REPAIRS/MAINT OF JOINERY AND CONNECTED WORKS TECH, REPAIRS/MAINT OF PLINTHS INCL ATT AND ALLIED WORKS AT TECH AREA, REPAIR/MAINT INCL REPLACEMENT OF DAMAGED SHEETS/GI ROOF SHEETS AT TECH AREA, REPAIR/MAINT INCL REPLACEMENT OF DAMAGED FLOOR AND WALL T

Amount

Taking down cement plaster on brick or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed..

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Dismantling of floor, hearth or wall tiles including cement mortar bedding ( but not backing) and remvoing rubbish off the premishes, complete all as specified and directed.

M & L for brick work with sub class 'B' bricks, old size bricks, straight or curved on plan exc 6m mean radius built in CM (1:6), complete all as specified and directed.

All as per item No. 4.00 here-in-before but except bricks, complete all as specified and directed. Note-(i) Brick shall be obtained from demolition shall be re-used. (ii) The quoted rate shall deemed to be included for cleaning of old bricks obtained from demolition.

M&L 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with water proofing compound top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

Supply only liquid water proofing compound, complete all as specified and directed.

M&L 5mm thick rendering in CM (1:3) on ceiling surfaces, finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of acrylic distemper (1st grade quality) of approved shade and colour over a coat of primer over and including 2mm thick acrylic wall care putty, complete all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying three coat of white washing, complete all as specified and directed.

M&L for preparation new plastered surfaces of wall and applying two coated of 100% premium acrylic exterior emulsion paint alkali & fungal resistance of required shade including primming coat of exterior mulsion primer as per manufacturer's instructions, complete all as specified and directed.

M&L for complete removal of the existing old treatment on walls and applying two coats of acrylic distemper over and including 2mm thick acrylic wall care putty, complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one (camouflage pattern) and finishing wall with acrylic smooth exterior paint of required shade as per manufacturer's specification, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm/450x350 x7mm thick each as in skirting or dado on vertical surfaces of wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

M&L for coloured non skid ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for coloured non skid ceramic tiles 10mm thick (square/rectangular) polished, vertical surface skirting/dado, area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement pigment to match laid over and including 10mm thick screed bed in CM (1:6), complete all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc. 1 Sqm but n.exc 2 Sqm each, complete all as specified and directed.

S&F 2nd class hardwood plain,solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

M&L 35mm thick 2nd class hardwood factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particale board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 30mm thick factory made 2nd class hardwood glazed and skelton door shutters of open rebated and prepared to receive glass edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawings, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width or aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width or aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth not otherwise described over a coat of pink primer and applying one coat of synthetic enamel paint (1st grade quality) over a coat of pink primer, complete all as specified and directed.

Hacking out old broken glass of any thickness, size, quality or description from wooden frames including punching or drilling our old glazing pins/spring clips, complete all as specified and directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

S&F for glazed powder coated coloured minimum 15 micron aluminium sliding windows shutter with frame of size 101.60mm x 44.6mm x 2.4mm thich push/pull type glazed door shutter having top and bottom section 83 x 44.5 x 2.4 mm and 100 x 44.5 x 2.4mm thick respectively, styles section 80 x 44.5 x 2.4mm thick and lock rail of size 00 x 44.5 x 2.4mm thick including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size including 5mm thick tinted sheet glass in both panel, hings, mortice lock, stays & aluminium anodised handle of suitable size etc., complete all as specified and directed.

S & F 150mm long, aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300 long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

S & F 100mm size, butt hinges, medium weight, cold rolled, mild steel, complete all as specified and directed.

S & F 75mm long, butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type E-22 complete all as specified and directed.

S & F aluminium handles, cast type, anodised, 150 mm size, complete all as specified and directed.

S & F in repairs, aluminium (die cast) body door closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg, complete all as specified and directed.

S&F mild steel hold fast made out of MS flat iron for chowkaths and other small articles including making shape, drilling hole etc, complete all as specified and directed.

M&L for PCC type B1 (1:2:4) (using 20mm graded stone aggregate) as in hold fast block including necessary form work, complete all as specified and directed.

Taking up or down 15mm bore GI tubing of and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore GI tubing of and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and laying CPVC pipe of size 16mm dia high pressure CPVC pipes SDR-13.5 & plain CPVC, SDR 11, fittings complete laying in trenches/ wall/floor/roof terece with necessary saddle/clamps including all necessay fittings, like elbow, tee, socket, reducer, bushings, end caps, end plugs, etc and with CPVC solvents cement, complete all as specified and directed.

Supply and laying CPVC pipe of size 20mm dia high pressure CPVC pipes SDR-13.5 & plain CPVC, SDR 11, fittings complete laying in trenches/ wall/floor/roof terece with necessary saddle/clamps including all necessay fittings, like elbow, tee, socket, reducer, bushings, end caps, end plugs, etc and with CPVC solvents cement, complete all as specified and directed.

M&L for cutting chases on wall surface, pinning in, making good to facings where required and pointing in CM (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10cm girth, complete all as specified and directed.

S&F in repairs bib tap 15mm bore, chromium plated, two way, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets, complete all as specified and directed.

S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends, complete all as specified and directed.

S&F in repair fancy type 15mm bore chromium plated bib tap, cast copper alloy, with crutch or butterfly handle, screwed dpwn, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair fancy type 15mm bore chromium plated stop valves with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed fency type, complete all as specified and directed.

S&F in repair fancy type 15mm bore cast copper alloy chromium plated health faucet with flexible PVC pipe for EWC, complete all as specified and directed.

S & F in repairs, cast iron nahani trap 100mm dia with grating including jointing to waste pipe fixed in CM (1:2:4) type B2 (using 20mm graded crushed stone aggregate), complete all as specified and as directed.

S & F in repair 110mm bore, PVC (SWR), soil waste and vent pipes in any length with or without ears, with cement joints fixed to wall, etc with all necessary fixing arrangement, complete all as specified and directed.

S&F in repair of 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based corrugated steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based plain steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F 2mm thick fibre glass reinforced translucent plane/corrugated sheeting with two corrugations side lap fixed with coach screw and washer as in roof wall etc, complete all as specified and directed.

S&F roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel ,rolled section or flat sections) of Fe-290, E-265 including distance pieces, cleats etc, complete all as specified and directed.

M&L for prepartion of new steel surfaces of any description over 10cm width or girth not otherwise described and applying of two coats of synthetic enemel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 75mm thick PCC type C2 (1:3:6) (using 40mm graded crushed stone aggregate) as in plinth protection, sub base etc. finished even and fair without using extra cement etc, complete all as specified and directed.

M&L for 40mm thick PCC type B1(1:2:4) (using 20mm graded crushed stone aggregate) as in path etc finished even and fair without using extra cement etc, complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x20cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors complete all as specified and directed.

M&L for providing chemical emulsion for post construction anti-termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.

M&L for earthing of equipment complete with copper earth plate electrode 60 x 60cm.× 3.15mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:2:6) type C-1 with suitable size of CI cover plate with angle iron frame and opening arrangement ) incl providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect,including copper earth strip 20 x 3.15mm, 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of soil to a distance not exc 50 mtr and necessary testing on completion including taking down/dismantling of old unserviceable earthing of any description, complete all as specified and directed. Note : (i) Earth result after installation completely should be less than 5 Ohm. (ii) Copper earth strip beyond 7.5m shall be measured and paid separately under appropriate item.

M&L for earthing of machinery/equipment installed at power house/Sub Stn/ DB complete with steel earth plate electrode 60 × 60cm × 6mm thick , buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:2:6) type C-1 with suitable size of CI cover plate with angle iron frame and opening arrangement ) incl providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect,including galvanised earth lead wire 4.0mm, 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc 50 mtr and necessary testing on completion including taking down/dismantling of old unserviceable earthing of any description, complete all as specified and as directed. Note : Earth lead strip/wire beyond 7.5 mtr shall be measured and paid separately under appropriate item.

M&L for earthing of machinery/equipment installed at power house/Sub Stn/ DB complete with steel earth plate electrode 60 × 60cm × 6mm thick , buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:2:6) type C-1 with suitable size of CI cover plate with angle iron frame and opening arrangement ) incl providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect, including galvanised iron earth strip 32 x 6mm, 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc 50 mtr and necessary testing on completion including taking down/dismantling of old unserviceable earthing of any description, complete all as specified and as directed. Note : (i) Proper earthing pit should be provided with pit cover. (ii) GI earth strip upto 7.5m is demed included in the unit rate.

S&F 32 x 6mm GI earth strip in short pieces on surface or in recess for all interconnecting, in and including taking out worn out and damaged earth strip/wire, complete all as specified and directed.

All as per item No 72.00 here-in- before but copper earth strip 20 x 3.15mm, complete all as specified and directed.

All as per item No 72.00 here-in- before but copper earth strip 32 x 6mm, complete all as specified and directed.

All as per item No 72.00 here-in- before but galvanised iron earth wire 4mm dia, complete all as specified and directed.

S&F HDPE pipes 40mm bore of pressure rating 6 kgf/cm2 laid in trenches/walls and ceilings by MS iron clamp nuts bolts etc, with all fitting and fixed, complete all as specified and directed. Note : Unit quoted rate shall deemed to be inclusive of earth work, cutting chases to walls/ceiling/floor etc.

All as per item No 76.00 here-in- before but 15mm bore, complete all as specified and directed.

M & L for construction of earthing pit in PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate), pre-cast RCC cover slab of size 300 x 300 x 50mm with one handle made out of 8mm dia round bar, 20mm dia GI pipe of light grade for watering funnels, wire mesh three coats of white wash on plastered surfaces (exposed surfaces) including taking down existing broken earth pit, complete all as specified and directed. Note : Unit quoted shall deemed to be inclusive of necessary earth work.

S&F porcelain vitreous white/brown/green spacers insulator of size 75mm x 35mm x 40mm height complete with one number galvanized iron stud bolts 6mm dia x 40mm long including nut & washers and two number galvanized iron fixing bolts of size 6mm dia and 50mm long including washers and drilling holes for holding/foxomg aluminium strip/roof conductor as required, complete all as specified and directed.

M & L for test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hex. head screw, complete all as specified and directed.

M & L for brazing of copper strip including removing of nut, bolt, washer, etc and connecting with equipment directly from earthing, complete all as specified and directed.

Note: An amount of Rs.62,664.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

BHARAT ELECTRIC

M/S BISHAL ENTERPRISES

M/S. NARENDRA KUMAR GARG

M/S SARDAR MAL NAHATA

M/S ROY ENTERPRISE