SPL REPAIR TO BLDG NO MES 11 (OR MD ACCN) AND PROVN OF 433 X CEILING FANS (OFFRS JCOs /OR) MD AND SINGLE ACCN OF 100 FD REGT AT ARMY CAMP JAMSHEDPUR UNDER GE RANCHI

Amount

Dismantling AC corrugated /semi corrugated sheets in roof covering complete all as specified and directed.

Dismantling of wall and ceiling boards any thickness including corner fillets complete all as specified and directed.

M&L for preparation of old painted steel & iron surface of any description n exc 10 cm width or girth when connected with other painting or when painted in different tint applying two coats of synthetic enamel paint over on steel surface.complete all as specified and directed.

Ditto- as item above but over 10 cm in width or girth , not otherwise described. complete all as specified and directed.

M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having curled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre incl 2mm dia G.I. ( upto 1200 mm length ) adjusting level to Purlins/ Rafter. Complete all as specified and directed.

M&L for 4mm thick non asbestos designer fibre cement building board of size 600X600 fixed or laid/inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping. Complete all as specified and directed.

S & F Pre- painted galvolume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed..

Demolition of cement concrete (Un reinforced) in ground floors and pavings n. exc 15 CM thickness (below or above ground level). Complete all as specified and directed.

M & L PCC 1:3:6 type C2 , using 20mm graded aggregates as in 75mm thick plinth protection including bitumen joints in 1.0 Mtr centre to centre as required. Complete all as specified and directed.

Taking down cement plaster on brick or stone wall and any other type of wall finishes incl racking out joints hacking for key, scrubbing down with water and removing the debris from site all as directed.

Demolition of Brick work or stone masonry built in cement mortar. Complete all as specified and directed.

M & L Brick work with sub class `B` bricks straight or covered on plan any radius built in cm 1:6. Complete all as specified and directed.

M & L Brick work with sub class `B` bricks straight or covered on plan to any radius in half brick thick wall built in cm 1:4, complete all as specified and directed.

M & L for rendering in cement mortar (1:6) , 15 mm thick on fair faces of brick work / Concrete /stone surfaces finished even & smooth without using extra cement completed all as specified and directed.

M&L for rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:4) with using on wall finishing the surfaces even and smooth without using extra cement. Complete all as specified and directed.

Dismantling steel window and ventilators including guard bar etc complete and removing to MES store all as directed at site. Complete all as specified and directed.

S&F aluminium anodised aluminium window shutter Sliding type with frame of anodised aluminium channel section suitable for sliding aluminium shutters weighing not less than 0.55Kg/M including necessary joining cleats glazing clips rubber packing anodised aluminium shop beading screws with two shutter Including 3.5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F anodised aluminium ventilator shutters fixed or louvered type without sash bar, aluminium section weighting not less than 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and 4 mm thick figured glass fixed in frame etc completed all as specified and directed.

S & F mild steel in framed work such as grills, grating, guard bars welded to steel frames and similar work confirming to Fe 410-O, complete all as specified and directed.

M&L for Cement conc type C-1 (1:3:6) 20mm graded stone aggregate as in bed block of hold fast.

M&L including preparation of new plastered wall surfacesand applying two coats of distemper oil emulsion over plaster of paris putty of 1 mm thickness over chalk whiting omplete all as specified and directed.

M&L including complete removal of existing surfaces and applying two coats of distemper oil emulsion over plaster of paris putty of 1mm thickness over chalk whiting complete all as specified and directed..

M&L Complete removal of existing treatment on wall and applying two coats of cement base paint of any colour over one coat primer all as specified and directed.

Taking down chowkhats or frame n.exc 1.50 Sqm each with shutter (without taking of shutter from framed) complete incl removing from site. Complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 Sqm but n.exc 4 Sqm each with shutter (without taking of shutter from framed) complete incl removing from site. Complete all as specified and directed.

M&L Pressed steel frames 125 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F factory made solid PVC Moulded door shutter 28 to 30 mm thick(stiles) with 2 mm thick prelaminated Moulded PVC sheet polyurethane painted on the front face & 2 mm plain colour PVC sheet on back faces,and with particle board core supplying and fixing in frame at site as per specification and drawing.

S&F Factory made solid panel PVC Skeleton door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;wire gauzed i.e. panel will be of wire gauze,The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S.tubes. The wire gauge shall be stretched to tighten firmly. Complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube S&F in opening all as shown on drawing and specified.

S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or stainless steel wire staples. Complete all as specified and directed.

S&F extruded aluminium alloy butt hinges 100mm size type B-21 all as specified & directed.

S&F 150 mm long aluminum anodized barrel tower bolt extruded section. Complete all as specified and directed.

S&F 150 mm long extruded anodised aluminum alloy handle fabricated type. Complete all as specified and directed.

S&F 300 mm long of bolt Mild steel sliding door bolts,plate type,stove enamelled black,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolt plate and two on staple plate complete all as specified and directed.

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate of Brass complete all as specified and direcetd.

S&F mild steel works as in small articles like hold fasts, conforming to Fe-290 or Fe E-165 all as specified & directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making dismantaled portion in CM (1:3) or cement concrete 1:2:4 Type B-1,Depth of embedded portion of holdfasts not exc.half brick Complete all as specified and directed.

Taking up or down steel tubing and connection of 15 mm bore complete all as specified directed at site.

All as item above but for 20 mm dia bore pipe.

S&F steel tubing and connection tubing in new or old position to walls, ceiling, floors etc including all fitting as socket,elbow,nipple,union etc complete all as directed at site for 15 mm bore all as specified.

All as above item No- 42 but for 20 mm dia

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittins,heads,shoes,bends,swan-necks,etc including removing from site. Complete all as specified and directed.

M&L 110mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

M&L 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

S&F PVC (SWR) bends 110 mm bore of any radius all as specified & directed.

S&F PVC (SWR) bends 75 mm bore of any radius all as specified & directed.

S&F PVC (SWR) junction single (singleT) equal or unequal 110mm bore provided with access door all as specified & directed.

S&F 110 mm bore PVC (SWR) vent cowl. Complete all as specified and directed.

S&F 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement. Complete all as specified and directed.

S&F 110mm dia PVC (SWR)WC connector with lip ring. Complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc. 1.5 mtr deep for foundation in soft/loose soil & getting out. Complete all as specified and directed.

Demolition and breaking up drain pipe 150 mm internal dia of pipe (salt glazed ware, AC or reinforced concrete) set in cement mortor. Complete all as specified and directed.

Returning filling in trenches including spreading, leveling and well ramming with water complete n.exc 25 cm thick in each layer in soft/loose soil. Complete all as specified and directed.

Removing exavated soil n.exc 50 mtr and depositing where directed at a leve n. exc 1.5 mtr above the starting point. Complete all as specified and directed.

M&L precast cement concrete type B-1 (1:2:4) using 20mm graded aggregate as in cover slab, shelves, and similar work set in CM (1:4).complete all as specified and directed.

M&L cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in lean concrete for foundation in drain,manholes etc complete all as specified and directed.

M&L mild steel TMT bars 8 to 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed.

M&L rendering 10mm thick on fair faces of brick or concrete surfaces and finishing the surfaces fair and even without using extra cement in CM (1:4) with W.P.C (W.P.C will be measured and paid separately) complete all as directed at site.

Supply only integral water proofing compound. Complete all as specified and directed.

S&F in repair for 10ltrs capacity flushing cistern PVC low level valve less, symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and 32 mm flush pipe of polyethylene complete all as specified and directed.

S&F in repair 15 mm bore angle/ stop valves , fancy type chromium plated with long shank and cup (conceaeld type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as spfd & directed.

S&F in repair 20mm bore stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed .

S&F in repair, 15mm bore bib taps cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F for 15mm bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down,high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs for shower rose chromium plated with or without swivel joints 75 mm dia complete all as specified and directed.

S&F in repair for vitreous china squatting pan ORRISA Pattern of size 580x 440mm white with integral foot rest and 's'or 'p trap'complete (excluding cistern and flush pipe) with provn of lime concrete including backing joints complete all as directed at site.

S&F for vitrious china wash basin, white flat back size 550 x 400 mm including waste, chain & plug and poreclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for WHB etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waste pipe fitted complete all as specified and directed.

S&F 15 mm pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe.

S&F PVC connection pipe of 15 mm dia and 45 cm long to WHB and flushing cistern complete all as specified and directed.

S&F in repair stainless steel kitchen sink with drainage board 1 mm thick including bedding in cement mortor on to dwarf wall or including fixing centilever brackets over all size 915 mm x 460mm bowl size 410 mm x 330 mm x 160 mm and including 38/40mm dia waiste pipe complete all as specified and directed.

S&F stainless steel utensil rack not less than 1 mm thick of approved quility and fixed in kitchen as directed.

Disconnecting existing tank of capacity exc.250 & n.exc 500 ltrs, setting aside lowering if required for repairs cleaning etc and hoisting if required reconnecting and refixing in position

S&F 500 ltr capacity Rotational moulded polyethylene water storage tank (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. Complete all as specified and directed.

M & L 20 mm thick granite tiles machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen slab.complete all as specified and directed by Engineer-In- Charge. Complete all as specified and directed.

M&L 10 mm thick cement plaster in CM (1:4) for backing of tiles complete all as specified and directed.

M&L coloured glazed ceramic tiles in vertical surface 300x450x7to8mm thick set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18sqm infloor etc;set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

S&F 20mm dia Aluminium powder coated as in golden colour finish draft rod complete all as specified and as approved by EIC.

S&F brass chromium plated decorative bracket fixed to wall . Complete all as specified and directed.

S&F brass CP tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and as directed by Engr-in-charge. Make : Seiko/Parko Complete all as specified and directed.

S&F Glass shelf of size 500mmX125mm consisting sheet glass with CP brackets and CP frame Size 500mm long complete.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc.Removing materials to store in safe custody or for taking credit and making good distrubed surfaces of walls, floors etc Complete all as specified and directed.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated and FR multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) FRLS grade drawn in and including PVC concealed conduit not less than 20mm size and fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.60 mm covered with 3.00 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators complete including 1.0 sqmm copper stranded earth wire for all as specified for the following :-

One light point controlled by one switch.

One fan point controlled by one switch.

One bell point controlled by one switch.

One socket outlet 3 pin 5 Amp controlled by one switch on the same board.

One socket outlet 3 pin 5 Amp controlled by one switch on indepdendent board.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) FRLS grade drawn in and including PVC concealed conduit not less than 20mm size and fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.60 mm covered with 3.0 mm thick phenolic laminated white sheet cover for one 6 Pin 15 Amp socket outlet controlled by one switch on independent board.Incl. 1.5 Sq mm copper conductor earth wire and connected to common earth dolly on independent board. Complete all as specified and directed.

Material and labour for submain wiring alongwith earth continuity conductor with PVC insulated FR multistranded copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into New concealded conduit of nominal size 6 sqmm copper conductor as earth continuity. (Note- Locations where concealded conduit will be found damaged or submain wiring requires relocation, it will be done by laying new PVC conduit and making it concealded. Cost of conduit is included in this item. Complete all as specified and directed.

Supplying and fixing angle holder, insulated polycabonate body with back plate complete.

Supplying and fixing switch piano flush button single pole one way 5/6 amp complete.

Supplying and fixing switch socket combination two in one 5 and 15 Amps multipurpose flush type universal 240Volts. Make - Anchor / Leader / SSK as approved.

Supplying and fixing socket outlet 2 in 1, 5 pin, 5/6 amp, flush type complete.

Taking down carefully aluminium submain wiring with wooden battens/ PVC suface conduit and making good disturbed surfaces completed

Supplying and fixing ceiling rose 65 x 50 mm three terminals complete.

Taking down U/S fan regulator and Supplying and fixing hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete all as specified and directed.

Supplying and fixing integrated LED Bulb 9 watt complete. Make - Philips or Havells or Syska as approved by GE.

S&F LED tube light fitting 1x20/18 watt 230 Volt box type housing extruded aluminium heat sink, driver unit , etc complete with all accessories internally pre-wired and inncluding connecting up with twin core twisted flexible copper conductor cable with suitable size .Cat No-LHEXBHP7IN1W018 of Havells or /Bajaj/Philips

Supplying and fixing LED bulk head fitting 1x 9 watt including connection with PVC insulated flexible flat twin core multi stranded copper conductor cable 0.5 sqmm as required.

Supplying and fixing powder coated, CRCA steel sheet MCB distribution board double door (minimum thickness 1.2 mm & constructed as per IS : 8623), degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces etc as required of following ratings & ways:-

SPN, 240 volts, 6 ways.

SPN, 240 volts, 8 ways

Taking down U/S MCBs/ELCBs with incoming and outgoing controls any make, any capacity after disconnecting complete all as specified and directed.

S&F MCB SPN 6A to 40A 240V 9KA

S&F MCB SP 6A to 32A 240V 9KA

S&F Exhaust fan 300 MM sweep including cutting and chesing ,making hole for fixing complete.model no-Turbo force of Havells/ equivalent to Usha/Khaitan

S&F Ceiling fan 1200mm sweep 5 star power in put 43 watts, Speed 330 RPM including taking down old ceiling fan and deposite to E/M store yard. model no-Fusion -50 of Havells equivalent to Bajaj/ Usha

M&L Bell push , flush type , 5 Amp complete all as specified and directed.

S&F Bell , AC 230 Volts single pole complete all as specified and directed.

M&L for point wiring with 1.5 sqmm single core PVC insulated cable 1100 volts grade multistranded copper conductor drawn through PVC casing and capping with all accessories such as screws, plastic gutties, etc fixed to wall/roofs/ceiling etc and incl provision of 1.5 sqmm PVC insulated and unsheathed copper conductor as earth continuity conductor and connected to common earth dolly including fabricated steel terminal box made out of 1.6mm thick MS Sheet concealed in the wall with 3mm thick laminated sheet top cover for mouting the switches, socket outlets, fan regulators etc all as specified and directed by Engr-in-charge for following:-

One fan point controlled by one switch.

Supply & Fix ceiling fans, complete with three balde, down rod, accessories 230 volts, 1200 mm sweep with squirrel case induction motor.

UPENDRA KUMAR SINGH

M/S AJAY KUMAR SINGH