PROVN OF 01 X RECEPTION EX-SERVICEMEN CELL WITH TOILET FACILITY, 01 X STORAGE SHED NEAR BLDG NO. P-61 AND VISITORS ROOM AT ARTY CENTRE UNDER GE NRC.

Amount

Surface dressing n. exc 15 cm deep, getting out in hard/dense soil.

Site clearance in soft/loose soil all as per directed by Engr in Charge

Excavation in trenches, n. exc.1.5m wide and n.exc. 1.5m deep for foundation n.exc.10 Sqm on plan and getting out hard/dense soil complete all as specified and as directed.

Excavating in trenches n.exc 1.5 m wide & n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc, n. exc 10 Sqm on plan and n. exc 1.50m in depth and getting out in any type of soil.

Removing excavated material n. exc. 50 m and depositing where directed 50 m and upto a total distance of 250 m.

M&L for Cement concrete type D2(1:4:8) using 40mm graded stone aggregates as in foundation lean concrete complete all as specified and as directed.

M&L for PCC(1:3:6) type D-1, using 40 mm graded stone aggregate Cement concrete in foundations, filling and mass concrete

S&F pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated of approved profile steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specfied and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240

S&F rolled MS framed work as in door or gate, angle or other sections with gusset plastes, rails barces complete drilled for fixing steel sheeting or other covering in door including nut and bolts required prepared for hanging with steel hanging doors fitting and hanging or exsiting pintels also fastering and fixing complete all as specified and as directed.

S&F 1.6 mm thick MS sheet plain black steel door and similar work cut to size, holes, punched including round headed screws with plain 40mm lap joints with riveted or welded seams including bending or turning up mitred angles etc as requried all as directed.

M&L for brick work fly ash brick with old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work fly ash brick with old size brick straight or curved on plan to any radius in half brick thick walls, built in 1:4 complete all as specified and as directed.

M&L for Rendering for 10mm thick with CM 1:6 on fair faces of brick work to be finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick masonary or concrete surfaces in cm 1:4 finished even and smooth without using extra cement for external surface of wall complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M&L for 05 mm thick rendering in CM 1:4 on concrete surface as in ceiling surface finished even and smooth without using extra cement.

M&L for rendering 5 mm thick (1: 3) on fair faces of concrete surfacesof ceilings finished even and smooth without using extra cement. complete all as specified and directed.

M&L for rendering 15 mm thick (1: 6) on fair faces of brick work or concrete surfaces finished with sagol finish not exceeding 1.5 mm thick.

M&L for rendering 10mm thick cement plaster 1:4 on fair faces of brick work or concrete surfaces as a backing coats for fixing tiles.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n. exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hardcore of gauge n.exc 63mm deposited, spread in layers n.exc 15 cm thick,watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in sub base floor finised etc complete all as specified and as directed.

M&L for cement concrete Type D2 1:4:8 (40 mm graded aggregate) 75 mm thick as in sub base

S&F 3mm thick sheet glass,ordinary quality and glazing with oil putty squares not exc 0.5 Sqm in each pane complete all as specified and as directed.

M&L for painting with two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces exc 10cm width or girth including preparation of new steel surfacesall as specified and directed by EIC.

M&L for mild steel TMT bars 10mm dia and over cut to length bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (anneled) not less than 0.9mm dia or securing with clips quality coinforming to IS complete all as specified and as directed.

M&L for TMT bars 6 to 8mm mm dia and over cut to length bend to shape required including cranking, bending, and binding with mild steel wire (annealed) not less than 0.9 mm dia.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirupps,spacers and binders complete all as specified and as directed.

M&L for two coats of oil bound distemper on chalk whitning primer with 3mm thick wall care putty concrete /brick surfaces including preparation of surface complete all as specified and as directed.

M&L for preparing plastered surfaces and applying two coats of oil bound distemper over one coat of primer including preparatory work with including and applying wall care putty to distempering on surfaces of walls.

M&L for three coat of white wash including preparation of new surfaces on ceilling complete all as specified and directed.

M&L for two coats of cement base paint over newly plaster/concrete surfaces of wall any description of plastered surface including priming coat complete all as specified and as directed as per manufactures instructions.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregates as in bed block provided for hold fast or at similar work complete all as specified and as directed.

M&L for reinforced cement concrete of M-25(Design Mix) 20 mm graded aggregate as in footings,foundation beams and plinth beams

ditto as Item No. 38.00 above but as in columns

ditto as Item No. 38.00 above but as in beams and lintel beams

ditto as Item No. 38.00 above but as in slabs supported on walls & roof beams

ditto as Item No. 38.00 above but as in Chajja

Use and waste formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick (horizontal or slopeing) with rough finished surfaces complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs also splays between floors and beams complete all as specified and as directed.

M&L for formwork to sides of soffits of floor or roof beams,cantilevers,lintels etc for flat rough finished surfaces of concrete

Use and waste formwork to side of concrete foundation,plinth beams,base of column,side of column for rough finishes surfaces of concrete complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finishes surfaces of concrete complete all as specified and as directed.

Use and waste of form work to edges of concrete flat horizontal or sloping and similar woprk exc 10 cm but n. exc 20 cm wide for rough finished surfaces complete all as specified and as directed.

Use and waste formwork to side of concret Formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal shape for rough finishes surfaces of concrete complete all as specified and as directed.

S&F Machine cut kota stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specifed and directed

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with gray cement slurry with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Screed bed or bedding layer of cement mortar 20 mm thick for laying floors finishes in cement mortar 1:6 complete all as specifed and directed

M&L for Screed bed or bedding layer of cement mortar 15 mm thick for laying floors finishes in cement mortar 1:6.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors over 15mm thick cement screed bed in cm 1:6 set and jointed in neet cement slurry and pointed in coloured cement to match the surface complete all as specified and as directed.

M&L for glazed coloured ceramic tiles 450x300x7mm thick as in verticle surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 cm thick plaster in cm 1:4 complete all as specified and as directed.

M&L for Vetrified Ceramic coloured light grade tiles 10mm thick (Squre/rectangular) ploshed, area of each tiles not exeeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade

Ditto all as per item No. 56.00 above but in skirting, steps, etc in vertical surfaces.

S&F Solid PVC frame of size 50mm x 95mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, with necessary arragement for fixing of glass for louvers type window/ventilator and additional PVC beading around the frame for fixing of wiremesh, S&F in opening all as specified and directed by Engr-in-Charge

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, in opening as per specification and drawing complete all as specified and as directed.

S&F factory Made Solid PVC Moulder Door Shutter, with particle Board Core 28 to 30 mm thick (stiles), with 2,4,or 6 raised planel design with 2 mm thick Moulder PVC Sheet on the front face & 2 mm Plain colour PVC sheet on back face, suppplying & fixing in frame at site as per specification and drawing.

S&F 35 mm thick Second class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed

S&F IInd class hard wood factory made Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats complete all as specified and directed

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints

M&L for painting with two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces exc 10cm width or girth including preparation of wooden surfaces all as specified and directed by EIC.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specified and as directed.

S&F 150mm aluminium anodised barrel tower bolts of extrubed section complete all as specified and as directed.

S&F extruded 125mm aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections complete all as spectfied and as directed.

S&F rotational moulded three layers polyethylene water storage tank capacity 1000 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F 20mm bore ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

S&F 20mm bore Gun-metal gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

M&L for 20mm bore of pipe cutting existing steel tubing for alterations or addtions (Each cut measured) all as specified and as directed.

S&F of 15mm bore steel tube medium grade galvanised, with all fittingS&Fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

S&F of 20mm bore steel tube medium grade galvanised, with all fittingS&Fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

S&F bib taps, cast copper alloy 15mm bore, screwed down, screwed both ends for iron pipe or for unionS&Fixed complete all as specified and as directed.

S&F 15mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F stop valves, cast copper alloy 15mm bore, screwed down, high pressure, screwed both ends for iron pipe or for unionS&Fixed complete all as specified and as directed.

S&F stainless steel curtain rails of 25mm dia metre stops, rollers etc all as specified and directed.

S&F stainless steel brackets of 25mm dia metre stops, rollers etc all as specified and directed.

S&F vitreous china water closet squating pan Orissa pattern 580 X 440mm white with integral foot rest complete including lime concrete bedding complete all as specified and as directed.

S&F PVC valveless, syphonic action type, flushing cistern, low level of 10 ltr capacity, white with inlet, ball valve, float and handle including brackets the exposed surfaces of brakets shall be painted with two coats of synthetic enamel paint over one coat of primer complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F vitreous chaina wash basin, flat black white, size 550 X 400mm including cutting for and pinning in for bracket and 32mm dia CP waste coupling, 32mm dia PVC waste pipe and connection to drain pipe complete all as specified and as directed.

S&F 110 mm PVC (SWR) vent cowl all as specified and as directed.

S&F PVC (SWR) floor trap 75mm bore plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F PVC Nahani trap with grating including jointing to waste pipe fixed in cement concrete type (1:2:4) B-1 dia of outlet 75mm complete all as specifed and directed

S&F towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F PVC Connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joint and fixing adhessive with all fittings, including all fixed to walls complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in tranches or in floors with all fittings complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and as directed.

S&F 75mm bore with access door complete all as specified and as directed.

S&F 110mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

S&F 75 / 110 mm PVC (SWR) coupler , reducer

S&F soap dish vitreous China white, approximate size 160x160x90 mm fixed to plugs with choromium plated brass screw complete all as specified and as directed.

M&L for machine cut cudappa stone slab 20-25 mm thick in urinal partition and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for granite (of any type)work (table rubbed and polished) 20 mm thick in steps,jambs,pillars,cooking platforms and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

M&L for Screed bed or bedding layer of cement mortar 20 mm thick for laying floors finishes in cement mortar 1:6 complete all as specifed and directed

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar work

S&F aluminium anodised powder coated (min thickness 50 microns) frame for doors, windows, ventilators, complete all as specifed and directed

M&L for Aluminium anodised powder coated door shutters aluminium section weighing not less than 0.45 kg per mtr incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F Aluminium anodised powder coated window and ventilator shutter, sliding type without sash bar, alumn section section weighing not less than 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F decorative aluminium grill,weight not less than 3.131 kg/sqm (with frame of size 20x20mm aluminium cleat screwed to main frame) and fixed to wall/window/ventilator with screws complete all as specified and as directed.

S&F Sheet glass ordinary quality 4.0 mm thick n. exc 0.5 sqm each pane complete all as specifed and directed

S&F Sheet glass ordinary quality 5.5 mm thick exc 0.5 sqm each pane complete all as specifed and directed

S&F Sheet glass ordinary quality 5.5 mm thick exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreature 1.40mm and fixed in aluminium windows, wooden doors etc complete all as specified.

M&L for 10mm thick plastering (screeding) in cement mortar 1:3 on concrete roof surfaces finished even and smooth without using extra cement and using Water Proofing Compound. Note : Water Proofing Compound shall be paid seperately.

Supply only intergral water proofing compound

Supply only liquid water proofing.

M&L for Waterproofing on roof including flashing and junction of parapet, kerb, wall etc. As under (a) Applying bituminous primer on cleaned and dried surface @ 0.7 kg/sqm. (b) Laying by thermo fusion ( torch applied) 3 mm thick APP based polymeric water proofing membrane weighing not less than 3.5kg/sqm and reinforcement with polyester non woven fabric ( not less than 150 gms/sqm) (c) Painting the exposed APP membrane surface with bituminous paint @ 0.15kg/sqm

S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brss handles etc., as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed by Engr in Charge.

M&L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggr) as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore SGSW pipe complete all as specified and as directed.

M&L for Salt glazed stoneware (SGSW) grade ,A, drain pipe 150mm internal dia laid in trenches on concrete bed and jointed complete all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in foundation, manhole and mass fiiling of the manholes all as specified and as directed.

M&L for Providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) in manhole cover slab placed complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B1 using 40 mm graded stone aggregate as in benching and surface channel of manhole complete all as specified and as directed.

M&L for extra for forming fair finished drain or channel using extra cement up to 30 cm inner girth complete all as specified and as directed.

S&F Providing precast cement concrete type B1, 1:2:4 (20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps,quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, Kerb stones etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match with CM 1:6 complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (20mm graded stone aggregates) as in coping including necessary formwork complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C1 ( using 20mm graded stone aggregates) as in plinth protection finished even and fair without using extra cement all as specified.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm grade stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rubber moulded machine pressed precast inter locking paver block with gray cement any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-25 grade laid on 30mm thick stone dust cushioning laid dry to the profile complete all as specified and directd

S&F in repairs tubular rail curtain rod/towel rail, 20mm dia, brass chroium plated complete all as specified and directed by EIC.

S&F for brass chromium plated brackets for 20mm dia tubular curtain rod/towel rail complete all as specified and directed by EIC.

M&L for Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 sqmm with PVC insulated unsheathed stranded copper conductor cable of size 1.5 sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing caping not less than 20mm width with MS Sheet metal sunken switch/terminal box 1.2mm thick and ebonite switch board cover 3.0mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface for One light point controlled by one way switch all as directed and specified. Note : Cutting chases and making good to match with the adjoining surface shall be included in this unit rate.

All as per Item No. 128.00 but for One ceiling/exhaust fan point controlled by one switch and regulator

All as per Item No.128.00 but for One 3 pin 5 Amp socket outlet point on same board

All as per Item No.128.00 but for One 3 pin 5 Amp socket out let point on independent board.

M&L for for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 4.0 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC casing & caping and accessories surface on wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for PVC casing & caping and IS:3419:1976 for accessories), with mild steel/pressed steel sunken boxes with earth dolly duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets etc, including PVC insulated multi-stranded copper conductor 4 Sq mm nominal cross sectional area single core cable as earth continuity conductor to common earth and connecting to earth dolly complee all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent.

S&F switch piano flush type single pole one way 5 Amp

S&F Socket outlet 2 in 1, 5/3 pin 5 Amps

S&F Switch Socket Combination 5 Amps 5 Pin flush type

S&F Ceiling rose , surface bakelite 65 x 50mm three terminals

S&F Electronic regulator 100/120 watt step type.

S&F socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, piano flush type IS: 1239-1988 marked with valid CML No complete all as specified.

S&F switch piano; flush type, single pole, one way, and 15/16 Amps IS: 3854 marked with valid CML No. complete all as specified.

S&F Lamp holder insulated body with back plate for angle holder including 9W LED lamp all as per specified.

S&F 1 x 18Watt universal batten for T5 and T8 lamps as regal batten for LED tube.

S&F Ultra bright glass 18W LED Tube light with very high efficiency suited for installation in existing T8 fitting with G-13 lamp holders as crystal glass LED tube light (Double side connection) .

S&F Heavy duty exhaust fan 300mm sweep metallic type including 3 core copper cable & cutting holes if required etc.

Supply and fix fan ceiling complete including accessories 230V, 1200mm sweep BEE star rated including providing hook if required on site, all as specified and directed.

S&F energy saving and environmental friendly long life 1 x 15 Watt LED Street/security light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07, complete all as specified and directed.

Fabrication, S&F of GI Pipe bracket upto 40mm dia 0.9m long & 2 set of clamps made out of 30 x 5 mm MS flat & fixed with anchor bolt suitable for 1 x 15W LED security light fitting.

S&F sheet metal enclosure factory made for DBs single pole and neutral double door 240Volts 8 way with 100 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping , lagging , testing and commissioning and making good of wall, surfacs all as specified and directed.

S&F single pole and neutral 240 V 40-63 amps all as specified and directed.

S&F MCB Single pole 240 Volt, 6 to 32 Amps all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x 600x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level with top edge of the plate not less than 1.50 mtr below normal ground level connected to galvanised earth wire 4.00mm dia by means of bolts, nuts, check nuts and washers complete upto and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal, common salt, earthing lead 4.00mm dia upto 7.5 mtr 20mm dia medium grade GI watering pipe, GI Protection pipe 15mm dia upto 7.5m long, PPC pit in PCC 1:2:4 type B-1 using 20mm graded stone aggregate, PCC Pit cover including earth work complete all as shown on electrical plate No 5 of SSR 2020 (Part-I)

Supply and fix Water heater storage type, electric, capacity 25 litres. BEE 5 star rated.

S&F switch piano; flush type, with fuse and neon incator for storage geyser single pole, one way, and 15/16 Amps IS: 3854 marked with valid CML No. complete all as specified.

M&L for Two runs of 4 Sq mm as current carrying conductor and one run of 4Sq mm as earth conductor sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of nominal cross section area as under and drawing into and including PVC non metallic rigid conduit, accessories,of medium grade not less than 25mm dia ,including PVC insulated stranded copper conductor nominal cross section area as under of continuous earth wire complete all as specified.

S&F XLPE insulated armoured and pvc sheated heavy duty electric cable of size 4 core 16 sqmm aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete note- rate is inclusive of cable gland & cable lugs.

Excavation in trenches in soft / loose soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable, RCC poles / stays and struts etc. and getting out including trimming sides and forming bottom surface complete all as specified and directed at site.

Returning, filling in including spreading, leveling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays , struts have been erected and tested , all as specified and directed.

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed.

M&L for DWC pipe (HDPE) size inner dia 24mm dia outer dia 32mm suitable for cable protection complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor , 1100 volts grade, cross sectional area 10 sqmm 2 core

S&F GI Water tubing 32mm bore medium grade galvanised with all fittings like socket, union, elbows, bends, tees etc jointed and laid in trenches complete all as specified and directed by Engr-in-Charge.

SVT ENGINEERS AND CONTRACTOR.

Bidder Name

SVT ENGINEERS AND CONTRACTOR.

Kaushalya Buildcon