NIT No: 33/10FC /EEC/CE/NRANVP/2025-27, Nava Raipur Atal Nagar, Dist. Raipur, Dated:21.08.2026

Excavation for all types and sizes of foundations trenches and drains or for any other purpose including disposal of excavated stuff upto all lead and lift including dressing and leveling of pits. In all types of soil

Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto all lead and lift.

Providing and filling in plinth with sand/ Crusher dust under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with all lead and lift

Providing filling and compacting local earth (from approved source pit) in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluidng cost of form work 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-20 Grade

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-25 Grade

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-40 Grade

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Water proofing material: Providing and mixing water proofing material in PCC/ RCC work in the proportion recommended by the manufacturer.

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete: Thermo-Mechanically treated Bars FE 500D

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Foundations, footings, base of columns and plinth beam in any shape and size.

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Wall of any thickness including attached pilasters, buttresses etc. in super structure.

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Window sills, anchor blocks, string course, bends, copings, bed plates and like.

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Columns, Pillars, Piers and likes- rectangular or square in shape

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Beams, lintels, cantilevers & walls

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Weather shade, chhajja, Cornices and mouldings

Providing and laying Manglore pattern tiles 20 mm thick (without hip ridge tiles) on steel/ wooden frame (frame work to be paid separately)

Providing and laying Manglore pattern hips and ridge tiles fixed in cement mortar 1:6 etc. complete

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

DPC: Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including formwork.

Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of inside of plinth masonry wall on using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall below plinth protection at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of outer side of plinth masonrywall using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall at the junction of floor at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: Cement Mortar 1:3 (1 cement : 3 coarse sand)

Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.

Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level:

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand)

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:5 (1 cement : 5 fine sand)

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:5 (1 cement : 5 fine sand)

6mm thick cement plaster of mix: (ceiling) In Cement mortar 1:4 (1 cement : 4 fine sand)

Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 105qm as per relevant IS code 175-45:2021 (Product such as Asian trucare, Berger Happy walls Putty, Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. (This Item to be use in heigher grade painting work Item no.14.65)

Providing and applying Luxury plastic emulsion paint with roller application minimum three coats applied 1.25 lit/105qm up to final finish as per relevant Type - Class D, C, B & A (Glossy /Semi Glossy and Mati, Egg Shell or Satin finish) of required shade (Product such as Asian Royale Shyne, Dulux Velvet Touch, Berger Silk Luxury Emulsion, Nippon Impression Pearl Opus Pure Elegance) inclusive of providing sbro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etu, complete for the work. (with 4 Years Warranty)

Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit/105qm up to final finish as per relevant LS. Code 15489:2013 Type -2 Class D, C (Glossy /Semi Glossy finish) (Product such as Asian Apex Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Eira, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door. windows, floor and surface as sequired with all tools tackles and labour etc complete for the work. (With 3Year Warranty.)

Providing and applying acrylic modified resin EXTERIOR TEXTURED with special quality silica quartz plaster as an intermediate coating on external surface giving protective layer and decorative finish on plastered surface in approved design and shade (product such as Asian Apex Series Duracast Dulux weathersheald sandtax creation) as per manufacturer's specifications inclusive of providing abro tape on edges and article and cleaning of door. windows, floor and surface as required with all tools tackles and labour etc. complete for the work 2.0ram thickness (average) having design scratched with leveled & smooth surface.

Providing and applying Aluminium paint mimimum 2 coats in all metal surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite aluminium paint, Dulux Aliminium paint, Burger Superior Aluminium Paint) with all tools tackle and labour etc. complete for the work.

Providing and fixing chicken mesh weighting not less than 250 gms/sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick wallsjunctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Providing and laying ceramic glazed floor tiles conforming to IS : 15622 of approved size, make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete. Size 300x300mm

Providing and fixing ceramic glazed wall tiles conforming to IS : 15622 of approved make, colours, shades and size on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. Size above 200x300mm

Providing and Laying Glazed Vitrified Floor tiles (GVT/PGVT) with digital print of randon design with water absorption less than 0.05% and conforming to IS : 15622-2017 of 1st quality of approved make, in all colours shades and size mentioned below (+/-10mm). laid on 20mm thick cement Mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone black

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). Granite stone black

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

Extra for nosing in Granite stone for treads.

Plinth protection: Making 50mm thick plinth protection of plain cement concrete 1:3:6 (1cement : 3 coarse sand : 6 graded crushed stone aggregate 20mmnominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with sand including finishing the top smooth.PCC

Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets conforming to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete in profile section applying a priming coat of red oxide zinc chromate primer. Single rebate/ mullion 100mmx50mm size, 1.25mm thick sheet

Providing and fixing flush door shutters, conforming to IS 2202 (Part 1), interior grade, commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains, cross bands and face veneers on both faces of shutters excluding hinges. 35 mm. thick (single leaf)

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. Electric resistance or induction butt welded tubes Grade-300

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately: For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. compl ete. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

Providing and fixing antique/ SS finished brass butt hinges with antique/SS polished MS screw complete: 125x85x5.50mm (Heavy Type)

Providing and fixing antique/ SS finished brass door latch with antique/ SS polished MS screw complete: 300 x16x5 mm

Providing and fixing antique/ SS finished brass tower bolts (Barrel type) with antique/ SS polished MS screw complete: 250 x10 mm

Providing and fixing antique/ SS finished brass handles with antique/ SS polished MS screw complete: 125mm

Providing & fixing 150mm antique/ SS finished brass floor door stopper with rubber cushion and antique/SSpolished MS screw complete to suit the shutter thickness.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 304

Supplying and fixing rolling shutter of approved makes made of M.S. laths interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and out side locking with push and pull arrangement complete but excluding the cost of top cover and spring. 80x1.25mm M.S. Laths

Providing and fixing 27.5cm long wire spring for rolling shutters.

Providing and fixing M.S. sheet top cover for rolling shutter 1.25mm thick

Providing and fixing ball bearing for rolling shutters.

Providing and fixing mechanical device chain and crank operation for operating rolling shutters.

Providing and fixing M.S. fan clamp/hook for ceiling fan made out of 16mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop.

Providing and applying priming coat on steel work with red oxide/ zinc phosphate primer applied @ 0.50 lit /Sqm as per relevant code 3536:1999 ( product such as Asian Zinc phosphate, Dulux Steel primer, Burger Red oxide primer) with all tools tackles and labour etc. complete for the work.

Providing and making moulded mortar band in cement mortar 1:4 (1 cement : 4 fine sand) per cm width: 18 mm thick

Making grove in cement plaster while plastering upto10 mm deep and 10 mm wide.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. iv) 4th and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Random rubble masonry with hard stone in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Coarse Sand) including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand: 12 stone aggregate 20mm nominal size) upto plinth level.

Extra for random rubble masonry with hard stone in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for random rubble masonry with hard stone in square or rectangular pillars.

Raising manhole with cover and frame slab to required level including dismantling existing slab, taking out the existing CI frame & cover of manhole and raising it upto ground/ road level, refixing of frame and cover in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 crushed stone aggregate 20mm) all around the frame, including making good the damage, form work, curing, complete. (Brick work of raising depth of manhole to be paid separately) Rectangular manhole 120x90 cm with circular cover 560 mm dia of grade HD - 20

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 20 mm nominal outer dia .Pipes. (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 25 mm nominal outer dia .Pipes. (water supply)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 32 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 50 mm nominal outer dia .Pipes. (up water) (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 100mm nominal inner dia pipes

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 75 mm dia pipe (for waste water)

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 110 mm dia (for Sewerage)

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Vent covel 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. P trap 110mmx110mm long

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Nahani trap 110x75mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Multi floor trap 110

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain reducing Tee 110x75mm

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Coloured pedestal type

Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: Flat back half stall urinal of size 460x380x250mm

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : White Oval or round size 550x400mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Bib cock (350 grams)

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Stop cock (350 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Long nose bib cock (500gms)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Wall mixer with elegant knob (1400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bottle trap set with extension pipes

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Toilet paper holder

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Soap dish plate

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Shower rose (revolving type) (150mm)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel rail (600mm long x 20mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel ring (150 mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Health foscet (hand jet) with flexible connection pipe (for WC)

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing 600x450 mm beveled edge 4mm mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges rounded off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 75 mm dia pipe

Constructing masonry Chamber 30x30x50 cm, inside with fly ash bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site decayed cow dung manure from approved source, including loading unloading and carriage upto 5 km ( sludge measured in stacks will be reduced by 8% for payment).

Spreading of sludge, dump manure or/ and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately).

Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In rows 5 cm apart in either direction. (50%)

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Hedges like Alife, Dorenta, Tikoma etc

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Furn like Arica, China etc (3 year old

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Hibiscus (Flower)/ Rose

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Carpet grass (well developed) (50%)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep.

Stone work with DHOLPUR SAND STONE (machine cut edge) exposed face machine cut and table rubbed with rough backing for wall lining etc. (Veneer work) upto 10 metre height, backing filled with a grout of 20 mm thick cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment matching the stone shade. (To be secured to the backing by means of cramps which shall be paid separately) 50mm. Thick

Supply and fixing of polymer precoated galvalume profile sheets (PPGL) of approved size, shape and pitch of corrugation, total coated thickness (TCT) 0.60 mm +/- 5%, epoxy primer on both side of the sheet and colour polyester top coat 18-20 microns and 6-7 microns on bottom. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Excavation in Soil (by Mechanical Means.) Excavation for roadway in soil using mechanical means including loading in tipper for carrying of cut earth to embankment site and unloading with all lifts and lead.

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, , carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 A Plant mix method (with Mechanically crushed stone only) (a) For Lower Sub-base with (i) Grading-III Material

Providing & laying precast interlocking concrete blocks of minimum compressive strength of 300 kg/sq.cm and approved size , shape/ pattern over coarse sand bed of thickness upto 40 mm and joints thick filled with fine sand including leveling with surface vibrator, temping and sweeping etc. complete as per IRCSP- 63-2004. 60mm thick Polymer coated coloured precast interlock concrete blocks

Manufacturing, supply & fixing of precast kerb stone of size 400mmx259mmx200mm thick made of M-20 concrete rectangular in shape with one corner chamfered by 100 mm x 100 mm as approved design i/c cost of all material, labour and curing etc. complete.

Providing and planting of 3‟0” to 4‟0” heighted wasingtonia, filipheria/bismarkia novelist plam plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). (Foxtail Palm, Phonix Palm)Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of Bogenbelia dwarf, chandni dwarf, kaner dwarf vr flower bearing plants with 0‟9” x 0‟9” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). ( Nicodia,Euphorbia milii). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of dwarf red Ekalyha plants showing mass effect view with 0‟9” x 0‟9”x1‟0” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed.

Providing and planting of Golden durenta multi branches plants for showing mass effect in 0‟6” x 0‟6” distance with soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Planting of Trees and their maintenance for one year (Planting of trees by the row side(Avenue trees) in 0.60m dia.holes, 1m. Deep dug in the ground, mixing the soil with decayed farm yard/sludge manure,planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year

Tree Guard with MS Angle Iron and Steel Wire (Providing and fixing tree guard 0.60 meter square, 2.00 meter high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm at 100mm centre to centre and steel wire 3 mm dia. welded and fabricated as per design in two halves bolted together, fixed in ground with P.C.C M-10 of dimensions 150x150x200mm.)

Dismantling of flexible pavements and disposal of dismantled materials with all lifts and lead, stacking serviceable and unserviceable materials separately and as per relevant clauses of section-200. Bituminous courses

Dismantling of flexible pavements and disposal of dismantled materials with all lifts and lead, stacking serviceable and unserviceable materials separately and as per relevant clauses of section-200. Granular courses

Dismantling kerb stone channel by manual means and disposal of dismantled material with all lifts and lead.

Dismantling of cement concrete pavement i/c breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials with all lifts and lead, stacking serviceable and unserviceable materials separately and as per relevant clauses of section-200.

Dismantling of barbed wire fencing/wire mesh fencing including posts, foundation concrete, back filling of pit by manual means including disposal of dismantled material with all lifts and lead, stacking serviceable material and unserviceable material separately.

Dismantling of CI water pipe line 600 mm dia including disposal with all lifts and lead , stacking of serviceable material and unserviceable material separately under supervision of concerned department.

Providing & laying precast interlocking concrete blocks of minimum compressive strength of 300 kg/sq.cm and approved size , shape/ pattern over coarse sand bed of thickness upto 40 mm and joints thick filled with fine sand including leveling with surface vibrator, temping and sweeping etc. complete as per IRCSP- 63-2004. Removing of existing laid 60mm/80mm thick precast interlocking concrete blocks without any damaged in any shape and pattern, over coarse sand bed with stacking of block in proper manner with in the lead of 100.00 mt inclusive of all labour etc. complete the work

Supplying and laying following size RCC Hume pipe class NP-2 (in standard length of 2 metre) with collar in ground below road, path etc at a depth not less than 50 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification 300 mm dia

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X70 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X50 sqmm

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 120 mm dia

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) & IS: 7098 (1988, Part 1) 4 x 10 sq. mm

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 4X 10 sq. mm (19 mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 3½ X 70 sq. mm (35 mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 3½ X 50 sq. mm (32 mm)

Supplying and fixing SP MCB, 240 volts, 'B' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6-32A SP MCB C series 10kA as out going feeder.

Supplying and fixing on surface/ recess horizontal type following way,415 volts TPN MCB distribution board consumer unit of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator 6 way Double door

Supplying and fixing TPN MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 63 amps

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5). Short Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Short Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards .Medium Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Long Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standardsExtra Long Point I

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 1.5 sqmm in 20 mm conduit

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 2.5 sqmm in 20 mm conduit

Supply and fixing of metal box of following sizes in recess with suitable size phenolic laminated sheet cover in FRLSont including painting, accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 100mm x 100mm x 60mm deep

Supply and fixing of GI box of following sizes in recess with modular base & cover plate for modular switches including accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 125mmx75mm

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.. 9 Watt

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt -4 feet

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Short Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Medium Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Long Point

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 4 sqmm in 25 mm conduit

Earthing with G.I. earth pipe 3 mtr long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering,excavation and refilling the trench etc. as required.

Providing, Fixing and Installing Gazebo, DGZ_003) 360cm x 360 cm upto specified hight including bolts and connections as may be required to set system, in horizontal/ vertical/inclined alignment tied with; including necessary bolts or G.I. fixtures to angle iron all complete as per direction of Engineer-in-charge.

Providing and Fixing and installations with Garden Bench (DGB - 011) including bolts and connections as may be required to set system, in horizontal/ vertical/inclined alignment tied with; including necessarysupport, all complete as per direction of Engineer-in-charge.

Inbuilt of drain cover slab in providing perforated holes using PVC pipe 50 mm dia. including cost of allmaterials and labour involved with all leads and lifts etc. as per drawing and direction of Engineer in Charge.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 40 mm dia

Item No.

Supplying and laying following size RCC Hume pipe class NP-2 (in standard length of 2 metre) with collar in ground below road, path etc at a depth not less than 50 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification 300 mm dia

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X70 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X50 sqmm

Main Panel Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as per direction of Engineer INCOMER 4 pole MCCB, 200A, Adjustable Microprocessor Release, 35KA -1 nos BUS-BAR 1 Set of 300A 4P Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 4 pole MCCB, 100A, Adjustable Microprocessor Release, 35KA - 2 nos 4P MCCB, 63A 35KA - 4 nos

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 40 mm dia

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 120 mm dia

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) & IS: 7098 (1988, Part 1) 4 x 10 sq. mm

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 4X 10 sq. mm (19 mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 3½ X 70 sq. mm (35 mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 3½ X 50 sq. mm (32 mm)

Supplying and fixing SP MCB, 240 volts, 'B' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6-32A SP MCB C series 10kA as out going feeder.

Supplying and fixing on surface/ recess horizontal type following way,415 volts TPN MCB distribution board consumer unit of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator 6 way Double door

Supplying and fixing TPN MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 63 amps

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5). Short Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 Sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.l, box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Short Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards .Medium Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Long Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standardsExtra Long Point I

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 1.5 sqmm in 20 mm conduit

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 2.5 sqmm in 20 mm conduit

Supply and fixing of metal box of following sizes in recess with suitable size phenolic laminated sheet cover in FRLSont including painting, accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 100mm x 100mm x 60mm deep

Supply and fixing of GI box of following sizes in recess with modular base & cover plate for modular switches including accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 125mmx75mm

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.. 9 Watt

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt -4 feet

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Short Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Medium Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Long Point

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 4 sqmm in 25 mm conduit

Earthing with G.I. earth pipe 3 mtr long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering,excavation and refilling the trench etc. as required.