Panel Using N Pentane Blowing Agent & Made Out Of Continuous Line Running On Uninterrupted Power Supply. Panel Shall Have Pre Coated Gi Sheet On Both Side Of Polyurethane Foam Confirming To Is 12436:1988. The Pre Coated Sheet Shall Be Of Minimum 240 Mpa Steel Grade Confirming To Is 14246:1995 And Shall Have Zinc Coating Of Minimum 120 Gsm As Per Is : 277 : 1992, 5-7 Microns Epoxy Primer On Both Side Of The Sheet And Polyester Top Coat 15-18 Micron. The Ppgi Sheet Shall Have Plastic Protective Guard Film Of Minimum 25 Microns To Avoid Scratches During Transportation. The Pu Foam Shall Be Self-Extinguishing, Type Having Minimum Density Of 40 Kg/M3 (+,-2 Kgs) .Sheets To Be Of Tata Bluescope/Jindal. (NS)

Providing And Fixing In Position At Site With Loop 26 Oz Imported Fire Retardent Carpets Of Approved Sample From Architect With Woven Polypropylene Primary And Secondary Backing With 10 Mm Thick Expanded Polyurethane Foam Sheet , Carpet And Underlay To Be Installed With Standard Fevicol/Dunlop Adhesives, The Flooring/Vertical Skirting To Be Installed As Per Manufacturer’S Specifications.(NS)

Providing And Fixing Stage Made Of 75X25 Mm Steambeech Wood Planks( Finished Exposed Size, Excluding Tongue ) Flooring With Tongue And Groove Joints ( Concealed Screwing And Minimum Length 1.0 M ) On Two Layers Of 12 Mm Thick Waterproof Duro Marine Ply, Plywood Bonded With Phenolic Resin With Joints Staggered With 2Nd Layer Glued And Screwed To Be First Fixed To Nigerian Teak Wood Joints Framework ( Painted With Viper Fire Retardent Paint ) Comprising75X50Mm Teakwood Joints 900 Mm C/Cin One Direction And 50Mm/50 Mm Teak Wood Battens 400 Mm C/C On Other Direction, Filled With One Layer Of 50 Mm Thick Resin Bonded Glass Wool Of 32 Kg/M3 Density Between The Nigerian Teak Wood Battens Grid, Teakwood Joints Resiliently Supported On 150X150 Mm Pads Of 8Mm Nominal Thickness Of Waffle, Neoprene And Ribbed Resistoflex Pads ( 50 P.S.I Grade ) Over Support Locations With Necessary Brass Screws As Per Instruction Of Architect . The Steam Beech Wood Planks Wood Be Three Phase Machine Grinded And Polished With Polyurethane Coating Lacquire Matt Finish, Fixed To The Satisfaction Of The Architect ). (NS)

Providing And Fixing Acoustic Wall Panelling Consisting Of 2X50 Mm (Making Box) In Vertical Studs Of Gi Framework Of India Gypsum Ltd Placed At 610 Mm C/C Vertically And Horizontally Fixed On Wall With Cleats (Gi Supported Systems) And Supplying And Fixing 50Mm Thick Glass Wool With Black Glass Fibre Tissue Facing (32 Kg/Cubic meter) Of U.P. Twiga And Held In Place At Rear And Front With 22 Swg X 12. X12.5 Mm Gi Chicken Wire Mesh With 25 Mm Air Gap In The Rear. In Front, Providing And Fixing Black Cotton/Jute @ Rs 50 /Rmt 40Mmx 15Mm European Steam Beech Wood Slats With Fire Retardent Paint Viperstar Over A Backing Of 12Mm Thick Duro Marine Ply Strips 100Mm Wide At 610Mm Centre To Centre Fixed With Screw/ Rawel Plugs Etc If Necessary As Per Architect’S Direction. European Steam Beech Slats To Be Melamine Matt Polished. The Gap Between The Slats To Be 8 Mm. This Paneling Is Proposed To Be Upto Ceiling Level From Ground And At All Sides Of The Front Stage From Bottom To The Ceiling. (Fixed To The Satisfaction Of Architect ).(NS)

Providing And Fixing 20 Mm Thick European Steam Beech Wood Bands /Skirting( 4" To 5") Painted With Fireretardent Viperstar Paint Of Specified Sizes Including Melamine Matt Polishing. (NS)

Providing And Fixing Stainless Steel Satin Finish Ss 304 Grade Tower Bolts Ss Screws For Wooden Doors Of Approved Make And Model All Complete As Per The Directions Of Engineer-In-Charge. (NS) 250X10 Mm

Providing And Fixing Stainless Steel Satin Finish Ss 304 Grade Handles With Ss Screws For Wooden Doors Of Approved Make And Model All Complete As Per The Directions Of Engineer-In-Charge. (NS) 125 Mm

Providing And Fixing First Class European /German Steemed Beech Wood Doors Frames Of Section 6 " X 4" With Rebate And Holdfasts Including Fixing Of Acoustic Doors Made With 65 Mm Thk With 12Mm Ply Both Side Having Insulation 40Mm Inside Thick Glass Wool With Black Glass Fibre Tissue Facing (32 Kg/Cubic meter) Of U.P. Twiga With One Layer Of 2Mm Tech Sound Sheet 2Mm Thick One Side And 1.25 Mm G.I Sheet On Other Side ( Gallery Side ) Door Of Approved Make Laminated With 1 Mm Th. Laminate Both Sides Of The Shutters With 65 X 25Mm. European /German Steemed Beech Wood Liping Alround And With Fire Rated Acoustic Activated Intumescent Fire And Smoke Seal Of Size 10Mm X 4Mm (Imported Ravan Seal As Per Approved Sample. (NS)

Providing And Fixing And Installation Auditorium Chairs Of Godrej, Wipro, Pen workers, feather light Make Jupiter Chair (inclind/tilt) With Requsite Hilti Bolts/ Dash Fastners For Mounting On The Floor Etc. Features Medium Seat/Back : The Seat Is Made Up Of 1.2 Cm Thick Marine Plywood Insitu Moulded With Polyurethane Foam And Upholstered With Fire Retardent Fabric. The Seat Is Auto Tip-Up Type And Folds When Not In Use. The Back Is Flexing Type And Made Up Of A M.S Fabricated Frame Insitu Moulded With Polyurethane Foam With Hips Vacuum Formed Back Cover. The Back Foam Is Designed With Contoured Lumber Support For Extra Comfort And Upholstered With Stitched Fabric For Enhanced Look And Comfort. Polyurethane Foam : The Polyrethane Foam Has Density = 45+/-2 Kgs/Cu.M And Hardness = 20+/-2 Kgs On Hampden M/C At 25% Compression Powder Coating : All Steel Components Are Epoxy Polyester Powder Coated With The Following Specs: Dry Film Thickness More Than 45 Microns Withstand More Than 1000 Hours In Salt Spray Test. Scratch Hardness Withstanding Upto 4 Kgs. Impact Resistance : 150 Kg.Cm. (NS)

Providing And Installation Of Funder Max For Cladding On Exterior Surface 6Mm Thick Exterior Grade F- Quality Panels Of Standard Size With Both Side Décor . The Panels Shall Be Perforated As Per The Design Of The Architect. Fundermax Exterior Panels Are Duromer High-Pressure Laminates (Hpl) As Per En 438-6 Type Edf Manufactured With Norm Conformity Of En 438-7 Using Patented Nt Technology (Nt Is Non Fading High Performance Acrylic Polyurethane Surface Technology). Panels Will Be Double Hardened Including Acrylic Polyurethane Resin And Thermally Cured Under High Pressure. These Panels Will Have Ce-Mark Necessary For Their Use In Building Applications. Installation Of Fundermax Panels Will Be Done By Mbe Rivets (With Fixed And Sliding Points) With Recommended Aluminum T Section Of 100X50X2 Mm Thick And L Section 50X50X2Mm Thick Held By Aluminum Wall Bracket With Wind Load And Dead Load Slot As Per Design, Anchored By Standard Anchor Fasteners Along With Thermal Separator. Installation Of Fundermax Panels Will Be Done Using Rear Ventilated Principles Only, Which Is Ensured By Providing Ventilation Gap Minimum 200 Cm2/ Per Meter (For Free Flow Of Air Behind The Façade) For The Façade And Using The Framework With No Horizontal Section.(NS)

Provoding And Fixing Signage In Area'S Such Lift Lobby For Floor Indication Etc. Toilet Signages (Gents)- On Door : Acrylic Ducopainted Signage With Text / Graphics In 3M Grade Vinyl Size : 200 Mm Wide X 200 Mm Tall * Sign Mounted On Door. (NS)

Provoding And Fixing Signage In Area'S Such Lift Lobby For Floor Indication Etc. Toilet Signages (Ladies)- On Door : Acrylic Ducopainted Signage With Text / Graphics In 3M Grade Vinyl Size : 200 Mm Wide X 200 Mm Tall * Sign Mounted On Door. (NS)

Floor Level Indicator - Wall Mounted : (Lift Lobby) Acrylic Ducopainted Signage With Text / Graphics In 3M Grade Vinyl Size : 317 Mm Wide X 317 Mm Tall * Sign Mounted On Wall (NS)

Floor Level Indicator - Wall Mounted : (Lift Lobby) Acrylic Ducopainted Signage With Text / Graphics In 3M Grade Vinyl Size : 317 Mm Wide X 317 Mm Tall Fire Exit Door Signages (NS)

Cabin / Room Naming (In Vinyl On Glass) : Ht. 30Mm, Font : Expert Sans Regular, Length Max. 450 Mm Ref. : Colour 100 % Cyan. 4 Colour Process C100 Mo To Ko. Rgb : R0 G164 B232. (NS)

Supply & Installtion Of Pull - Push Signages : Brush Finish Stainless Steel Etched Signs Size : 2.5"(H) X 2.5"(W) Set Includes 1 Pull & 1 Push. (NS)

Earth filling under floors with dune sand (tiba sand)/earth, brought from outside (any lead), in 15 cm layer including laying, dressing, watering ramming, consolidating, excavation, carriage, loading, unloading and compensation, etc., complete. (NS)

Earth filling under road/parking with dune sand (Tibba sand) brought from outside (any lead) in 25 cm. layer including laying, dressing, watering, rolling with road roller to specifications/ consolidating, excavation, carriage, compensation, loading and unloading, complete in all respects. (NS)

Providing and fixing factory manufactured cement concrete 1:2:4 kerb finished smooth and of size 1’-0” x 1’-0” x 0’-6” of required shape and design fixed at ground level along with road parking, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Providing and fixing factory manufactured cement concrete 1:2:4 channel finished smooth and of size 1’-0” x 1’-0” x 0’-3” of required shape and design fixed at ground level along with road, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Providing and fixing 45 mm wide solid and 30 mm wide jali Zebra type (PCL rainbow or any other equivalent make as approved by Engineer In charge) horizontal venetian blinds of required size and shape, fixed in position including rawl plugs and screws etc. complete in all respect (NS)

Public health work 132 to 247:- Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia (HSR 4.16.1.2)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 15 mm diameter pipe (HSR 11.107.1)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 20 mm diameter pipe (HSR 11.107.2)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 25 mm diameter pipe (HSR 11.107.3)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work 32 mm diameter pipe (HSR 11.107.4)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 40 mm diameter pipe (HSR 11.107.5)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 50 mm diameter pipe (HSR 11.107.6)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality 40 mm diameter pipe (HSR 11.108.5)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality 50 mm diameter pipe (HSR 11.108.6)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 32 mm internal diametre of pipeline (HSR 20.20.2.4)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 40 mm internal diametre of pipeline (HSR 20.20.2.5)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 50 mm internal diametre of pipeline (HSR 20.20.2.6)

Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS: 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge (HSR 21.28)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 150mm i/d (HSR 21.94.2)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 200mm i/d (HSR 21.94.3)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White vitreous chinaware Wash basin size 630x450 mm with a single 15 mm C. P. brass pillar tap (HSR 22.1.2)

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (HSR 22.2.1)

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 510x1040 mm bowl depth 250 mm (HSR 22.10.1.1)

Providing and fixing CP Brass Single lever telephonic wall mixer of quality &make as approved by Engineer in charge. 15 mm nominal dia (HSR 22.12.1)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia (HSR 22.14.2.1)

40 mm dia (HSR 22.14.2.2)

Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required. Single half stall urinal with 5 litre P.V.C. automatic flushing cistern (HSR 22.26.1)

Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern (HSR 22.26.3)

Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. (HSR 22.33)

Providing and fixing floor mounted, white vitreous chinaware single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous chinaware cistern of capacity10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. (HSR 22.34)

Providing and fixing toilet paper holder C.P. brass (HSR 22.42.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal outer dia Pipes (HSR 22.85.5)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes (HSR 22.86.1)

20 mm nominal outer dia Pipes (HSR 22.86.2)

25 mm nominal outer dia Pipes (HSR 22.86.3)

32 mm nominal outer dia Pipes (HSR 22.86.4)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 15 mm dia nominal bore (HSR 22.88.1)

20 mm dia nominal bore (HSR 22.88.2)

25 mm dia nominal bore (HSR 22.88.3)

32 mm dia nominal bore (HSR 22.88.4)

40 mm dia nominal bore (HSR 22.88.5)

50 mm dia nominal bore (HSR 22.88.6)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc External work 40 mm dia nominal bore (HSR 22.91.5)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc External work 50 mm dia nominal bore (HSR 22.91.6)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore (HSR 22.92.1)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 50 to 80 mm nominal bore (HSR 22.92.2)

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main 25 mm nominal bore (HSR 22.100.3)

45 cm length 15 mm nominal bore (HSR 22.101.2.1)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100 mm diameter (HSR 22.102.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (HSR 22.103.3)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore (HSR 22.104.1)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (HSR 22.106.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (HSR 22.108.1)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (HSR 22.117)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. (HSR 22.118)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms (HSR 22.119.1)

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms (HSR 22.127)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design 150 mm diameter S.W. pipe (HSR 22.164.2)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design 250 mm diameter S.W. pipe (HSR 22.164.4)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 150 mm diameter S.W. pipe (HSR 22.165.2)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 200 mm diameter S.W. pipe (HSR 22.165.3)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 300 mm diameter S.W. pipe (HSR 22.165.5)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common bumt clay non-modular bricks of class designation 7. (HSR 22.166.3.1)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 150 mm dia. R.C.C. pipe (HSR 22.168.2)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 250 mm dia. R.C.C. pipe (HSR 22.168.3)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 300 mm dia. R.C.C. pipe (HSR 22.168.4)

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1 :4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1 :2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1 :5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1 :3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.173.1)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (HSR 22.181)

Constructing brick masonry manhole in cement mortar 1 :4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1 :4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 :3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.190.1.1)

Constructing brick masonry manhole in cement mortar 1 :4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1 :4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 :3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.190.2.1)

Extra for depth for manholes : Size 90x80 cm With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.191.1.1)

Extra for depth for manholes : Size 120x90 cm With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.191.2.1)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1 :4 (1 cement : 4 coarse sand) including 500x450 mm pre­ cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.205.1)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (HSR 22.209)

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P. brass screws and rawl plugs etc. complete including cutting and making good the walls etc. C.P Brass Two Way (HSR 22.212.1.2)

Providing and fixing in position best Indian make (to the approval of the engineer-in-charge) storage type automatic electric water heater, pressure/non-pressure type thermostatically controlled, suitable for operation on 230 volts, 50 cycles single phase vertical wall mounting fitted with-draw able and adjustable type AC, thermostat. Thermostat knob to be readily accessible through the opening of suitable cover for and adjustment of temperature in the installed position of heater and the thermostat should be withdrawn without having to drain the water, electric heating element made out of copper tube (heating element should be easily removed and replaced in the installed position of heater) A neon indicator 1 AMP, inner container made out of copper tinned both from inside and outside, outer container made out of mild steel sheet finished in gleaming white stove enamel paint, insulated between the inner and outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord with plug and non return valve plastic/lead connections or pressure release valve (where required). Complete including fixing and testing for a week (as required by Engineer-incharge. 30 Litres capacity (HSR 22.216.2)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 160 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.1)

110 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.2)

90 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.3)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 metre depth below ground level. All types of soil 400 mm dia (HSR 33.6.1.3)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & up to 150 metre depth below ground level. All types of soil 400 mm dia (HSR 33.7.1.3)

Supplying, assembling, lowering and fixing in vertical position in bore well, Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia (HSR 33.8.3)

Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia (HSR 33.9.3)

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. (HSR 33.12)

Supplying, filling, spreading & levelling gravels of size range 5 mm to 1 O mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (HSR 33.13)

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (HSR 33.14)

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. (HSR 33.15)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 200 mm dia (HSR 33.16.3)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete 200 mm clamp (HSR 33.17.3)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 200 mm dia (HSR 33.18.3)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yieldwithout sand content (beyond permissible limit), with requiredcapacity air compressor, running the compressor for requiredtime till well is fully developed, measuring yield of well by "V''notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. (HSR 33.19)

Providing and fixing C.P brass health Fancet with 1 mtr flexible tube and swivel hook including all fittings, complete in all respect. (NS) Make:- Jaquar/Hindware

Providing and fixing stainless steel 600 mm Grab Bar with 2 mtr C.P brass wall flanges including cutting and making good the walls wherever required, complete in all respect (NS) Make:- Jaquar/Hindware

Providing and fixing water purifier cum water cooler made of fully stainless steel body having storage capacity of 80 ltrs & cooling capacity 60 ltrs/hour with reverse osmosis system. (NS) Make:-Bluestar/Voltas/Usha Kent/Aquaguard

Supply of UPVC pipe 6 kg/cm² pressure (as per IS: 4985 Class-II) of Prince / Supreme/Skipper/Finolex make (as approved by the Engineer-in-Charge). (NS) a) 40 mm o/dia size (32 mm i/dia)

(b) 50 mm o/dia size (40 mm i/dia)

c) 63 mm o/dia size (50 mm i/dia)

Providing and fixing in position UPVC 'P' or 'S' trap of self cleaning design of 110 mm inlet and 110 mm outlet for embeded areas and making connection with chemical sealent joint, cutting chase/hole in floor/slabs etc.and making good in cc 1:2:4 complete in all respect.(NS)

Providing and fixing in position UPVC floor drain including cost of cutting and making good the wall and floors wherever required. 110 mm inlet and 63 mm outlet (NS)

Providing and fixing UPVC clean out plug (ceiling or floor) with suitable insert keys for opening male threaded joint with UPVC socket fixed to UPVC pipe complete in all respect. (NS) (a) 110 mm dia

(b) 160 mm dia

Providing and fixing stainless steel Grade (304) grating with ring and stainless steel anti cockroach basket and two stainless steel screw including fixing to the floor with cement morter. (NS)

Providing and fixing thermoflex or careflex thermal insulation tubing, a elastromeric flexible material having hermatix blister closed cell structure of expanded synthetic rubber over pipes of following sizes and thickness including all required accessories. (a) For 15 mm dia pipes (NS)

(b) For 20 mm dia pipes

Providing and fixing commissioning of motorised butterfly valves (for filling of overhead tanks) complete with high and low level control switches to control tanks the level controller shall be installed in overhead tanks, the level switch will close the valve when water level is high and open the valve when water level in tank is low, the system should be complete in all respect with accessories 220V AC/ 24V DC/IP 67 electrical water level control unit, copper control wiring in whether proof casing etc. Make:- Belimo/Audco/ Advance/ AIP. (NS) (a) 40 mm dia pipe

(b) 50 mm dia pipe

Providing and fixing Full way lever operated brass ball valves of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 15kg/sq cm with threaded/ flanged points complete with nuts, bolts, gasket, washers etc. (NS) (a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 32 mm dia

(e) 40 mm dia

(f) 50 mm dia

Providing and fixing G.I pipes complete (15:1239 medium class) with G.I fittings coupling to 15:1879 and clamps including M.Spipe supports, paiting with two or more coats of synthetic enamal paint including one coat of primer and cutting and making good the walls etc. complete internal work:- Exposed on wall. (NS) (a) 65 mm dia pipe

(b) 80 mm dia pipe

(c) 100 mm dia pipe

Providing and fixing C.I butyterfly valves lever operated PN-1.6 complete with bolts, nuts 1.5 mm thick compressed asbestos gasket and two nos flanges etc. complete in all respect. (NS) (a) 65 mm dia nominal bore

(b) 80 mm dia nominal bore

(c) 100 mm dia nominal bore

Making connection of drain or sewerline with existing man hole including breaking into and making good the walls, floors with c.c. 1:2:4 course sand mix cement plaster on both side 1:3, finished with a floating coat of neat cement and making necessary channel and drain etc. complete in all respect. (NS) (i) For pipes100 to 250 mm dia

(ii) For pipes 250 to 300 mm dia

Electrical work 248 to 492:- COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS)Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe Group B (HSR 23.3.1.2)

Wiring for Twin control light point with 2 Eachs , 2-ways, 5 amp. switch in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC ( 23.3.2 ) conduit pipe. Group B (HSR 23.3.2.2 )

Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch( HSR 23.3.3 ) Group B ( HSR 23.3.3.2 )

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 Each 1.5 sqmm FRLS copper wire and 1 Each 1.5 Sqmm FRLS copper wire , including providing 1 Each 5/6 Amp 3/5 pin socket and 1 Each 5/6 Amp switch required MS Box etc complete as required. Group B (HSR 23.3.4.2)

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 Each 4 sqmm FRLS copper wire and 1 Each 4 Sqmm FRLS copper wire for earthling , including providing 1 Each 15/16 Amp 3/6 pin socket and 1 Each 15/16 Amp switch required MS Box etc complete as required Group B (HSR 23.3.5.2)

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of size 1.50 sqmm ( 1/1.40mm ) (HSR 23.3.6.1 )

1 run of size 2.50 sqmm ( 1/1.80mm ) (HSR 23.3.6.2 )

1 run of size 4.0 sqmm ( 1/1.80mm ) (HSR 23.3.6.3)

2 run of size 1.50 sqmm ( 1/1.40mm ) (HSR 23.3.6.6)

PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS Supply and erection of PVC conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. (HSR 23.7.6.2 )

S/E of Fittings and Accessories. Electric buzzer 220/230 volts A.C. Bakelite with double coil. (HSR 23.8.1.7)

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C.slab for the erection of fan complete with all labour and material required to complete the job. ( HSR 23.8.4)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. i) 1 & 2 Modules (HSR 23.8.10.1 )

3 Modules (HSR 23.8.10.2)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. I ) step type Fan Regulator 2 modules 300 watt ( HSR 23.8.11.7 )

Blanking plate (HSR 23.8.11.10 )

Telephone Socket outlet modular type ( HSR 23.8.11.8 )

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work ( HSR 23.22.1 ) i ) TRIPLE POLE MCCB 16 to 100 Amp, 25 KA ( HSR 23.22.1.3 )

TRIPLE POLE MCCB 200 to 250 Amp, 25 KA ( HSR 23.22.1.5 )

TRIPLE POLE MCCB 300 to 400 Amp, 25 KA ( HSR 23.22.1.6 )

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:-( HSR 23.22.5 ) i ) SP MCB 6-32 AMP ( HSR 23.22.5.1 )

TPN MCB 40-63 AMP ( HSR 23.22.5.6 )

Miscellaneous.Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channe l and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-incharge of the work.( HSR 23.23.8 ) i ) 2 pair telephonewire ( HSR 23.23.8.1 )

EARTHING AND LIGHTINING ARRESTOR Earthing with tinned copper earth plate 600mm x600 mmx 3 mm thick including accessories and provinding masonry enclosures with cover plate having locking arrrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required. ( HSR 24.1.4 )

Extra for charcoal or coke and salt for G.I./Copper plate earth electrode. ( HSR 24.1.5 )

Providing and fixing 25mm x 5mm copper strip in 40mm dia G.I.pipe from earth electrode as required.( HSR 24.1.9 )

Providing and fixing 25mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material.( HSR 24.1.10 )

Pdg and laying earth connections from earth electrode with 4.00 mm dia G.I wire in 15 mm dia G.I. pipe from earth electrode as required. ( HSR 24.1.11 )

pdg and fixing 4.00 mm dia G.I. wire on surface or in recess for loop earthing as required. ( HSR 24.1.13 )

STREET LIGHTSupply and erection of suitable compression type brass cable glands for underground Cable :- ( HSR 24.2.7 ) I ) 10 sqmm to 16 sqmm cable 2 to 4 core ( HSR 24.2.7.2 )

25 sqmm to 50 sqmm cable 2 to 4 core ( HSR 24.2.7.3 )

240 sqmm cable 3 to 3½ Core ( HSR 24.2.7.6 )

300 sqmm to 400 sqmm Cable 3 to 3½ Core ( HSR 24.2.7.7 )

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work.( HSR 24.2.8 ) I ) 16 sqmm ( HSR 24.2.8.4 )

50 sqmm ( HSR 24.2.8.7 )

240 sqmm ( HSR 24.2.8.13 )

400 sqmm ( HSR 24.2.8.15 )

Pdg. And fixing of insulated rubber mating suitable for 11 KV installation 1 M x 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per directions of Engineer-in-charge (HSR 20.84 )

DG SETS : Designing , Supply & erection of DG set of capacity given below with Eachise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 +(-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel , making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer , outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge . The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 V. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator, control fuse, frequency meter, CT's) h) Metering set 60/5A/110V (Amp. Meter, Volt Meter) i) Overload protection for DC-1 Each. j) Battery Charger 24V DC k) Copper bus bar of suitable size I) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running , load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge Make:- Kirloskar, Cummins i ) 125 KVA ( HSR 20.89.7 )

RCC FOUNDATIONS FOR DG SET Providing RCC foundation of M20 grade (1 Cement:1.5 Stone aggregate: 3 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 50 kg/cum of concrete contents, concrete cover 50mm, over a bed of 75mm thick PCC 1:5:10, of required dimensions as per OEM recommendations to provide levelled surface for placement of the DG set complete in all respects and as per directions of Engineer-in-charge (Size of foundation assumed = 5.0x1.8x1.0m) Unit: per cum ( HSR 24.7 ) i 0 125KVA DG Set ( HSR 24.7.5 )

S/E of mark double walled corrugated ( DWC) HDPE pipe 10 kg/sqcm, laid 0.75 Mtr. Below ground level including diging and refilling of earth including cost of suitable size socket/ cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer incharge of the work. ( HSR 24.5.2 ) i ) DWC/HDPE pipe 63/50 mm outer dia/inner dia ( HSR 24.5.2.3 )

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 4x16 sqmm (Armoured) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 4x25 sqmm (Armoured) (NS) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 4x70 sqmm (Armoured) (NS) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 3.5x240 sqmm (Armoured) (NS) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable laid 1 mtr below ground level with sand and bricks including refilling of trench complete with necessary connecitons:- Size 3.5x240 sqmm (Armoured) (NS) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 3.5x185 sqmm (Armoured) (NS) Make:-CCl,Havells,FiEachlex

Supply & erection of under ground cable laid 1 mtr below ground level with sand and bricks including refilling of trench complete with necessary connecitons:- (NS) Size 3.5x185 sqmm (Armoured) Make:-CCl,Havells,FiEachlex

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe.(NS) Size 1.5 sqmm Make:-Havells,FiEachlex,Powerage,RR

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 04 sqmm Make:-Havells,FiEachlex,Powerage,RR

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 06 sqmm Make:-Havells,FiEachlex,Powerage,RR

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe.(NS) Size 16 sqmm Make:-Havells,FiEachlex,Powerage,RR

Supply installation testingan commissioning of wall free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2 mm thick CRCA sheet required hardware 3 mm thick bakelite sheet providing all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of zinc/Red oxide primer followed by 2 coats of powder cating in grey or required shade after rinsing. the panle having PU/Neoprene rubber gasket of Eacht less than 3 mm thickness separate detachable gland plate MS base channel hinged door with inter locking arrangement for equipment/ switch wear.Transparent arcylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3 mm thick for separately cable alley to BBC from switch chamber Extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra tiems side walls and cable alley compartments shall be haiving bolted type doors with detachable extension type strcture. the panel will be complete with control wiring ( copper) and fuse protection ( only outer area on all sides shall be measured ) (NS)

Supply and fixing of copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing go same in existing panel including bending, cutting in required shape and size and insulation with colour coding heat srinkable PVC insulation complete in all respect. (NS)

S/E of AC ceiling fan capacitor type complete with shackle 5 star rating, 300mm down rod etc.(NS) i) 1200mm sweep. Make: Usha, Orient, Crompton

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod etc.(NS) i) 1400mm sweep. Make: Usha, Orient, Crompton

S/E of LED tube rod ≤ 36watt double side connections with 4 feet long housing made of CRCA sheet steel with epoxy powder coated white after phosphochromate treatment and type white polycarbonate holders and reflector made of white powder coated CRCA sheet total system lumen of 36watt LED should be >4000 or above in cool day light ( 5700K to 6500K ) PF > 0.95 , CRI >80 , Avg. life >50000 hours complete with mounting bracket and accessories as required with connections Make PhilIphs , Havells , wipro , Bajaj ( NS )

S/E of recessed type ≤42 watt full window glare free opal difffuse LED panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 5100 or above in cool day light (5600k to 6500k), Power factor >0.95, CRI (Ra) >80, LED lamp efficiency ≥140 lm/w, Average life >50000hours, complete with all accessories. (Industrial) Make Havell's or Philiphs , Bajaj (NS)

S/E of Exhaust Fan size 300mm 12" With necessary earthing arrangements of fan with shutter complete in all respects Size 12" sweep Heavy duty 900RPM Make Orient , Usha , Khaitan ,Crompton (NS)

SITC of Power Distribution Electrical panel having a Incomer of 125A. Floor mount / rack mount / wall mount. Miniature circuit brakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures.Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V confirming to IS 694 and IS 8130 All welding slag grounded off and welding pits wiped smooth with plumber metal.Power panels shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component does Eacht attain temperature more than 40 degree Celsius.Fabricated panel shall be supported with ms angles of size 25mm x 25mm with an 1.8mm thickness sheet to hold the structure. using incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization Individual MCB control for 38 outgoing circuits RYB Phase indicators internally wired using IS certified wires and cables. Terminal for both incoming and outgoing cable shall be suitable for 1100 volts grade, aluminum/copper conductor PVC insulated and sheathed, armoured cable and shall be suitable for connections. Provided with ivery connectors for the internal terminations and external outgoing connecting points Custom built as per specification and project requirement.

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 300 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid. Make: Custom (NS)

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 75 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid. Make: Custom (NS)

SITC of FRLS Copper unarmoured Flexible cable sheilded IS694 having 12 Core each of 1.5 Sq mm size. Make: Polycab / Walna / SBEE/RR/Havells (NS)

Supply installation testing & Commissining of Advance Lightening Protection System ,the System Should be capable of protecting against direct lightning points as well as conducting / diverting it to Earth completely after tracing the lightning in advance having following specifications:System Components: the system should consist of the following components for Performing the desired task as above in the scope. Early streamer emission Air terminal ION Streamer 1.5 with following features: Stainless steel central capture head of 316 L Other avoiding bolting and water infiltration that can cause premature corrosion Ion Generator Device Eachn electronics type for Early Streamer Emission.Control over the release of ions Positive or negative.NFC 17:102Area coverage upto 107 Radius Mtrs.System should Eacht depend on Electrical energy.Mas of 40mm dia with 5 Mtr. Length with 80-100 micron Hot Dip Galvanized along with length and base plate. Number of counts - 6 digits Current sensitivity - 1 KA to 200 KA, 8/20u/sec.Inductance Shunt - 0.5 micro Henry Enclosure - IP 67 Each external power source is requiredDOWN CONDUCTOR – It should consist of the following:-70sqmm PVC insulated copper cable. (Length as per site requirement.)Grounding System2 Each. of Copper Bonded Earth Rod of 10 feet length, 17 mm dia earth electrode made of high tensile low carbon steel circular rods, molecularly bonded copper on outer surface (minimum copper bonding thickness-250 microns) should be tested on at least 25KA fault current by CPRI and certified by UL comply to UL467 standard. With 50kg Eco friendly earth enhancing compound with each rod tested by ROHS comply to IEC 62651-7 should have passed Leaching,Corrosion,Sulphur & Resistivity Test as per IEC 62561-7 by NABL accredit Lab with exothermically welded with Copper Bus Bar of 25x3mm for connection.

S/I/T/C of Power Dimming Modules(DMX), for dimming 26/36watts LED, WITH Scene controller and accessories as required with connections including all petty material required to complete the job upto entire satisfaction of EIC.including all petty material required to complete the job upto entire satisfaction of EIC. Make LUTRON (NS)

S/I/T/C of 36W LED recessed/ mounted downlighter with DALI Dimmable driver etc. complete in all respect (Cool White) 36watt LED should be >3623 or above in cool day light 3000K PF > 0.99 , CRI >80 , Avg. life >50000 hours voltage 85-265VC , Beam Angle 120 degree , UGR 19 , 100lm/watt , opel diffuser , Al./PC housing , 30 life expetancy Frequency 50Hz complete with mounting bracket and accessories as required with connections including all petty material required to complete the job upto entire satisfaction of EIC.(NS)

S/I/T/C of 36W LED recessed/ mounted downlighter with DALI Dimmable driver etc. complete in all respect (Warm White)should be >3623 or above in cool day light 6000K PF > 0.99 , CRI >80 , Avg. life >50000 hours voltage 85-265VC , Beam Angle 120 degree , UGR 19 , 100lm/watt , opel diffuser , Al./PC housing , 30 life expetancy Frequency 50Hz complete with mounting bracket and accessories as required with connections including all petty material required to complete the job upto entire satisfaction of EIC. including all petty material required to complete the job upto entire satisfaction of EIC.(NS)

S/I/T/C of 26/24W LED recessed mounted downlighter/ WALL WASHER with driver complete in all respect (Warm White)should be >2600 or above in cool day light 3000K PF > 0.99 , CRI >80 , Avg. life >50000 hours voltage 85-265VC , Beam Angle 120 degree , UGR 19 , 100lm/watt , opel diffuser , Al./PC housing , Frequency 50Hz complete with mounting bracket and accessories as required with connections including all petty material required to complete the job upto entire satisfaction of EIC.(NS)

S/I/T/C of 18W LED recessed mounted downlighter (Warm White)should be >2000 or above in cool day light 3000K PF > 0.99 , CRI >80 , Avg. life >50000 hours voltage 85-265VC , Beam Angle 120 degree , UGR 19 , 110lm/watt , opel diffuser , Al./PC housing , Frequency 50Hz complete with mounting bracket and accessories as required with connections including all petty material required to complete the job upto entire satisfaction of EIC.(NS)

S/I/T/C of Self contained single sided exit sign green in color for wall / ceiling / pendant cantilever mounting with 3W LED with maintenance free battery with backup 2-3 hours duration ,connection testing etc as reqd.including all petty material required to complete the job upto entire satisfaction of EIC.

S/I/T/C of step lights 75mm wide & 1000mm long made out of extruded aluminium in step corner form with 15-20mm overhang over the raiser. Consisting of 1W LED fixed at top with acrylic sheet having chair number embossed on it. The down Eachse to have 6 Eachs 1 watt LED to illuminate the step riser. including all petty material required to complete the job upto entire satisfaction of EIC.

S/I/T/C of LED Cove Light strips for coves 60LED per mtr. ( Each of 5mtr size) including all petty material required to complete the job upto entire satisfaction of EIC.

S/I/T/C of Drivers suitable for LED step lights ( 1 Driver of suitable capacity to lit 10 Each Steps Lights )including all petty material required to complete the job upto entire satisfaction of EIC.

S/E of fancy pole of 3 mtr long made of cast iron base part and mild steel grooved pipe section and joined together by means of threaded joints alongwith a service window provided in the bottom part of the pole to accomadate a 6 amp. SP MCB and 30 amp. Connector for mains connection. A cast aluminium embellishment shall be fitted to the grooved steel pole by grub screw fixing to enhance the decorative look of the pole. The Pole shall be duly pre-treated by shot blasting process and painted in Poly-Urethane paint in approved colour shade having a minimum 300 salt spray hours quoting on the pole and should have minimum 90 micrones DFT. Pole Make : Twinkle, Homdec Lighting LED. Specifications:- LED should be ≤ 30 watt with cast amuminium housing diffuser translucent poly carbonate having quoting PU/Polyster LED should be ≤ 30 watt with seprate driver placed integrally in luminaire housing. Driver should be of THD ≤10% and power factor above ≥ 0.95, provided. LED lumen should be ≥ 3600. The luminaire Urethane/Polyster quoting in required colour shade. LED CCT should be 3000K ingress protection IP 65, power rating 230 volts, AC 50 HZ. LED including cost of suitable foundation as per pole design Make :TWINKLE/K-LITE

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- Size 2x16 sqmm (Armoured) Make:-CCl,Havells,FiEachlex

SITC of IP paEachramic camera shall be discreet, aesthetic, low-profile camera for indoor use. The 1/2.3-inch CMOS 12MP sensor operating at 30 fps provides full paEachramic surveillance with complete area coverage. Used pixels 3000 x 3000. Lens 1.26 mm fixed-focus lens (IR corrected). 360° Infrared Illumination 20m ; Dynamic range 120 dB WDR. Video compression H.265; M-JPEG.Multiple channels with edge dewarping. Regions of Interest (ROI). Intelligent Video Analysis Features (min. 6 rules simultaneously) :- Rule based alarms and tracking Line crossing Enter /leave field Follow route Loitering Idle / removed object People counting Crowd density estimation 3D tracking; Object filters: Duration, Size, Aspect ratio, Speed, Direction, Color, Object classes ; with on board Machine learning processor (camera trainer) ; 3 built-in digital Micro Electro-Mechanical System (MEMS) microphones; Calibration / Geolocation Automatic based on gyro /accelerometer data and camera height. HDMI Output. Operating temperature -40ºC to +55ºC; Operating humidity 5% to 93% RH Eachn-condensing. IP66 and IK10 Certificates: UL, FCC, EN Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply of HD IP Dome camera with1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.24 lx (color) 0.05 lx (moEach) ,IR range 15 mtrs, Dynamic range 120 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering ,People Counting; Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Lens 2.8 mm, True day/night, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording); Each cable pigtail ; Memory card slot (support upto 1TB), 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE, UL, FCC Certified. IK08 Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply of HD IP Dome camera with1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.24 lx (color) 0.05 lx (moEach), Dynamic range 120 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering, People Counting; Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Lens 2.3 mm, True day/night, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording); Each cable pigtail ; Memory card slot (support upto 1TB), 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE, UL, FCC Certified. IK08 Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply of HD Outdoor IR IP bullet camera with 1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.4 lx (color) 0.05 lx (moEach) ,IR range 30 mtrs, Dynamic range 100 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering , Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Auto Varifocal Lens (zoom / focus) 3.5mm to 10 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording), 5s pre-alarm recording Memory card slot support upto 512 GB , IP66 , ONVIF Profile S, CE, UL, FCC Certified. IP66 , IK 10 Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply of Outdoor IR HD PTZ Camera with 1/2" progressive scan Exmor CMOS, Effective pixels 2560 x 1440, 30x Optical Zoom 6.6mm - 198 mm;°, 16X Digital Zoom, Minimum Illumination- Sense up on- Color: 0.05 lux , B/W: 0.01 lux, With infrared (IR) 0 lux, WDR 130dB, Video Analysis ( Object removal , Loitering , Enter or Exit from the Field , Object Classification etc.) Intelligent Dynamic Eachise Reduction, BLC, White Balance, Mechanical switchable IR filter, Pan Range 360° continuous, Tilt Range 0°–90°, Pan/Tilt Modes - Pan: 0.1°/s - 240°/s; Tilt: 0.1°/s - 120°/s, Presets 256 , Tours, IR distance 300 mtrs, IR can be internal or external with full 360 deg PAN coverage; White Led 60m; Audio- 1/1 Channel In/Out, Memory card slot (support upto 1TB) , 24 individually configurable privacy masks, Simple single cable installation with POE+ support for Outdoor application, wiper, Defog, IP66 , ONVIF Profiles S & G, CE, UL Certified. Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply, Installation, Testing & Commissioning of Monitoring Software Client along with Workstation PC with PROCESSOR Intel i CORE i7- 11th generation Processor, FSB SPEED 1333 MHz, OPERATING SYSTEM Windows 10 Professional (64-bit), CHIPSET Intel Q67 Express or Better (4x2GB) RAM dual Ethernet port, HD Graphics Card with dual monitor support with 21" LED Monitor complete in all respects etc. as reqd. Makes :- HP / Dell / leEachvo/ IBM / Fujitsu / HCL

Supply, Installation, Testing & Commissioning of Full HD, High Resolution 46 - 48 inch LED professional display panel with brightness 500 nits or better; Resolution 1920 x 1080; with on screen adjustment menu, with wall mount kit complete in all respects etc. as reqd. (NS) Makes :- Samsung / LG / Panasonic/ Sharp / NEC

Supply, installation, testing & commissioning of 27U suitable MS Rack having facility to accommodate control equipment as mentioned above.

Supply, Installation, Testing & Commissioning of 6U Rack with all Accessories., as per specs complete etc. As required.

Supply, Installation, Testing & Commissioning of Category 6A field termination plug designed to support 10 Gigabit networks that can be easily terminated using parallel jaw pliers. The IDC is designed to accommodate different diameter conductors from 22 AWG-26 AWG Solid Wire. The Field Terminable Plug should be downward compatible to Cat 5e/6 and must meet IEC 60603-7-5 and must be UL Listed. plug protection: IP 20 Field Termination plug: TIA-568-C.2 CAT 6A Supporting cable diameter: 6~9 mm Plug Housing: Zinc alloy current rating: 1.5 A Dielectric withstanding voltage: 1000V DC Insulation resistance: 500M Ω MIN. Contact resistance: 20m Ω MAX Make: Belden/Panduit/Molex/Siemon

Supply, Installation, Testing & Commissioning of CAT 6A U/FTP Cable which is specifically designed to support high speed data network applications such as 10-Gigabit Ethernet (10GBASE-T). Cable should have constructed of 4 screened pairs and a drain wire. This cable minimizes alien crosstalk, provides excellent signal isolation and provides superior electromagnetic interference (EMI) protection. Enhanced performance 4 pair U/FTP LS0H cable Applications: Category 6A U/FTP Cable is intended for high speed data applications up to 500MHz including:IEEE 802.3bt (POE++) IEEE 802.3 10GBASE-T 10Gb/s IEEE 802.3 1000BASE-T 1Gb/s UL Listed Electrical/Optical Characteristics: Power: 96watt Capacitance: 40 pF/m Eachm. @1 KHz.DC Resistance: 72 Ω/Km max complies to ROHS Make: Belden/Panduit/Molex/Siemon

Supply, Installation, Testing & Commissioning of CAT 6A S/FTP Patch Cord 1 mtr. Cable conductor Size: 24-26AWG Stranded bare copper with Pre Terminated with RJ 45 Plug. Screen materials Aluminum/polyester shield with tinned copper drain wire. Operating life: 750 insertion cycles RJ45 plug material: Clear polycarbonate (PC) Boot material: Clear polyvinylchloride (PVC) Contact material: 0.35mm thick copper Contact plating: 1.27um gold RJ45 plug dimensions compliant with: ISO/IEC 60603-7 and FCC 47 Part 68 Temperature -20°C to +60°C RJ45 Plug dimensions compliant with ISO/IEC 60603-7 and FCC 47 Part 68 Fire Propagation Tests: IEC 60332-1, IEC 61034-2 Electrical Characteristics: Max Voltage: 150 VAC (max), Max Current: 1.5A @ 25°C; RoHS Compliant; UL Listed Make: Belden/Panduit/Molex/Siemon

Supply, Installation, Testing & Commissioning of CAT 6A S/FTP Patch Cord 5 mtr. Cable conductor Size: 24-26AWG Stranded bare copper with Pre Terminated with RJ 45 Plug. Screen materials Aluminum/polyester shield with tinned copper drain wire. Operating life: 750 insertion cycles RJ45 plug material: Clear polycarbonate (PC) Boot material: Clear polyvinylchloride (PVC) Contact material: 0.35mm thick copper Contact plating: 1.27um gold RJ45 plug dimensions compliant with: ISO/IEC 60603-7 and FCC 47 Part 68 Temperature -20°C to +60°C RJ45 Plug dimensions compliant with ISO/IEC 60603-7 and FCC 47 Part 68 Fire Propagation Tests: IEC 60332-1, IEC 61034-2 Electrical Characteristics: Max Voltage: 150 VAC (max), Max Current: 1.5A @ 25°C RoHS Compliant UL Listed Make: Belden/Panduit/Molex/Siemon

Front of House Left / right Array Speaker Set :-Supply, installation, testing & Commissioning of stage left cluster having 14" or dual 10" or better LF driver and multiple MF/HF drivers (More than 4), Bi-amplified 2 or 3 Way array loudspeaker system, with Individual Module free field Frequency Range (-10dB) of 60Hz - 18kHz or better & Continuous Power Handling of >= 600W LF + 150W MF/HF. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 130 or better. It should have a Horizontal near dispersion pattern of 100º or better, vertical dispersion of the array shall be 60 degrees or better. The Modules shall be of Baltic birch plywood construction with internal metal bracing. All OEMs shall offer a suitable number of modules to achieve the required vertical angle (Minimum of 2 array modules) including all petty material required to complete the job upto entire satisfaction of EIC. including of OEM flying array frame and other necessary hardware for suspending main speaker arrays. All necessary hardware to be included to achieve a safety factor of 8:1 or better. including all petty material required to complete the job upto entire satisfaction of EIC. Make Bose / L Acoustics / D&B Audiotechnik

Sub-woofer :- Supply, installation, testing & Commissioning of a single 18" subwoofer. The louspeaker shall meet the following criteria: usable Frequency Range (-10 dB) of 28 Hz - 200Hz or better. It should have an axial Sensitivity of > = 92dB (1W/1m) or more delivering a free field Max. Calculated SPL(peak) of >=127 db or better. The loudspeaker should have a Eachminal impedance: 4/8 ohm and continuous Power Handling of 750W or more; Complete with installation accessories as per the site requirement. including all petty material required to complete the job upto entire satisfaction of EIC. Make Bose / L Acoustics / D&B Audiotechnik

Stage Monitor :- Supply, installation, testing and commissioning of a two-way 8 to 10" LF, or better high SPL stage monitor loudspeaker. The louspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of 80Hz - 18 kHz or better; Eachminal Dispersion : 90°H x 60°V or better; Power handling of 800W peak or more; Sensitivity : 92 dB or better; Max SPL : 122dB Peak or more with a Eachminal impedence of 8 ohms. Standard accessories shall be included including all petty material required to complete the job upto entire satisfaction of EIC. Make Bose / L Acoustics / D&B Audiotechnik

AMPLIFIER For Mains & Sub Woofers :- SITC of 8 channel class D Networkable Power amplifier with a Max Output Power of 8x500W@8 ohms, or bridged mode output power of 4x 1000W @ 8/4 ohms. 20Hz - 20 KHz, SNR of 102dB and THD + N of <0.4% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Shall offer optional Network audio connectivity (Dante or CobraNet) through expansion slot. including all petty material required to complete the job upto entire satisfaction of EIC. Make Bose / L Acoustics / D&B Audiotechnik

AMPLIFIER GREEN ROOM SPEAKERS :- Supply, Installation, testing and commissioning of intregrated high impedence Class D zone amplifier with output power of upto 90W @ 70/100V. frequency response of 50Hz to 20kHz; THD <0.3%; Shall include priority override and Fire alarm interface, shall include necessary loudspeaker EQs. including all petty material required to complete the job upto entire satisfaction of EIC. Make Bose / Extron / Biamp

MICROPHONE :- SITC of wireless handheld microphone with (UHF) Diversity receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Cardioid , Carrier frequency range 500Mhz to 865Mhz , Frequency response 45–15kHz, Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Transmitter , Receiver dynamic range 106 dB (A-weighted) Or better, switching bandwidth Minimum 40 Mhz Or better. including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of wireless Lapel microphone, with (UHF) Diversity receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Omnidirectional, Carrier frequency range 500Mhz to 865Mhz, Frequency response 45–15kHz, Mute Button on Transmitter, Battery Operation time Minimum 8hr , Should have Charging Contact in Body pack Transmitter, Receiver dynamic range 106dB (A-weighted) switching bandwidth Minimum 40Mhz Or better. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of wireless Headword microphone with (UHF) Diversity receiver,12 Channel Present or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Supercardioid, Carrier frequency range 500Mhz to 865Mhz , Frequency response 45–15kHz, Mute Button on Transmitter, Battery Operation time Minimum 8hr, Should have Charging Contact in Transmitter, Receiver dynamic range 106 dB (A-weighted) Or better, switching bandwidth Minimum 40mHz Mhz Or better. including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of 6-way wideband antenna splitter for wireless systems with BNC-connector, 8V DC bias with range of 470 to 832 MHz. including all petty material required to complete the job upto entire satisfaction of EIC.

MICROPHONE :- SITC of Passive omnidirectional wideband antenna, for wireless systems with BNC connector, incl. stand adaptor including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of Wideband antenna amplifier for wireless systems with BNC connector, 5 dB/ 10 dB/ 15 dB switchable gain, feeding from antenna cable or external power supply including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of Mounting kit for Antenna including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of Antenna Cable 25m. including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of Wired Vocal Microphone with On/Off switch, Transducer type: Dynamic, Polar pattern: Cardioid, Frequency response: 50 - 17,000 Hz, Open circuit voltage : 2.4 mV/Pa (-52.5 dBV) ±3 dB, Eachminal impedance 600 Ω, Connection: XLR, 3-pin, male, etc. complete with installation as per the site requirement. including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of Instrument Microphone with high-frequency reproduction Polar Pattern: Cardioid, Frequency response : 33-19,000 Hz, Open circuit voltage : 2.7 mV/Pa (-51.4 dBV), Eachminal impedance : 600 Ω, Load impedance : ≥ 2 kΩ, Connection : XLR, 3-pin, male, etc. complete with installation as per the site requirement. including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of drum microphone set consisting of 7 microphones, incl. microphone clamps and rugged softbag including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MICROPHONE :- SITC of headphone, closed systems, Transducer type: Dynamic, Eachminal frequency response: .5-35,000Hz, Eachminal impedance : 80Ω, straight single sided cable 3 m (9.8 ft.) with stereo mini-jack / 1/4" adapter including all petty material required to complete the job upto entire satisfaction of EIC. Make Beyerdynamic / Sennheiser / Shure

MIXER :- Supply, installation, testing and commissioning of Digital Audio Mixer with 32-40 input Digital Mixing Console and USB Interface and 32 programmable Preamps, 24 or better Motorized Faders, 40 DSP input channels (32 moEach inputs and 4 stereo channels/returns), Channel LCD's, FireWire/USB Audio Interface and iPad/iPhone* Remote Control include I/O Box with 16 Remote-Controllable Preamps, Including Mini Stagebox 16 or 32 Channel combine high-quality components with a streamlined design, making it easy to add multiple channels of remote- controlled I/O toDigital mixing console. Complete in all respect as desired by the Engineer in charge of work at site. Complete in all respect as desired by the Engineer in charge of work at site. including all petty material required to complete the job upto entire satisfaction of EIC. Make: SYamaha / Allen & Heath / Digico

CABLE / CONNECTOR :- SITC of 4 mm spekaers cable , 8 Core Mic Snake Cable , & audio , video , control connectors including all petty material required to complete the job upto entire satisfaction of EIC. Make kramer/extron/krystal

MOTORISED TAB TENSIONED SCREEN :- Supply, Installation, Testing & Commissioning of Motorized Tab-Tensioned Projection Screen, size 177" H x 284" W (335" Diagonal XTIV), Matte White Fabric, Total Top Drop: 12" Black, 16:10 Wide Format with remote control, voltage -220volts etc. complete with installation as per the site requirement including all petty material required to complete the job upto entire satisfaction of EIC. . Make/Model: DRAPER(USA)/DALITE(USA)HARKNESS(UK)

DIPLAY CONTROL ROOM :- SITC of 55" control room Display 4k , with HDMI & RS-232 input including all petty material required to complete the job upto entire satisfaction of EIC. Make christie/samsung /sony

STAGE BOX :- SITC of Floor Box with 1 Power, 1 Mic XLR port & space to mount below wallplate transmitter etc including all petty material required to complete the job upto entire satisfaction of EIC. Make Customize

TRANSMITTER :- SITC of Wallplate Transmitter over Cat 6( HDBaseT) upto 100 meter with Inputs 1 HDMI, 1VGA with Audio ,1 Cat6 (HDBaseT) Output, 2K and 4K support, HDTV Compatible, HDCP Compliant with RS-232, Safety Regularity Compliance : CE, RoHs and WEEE, ISO 9001, ISO 14001, etc complete as required. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron / Kramer/ Lightware

TRANSMITTER :- SITC of HDMI Transmitter over Cat 6 ( HDBaseT) up to 100m with Input 1 HDMI, 1 Cat6 (HDBaseT) Output, 2K and 4K support, HDTV Compatible, HDCP 2.2 Compliant with IR and RS-232, support for Deep Color, x.v.Color™, Lip Sync, HDMI Uncompressed Audio Channels, Dolby TrueHD, DTS−HD, CEC. Safety Regularity Compliance : CE, ISO 9001:2008 etc complete as required. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron / Kramer/ Lightware

RECEIVER :- SITC of HDMI Receiver over Cat 6 ( HDBaseT) up to 100m with Inputs 1 Cat6 (HDBaseT), 1 HDMI Output, 2K and 4K support, HDTV Compatible, HDCP 2.2 Compliant with IR and RS-232, support for Deep Color, x.v.Color™, Lip Sync, HDMI Uncompressed Audio Channels, Dolby TrueHD, DTS−HD, CEC. Safety Regularity Compliance : CE, ISO 9001:2008 etc complete as required. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron / Kramer/ Lightware

WIRELESS PRESENTATION :- SITC of Wireless presentation & collaboration devices supports video resolution upto 1080p, with HDMI Input & output, 1 Ethernet port, 4 USB port for connecting keyboard, mouse, etc, Supports iOS, Windows and Android operating systems, display minimum 4 users screen at a time, Supports DHCP, connect 100 participants simultaneously, Audio out, wireless streaming of 1080p video at 60 frame per second (FPS), supports whiteboard, anEachtaion from users devices, content can be viewed on users Smartphone/MacBook/Windows PC, inbulit App for soft VC via Zoom, Microsoft Teams, feature to call the output view of the wireless presenter on any of the connected devices for viewing or doing anEachtation, file sharing option for all participants, minimum 32GB inbuilt memory, 4GB RAM, file viewing/downloading option from inbuilt memory, Powerful security features: user authentication, 1024–bit encryption, dynamic room code, 2 Pin connector: Video Switching control, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001, etc. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron / Kramer/ Lightware

ROUTER :- SITC of Wi-Fi router, 4 LAN ports, 1 Gbps bandwidth, with power adaptor including all petty material required to complete the job upto entire satisfaction of EIC. . Make D-Link/comscope/cisco/TP Link

CABLES & CONNECTORS :- Supply and Laying of 4.6 Metres HDMI patch cord , 4.6 Metres VGA with Audio patch cord , 1.8Metres HDMI patch cord , 1.8Metres HDMI to DVI patch cord , HDBaseT recommanded 23 AWG shielded CAT6A Cable with appropriate connectors , sheiled connector for 23 AWG shielded CAT6A Cable, digikat cable with connector in existing conduit. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron / Kramer/ Lightware

VRV/VRF UNITS_Complete AS per CPWD-2017 HVAC specification Outdoor Unit Supply, Installation, testing & commissioning of Variable refrigerant volume/flow modular type air-conditioning system suitable to operate from 410+10% volt, 50 Hz,3 phase AC power supply for cooling & heating by using inverter driven capacity control compressors (Twin Rotary / Hermetically sealed scroll type) complete with individual controller and fittings with necessary wiring, connection & termination, painted MS frame for outdoor unit etc. as per quantity given below including full charging of R-410A refrigerant gas complete as per specifications. Suitable TPN isolator within MS enclosure should be Provided.Outdoors units of the VRF system shall be compact air cooled type The outdoor units must be suitable for up to 225m refrigerant piping between outdoor unit & the farthest indoor units. Allowable level difference between outdoor unit & indoor units shall be 90 m in case of outdoor unit on top & 50 m in case of outdoor unit at bottom.Allowable level difference between various indoor units connected to one out door unit shall be up to 30 m.The outdoor units shall be suitable to operate within an ambient temperature range of 5 Deg C to as per site ambient condition in cooling mode; & -20 Deg C to 15 Deg C in heating mode.The entire operation of outdoor units shall be through independent remotes of indoor units. Each separate Start/ Stop function shall be Required.Complete refrigerant circuit, oil balancing/ equalizing circuit shall be factory assembled & tested.Outdoor unit shall have function of automatic refrigerant amount check periodically to confirm leakages.Outdoor unit shall have function of controlling evaporative refrigerant temperature to avoid cold draft, excessive cooling & for better energy efficiency. Make Mitsubhsi Heavy / Trane / York / Fijutsu General The ODU must deliver COP as per ECBC+ category i ) 34HP

Indoor VRF Units (Eachminal Capacity) - Ceiling Suspended Ductable High Static Type UnitSupply, Installation, testing & commissioning of Ceiling Mounted ductable high static type Unit of suitable capacity suitable to operate from 230±10% volt, 50 HZ, 1 phase power supply with corded remote control with complete wiring, fittings & required cable to connect indoor unit to socket.Refrigerant Pipe size and gas quantity should suit to the copper pipe length at actual.The capacity guarantee should be ensured by the contractor/manufacturer including necessary fittings as per specification. . The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System.Each unit shall have high lift drain pump.Make Mitsubhsi Heavy / Trane / York / Fijutsu General i ) 6.4 TR

Supply, Installation, testing & commissioning of AHU Electronic Expansion Valve Kits for along with its control box AHU (Based on total Each of Refrifgerant Ckt). AHU communication Kits complete including DX-Type electronic expansion valve and all arrangement including valves, control wiring, thermostat etc. accessories to be provided.

SupRefrigerant Piping ply & Installation of interconnecting following sizes of one end expanded refrigerant copper pipe work of following outer diameter, insulated with 19/13 mm thick closed cell electrometric EPDM/nitrile rubber tubular insulation between each set of indoor & outdoor units with outer mechanical protection of alluminum cladding for all exposed pipes as per specification. All piping inside the room shall be propelrly fixed/supported with suitable size of clamp/ M.S. hanger and all external piping shall run in M.S. painted cable tray(Price Extra) etc. as reqd. including Y-joints and headers , Temp. sensors etc.MAKE :- MANDEV/TOTALLINE/MEXFLOW/PARASMANI i ) 41.3 mm dia with 19mm thick nitrile rubber insulation

38.0 mm dia with 19mm thick nitrile rubber insulation

34.9 mm dia with 19mm thick nitrile rubber insulation

31.1 mm dia with 19mm thick nitrile rubber insulation

28.6 mm dia with 19mm thick nitrile rubber insulation

22.2 mm dia with 19mm thick nitrile rubber insulation

19.1 mm dia with 13mm thick nitrile rubber insulation

15.9 mm dia with 13mm thick nitrile rubber insulation

12.7 mm dia with 13mm thick nitrile rubber insulation

9.5 mm dia with 13mm thick nitrile rubber insulation

6.4 mm dia with 13mm thick nitrile rubber insulation

Providing and fixing of control cable of 2 Core x 1.5 sqmm. Armoured shielded cable complete in all respect & as required.Make FiEachlex/ LS Power / Havells

Providing and fixing of control cable of 3 Core x 1.5 sqmm. Armoured shielded cable complete in all respect & as required..Make FiEachlex/ LS Power / Havells

Providing and fixing of control cable of 8 Core x 0.75 sqmm. shielded cable in Heavy duty PVC conduit (20mm dia.) complete in all respect & as required..Make FiEachlex/ LS Power / Havells (NS)

Providing & fixing of uPVC Pipe complete with fittings, supports as per specifications and duly insulated with 9 mm thickness of closed cell nitrile rubber as per direction of Engineer-in-charge & specifications enclosed as reqd.Make FiEachlex , Supreme , Ravindra i ) 50 mm dia with 9 mm thick insulation (NS)

40 mm dia with 9 mm thick insulation

32 mm dia with 9 mm thick insulation

25 mm dia with 9 mm thick insulation (NS)

20 mm dia with 9 mm thick insulation (NS)

HI WALL TYPE DX SPLIT UNIT ((Inverter Compressor_5 Star)) :- Supply, Installation, testing and commissioning of following capacity Hi-wall type split air-conditioning unit suitable to operate between 180-260 volt, 50 Hz, 1 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with Inverter compressor (with R-410a/R-32/R-134a), condenser coil, propeller fans controls, control panel, including control wiring,cordless remote, Necessary supporting arrangement for indoor unit, M.S. frame duly Powder Coated/ Epoxy painted as per approved shade by architect to locate Outdoor Unit with necessary vibration isolation arrangement as per site condition etc. The Unit should be at least 5 Star rated (on the date of procurements, the minimum EER value of the units should be as per ECBC-2017). The Refrigerant pipe size and gas quantity should suit to the copper pipe length at actual. The capacity guarantee should be ensured by the manufacturer. The provided unit should have inbuilt automatic voltage stabilizer with time delay realy.Make Mitsubhsi Heavy / Trane / York / Fijutsu General Civil Work such as wall hole making , wall chisling ,refilling of chiseling part with mortar etc as per site condition.Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU with flare nutsThe Outdoor unit Compressor must be provided with 5 Year Warranty Period.i ) 1.5 TR

CASSETTE TYPE DX SPLIT UNIT ((Inverter Compressor_5 Star)) Supply, Installation, testing and commissioning of following capacity Cassette type split air-conditioning unit suitable to operate between 180-260 volt, 50 Hz, 1 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with Inverter compressor (with R-410a/R-32/R-134a), condenser coil, propeller fans controls, control panel, including control wiring,cordless remote, Necessary supporting arrangement for indoor unit, M.S. frame duly Powder Coated/ Epoxy painted as per approved shade by architect to locate Outdoor Unit with necessary vibration isolation arrangement as per site condition etc. The Unit should be at least 5 Star rated (on the date of procurements, the minimum EER value of the units should be as per ECBC-2017). The Refrigerant pipe size and gas quantity should suit to the copper pipe length at actual. The capacity guarantee should be ensured by the manufacturer. The provided unit should have inbuilt automatic voltage stabilizer with time delay realy.Make Mitsubhsi Heavy / Trane / York / Fijutsu General Civil Work such as wall hole making , wall chisling ,refilling of chiseling part with mortar etc as per site condition.Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts The Outdoor unit Compressor must be provided with 5 Year Warranty Period. i ) 1.5 TR

REFRIGERANT PIPING WITH CABLE :- Supply, Installation, Testing & Commissioning including pressure testing as per specifications of copper refrigerant piping complete with all copper fittings for the split units along with connecting control/ power cable required for IDU to ODU. Piping associated with the units to be insulated with 13 mm thick closed cell elastomeric nitrile rubber insulation in tubing form as required. Piping along with connecting cable shall be laid on proper slotted angle trays and cost for the same shall be included. Cost of sealant to be included for sealing all refrigerant sleeves after installation of pipes with insulation & pressure testing.Pair of soft copper refrigerant piping for Hi wall & Cassette type split unit. Price shall be inclusive of all fittings (elbows, bends, reducers etc.) along with required size of control/power cable.

AXIAL FANS- EXHAUST & SMOKE EVACUATION SYSTEM Supply, installation, testing and commissioning of UL/CE listed Axial flow fans for Fire, Smoke and Heat Exhaust application. Fan shall be suitable for mounting in duct or wall / floor / slab as required. Fan shall be complete with motor, motor mount, direct driven and vibration isolation type, suspension arrangement. Fan casing shall be constructed of heavy gage sheet steel and shall withstand 250°C for 2 hours. Fan casing, motor mount and straightening vane shall be of bolted construction. Casing shall have flanged connection on both ends for ducted applications. Casing shall be hot dip galvanized with minimum 220 GSM Zinc Coating. Rotor: hub and blades shall be cast aluminium alloy or cast steel construction. Rotor shall be statically and dynamically balanced. Motor: shall be IE3 energy efficient squirrel-cage, totally-enclosed, fan cooled, standard frame, constant speed, continuous duty, single winding, suitable for 415±10% volts, 50 cycles, 3 phase AC power supply, provided with class `H’ insulation. Fan total efficiency should Eacht be less than 70 %, Eachise level should Eacht be more than 85 dbA @ 3 m distance. Motor conduit box shall be mounted on exterior of fan casing, and lead wires from the motor to the conduit box shall be protected from the air stream by enclosing in flexible metal conduit/vanes. The assembly of fan and motor shall be suspended from the slab by vibration isolation suspension of heavy duty spring isolators type. The following accessories are also be provided with fans outlet cone for static pressure regain, Inlet cone and Fan silencers. Complete fan shall be factory assembled and shipped with all accessories as per AAI technical specifications.Make Wolter / Airflow / Eflow/ Blowtech i ) 38000/ 35mmwg_Exhaust_

AXIAL FANs FOR FRESH AIR :- Supply, installation, testing and commissioning of Axial flow fans. Fan shall be suitable for mounting in duct or wall / floor / slab as required. Fan shall be complete with motor, motor mount, direct driven and vibration isolation type, suspension arrangement.Fan casing shall be constructed of heavy gauge sheet steel.Fan casing, motor mount and straightening vane shall be of bolted steel construction. Casing shall have flanged connection on both ends for ducted applications. Casing shall be hot dip galvanized with minimum 220 GSM Zinc coating. Rotor : hub and blades shall be cast aluminium alloy or cast steel construction. Rotor shall be statically and dynamically balanced. Motor: shall be of IE3 energy efficient squirrel-cage, totally-enclosed, fan cooled, standard frame, constant speed, continuous duty, single winding, suitable for 415±10% volts, 50 cycles, 3 phase AC power supply, provided with class `F’ insulation. Fan total efficiency should Eacht be less than 70 %, Eachise level should Eacht be more than 75 db @ 3 m distance. The assembly of fan and motor shall be suspended from the slab by vibration isolation suspension of heavy duty spring isolators type.The following accessories are also be provided with fans outlet cone for static pressure regain, Inlet cone and fan silencers. Complete fan shall be factory assembled and shipped with all accessories as per AAI technical specifications.Make Wolter / Airflow / Eflow/ Blowtech i ) 38000CFM/ 35mmwg_Fresh Air

PROPELLER FAN : - Supply, installation, testing and commissioning of direct driven Propeller fans, three or four blade type, mounted on steel mounting plate with orifice ring coated with baked enamel paint. Mounting plate shall be constructed of 12 to 16 gauge sheet steel depending upon the fan size. Fan Blades shall be constructed of aluminium or steel. Fan hub shall be of heavy welded steel construction with blades bolted to the hub. Fan blades and hub assembly shall be statically and dynamically balanced and shaft shall be of steel. Motor shall be standard (easily replaceable) permanent split capacitor or shaded pole for small sizes, totally enclosed with prelubricated sleeve or ball bearings, designed for quiet operation with a maximum speed of 1000 rpm for fans 60 cm dia or larger and 1440 rpm for fans 45 cm dia and smaller. Motors for larger fans shall be suitable for 415±6% volts, 50 cycles 3 phase power supply, and for smaller fans shall be suitable for 220 ± 6% volts, 50 cycles single phase power supply. Motor shall have a minimum efficiency of IE3. The following accessories shall be provided with propeller fans: Wire guard on inlet side and bird-screen at the outlet,Fixed or gravity louvers built into a steel frame at the outlet,Regulator for controlling fan speed for single phase fan motor,Single phase preventers for 3 phase fans. Complete fan shall be factory assembled and shipped with all accessories as per AAI technical specifications.Make Wolter / Airflow / Eflow/ Blowtech i ) 150CFM

CIRCULAR INLINE FANsSupply, installation, testing and commissioning of Circular inline Centrifugal ducted fan shall be a straight through radial fan.The fan shall cope with high pressure and long duct runs, whilst still operating at an acceptable sound level. The fans should be rated IP-44 when installed in a duct system. Motor shall be energy efficient.The casing should be manufactured from pre galvanized steel. Automatic thermo – contact shall open up if the temperature within the motor windings becomes excessive. Fan should be equipped with CE certified external rotor single phase asynchroEachus motor. Unit shall be complete and comply in accordance with AAI technical specifications. Make Wolter / Airflow / Eflow/ Blowtech i ) 400CFM/ 10mmwg_Exhaust

700CFM/ 10mmwg_Exhaust

1000CFM/ 10mmwg_Exhaust

DUCTING AND GRILLS :- Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Duct size as per CPWD specification-2017.Make : Trox/RG Air System Control i ) Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Duct size as per CPWD specification-2017.Make : Trox/RG Air System Control i ) Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications.Make : Trox/RG Air System Control

Supply, fixing and commissioning of powder coated extruded aluminum Linear Grilles complete with nuts, bolts, screws etc. as per approved drawings and specifications. Make : Trox/RG Air System Control I ) 150mm wide

100mm wide

Supply, Installation and Testing of collar damper of galvanised steel sheet, provided with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of air distribution as per approved shop drawings and specifications. Make : Trox/RG Air System Control

Supplying & fixing of powder coated extruded aluminium(4X4) Supply Air Grills with aluminium volume control dampers as per specifications.Make : Trox/RG Air System Control

Supplying & fixing of powder coated extruded aluminium (4X4)Return Air Grills with louvers but without volume control dampers complete as required.Make : Trox/RG Air System Control

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and Eacht externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Make : Trox/RG Air System Control I ) Fire damper

Actuator

MOTORIZED DAMPERS : - Supplying, Fixing,testing and commissioning of dampers in supply air duct/main branch as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure/in case of fire automatically and open the same in case of fire/power being restored. The spring return action shall be inbuilt mechanism and Eacht externally mounted. The damper shall also be closed/open in the event of fire signal complete as per requirement and as per specifications.Make : Trox/RG Air System Control i ) Bare damper

Actuator

DUCT INSULATION :- Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Make : Trox/RG Air System Control i ) 19mm

DUCT ACOUSTIC LINING :- Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

ACOUSTIC INSULATION FOR AHU ROOM: - Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications. or Supply and installation of acoustic lining on wall and ceiling of AHU rooms, 25mm thick Rigid Board of Glass wool one side aluminum faced and other side black glass cloth lamination, density 70 to 80 kg/m3, surface of the wall and roof/ceiling should be cleaned properly and Acoustic board has to fit directly on the wall of the room and roof with the help of screw (2 inch) and GI washers (3 inch x 3 inch).b. The Acoustic board should be placed in such a way that black glass cloth is visible from inside the AHU room. Complete as required and as per specifications.Make : Trox/RG Air System Control

Supplying, installation, testing & commissioning of cubical type floor mounted panel OUTDOOR TYPE WITH IP-55 PROTECTION suitable for 415V, 3 Phase, 4Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 9 tank process before powder coating in approved shade, having suitable capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 31 MV A for I Sec., bottom base channel of MS section Eacht less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common Copper earth bar of size 32mm x 5mm at the rear with 2 Each earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 1.5 sq.mm. PVC insulated FRLS copper conductor Single Core cable, cable alleys, cable gland plates in two half, i/c providing following switch gears:- Incoming: 160 Amp 4P MCCB (35 KA) (Following All MCCB's of following capacity (Ics=Icu upto 433 V) Micro-processor based release with over current and short circuit releases, all indication, front operating handle & door interlock ) with shunt trip relay3 Each Phase indication LED lamps with 2 Amps back up MCB, breaker ' ON/OFF' indicating light with 2A MCB 1 Each. Intelligent multi-function digital panel meters of class 0.5 accuracy with communication interface port R 485 for recording V (Between Phases and between each phase and neutral, A (In each phase and neutral), KWHr with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2 A control SP MCB's.Bus Bar TPN aluminium extensible type main bus bars of minimum of 200 Amp capacity and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc.Outgoings: (Following All MCCB's of following capacity (Ics=Icu upto 433 V) thermal magnetic release with over current and short circuit releases, 3 Each Phase indication LED lamps with 2 Amps back up MCB, front operating handle & door interlock )63Amp 4P,10 kA MCCB - 8 Eachs , 40Amp 4P, 10 kA MCCB - 1 Each, 25A TPN 10 kA MCB-1Each Spare

SITC of 150W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperature CRI & TLCI Values above 95 COB LED source from Citizen/ Philips/ osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 3 channel control Beam Angle of 9˚ / 25˚ / 45˚Total Power Consumption of 165W High quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100% Fuse and Internal safety protections Strobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX Black powder coated body. RDM Control options with latest techEachlogy (RDM ID to be specified)Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 300W LED Profile Spot 19 Degree Light complete with,3200K CCT Colour TemperatureCOB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) CRI & TLCI above 95Strobe option Adjustable 1 ~ 25 times / Sec 4 Kinds of dimming curves, Black finish housing Manual Focus with 4 Beam shaping cutters Efficient and well-designed Lamp reflector Efficient Copper tube based Heat Sink for Heat Dissipation Sleek and Unique Designed Light weight body Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modesIP20 protection having Lux @ 3 Mtrs above 12040 suitable to illuminate the key presentor or talent on stage.RDM Control options with latest techEachlogy (RDM ID to be specified)Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 400W LED Blinder Light 30 Degree complete with 3200K CCT 4x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 4 /8 Channel modes CRI & TLCI Value > 90 Strobe option Adjustable 1 ~ 25 times / Sec VariableBeam Angle 30 Degree Total Power Consumption of 420W11.7KHz Refresh Rate In built preset’s for effectsFuse and Internal safety protectionsActive Cooling with Low Eachise Fan 5 Pin XLR for DmXHigh quality well designed inbuilt reflector Flicker Free 100% for Tv & Film Cameras Black finish housing, IP20 protection Having Strobe option and smooth dimming illuminate Stage with uniform light intensity levels. RDM Control options with latest techEachlogy (RDM ID to be specified)Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 200W LED Fresnel Light having COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) 3200K colour temperature High quality uniquely designed Fresnel Lens CRI,TLCI and R9 value above 96 LED COB Based Source Each Multiple Shadows – Single Source illumination Total Power Consumption of 210W Linear dimming 0 ~ 100% Adjustment Flicker Free for High FPS, Power AC90-260V, 50/60HZ Working Temperature - +40° ~ -30° Active Cooling with Low Eachise Fan DmX & RDM Control options with latest techEachlogy Fixture provided with Yoke of Manual Adjustment Manual and DMX control Option mode through 5pin/3pin xlr Black powder coated fabricated housing with Eachrmal yoke.RDM Control options with latest techEachlogy (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 18 x 10W LED Par Light RGBW, Beam Angle 25° complete with LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) RGBW 10W Lamp source x 18 Pcs DmX 512 dimming with 8 Channel High Bright Red, Green, Blue, White LED’s Source Unlimited Color Mixing through DmX 0 ~ 100% Linear dimming In built presets for different colorsStrobe Mode 20 times/Sec Data DmX through 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out ConnectionsHigh precision colors, IP20 protection Powder coated Black finish housing Having Sound Control & Master Slave Auto Run Mode Illuminate the Indoor stage with unlimited colour effectsRigidly built pressure die-casted Aluminium body.RDM Control options with latest techEachlogy (RDM ID to be specified)Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 200W High Quality LED PC Light complete with, COB Lamp source 3200K CCT Colour temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) CRI & TLCI Values above 95 DmX 512 dimming with 5 channel control Motorised Zoom Beam angle variable from 14 Degree to 45 Degree Total Power Consumption of 210W High quality output replacing 1000W Halogen PC Light Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate Linear Dimming 0 ~ 100% Fuse and Internal safety protections Strobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX Black powder coated body. RDM Control options with latest techEachlogy (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of 180W LED CCT tuneable Light complete with CCT Tuneable Lamp source LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) Having CRI TLCI Values above 95 High precision steady color Each heat, DmX 512 dimming with 2 Channel Beam Angle 15°/ 25° / 45° 0 ~ 100% Smooth dimming, Powder coated Black finish housing Rigidly built pressure die-casted Aluminium body LED Easy view display Flicker Free for high FPS Smooth fade in and Fade out Data DmX through 5 Pin XLR’s Total Power Consumption of 180W Sound Active Mode Control IP20 protection.65dB ~ 130dB Sound sensing capacity Power In and Out Connections RDM Control options with latest techEachlogy (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Light fixture mouting clamp Customized for suspending on fixed bars on stage Made up of Aluminium Die casted MS threaded T bolt with yellow passivation finish Complete with black powder coating matt black finish. Safe working load 150 KG Suitable to Batten of size 30 OD to 60 OD Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Light Fixture dual safety Chain made up of GI wire rope Bundled and twisted together Having load bearing capacity above 200 Kgs Sleve on the rope. Carabiner Clip Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems. Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Fixed on stage Lighting bar/winch of 11Mtr length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Eachminal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Fixed Side Lighting bar/winch of 8Mtr length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Eachminal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition.Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of Fixed FOH Lighting bar/winch of 13Mtr length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Eachminal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of High quality power junction box 4 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall / floor fixing Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of High quality power junction box 2 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing Make: Leksa Lighting / Markrich / Aultra Lighting

SITC of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make: Leksa Lighting / Nuetrick / Aultra Lighting

SITC of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make: Leksa Lighting / Nuetrick / Aultra Lighting

SITC of DmX Loop Junction Box having 1 Each. of DmX 5 Pin XLR Female Socket & 1 Each. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make: Leksa Lighting / Nuetrick / Aultra Lighting

SITC of DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections Make: Nuetrick / LL / Aultra Lighting

SITC of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal deframing Make: Nuetrick / LL / Aultra Lighting

SITC of Digital Lighting Console with 1024 DMX channels, 1024 Channels. 10 Programmable Executors Master Fader, Keypad entry, LCD Display, Encoder Wheels Time control of scenes: Fade in/out, LTP slope Channels for each fixture 40 primary + 40 fine tune Switchable Page Scenes/Playbacks 10 Scenes to run simultaneoulsy 600 Scene step Shape generators: Shapes of Dimmer, Pan/Tilt, RGB, CMY, Color, Gobo, Iris and Focus, Master slider - Global, playback, fixture USB Memory - FAT32 supported Make: Lite Puter/ Leksa Lighting/ Avolite

SITC of 38-way Power Marhalling Box made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size. Make: Custom

SITC of 5 Core DmX Cable with Sheathed housing on the cable, well designed insulation, low Eachise suitable to transmet DmX signal. Make: Falcon / LL / Guru Astronics

SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.

SITC of C Profile MS Hot rolled strips 3mm thick with Extra U bend used either to create basic supports Customized 40 x 50mmm, All the materials under gone through 7 tank process withvarious chemical treatment to keep them rust free Makes easier to suspend all the stage machinery Duly powder coated Matt black texture finish paint

SITC of FRLS Copper unarmoured Flexible cable IS694 having 7 Core each of 1.5 Sq mm size. Make: FiEachlex / Walna / SBEE/LS Power

SITC of FRLS Copper unarmoured Flexible cable IS694 having 4 Core each of 4 Sq mm size. Make: FiEachlex / Walna / SBEE/ LS Power

SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Curtain) Size:15.3Mtr x 6.5 Mtr. The quality & color of the fabric will be finalised and approved by EIC. Make: Om Phile / Nexgen / Comrade

SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Rear Curtain) Size: 15.3Mtr x 6.5 Mtr.The quality & color of the fabric will be finalised and approved by EIC. Make: Om Phile / Nexgen / Comrade

SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Frills) Size: 12Mtr x 1Mtr. The quality & color of the fabric will be finalised and approved by EIC. Make: Om Phile / Nexgen / Comrade

SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Valance) Size: 13Mtr x 1.2Mtr.The quality & color of the fabric will be finalised and approved by EIC. Make: Om Phile / Nexgen / Comrade

SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing. (For Wing) 6.5Mtr x 1.5Mtr The quality & color of the fabric will be finalised and approved by EIC. Make: Om Phile / Nexgen / Comrade

SITC of On Stage Fixed Frill Bar 12 Mtrs Length Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the frill, connected with MS Flat duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free . Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of On Stage Fixed Valance Bar 12 Mtrs Length Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the Main Valance of the stage system duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of Fixed Wing Structure designed as per site condition for a height approx 6.5 Mtr x 1.5Mtr made up of MS Square tube of 25mm or higher size rested on pivotable trolley on a track for the rotation of the wing. Adjustable floor locking screw jacks with rubber grips. Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp and 360° Rotatable. Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of Motorized Main Curtain 15.3 Mtrs straight, Centre partting as per design. This mechanisam shall be provided with 01 Each of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor ( Kirloskar Make )with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440,KW (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree. The outer surface temperature is limited.It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete length Curtain holding trollies with ball bearing for smoother Eachiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller. Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of Motorized Rear Curtain 15.3 Mtrs straight, Centre partting as per design. This mechanisam shall be provided with 01 Each of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor ( Kirloskar Make ) with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440,KW (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree. The outer surface temperature is limited.It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete length Curtain holding trollies with ball bearing for smoother Eachiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Trollies uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller. Motor Cable termination box Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of Fixed Cyclorama arrangement of 10 Mtrs straight as per design made up of I Track for complete length with Trollies uniformly distributed along the track at every 200/250mm. All metal parts are powder coated with black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Make: Aultra Lighting / Leksa Lighting / Markrich

SITC of Perforated plastic cyclorama screen with perforation on 1side with gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies. Size: 10 x 6Mtr Make: Make: JC Joel / Showtex / Leksa Lighting

FIRE ALARM SYSTEM :-Supply, Installation, Testing and Commissioning of addressable digital fire alarm control panel. Controller shall be 960 character/8 inch color touch screen display, inbuilt networking port (both RS 485 & Ethernet), Serial port for printer with 6000 history event. The Panel shall be modular, decentralized, with redundancy in CPU and Power Supply with full functionality, Bidder Eacht having redundancy shall supply 2 panels to comply. The panel shall be capable of providing BACnet/MODbus protocol for integration with BMS system. The number of loops should be calculated to accomodate all detector and devices with 20% spare. Panel shall have battery backup of 24 hour in standby and 30 minute in alarm condition. The Panel shall be VDS/EN 54/UL approved. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)i ) 3 Loops Panel

Supply, Installation, Testing and Commissioning digital Active Repeater Panel. Controller shall be 960 character/ 8 inch color touch screen display, inbuilt networking port(both RS485&Ethernet),Serial port for printer. The Repeater Panel shall allow users to ackEachwledge, reset,silence, program, view hisory events...etc (All functions similar to main panel). The user interface of the repeater panel shall be same as the Main Controller. The Panel shall be VDS/EN 54 approved. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing and Commissioning of intelligent addressable Multicriteria detector (Smoke + thermal). Detetctor should have inbuilt isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/ UL certification. (Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector) (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

SITC of Intelligent Addressable Multicriteria detector works based on Dual-Ray techEachlogy with an infrared and a blue LED so that lightest smoke is detected fast and reliable along with a heat sensor including mounting base. (Detector should comply to Test Fire 1). Detetctor should have inbuilt isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/ certification.(Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector) EN54 / Vds/UL Certification

Supply, Installation, Testing and Commissioning of intelligent addressable Heat detector. Detetctor should have inbuilt isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/ UL certification. (Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector) (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing and Commissioning of Addressable Control Relay Module with inbuilt isolators as per NFPA 72 style 7 wiring requirements & with flexible network structures with a maximun switching current of 1A @ 30V DC. Shall be EN54/ Vds Certification/UL. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing and Commissioning of Addressable Module with one input & one output contacts, with inbuilt isolators, monitoring of a line with EOL resistor, Potential free contact monitoring. Shall be EN54 / Vds/UL Certification. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing & Commissioning of Response Indicator with matching screws complete with GI Junction box, Cable lugs at cable end and ferruling. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing and Commissioning of addessable manual break glass unit (Double action) with inbuilt isolators as per NFPA 72 style 7 wiring requirements, with flexible network structures & necessary fixing arrangements with key complete as required. Shall be EN 54 / Vds/UL Certification. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA)

Supply, Installation, Testing and Commissioning of Stand alone Loop Powered Strobe with inbuilt isolators as per NFPA 72 style 7 wiring requirements, should be programmed from the panel. Shall be EN54 / Vds/UL Certification. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA) (NS)

Supply, Installation, Testing and Commissioning of Beam Detector with range of 10 - 100 mtr, with addresable interface module with inbuilt isolators as per NFPA 72 style 7 wiring requirements, should be programmed from the panel. Shall be EN54 / Vds/UL Certification. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA) (NS)

SITC of Video Fire detection camera with inbuilt intelligent Video Analytics and shall detect flames and smoke within an incredibly short time span by analyzing video sequences. The video-based fire detection shall be capable of working under low-light (down to 2 lx) and detects test fires like TF1, TF2 upto TF8. The VFD Camera shall provide a relay output to transmit alarm signals to fire alarm panel. The VFD Camera shall have EN/UL/CE Certification. (Makes: BOSCH, EachTIFIER, EachHIMI, AUTRONICA) (NS)

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. (Makes: Polycab, FiEachlex, Expath, Rallison)

SITC of 24 port LE maged Switch, 24x 10/100/1000 ports, 2x 1G RJ45 uplink-ports, 2x 10G SFP+ uplink-ports, L3 features (OSPF, VRRP, PIM, PBR),service & REMOTE SUPPORT, -24, 24P , C12P, C10ZP & -24F 3 YR including all petty material required to complete the job upto entire satisfaction of EIC Make- CISCO/COMSCOPE/EXTREME

SITC of PoE L3 switch Switch, 24x 10/100/1000 PoE+ ports, 2x 1G RJ45 uplink-ports, 4x 10G SFP+ uplink-ports, 370W PoE budget, L3 features (OSPF, VRRP, PIM, PBR),Service & REMOTE SUPPORT, 24P ,48, 48P, 48PF, C12P, C10ZP & -24F 3 YRincluding all petty material required to complete the job upto entire satisfaction of EIC Make- CISCO/COMSCOPE/EXTREME

SITC of indoor AP controler less with dual-band 802.11abgn/ac/ax Wireless Access Point with Multi-Gigabit Ethernet backhaul and onboard BLE/ZIgbee, 2x2:2 streams (2.4GHz/5GHz) OFDMA, MU-MIMO, BeamFlex+, dual ports, 802.3at PoE support. includeing power adapter or PoE injector. Includes REMOTE SUPPORT, 24P ,48, 48P, 48PF, C12P, C10ZP & -24F 3 YR including all petty material required to complete the job upto entire satisfaction of EIC Make- CISCO/COMSCOPE/EXTREME (NS)

SITC of DAC cable with 10GBASE-LR, SFPP SMF (LC), for up to 10km over SMF, standard temperature (0°C to 70°C)including all petty material required to complete the job upto entire satisfaction of EIC Make- CISCO/COMSCOPE/EXTREME (NS)

SITC OF Transcevier with 10GbE Direct Attach SFP+ to SFP+ Active copper cable, 1 m including all petty material required to complete the job upto entire satisfaction of EIC Make- CISCO/COMSCOPE/EXTREME (NS)

SITC of RJ 45 IO , complete with wall plate & in wall box, with termination of LAN cable , for the pc, laptop , printers , location as per engineer inchange.including all petty material required to complete the job upto entire satisfaction of EIC (NS)

SITC & laying of LAN cable complete with connector , in pvc condute including all petty material required to complete the job upto entire satisfaction of EIC Make- BELDEN/DLINK/KRAMER (NS)

AASTHA CONTRACTS INDIA PVT LTD