REPAIR/MAINT/REPLACEMENT OF WATER SUPPLY DISTRIBUTION PIPE LINE IN THE AREA OF THE AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed.

All as per item No 01 above but 20 mm bore

All as per item No 01 above but 25 mm bore

All as per item No 01 above but 40 mm bore

All as per item No 01 above but 50 mm bore

All as per item No 01 above but 80 mm bore

Supply & Fixing Medium grade steel tubing (wall,ceiling,floors etc) 15 mm bore with and including necessary fitting complete all as specified and directed.

All as per item No 07 above but 20 mm bore

All as per item No 07 above but 25 mm bore

All as per item No 07 above but 40 mm bore

All as per item No 07 above but 50 mm bore

All as per item No 07 above but 80 mm bore

Taking up worn out cast iron water mains (including all fittings) with spigot & socketed ends and lead joints including burning out joints and recovering lead for the 100 mm bore complete all as specified and directed.

All as per item No 13 above but 150 mm bore

Suplying, laying, testing Centrifugally Cast (Spun) Ductile Iron Pressure Pipes with Spigot & Socket end, Class K-7 & conforming to IS: 8329/2000 and amendment No.1, 2 & 3 suitable for (push-on) rubber gasket jointing with centrifugally applied inside cement mortar lining with Portland Slag Cement as per IS: 455:1989 and external Metallic Zinc Coating as per annex A of IS 8329 with finishing layer of Bitumen coating as per Annex C of IS: 8329. The standard lengths of the pipes are 5.50 meter (subject to tolerance as per clause 15.5.1 of IS: 8329:2000). Pursuant to clause 15.5.1 of IS8329 of the 100 mm bore size, complete all as specified and directed.

All as per item No 15 above but 150 mm bore

M&L for rep of water leakage in exsting pipe of 80 mm bore size up to at any location in the area of the AGE E/M Hosp with run lead joint complete all as specified and directed. Note - All Man power, T&P , joint mtrl , excavation up yo 5 mtr lenght , filling etc as required for repair leakge pipe line cost are included in quoted rate by contractor.

All as per item No 17 above but 100 mm nominal bore

All as per item No 17 above but 150 mm nominal bore

Supplying and fixing (in repalceemnt ) of sluice valve class PN-1 heavy duty both ends flanged with steel spindle and check nuts cast iron operating wheel IS-14846 marked of make Upadhayay/ Kirloskar with and including nuts,bolts,washers,gaskets etc and dismantling of old unserviceable sluice valve of the 80 mm bore , PN 1.6 sizes, complete all as specified and directed.

All as per item No 20 above but 100 mm bore , PN 1.6

All as per item No 20 above but 150 mm bore , PN 1.6

S & F ( in repairs) Gun metal gate valve , Class -1,ISI marked complete with iron wheel head, screwed both ends for iron pipe of 15 mm bore sizes complete all as specified and directed.

All as per item No 23 above but 20 mm bore

All as per item No 23 above but 25 mm bore

All as per item No 23 above but 40 mm bore

All as per item No 23 above but 50 mm bore

Cutting of road ( in hard /dense soil) for laying pipe line or repairs to pipes / lead joints etc. of any size upto 1 metre depth and getting out including forming bottom surface to required level or slope and making good of the road as per existing complete all as specified and directed.

Drilling and tapping cast iron/ mild steel water mains ( in position ) for branch connections including supply of GI nipple of medium grade pipe,150mm long of 15 mm bore complete all as specified and directed.

All as per item No 29 above but 20 mm bore

Excavation in trenches not exceeding 1.5 mtr wide not exceeding 1.5 mtr depth in soft/loose soil and getting out for removing/laying of pipe lines complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for construction of brick masonary valve pit of size 90cm x 90cm x 90cm (internal demension) complete with 50x50x6mm angle iron frame, with 3.15mm thick MS cover sheet with hinges, sliding type lifting handle of MS bar 12 mm dia with locking arrangement heavy duty duly welded with angle iron frame complete including necessary excavation and earth work, PCC (1:2:4,) type B-0 (using 12.5mm graded agregate) as in coping, 15mm thick internal plaster in CM (1:4) 75mm thick PCC (1:4:8), type D-2 (using 40mm graded agregate)lean concrete over 75mm thick hard core over rammed earth, flooring shall be 40mm thick PCC (1:2:4) type B-1(using 20mm graded agregate) all steel surfaces shall be painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and shown on drawing No TD/EM/12 complete all as specified and directed.

M&L for construction of brick masonary valve pit of size 120cm x 120cm x 90cm (internal demension) complete with 50x50x6mm angle iron frame, with 3.15mm thick MS cover sheet with hinges, sliding type lifting handle of MS bar 12 mm dia with locking arrangement heavy duty duly welded with angle iron frame complete including necessary excavation and earth work, PCC (1:2:4,) type B-0 (using 12.5mm graded agregate) as in coping, 15mm thick internal plaster in CM (1:4) 75mm thick PCC (1:4:8), type D-2 (using 40mm graded agregate)lean concrete over 75mm thick hard core over rammed earth, flooring shall be 40mm thick PCC (1:2:4) type B-1(using 20mm graded agregate) all steel surfaces shall be painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and shown on drawing No TD/EM/12 complete all as specified and directed.

M & L For Attending complaint of water pipe line leakage/brolen of size upto 150 mm removing broken/ damage/rusted pipe line then after repair/maint /replacement of pipe and refixing same pipe including excavation work returnig filling same with necessary T &P jointig mtrl with gasket/lead socket all as required at the site, complete all as specified and directed.

Ductile Iron specials suitable for spigot and socket end pipes such as bends, pieces, collar, sockets caps and plugs etc., suitable for up to 150mm bore DI pipes complete all as specified and directed.

Cleaning of Over head tank / reservoir of any staging of following capacities by draining out water, removing the silt / mud from inside, cleaning the internal surfaces of wall / ceiling / floors by using wire brushes, removing silt / sludge, complete drying the floor area by cleaning with anti bacterial agent (solution to be prepared in water @ 0.20 Kg of bleaching powder/ washing soda per sqm of internal area) at internal surfaces for making bacterial free, applying two coats of white wash on whole internal surfaces including making necessary writing the details of date of cleaning of over head tank and next due date of cleaning with synthetic enamel white paint over one coat of black painted surface complete all as specified and directed. (a) Capacity of 50000 gallons

Non return valve, 150mm dia bore, flanged and drilled type with complete fixing accessories like nuts, bolts, packing material etc including taking down existing valves complete all as specified and directed.

Non return valve, 100mm dia bore, flanged and drilled type with complete fixing accessories like nuts, bolts, packing material etc including taking down existing valves complete all as specified and directed.

Non return valve, 80mm dia bore, flanged and drilled type with complete fixing accessories like nuts, bolts, packing material etc including taking down existing valves complete all as specified and directed.

Shree Kanth Technologies

M/s ARPIT ENTERPRISES

M/S Nav Jyoti Enterprises