Jet Pump, Monoblock Pump, Bare Pump, Underwater Pump VTPump India mark - 2 and Mark - 3 Hand Pump repairing and spare parts rate for Zilla Parishad Bhandara.

Jet Pump,Monoblock Pump, Bare Pump Underwater Pum all Submit Rate as per GSDA-ITEM Sheet

India Mark -2 & 3 Hand Pump Repairing Drive out the Pipe line with diameter of 65.0 mm.

Drive out the Pipe line with diameter of 65.0 m.m which fell in well.

Drive out the Pipe line with diameter of 32.0 m.m from which fell in well.

Drive out the Pipe line with diameter of 32.0 m.m from well.

To pull out the Stucked, fell or caught in drag Pump Set. ( Contractor use their own tools.)

To increse or reduce the pipe line of Jet Pump inh well. ( For every 3.0 m. )

To fit new pump set (Upto 1.0 to 5.0 HP) in well/borewell , to give panel wiring earthig test report & start after electric supply. (Z.P. provides Pumpset panel, earthing material G.I. wire, plate, pipe and other assesaries.)

To rewinding electric motor with copper wire , above rate valid for without returning old copper wire, 1.0 HP to 5.0 HP open pump motor rewinding.

To test electric pump on site ( transport and with minor repairing)

To repaire panel board & starter of all types motor & Any HP control panel starter minor repairing to fit grip set, rotory switch, contactor plate, ampear meter, volt meter, on-off switch, fuse and minor wiring.

Starter panel board main repairing & to fit coil relay, single phasing preventer water label guard &Total wiring of 1.0 HP to 10.0 Hp pump.

Starter panel board main repairing & to fit coilrelay, single phasing

Preventer water label guard &Total wiring of 10.0 HP to 30 Hp pump.

Preventer water label guard & total wiring of 31.0 HP to 40 Hp pump.

To remove tin shed flushing of pump if necessary and fit as it is after work.

To remove handpump with pipeline for flushing and insert 10 feet G.I. pipeline towards 32 mm. dimeter& remove after flashing and fit handpump as it is before.

To remove handpump for capacity test and after testing fit as it is before.

Yield Test Single phase 1 HP to 2 Hp electric pump capacity test for regular three Hour with help of generator

Yield Test 1 HP to 2 Hp electric pump capacity test for regular three Hour without help of generator with necc equip

Yield Test 2 HP to 5 Hp electric pump capacity test for regular three Hour with help of generator with necc equipment

Yield Test 2 HP to 5 Hp electric pump capacity test for regular three Hour without help of generator with necc equip

i) Other material G.I. Coupling heavy duty 32 mm.

ii) G.I. Coupling heavy duty 40 mm.

iii) G.I. Coupling heavy duty 50 mm.

iv) G.I. Coupling heavy duty 65 mm.

v) G.I. Coupling heavy duty 75 mm.

vi) G.I. Coupling heavy duty 100 mm.

vii) G.I. Coupling heavy duty 125 mm.

viii) G.I. Coupling heavy duty 150 mm.

Bend heavy duty i) 32 mm.

iii) 50 mm.

vii) 125 mm.

viii) 150 mm.

3) Foot valve : i) 32 mm.

iii) 50 mm.

vii) 125 mm.

viii) 150 mm.

Wooden board 3 x 2 f x ½ “

Iron box 18 guage tin 3f x 2f x 1f

G.I.Pipe 1½“ / 1¼ “ cutting threding

G.I.Pipe 2“ cutting threding

G.I.Pipe 2½“ / 3 “ cutting threding

E) Submercible Motor Rewinding : 1.0 HP to 3.5 HP

4.0 HP to 5.0 HP

6.0 HP to 10.0 HP

11.0 HP to 15.0 HP

16.0 HP to 20.0 HP

21.0 HP to 30.0 HP

31.0 HP to 50.0 HP

F) To Remove Motor Pump Set with Pipeline from well: 1 HP to 6.0 HP

7.0 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

G) To pull out the Stuck, fell or caught in dreg Pump Set with pipeline from well: 1) 1 HP to 6.0 HP

2) 7.0 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

H) To fit motor pump in well with pipe line : 1) 1 HP to 6.0 HP

2) 7.0 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

I) To increase or reduse pipeline of submercible pump in well Rate 3 meter / per pipe: 1 HP to 6.0 HP

7.0 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

J) To submit in the office pump, : 1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

K) New pump set (Upto 1.0 to 5.0 HP) : 1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

L) To open sub motor, repairing, fitting and testing.: 1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

M) To open sub pump, repairing, fitting and testing.: 1) 1 HP to 7.5 HP

2) 8.5 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

N) To repaire sub motor and sub pump:To sub motor / pump bush fitting per

Damage stater repairing

Rotorshaft turning and polishing

Damage Rotor repairing (Rewinding)

Sub pump shaft turning & polishing

To joint cable with kit

O) Sub motor & sub pump spare parts1 to 5 HP: i) Sub motor bush

ii) Sub pump bush

Thrust Bearing block

Thrust Bearing full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Impeller

ii) Brass Impeller

Neck ring

Diffuser

Pump key

Rubber parts kit

Submersible Motor base

Strainer

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Allen srew

SS Sleeve motor /pump

SS Sleeve cover

O) Sub motor & sub pump spare parts1 to 7.5 HP: i) Sub motor bush

ii) Sub pump bush

Thrust Bearing block

Thrust Bearing full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Impeller

ii) Brass Impeller

Neck ring

Diffuser

Pump key

Rubber parts kit

Submersible Motor base

Strainer

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Allen srew

SS Sleeve motor /pump

SS Sleeve cover

O) Sub motor & sub pump spare parts 8 to15 HP : i) Sub motor bush

ii) Sub pump bush

Thrust Bearing block

Thrust Bearing full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Impeller

ii) Brass Impeller

Neck ring

Diffuser

Pump key

Rubber parts kit

Submersible Motor base

Strainer

Male- Female bush

Male- Female key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Allen srew

SS Sleeve motor /pump

SS Sleeve cover

O) Sub motor & sub pump spare parts 16 to30 HP: i) Sub motor bush

ii) Sub pump bush

Thrust Bearing block

Thrust Bearing full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Impeller

ii) Brass Impeller

Neck ring

Diffuser

Pump key

Rubber parts kit

Sub motor base

Strainer

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing i) Upper

ii) Lower

Allen srew

SS Sleeve motor /pump

SS Sleeve cover

1) Three ply core flat flexible submersible cable: i) 1.5 sq.mm.

ii) 2.5 sq.mm.

iii) 4 sq.mm.

iv) 6 sq.mm.

v) 10 sq.mm.

vi) 1.5 sq.mm.

1) Three ply core flat : Arm cable : i) 1.00 sq.mm.

ii) 1.50 sq.mm.

iii) 2.50 sq.mm.

iv) 4.00 sq.mm.

v) 6.00 sq.mm.

vi) 10.00 sq.mm.

vii) 16.00 sq.mm.

viii) 25.00 sq.mm.

ix) 35.00 sq.mm.

x) 50.00 sq.mm.

Copper wire P.V.C. insulated & P.V.C. coated: i) 3/20

Copper wire P.V.C. insulated & P.V.C. coated: ii) 7/20

Copper wire P.V.C. insulated & P.V.C. coated: iii) 7/16

27) New Pump Shaft i) 1.5 HP to 6 HP

27) New Pump Shaft ii) 7.5 HP to 15 HP

27) New Pump Shaft iii) 16 HP to 30 HP

Borewell Protecting Plate

Borewell Protecting Cap

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 25HP: Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out Column assembly with pipeline from well

To fit Column assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing i) Line shaft

ii) Column pipe

iii) Oil tube

Cutting & Threading i) Line shaft (R.H./L.H)

ii) Column pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new Flange, threading collar, welding, nutbolt in Column pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 35HP: Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out Column assembly with pipeline from well

To fit Column assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing i) Line shaft

ii) Column pipe

iii) Oil tube

Cutting & Threading i) Line shaft (R.H./L.H)

ii) Column pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new Flange, threading coller, welding, nutbolt in Column pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 40HP : Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out Column assembly with pipeline from well

To fit Column assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing i) Line shaft

ii) Column pipe

iii) Oil tube

Cutting & Threading i) Line shaft (R.H./L.H)

ii) Column pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new Flange, threading coller, welding, nutbolt in Column pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

Q) 25 HP to 40 HP V.T. Pump Spare Part 25HP : 1) V.T. MotorBearing i) Upper

ii) Lower

Discharge & sectioncaseBearing bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Seat

T.T. Plate Bush

Neck Ring (Gun Metal)

Impeller (Gun Metal)

Browl assembly casing

6” Column pipe M.s.

8” Column pipe M.s.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impeller pump shaft

Latern Ring

Guide spider

Column Pipe Coupling

Line shaft Coupling

Oil tube Bearing

Gland nut

Top Oil Tube

SpiderBearing Bush

Guide Spider Rubber Bush with Sirclip

Rubber Bush/Bearing

Line Shaft Sleeve S.S.

Water Lubricating Tube

Stuffing Box Bush & with gaskit

Stuffing Box Bearing

Latern Ring

Sole Plate

Base Plate

Water Deflector

Q) 25 HP to 40 HP V.T. Pum Spare Part 25HP : 1) V.T. Motor Bearing

i) Upper

ii) Lower

Discharge & section case Bearing bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Seat

T.T. Plate Bush

Neck Ring (Gun Metal)

Impeller (Gun Metal)

Browl assembly casing

6” Column pipe M.S.

8” Column pipe M.S.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impeller pump shaft

Latern Ring

Guide spider

Column Pipe Coupling

Line shaft Coupling

Oil tube Bearing

Gland nut

Top Oil Tube

Spider Bearing Bush

Guide Spider Rubber Bush with Circlip

Rubber Bush/Bearing

Line Shaft Sleeve S.S.

Water Lubricating Tube

Stuffing Box Bush & with gasket

Stuffing Box Bearing

Latern Ring

Sole Plate

Base Plate

Water Deflector

Q) 25 HP to 40 HP V.T. Pum Spare Part 40HP: 1) V.T. Motor Bearing i) Upper

ii) Lower

Discharge & section case Bearing bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Seat

T.T. Plate Bush

Neck Ring (Gun Metal)

Impeller (Gun Metal)

Browl assembly casing

6” Column pipe M.S.

8” Column pipe M.S.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impeller pump shaft

Latern Ring

Guide spider

Column Pipe Coupling

Line shaft Coupling

Oil tubeBearing

Gland nut

Top Oil Tube

Spider Bearing Bush

Guide Spider Rubber Bush with Sirclip

Rubber Bush/Bearing

Line Shaft Sleeve S.S.

Water Lubricating Tube

Stuffing Box Bush & with gaskit

Stuffing BoxBearing

Latern Ring

Sole Plate

Base Plate

Water Deflector

i) Drive out 1 HP to 3 HP Monoblock Pump

ii) Drive out 4 HP to 10 HP Monoblock Pump

iii) Drive out 10 HP to 30 HP Monoblock Pump

ii) 1 to 3 HP Monoblock Motor Rewinding

iii) 4 to 5 HP Monoblock Motor Rewinding

iv) 6 to 7½ HP Monoblock Motor Rewinding

v) 8 to 10 HP Monoblock Motor Rewinding

vi) 10 to 15 HP Monoblock Motor Rewinding

Monoblock Pump Open, Repairing, Fitting & Testing i) 1 to 3 HP

Monoblock Pump Open, Repairing, Fitting & Testing ii) 3 to 5 HP

Monoblock Pump Open, Repairing, Fitting & Testing iii) 6 to 10 HP

Monoblock Pump Open, Repairing, Fitting & Testing iv ) 10 to 15 HP

RotorPump Shaft Turning & Polishing i) 1 to 5 HP

Rotor Pump Shaft Turning & Polishingii) 6 to 10 HP

Rotor Pump Shaft Turning & Polishingii) 11 to 20 HP

To make Monoblock Pump Bush & Housing (Bearing ) i) 1 to3 HP

To make Monoblock Pump Bush & Housing (Bearing ) ii) 3 to 5 HP

To make Monoblock Pump Bush & Housing (Bearing ) iii) 6 to 10 HP

To make Monoblock Pump Bush & Housing (Bearing ) iii) 11 to 15 HP

To Fit New Pump Set i) 1 to 3 HP

To Fit New Pump Set ii) 3 to 5 HP

To Fit New Pump Set iii) 6 to 10 HP

To Fit New Pump Set iii) 10 to 15 HP

T) Monoblock Pump Spare Parts Bearing 1 to 1.5 HP(Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star-Nut Key

Bearing Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotorfitted shaft

Latern Ring

Brass Impeller

Impeller C.I.

Diffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts 2 to 3 HP Bearing (Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star nut Key

Bearing Plate both side

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotorfitted shaft

Latern Ring

Brass Impeller

Impeller C.I.

Diffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts 4 to 5 HP Bearing (Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star-Nut Key

Bearing Plate both side

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotorfitted shaft

Latern Ring

Brass Impeller

C.I. Impeller

Diffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts Bearing 6 to 7½HP (Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star-Nut Key

Bearing Plate both side

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotor-fitted shaft

Latern Ring

Impeller brass

Impeller C.I.

Diffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts Bearing 8 to 10HP (Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star-Nut Key

Bearing Plate both side

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotor fitted shaft

Latern Ring

Impeller brass

Impeller C.I.

Diffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motor body

Spacer

Fan cover

Water Deflector

U) Monoblock Pump Spare Parts Bearing 11 to 15HP (Driving side)

Bearing (Driven side)

Impeller Key

Pump Bush

Air Fan

Star-Nut Key

Bearing Plate both side

Water seal

Gland Rope

Gland Bush

Gland Plate

Rotor fitted shaft

Latern Ring

Impeller brass

Impeller C.I.

Deffuser

Bearing housing

Neck Ring

Foot valve

Flange (Delivery/ suction)

Shaft Sleeve

Delivery casing

Stater Fitted motor body

Spacer

Fan cover

Water Deflector

U) Bare Pump Repairing To drive out bare pump i) 10 to 20 HP

ii) 21 to 50 HP

Bare Pump to open, repairing, fitting & Testing i) 10 to 20 HP

ii) 21 to 50 HP

Pump shaft turning & polishing i) 10 to 20 HP

ii) 21 to 50 HP

To make pump bush & housing (Bearing ) i) 10 to 20 HP

ii) 21 to 50 HP

To fit new bare pump i) 10 to 20 HP

ii) 21 to 50 HP

Pump repairing & fitting i) 10 to 20 HP

ii) 21 to 50 HP

To make gland bush housing i) 10 to 20 HP

ii) 21 to 50 HP

Drive out bare pump pipe line with foot valve i) 10 to 20 HP

ii) 21 to 50 HP

To fit bare pump pipeline with foot valve i) 10 to 20 HP

ii) 21 to 50 HP

V) Bare Pump spare parts 10 to 15 HPBearing (BallBearing )

Roller Bearing

Impeller Key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Impeller Brass

Impeller (C.I)

Diffuser

Bearing housing

Neck ring (small)

Neck ring (big)

Flasher

Foot valve

Check nut

Impeller housing

Rotor casing

Rotor

Delivery casing

Stuffing box bush

Shaft Sleeve

Water deflector

Coupling half flexible

Bearing cover

Grease cup

Flange section/ delivery

V) Bare Pump spare parts 16 to 20HPBearing (BallBearing )

Roller Bearing

Impeller Key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Brass Impeller

Impeller(C.I)

Diffuser

Bearing housing

Neck ring (small)

Neck ring (big)

Flasher

Foot valve

Check nut

Impeller housing

Rotor casing

Rotor

Delivery casing

Stuffing box bush

Shaft Sleeve

Water deflector

Coupling half flexible

Bearing cover

Grease cup

Flange section/ delivery

V) Bare Pump spare parts 21 to 50 HPBearing (BallBearing )

Rolor Bearing

Impeller key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Impeller brass

Impeller (C.I)

Diffuser

Bearing housing

Neck ring (small)

Neck ring (big)

Flasher

Foot valve

Check nut

Impeller housing

Rotor casing

Rotor

Delivery casing

Stuffing box bush

Shaft Sleeve

Water deflector

Coupling half flexible

Bearing cover

Grease cup

Flange section/ delivery

W) Bare Motor repairing Drive out bare motor

W) Bare Motor repairing Drive out bare motor i) 10 to 20 HP

W) Bare Motor repairing Drive out bare motor ii) 21 to 50 HP

Bare motor rewinding i) 1 to 5 HP

Bare motor rewinding ii) 6 to 10 HP

Bare motor rewinding iii) 11 to 15 HP

Bare motor rewinding iv) 16 to 20 HP

Bare motor rewindingv) 21 to 30 HP

Bare motor rewinding vi) 31 to 35 HP

Bare motor rewinding vii) 36 to 40 HP

Bare motor rewinding viii) 41 to 50 HP.

Motor opening, over oiling, fitting & testingi) 1 to 5 HP

Motor opening, over oiling, fitting & testing ii) 6 to 10 HP

Motor opening, over oiling, fitting & testing iii) 11 to 15 HP

Motor opening, over oiling, fitting & testing iv) 16 to 20 HP

Motor opening, over oiling, fitting & testing v) 21 to 30 HP

Motor opening, over oiling, fitting & testing vi) 31 to 35 HP

Motor opening, over oiling, fitting & testing vii) 36 to 40 HP

Motor opening, over oiling, fitting & testing viii) 41 to 50 HP.

Rotor shaft turning & polishing i) 1 to 5 HP

Rotor shaft turning & polishing ii) 6 to 10 HP

Rotor shaft turning & polishing iii) 11 to 15 HP

Rotor shaft turning & polishing iv) 16 to 20 HP

Rotor shaft turning & polishing v) 21 to 30 HP

Rotor shaft turning & polishing vi) 31 to 35 HP

Rotor shaft turning & polishing vii) 36 to 40 HP

Rotor shaft turning & polishing viii) 41 to 50 HP.

To make motor bush & housing (Bearing Seat) i) 1 to 5 HP

To make motor bush & housing (Bearing Seat) ii) 6 to 10 HP

To make motor bush & housing (Bearing Seat) iii) 11 to 15 HP

To make motor bush & housing (Bearing Seat) iv) 16 to 20 HP

To make motor bush & housing (Bearing Seat) v) 21 to 30 HP

To make motor bush & housing (Bearing Seat) vi) 31 to 35 HP

To make motor bush & housing (Bearing Seat) vii) 36 to 40 HP

To make motor bush & housing (Bearing Seat) viii) 41 to 50 HP.

To fit new motor i) 1 to 5 HP

To fit new motor ii) 6 to 10 HP

To fit new motor iii) 11 to 15 HP

To fit new motor iv) 16 to 20 HP

To fit new motor v) 21 to 30 HP

To fit new motor vi) 31 to 35 HP

To fit new motor vii) 36 to 40 HP

To fit new motor viii) 41 to 50 HP.

Panel board & Starter repairing i) 1 to 5 HP

Panel board & Starter repairing ii) 6 to 10 HP

Panel board & Starter repairing iii) 11 to 15 HP

Panel board & Starter repairing iv) 16 to 20 HP

Panel board & Starter repairing v) 21 to 30 HP

Panel board & Starter repairing vi) 31 to 35 HP

Panel board & Starter repairing vii) 36 to 40 HP

Panel board & Starter repairing viii) 41 to 50 HP.

To fit motor as it is i) 1 to 5 HP

To fit motor as it is ii) 6 to 10 HP

To fit motor as it is iii) 11 to 15 HP

To fit motor as it is iv) 16 to 20 HP

To fit motor as it is v) 21 to 30 HP

To fit motor as it is vi) 31 to 35 HP

To fit motor as it is vii) 36 to 40 HP

To fit motor as it is viii) 41 to 50 HP.

X) Bare Motor spare parts 10 to 15 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Rotor assembly

Stud nut kit

Nut bolt kit

X) Bare Motor spare parts 6 to 20 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Rotorassembly

Stud nut kit

Nut bolt kit

X) Bare Motor spare parts 21 to 50 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Rotor assembly

Stud nut kit

Nut bolt kit

Y) Vaccum Pump Repairing Drive out pump i) 1 to 3 HP

Y) Vaccum Pump Repairing Drive out pump ii) 4 to 5 HP

Motor Rewinding i) 1 to 3 HP

Motor Rewinding ii) 4 to 5 HP

Pump opening, repairing, over oiling, fitting & testing i) 1 to 3 HP

Pump opening, repairing, over oiling, fitting & testing ii) 4 to 5 HP

Rotor shaft turning & polishing i) 1 to 3 HP

Rotor shaft turning & polishing ii) 4 to 5 HP

To make Vaccum pump bush &Bearing housing i) 1 to 3 HP

To make Vaccum pump bush &Bearing housing ii) 4 to 5 HP

To fit new pump set i) 1 to 3 HP

To fit new pump set ii) 4 to 5 HP

Panel board & starter repairing i) 1 to 3 HP

Panel board & starter repairing ii) 4 to 5 HP

Z) Vaccum Pump Spare Parts 1 to 3 HP : Bearing

Impeller Key

Pump bush

Air fan

Star nut key

Bearing plate both side

Mechanical seal

Gland rope

Gland bush

Gland plate

Rotor fitted shaft

Latern Ring

Rotor G.M.

Fan cover

Spacer

Bearing housing

Neck Ring

Port plate

Flange (Delivery/ section)

Shaft Sleeve

Suction & delivery chember

Starter fitted motorbody

Tie rod

Rotor casing

Liquid diflector

Z) Vaccum Pump Spare Parts 4 to 5 HP : Bearing

Impeller Key

Pump bush

Air fan

Star nut key

Bearing plate both side

Mechanical seal

Gland rope

Gland bush

Gland plate

Rotor-fitted shaft

Latern Ring

Rotor G.M.

Fan cover

Spacer

Bearing housing

Neck Ring

Port plate

Flange (Delivery/ section)

Shaft Sleeve

Suction & delivery chember

Starter fitted motorbody

Tie rod

Rotor casing

Liquid deflector

Starter Relay i) 6 to 10 A.

ii) 9 to 14 A.

iii) 13 to 21 A

iv) 19 to 27 A

Starter no volt & over load coil

Contactor set full i) S. K. -1

iii) M.L. -2

vii) M.L. - 6

viii) M.L. - 7

Relay plate (kit)

Contactor point kit i) S. K. -1

iii) M.L. -2

vii) M.L. - 6

viii) M.L. - 7

i) Fuse grip 16 A.

ii) Fuse grip 32 A.

iii) Fuse grip 63 A.

iv) Fuse grip 100 A

v) Fuse grip 200 A..

Fuse Base i) 16 A.

Connector Plate i) Volt meter 0-440 Volt small

ii) Volt meter 0-440 Volt Big

Ampere meter i) 0 to 15 A.

ii) 0 to 50 A.

iii) 0 to 100 A.

Capasitor 1 K.V.A.R.

Single Phasing Preventor

Water Level Guard with 60 M. wire

On-Off Rotory switch

Volt meter /Ampereee meter switch

Nuon Indicator Lamp

Main Switch 440 Volt three phase i) 16 A.

M.C.C.B. Unit i) 32 A.

H.R. C. Fuse i) 100 A.

Auxiilary Coil

Timer Coil

C.T. coil i) 60 A.

Tunge Tester

Multi meter

Insulation Tester

Meger

Hand gloves - 1 pair (Rubber)

Insulated Rubber Matting

To Earthing with arthing 300 x 300 x 50 mm. earthing plate, G I. pipe & earthing wire

To Earthing with earthing 450 x 450 x 50 mm. earthing plate, G I. pipe & earthing wire

Earthing wire 14 to 6 guage

Starter D.O.L

i) 1 to 5 HP

ii) 5 to 10 HP

iii) Star Delta auto 10 to 20 HP

vi) Star Delta auto 21 to 30 HP

v) Auto transformer starter 20 to 30 HP

vi) Auto transformer starter 31 to 50 HP

transformer coil rewinding with copper wire in transformer starter. without returning old copper wire.

Change over switch 50 A. 3 phase

Change over switch 100 A. 3 phase

Change over switch 200 A. 3 phase

Bus bar 30 to 50 HP

Transformer Oil

1) :- Providing, erecting and giving test of 100 mm dia. submersible pump sets confirming to IS 8034 and motor confirming IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and Motor suitable for working on 415 V± 10%, 3Ph, 50 Hz., A.C. supply, Cable guard, thrust carbon/fibre bearing to accept entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable suction stainer shall also be provided. 3 core, single/double run copper conductor submersible type flat cable 3 Mtr. and 3 pairs of erection clamps. Rates per pump upto 20 stages (as per design) 1.0 HP

Submersible pump 150 mm dia (with bronze /Stainless (CF8M) impeller) up to 8 stages 1.0 HP

Submersible pump 150 mm dia (with bronze /Stainless (CF8M) impeller) up to 12 stages 10.0 HP

Submersible pump 150 mm dia (with bronze /Stainless (CF8M) impeller) up to 15 stages 17.5 HP

Submersible Pump 200mm dia (withBronze / Stainless steel (CF8M) Impeller)upto5 stages of category A & B 7.5 HP

Submersible Pump 200mm dia (with Bronze /Stainless steel (CF8M) Impeller)upto 8 stages of category A & B 15 HP

Submersible Pump 250mm dia (withBronze / Stainless steel(CF8M) Impeller)upto8 stages of category A & B 15 HP

Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming toIS 8967-8986 with waterproof winding. Pump shall be suitable for various delivery head and dIsc harge with stainless steel shaft. Motor suitable for working on 415 V + 10%, 3 Ph, 50 Hz A.C. Su pply, with ca ble guard, thrustcarbon / fibre bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction trainer. Pump s hould have suitable discharge outlet as per man ufac t mer’s des ign. Antithruststreamlined non return valve s haII be provided with the pump. 3 m submersible c opper cond‹ictor cable in single / double run and 2 pairs of s uitable s ize erection clamp10 mm thick shall be provided with each pump..Submersible Pump 250 mm dia. (with Bronze / Stainless steel CF8M) impeller up to 8 stages of catagory A & B 35 HP

Supply rate should be increase per stage more than 8 Stage

Supply rate should be increase per stage more than 8 Stage

Supply rate should be increase per stage more than 8 Stage

Supply rate should be increase per stage more than 8 Stage

Supply rate should be increase per stage more than 8 Stage

Submersible Monoblock (with bronze / stainless steel (CF8M) Impeller ) Horizontal/vertical -upto 3 stages ( Motor with water lubricated bearing to accept entire hydraulice threst ) 3.0 HP

V.T. Pump erection charges (For column length up to 6 m. Erecting, commissioning and giving test of Vertical Turbine giving test of Vertical Turbine Pump (Water Lubricated) including bowl assembly and dischargeheadetconprovided channel / RSJ / RCC beam including erecting on provided sole plate with blue matching. Up to 30 HP

31 HP to 100 HP

101 HP to 200 HP

201 HP to 300 HP

above 300 HP

Sewage Pumps-SupplyingNon clog SubmersiblePumpsuitable for sewage/ Liquid waste applicationwithstandardMOC and given duty points as below head upto 10 m 1 HP (Up to 9000 LPH)

2 HP (Up to 12000 LPH

3 HP (Up to 18000 LPH

5 HP (Up to 35000 LPH)

7.5 HP (Up to 72000 LPH)

10 HP (Up to 90000 LPH)

15 HP (Up to 132000 LPH) E

20 HP (Up to 192000 LPH)

25 HP (Up to 228000 LPH

30 HP (Up to 240000 LPH)

35 HP (Up to 276000 LPH

Sewage Pump, Erection charges Erection and giving test and trial for directly coupled sewage pump set on provided foundation. Up to 30 HP

31 HP to 100 HP

101 HP to 200 HP

201 HP to 300 HP

above 300 HP

Supplying and erecting submersible pumpset 0.75kw/ 1HP with 415v 50 cycles ac supply suitable for 100 mm dia borewell . suitable for 10 to 50 LPM Discharge at 70 to 20 M and ( Max Effciency at 52 m. head 30 LPM discharge) & delivery pipe of 32 mm diameter with a neccssary H. type clamp as per specification No. WP. SMP

Suppluing and erecting 3 core pvc. insulated flat flexible submersible cable with Copper Conductor, PVC insulated and PVC sheathed 3core 1.5 sq.mm

3core 2.5 sq.mm

3core 4 sq.mm

3core 6 sq.mm

Providing, suplying & in standard lenghts MDPE Pipes. Conforming to I.S.O. 4427:1996/with necessary jointing material like mechanical connection I.e. thread/insert joint/quick release coupler joint/compresion fitting joint or flanged joint. ...............etc complete. PN-16 SDR - 9 20 mm dia

Providing ISI mark GI pipe with one coupler of following class and dia including all local and central taxces, octroi, inspection charges, transportation to stores etc. complete. IS 1239/2004 15 mm dia Medium

20 mm dia Medium

25 mm dia Medium

32 mm dia Medium

40 mm dia Medium

50 mm dia Medium

65 mm dia Medium

80 mm dia Medium

100 mm dia Medium

125 mm dia Medium

150 mm dia Medium

Lowering, laying, jointing G.I. pipes and specials of following class and dia. including conveyance from stores to site of works, all labour, giving satisfctory hydraulic testing etc. complete. Either underground or in vertical position, as directed by Engineer-in-charge. 15 mm dia Medium

20 mm dia Medium

25 mm dia Medium

32 mm dia Medium

40 mm dia Medium

50 mm dia Medium

65 mm dia Medium

80 mm dia Medium

100 mm dia Medium

125 mm dia Medium

150 mm dia Medium

Providing, supplying ISI mark C.I.D/F. reflux valve (non return valve ) with jointing to pipe work(including all hardware and packing) water works quality with jointing to pipe without bypass arrangement with gunmetal seat excluding c.c. foundation/structural steel supports. For rating PN - 1.6 confirming to IS - 5312: 1984 50 mm dia

65 mm dia

80 mm dia

Lowering, laying and jointing in position following CIDF Reflux valve/ Butterfly valve and Sluice valve including cast of all labour, jointing material including nut bolts and giving satisfactory hydraulic testing etc. complete. 50 mm dia

65 mm dia

80 mm dia

Providing and supplying ISI standard C.I. flanged / S & S specials including all taxes (central and local) railway freight, insurance, unloading from railway wagon, loading into truck, transport to depaRmtental stores/ site unloading stacking etc. complete. D.F.Specials 80 mm to 300 mm dia

Supplying, erecting, testing and commissioning of automatic control panel for three phase , 415 V, A.C. supply, submersible/centrifugal pump set upto 7.5 HP consisting of D.O.L. starter having relay range 9-14 A, S.P.P., combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set for 7.5 HP to 10 HP consisting of D.O.L. starter having relay range 13-21 A, S.P.P., combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set upto 7.5 HP- 10 HP consisting of D.O.L. starter having relay range 28-42 A, S.P.P., combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of automatic control panel for single phase, 230 V, A.C. supply submersible/centrifugal pump set upto 3 HP consisting of D.O.L. starter of suitable relay range, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set upto 20 HP consisting of star delta starter having relay range 13-21 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set upto 20 HP consisting of star delta starter having relay range 28-42 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set upto 30 HP consisting of star delta starter having relay range 30-50 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc .

Supplying, erecting, testing and commissioning of soft starters for three phase, 415 V, A.C. supply water pump upto 15 HP consisting ofRS-485 communication port, compact size & range, internal bypass contactor, 400% max. allowed overload of nominal current, with compatibility with teleservice software "remote drive" on internet, having protection for motor overload, phase sequence, excess start time, phase loss, power circuit fault, supply frequency, communication failure etc. complete.

Supplying, erecting, testing and commissioning of soft starters for three phase 415 V, A.C. supply water pump 25 HP consisting of RS-485 communication port, compact size & range, internal bypass contactor, 400% max. allowed overload of nominal current, with compatibility with teleservice software "remote drive" on internet, having protection for motor overload, phase sequence, excess start time, phase loss, power circuit fault, supply frequency, communication failure etc. complete.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, submersible/centrifugal pump set upto 10 HP consisting of star delta starter having relay range 9-14 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, submersible/centrifugal pump set upto 10- 15 HP consisting of star delta starter having relay range 13-22 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc.

Supplying, erecting, testing and commissioning of float sensor switch for water level controller working on 250 V & rated current 8A, with 2 m wire & high quality of wire & plastic body.

Supplying, erecting, testing and commissioning of directly operated single phasing preventer complete erected and connected to supply to operate in case of single phasing with guarantee for minimum one year.

DOL STARTER- Supplying and erecting DOL starter to operate squirrel cage induction motor working on 380 - 400 V, 3 Ph., 50 Hz., with no volt coil, overload element with necessary material & connected to supply etc. comp. Starter with original sheet steel encloser. Up to 7.5 HP

Up to 10 HP

F.A.S.D. STARTER- Supplying and erecting Fully Automatic Star delta starter to operate squirrel cage induction motor working on 380 - 400 V, 3 Ph., 50 Hz., with no volt coil, overload element and on off push button with necessary material & connected to supply etc. comp. 7.5 HP to 12.5 H.P.

above 12.5 HP to 20 H.P.

above 20 HP to 25 H.P.

above 25 HP to 40 H.P.

Providing structural steel work in single stanctions composed of RSJ chanel etc. with caps, bases, mild steel plates angles, bracket cleats, gusset plates, anchour bolts etc. as per detailed drawing and design or as directed by Engineer-in-charge including cutting, fabricating, hoisting, erecting, fixing, in position making reveted/bolted/welded in connection and one coat of anti corrosive point and over it two coats of oil painting etc. complete.

Earthing for pumping machinery Supplying and erecting earthing with galvanised cast iron earth plate size 60x60x0.6 cm complete with all materials,testing &recording the result as per specification no.EA-EP

Excavation for foundation / pipe trenches in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding back filling, etc. complete. Lift 0-1.5 M.

Excavation for foundation / pipe trenches in Hard murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding back filling, etc. complete. Lift 0-1.5 M.

Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with unplastised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 including all local and central taxes, transportation, freight charges, inspection charges, loading, unloading, conveyance to the depaRmtental stores/ site and stacking the same in closed shed duly protected from sun rays and rains including cost of jointing material i.e. solvent cement, etc.complete (selffit type to be jointed with cement solvent). 63 mm dia. PVC 4 Kg/ cm²

75 mm dia. PVC 4 Kg/ cm²

90 mm dia. PVC 4 Kg/ cm²

110 mm dia. PVC 4 Kg/ cm²

140 mm dia. PVC 4 Kg/ cm²

Lowering, laying and jointing PVC pipes and specials of following class and diameter including cost of conveyance from stores to site of work including cost of all labour, material, except cement solvent, rubber ring, giving satisfactory hydraulic testing as per IS code, etc. complete (with cement solvent joint / ring fit joint). 63 mm dia. PVC 4 Kg/ cm²

75 mm dia. PVC 4 Kg/ cm²

90 mm dia. PVC 4 Kg/ cm²

110 mm dia. PVC 4 Kg/ cm²

140 mm dia. PVC 4 Kg/ cm²

Providing and laying in citu C.C. of of trap / granite/ quartzite/gneiss metal for foundation and bedding including normal dewatering, formwork, compacting and curing, finishing, etc.complete. PCC M -100 For Reinstaining of cement road

Providing and constructing two taps standpost as per type design with excavation 15 cm thick PCC (1:3:6) bedding 20 mm thick PCC (1:2:4) concrete for platform of 1.75 M dia. With side curb and bucket rest 80 mm dia, heavy duty GI pipe central post duly filled therein with C.C. (1:2:4) 5 M long, 20 mm dia. medium G.I. Pipe from point of tapping to standpost additional 20 mm dia G.I. pipe fixed verticaly upto 15 mm dia self closing water taps on brass ferrule etc. complete together with all labour and material charges as per drawing and as directed by Engineer-in-charge when good foundation is available. rate includes draining arrangement by excavating open gutters.

Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete.

Providing,hosting and fixing in position of approved make high density polyethylene UV stabilized conforming to IS 12701 ,water storage tank with necessary connections, testinfg etc complete 9 prior approval of sample by ex. Engineer is necessary before use ) Spect. No. as directed by engineer in charge. for 200 to 1000 lit.

for 1000 to 2000 lit.

Providing fixing 15mm dia screw down bib stop tap of brass including necessory socket union nut complete (PWD CSR 22-23 P.NO. 288 I.NO. 41.40

Providing fixing 20 mm dia screw down bib stop tap of brass including necessory socket union nut complete (PWD CSR 22-23 P.NO. 288 I.NO. 41.41

Providing fixing 25mm dia screw down bib stop tap of brass including necessory socket union nut complete (PWD CSR 22-23 P.NO. 288 I.NO. 41.42

Providing and fixing screwdown 15mmdia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screwdown 20mmdia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screwdown 25mmdia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing screw down for 40 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing screw down for 50 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing screw down for 50 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and laying in trenches dia CPVC PIPE including necessary excavation fitting reffilling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed etc complete for 15 mm dia

for 20 mm dia

for 25 mm dia

for 32 mm dia

for 40 mm dia

for 50 mm dia

For ABove Submersible Pump 30.HP Providing, erecting and giving test of 150 mm dia. submersible pump sets confirming to IS 8034 and motor confirming IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and Motor suitable for working on 415 V± 10%, 3Ph, 50 Hz., A.C. supply, Cable guard, thrust carbon/fibre bearing to accept entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable suction stainer shall also be provided. 3 core, single/double run copper conductor submersible type flat cable 3 Mtr. and 3 pairs of erection clamps. Rates per pump upto 8 stages (as per design) FOR 75 HP

FOR 75HP supply rate should be increased per stage for pump with more than 8 Stage

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 1.50 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 2.0 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 3.0 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 4.0 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 5.0 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 6.0 HP

Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages 7.5HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 5.0 Hp to 7.50 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 7.5 Hp to 10.0 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 10 hp to 15 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 15 HP to 20 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 20 hp To 25 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 25 hp To 35 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 35 hp To 50 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 50 hp To 75 HP

Design Supplying, installing, testing and commissioning of Hybrid Controller for 3 to 100Hp solar Pumping System Compatible to cloudbase (RMS) Dashboard reporting/monitoring and Management monitoring system with FIve Years C.M.C. as per GSDA Circular Dtd. 11/09/2024 Above 75 hp To 100 HP

Please Enable Macros to View BoQ information