Renovation and Interior Fit out work of SIDBI Branch office at Varachha

Sr.No Description DSR Amount Non- DSR Amount

1 Civil & Interior Work 6,83,389.29 17,97,627.27

2 Electrical Work 5,95,246.70 495702.00

5 Fire Fighting Work 1,72,539.00 26424.00

7 Fire Alarm & AP System 77,538.00 14500.00

8 Furniture Work 1845970

9 Lighting Work 1,04,772.00

11 Grand Total 75,39,050.00

11 Grand Total 75,39,050.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

1 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In

1.01 MR Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with metre 200.00 280.00 56,000.00

Rubber/ PVC Jointers and Gasket.

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved design & Pattern as per

architects approval & Instructions

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile carpet

tiles/Plank. The carpet shall have sufficient gauge (1/10 ~ 1/12) with sufficient stitches (10~13) per inch.

1.03 MR The carpet shall be solution dyed fibre content or with injection printing technology. The carpet shall sq m 20.00 1650.00 33,000.00

have the pile height ranging from (2.0 ~ 3.0) mm with average density higher than 4500 Oz/

cubic yard. The total thickness of the carpet tile shall also range from (5.5 ~ 6.0) mm.

LAMINATED WOODEN FLOORING Providing and laying 8.3mm thick AC5 grade laminate wooden

flooring having good castor chair and furniture resistance strength. Plank dimension to be

1215x195x8.3mm with valinge clock locking system and wax coating for better sound resistance.

Impact and abrasion resistance to be of high grade having class EN 13329. The flooring shall be laid

1.04 MR with 2mm thick underlay and PVC sheet and prevent against moisture and foot taping sound. The item sq m 34.00 1770.00 60,180.00

also includes the skirting and any other profiles required for proper installation.or its equivalent

specifications or as per the selection of client and items shall be complete in all respects. or its

equivalent specifications/ size as per the site requirement or as per the selection of client and items

shall be complete in all respects.

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with

zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with

2.01 12.45 connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter

of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry

wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both

sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of painting with

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having noise reduction co-

efficient of 0.7, Density of 100 kg / m3, and Humidity resistance of 95% to be laid on exposed grid system

with white wrap comprising main runner 3.00 mm x 24mm web height cross tee 1.2 mtrs x 24 mm web

height and 0.6 mtrs x 24 mm web height. The wall angle shall be 3.0 mtrs.

3 PARTITIONS AND WALL CLADDING

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of Aluminium frame

and required board, frame work made of Aluminium section made of 50x25 mm , consisting of floor

and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm

length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide

having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges

of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable

MR anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of

boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at

the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using

metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm),

joint finisher as per manufacture's specification and direction of engineer in charge all complete.(Cost

of Aluminium framing 600X600mm Paid saperately)

Paneling with 11- 12 mm thick HDHMR board to IS: 5509 sq m 90.00 2,414.28 217285.2863

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of Aluminium frame

and required board, frame work made of Aluminium section made of 50x25 mm , consisting of floor

and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm

length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide

having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges

of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable

MR anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of

boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at

the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using

metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm),

joint finisher as per manufacture's specification and direction of engineer in charge all complete.(Cost

of Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 sq m 70.00 3450.00 241500

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing Plywood

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring

type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete

as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold

fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 0.25 142949.7 35788.89

Providing and fixing partition top beading 80x12 mm, including cutting, shaping, adhesive/fastener

MR fixing, edge finishing, surface preparation, and applying polish with matching finish, complete in all Rmtr 20 225 4500

respects as per site requirement and engineer-in-charge directions.

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS:

8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh

screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per

directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3

ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sq m 12 2,392.65 28711.80

Providing and applying panelling/partition with matching colour groove finish and polishing, including

all materials, labour, surface preparation, fixing accessories, edge finishing, sanding, colour matching,

groove cutting, polishing coats, and complete finishing as per site requirement and engineer-in-charge

Providing and fixing aluminium extruded section body tubular type universal HS 3000 Slimline

Concealed Door Closer (having brand logo with ISi, IS : 3564,embossed on the body, door weight upto

36 kg to 80 kg and door widthfrom 701 mm to 1000 mm), with double speed adjustment with necessary

accessories and screws etc. complete

Providing and fixing aluminium sub-frame made from aluminium section 50 mm × 25 mm × 1.5 mm

thick, including cutting, fabrication, alignment and fixing in position for partition/paneling works. The

job includes all necessary screws, fasteners, rawl plugs, spacers and other accessories required for

proper installation. Complete as per drawing, specification and direction of the engineer-in-charge.

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic AC 10 as per

IS : 1868 ), transparent or dyed to required colour or shade, complete:

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with

necessary screws, etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123 with Roses &

MR Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS forend, SS strike plate and EP EACH 6 2,650.00 15,900.00

Cylinder for all flush doors.

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and designs as per

engineer in charge

Providing and fixing minimium 70-90 kg capacity flooor spring for Doors approved make and designs

as per engineer in charge

MR Providing and fixing Glass door lock approved make and designs as per engineer in charge EACH 5 1,680.00 8,400.00

MR Providing and fixing Glass Big -L approved make and designs as per engineer in charge each 2 2,250.00 4,500.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare

the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

13.83 Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less

than 50 grams/ litre

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give

an even shade :

13.99.1 One or more coats on old work. sq m 40 102.80 4112.00

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

BLINDS Providing & supplying of Window Blinds as per the approved sample in required shade

and style consisting, of ZEBRA BLINDS comprising of optima screen Fabric comprising of 22% polyester,

78% PVC, Fabric weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18- 19/cm, having

fire resistance standard – NFPA 701-89 small testing ISO- 5659-2 .Thetear resistance should be complying

to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe

installation, moulded plastic with steel spring support and inserted into the tube end. It shall be driven

by a ball chain pulley with ball chain and can be positioned at right side or left hand side of the Shade.

The Shade when lowering or raising, shall be automatically locked in position upon release of the ball

chain by means of a built in friction lock.Universal clutch for left and right hand operation.Chain Gear

M.R. Ratio of 1.75:1. The END PLUG shall be molded of plastic witha steel location pin.The plug shall be sq m 16 1,650.00 26400

inserted into the tube end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS

shall be of coated steel & provided with covers and used in right hand or left hand positions

differentiated by the acceptance of the of the rectangular drive unit support or the round idler plug

pin. Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of 80mm.The ROLLER TUBE shall

be of extruded aluminum with 37mm internal diameter & skin thickness of 1mm and shall incorporate a

key way integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom

made up of powder coated steel. The BALL CHAIN shall be 2mm diameter cord with 4.5mm diameter

acetal balls moulded co-axially to it on 6mm pitch to form an endless ball chain. It is used for raising

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as approval of the

Architect. (Only film surface area shall be measured and paid).

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate of matching, Shutters

to be fixed to a frame. Rigidly fixed on both sides and top finshed in laminate. No internal carcass

MR required. All Hinges of hettich or equivalent. Internal Surface of the shutter in balancing white laminate. sq m 5 11,500.00 57500

All shutters to be provided with Stainless steel louvers at the top and bottom of the shutter as per

the site requirements and instrcution of the Engineer In charge.

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per Direction of Engineer in

One Way vision Film :-Providing and fixing scotchcal over glass surface as approval of the Architect.

(Only film surface area shall be measured and paid).

MR Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded Letter as per design Sft 84 1350.00 113400

Providing and fixing pelmets to house projection screen / Blinds made of 19 mm thick commercial ply,

having clear internal dimensions as 150/200 x 200/250mm, finished in approved laminate on all

MR exposed surfaces from all external surfaces and balancing laminate on all internal surfaces, supported RMTR 4 1450.00 5800

from RCC ceiling slab by necessary framework, giving additional supports in MS angles etc. complete.

All exposed edges to be finished in 6mm thick TW beading and finished in approved colour.

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I.

frame and required board, including providing and fixing of frame work made of special

section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side

inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and

0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with

9.105 nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm

and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both

ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon

plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S.

fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at

the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for

board as per manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum

(GRG) plaster board conforming to IS: 2095:

Add labour cess @0.973 as per CPWD circular 6,63,484.75

Add CPWD cost index @103 on DSR civil 2023 6,83,389.29

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

1.10 surface/ recessed medium class PVC conduit, with modular switch,

A.1 modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with1.5 sq.mm FRLS PVC insulated

1.55 copper conductor single core cable in surface / recessed PVC conduit,

and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC

conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor

single core cable for loop earthing as required.

Supplying and fixing following modular switch/socket on the existing

1.24 modular plate & switch box including connections but excluding modular

plate etc. a srequired.

1.24.4 3 pin 5/6 amp socket outlet Each 50 122.00 6100.00

1.24.5 6 pin 15/16 amp socket outlet Each 14 197.00 2758.00

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supplying and fixing modular blanking plate on the existing modular plate

& switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular

base & cover plate on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the

1.14 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 210 233.00 48930.00

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 320 275.00 88000.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 439.00 8780.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 40 1365.00 54600.00

Supplying and making end termination with brass compression gland and

9.1 aluminium lugs for following size of PVC insulated and PVC sheathed/

C.1 XLPE aluminium conductor cable of 1.1 KV grade as required.

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554Aluminium Conductor Cables :

C.2 Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium

conductor armoured cable of 1.1KV grade conforming to IS:7098 part-

1/IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 95 Sqmm XLPE cable RM 10 864.00 8640.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 10 378.00 3780.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE

C.3 MR insulated Copper conductor armoured cable of 1.1 KV grade

conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 40 1446.00 57840.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 10 2253.00 22530.00

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

D.2 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the

2.13 existing MCB DB complete with connections, testing and commissioning

etc. as required.

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/recess, complete

2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

D.4 interconnections, powder painted including earthing etc. as required.

(But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 2 9081.00 18162.00

Providing and fixing 400mm wall mounted oscillating fan, heavy-duty

type, 230V, 50Hz, single phase, with three-speed control regulator,

complete with suitable mounting brackets, clamps, bolts, nuts, and

MR necessary wiring connections from the nearest point using 1.5 sq.mm Each 5 3950.00 19750.00

copper flexible wire, including testing and commissioning at site,

complete as required.( Make: Havells/Cromton/Usha/Bajaj asapproved

by ingineer-in-charge)

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper braid

and protected with PVC sheath in the exisitng surface/recessed steel/

PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong

1.21 with accessories in surface/ recess including cutting the wall and making

good the same incase of recessed conduit as required

Supplying and Installation of following size perforated of painting with

powder coating M.S. cable trays of perforation of not more than 17.5%

E.13 4.1 in convinient sections, joined with connectors suspended from the cieling

with MS suspenders including bolts and nuts painting suspenders etc as

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 8 1137.00 9096.00

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 metre long etc.

with charcoal/coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess

for connections etc. As required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

Supply, Installation, Testing and Commissiong of 10 KVA True Online

Double Conversion UPS 3Phase Input - 3Phase Output in IGBT Based

Rectifier and IGBT Based Inverter 42ah Batteries:12 V, SMF

Amararaja/Exide with minimum VAH capacity of 8064 suitable for 30

MR minutes backup with each ups Along with Accessories Rack, Interlinks, Nos 1 365000 365000

SFU, Parallel Kit, DC Cable Upto 5 Meters complete in all respect as per

the directions of the engineer in charge. UPS should have availability of

Input /Output isolator, Inbuilt manual bypass along with phase sequence

corrector. UPS Efficiency shall not be less than 94% from 25% to 100% Load

Total of Electrical items 575345 495702

Add GST factor @1.0633 on DSR items 611764.34

Add CPWD labour cess factor @0.973 595246.70

Total Amount 595246.70 495702.00

Total Amount 595246.70 495702.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling /heating having

100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two

compressors (with individual separate PCB) for above 14HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent,

vibration Isolators with suitable foundation etc. complete as required. To have better

efficiency condenser fan shall be capable to operate at different speed with respect to load.

The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD

Specifications and work even at 50°C ambient temperature without tripping. The system shall

7.3 be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable

to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall

be filled with first charge of the refrigerant and ready for use as required. The condenser should

be coated with a hydrophilic film to prevent water accumulation on the surface of the heat

exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving

overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the

unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below

and complete as per CPWD specification, connections, inter connections etc. as required. (For

capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super

ECSBC Building)

2.0 INDOOR UNIT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre- filter,

fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

supports, vibration Isolation, Corded remote control etc., suitable for operation on single

phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down

upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to

adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will

be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be

same as of Outdoor)

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Supply, Installation, Testing and Commissioning of following minimum capacity High wall

type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain

pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC

supply, complete as required. The Indoor units must shut down upon receiving a singal from the

BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions

of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing

of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

3 I7.14.1 6.4 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 40.00 256.00 10,240.00

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 40.00 346.00 13,840.00

3.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 40.00 487.00 19,480.00

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 30.00 615.00 18,450.00

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 739.00 22,170.00

3.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 1,157.00 34,710.00

3.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,286.00 25,720.00

3.13 7.13.1 Indoor Units (y-joint) Each 7 4535 31,745.00

3.14 7.13.2 Outdoor Multi Units Each 1 8098 8,098.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe, complete with fittings, supports, U

trap arrangement, Clean Plug with 6mm nitrile insulation and accessories as per specifications,

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in

suitable conduits between indoor and outdoor unit.

6 MR Supply & Fixing IP55 Base Outdoor MCB Box with in 1 Nos 65 amp RCCB Nos 1 14650 14,650.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

7 MR Supply and Fixing MS Base Frame for VRV Outdoor Stand as per requirement of Size L.S 1 20500 20500

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

conductors for Connectivity of Hub room to End Point.High Speed

Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

2 MR cable termination at Rack Side. Keystone Unshielded Outlet, Nos. 40 359.00 14360

Supply, Installtion, Testing and Comissioning of I/O port for CAT6

3 MR cable termination at Rack Side end Redantant . Keystone Nos. 40 359.00 14360

Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2

Mtr (7 feet) for information outlet (I/O) to end user Redantant

device connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord

Yellow, LSZH, C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2

Mtr (7 feet) for information outlet (I/O) to Rack End Redantant

device connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord

Yellow, LSZH, C6, 2M (Yellow)

Supply, Installtion, Testing and Comissioning of 24 port Loaded

6 MR Angled Staggred Jack Panel for CAT6 cable termination at rack Nos. 3 6500.00 19500

end. Data Active Redandant

SITC of 04 core OM3 Multimode fiber orange color 50/125,

minimum bending radius 15x OD

8 MR SITC of 24U Rack Each 1 34,500.00 34500

Digitally signed by AMIT

S NO Description UOM Qty Rate DSR Amount

Supply instllation testing and commissioning of Access Switch of 24

x 1G POE+, 4 x SFP+ , 370W PoE, Switching Capacity of switch is of

176 Gbps having Forwarding performance (64-byte packet size):

130 Mpps, Secure Shell (SSH), as per approved Brand

B 200 Pair MDF Box

1 MR 200 Pair MDF Box with mounting Frame Nos. 1 11666.00 11666

2 MR 10 Pair Krone Module Nos. 1 900.00 900

3 MR 25 Pair Riser Cable Mtr. 5 750.00 3750

Add GST factor @1.0633 on DSR items 145459.44

Add CPWD labour cess factor @0.973 141532.04

Total Amount 141532.04 305011.00

Total Amount 141532.04 305011.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No 2022/ DESCRIPTION QTY UNIT RATE

DSR (INR) NON-DSR

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming

to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers,

18.7 nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of

2 rating 68 degree centigrade with required accessories :

18.21.1 Pendant type 20 Each 522.00 10440.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of

stainless steel complete with 15 NPT on reducer thread with maximum working

pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT

male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer,

3 nipple, 2 side brackets, center bracket, stockbar of following sizes complete as

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all

accessories as per manufacturer's specifications.

a) MR CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12070.00 12070.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 2 NOS 2740.00 5480.00

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). 2 NOS 4437 8874.00

Add GST factor @1.0633 on DSR items 177326.54

Digitally signed by AMIT

Add CPWD labour cess factor @0.973 172538.72

Total Amount 172539.00 26424.00

Total Amount 172539.00 26424.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

A. CCTV DSR NDSR

Supply, Installation, Testing & Commissioning of 2MP IR IP H.265

Vandal Proof Dome camera with 2.8 to 12mm Motorised Lens,Smart

IR, up to 30M IR distance,Up to 120 dB WDR (Wide Dynamic

Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal

Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video

Compression H.265+, H.265, H.264, MJPEG,Behavior Detection

Supply, installation testing and commissioning of Network Video

recorder Linux based to manage and control all the cameras from

2 MR control room. Software shall support maximum 16 channel with Nos 1 34500.00 34500.00

joystick controller. 256Mbps Bit Rate Input Max(up to 32-ch IP video), 2

SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with 1x4TB i.e. 4TB HDD inside

Supply Installation Testing & Commissioning of 32 inch Full HD LED

monitor including wall mount brackets/ clamps/ desk mounting stand.

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors

4 for Connectivity of Hub room to End Point.High Speed Gigabit Ethernet METRE 350 57.00 19950.00 0.00

U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

5 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 2 3500.00 7000.00

Add GST factor @1.0633 on DSR items 21212.835

Add CPWD labour cess factor @0.973 20640.09

Total Amount 20640.09 112500.00

Total Amount 20640.09 112500.00

Digitally signed by AMIT

FIRE ALARM SYSTEM WORKS

S.NO. DESCRIPTION UNIT Qty RATE

NO. AMOUNT Amount

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of FIRE PANEL

upto 2 zone complete as required.

Supplying, installation, testing & commissioning of smoke detector

c) 17.1.2 with built in LED and Mounting base complete withb all No. 18.00 1153.00 20754.00

Connections etc. as required.

Supplying, installation, testing & commissioning of manual call

boxes of MS construction in Surface/ Recess with Stainless Steel

chain & hammer Assembly complete with glass and push

button etc. as Required.

Supplying, installation, testing & commissioning of response

d) 17.1.5 indicator on surface/recessed MS Box having two LED, metallic No. 10.00 196.00 1960.00

cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm

Sounder with Facility to make annoucement, mountedc in M.S

e) 17.1.6 Box (16 SWG) with Hinged cover plate & Suitable for operation No. 2.00 557.00 1114.00

with Amplifier i/c line matching transformer etc complete as

CABLING & WIRING

Supplying & laying of 2x1.5 sqmm fire survival alarm armoured

cable, 600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & ERLS outer sheath

complete as required.

Add GST factor @1.0633 on DSR items 79690.08

Add CPWD labour cess factor @0.973 77538.45

Total Amount 77538.00 14500.00

Total Amount 77538.00 14500.00

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

BO Incharge banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

Table 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board. Provision

of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement.Main

Table Dimension (L)2100mm X (D) 1000mm X (H)750mm overall Side Runer Dimension (L)900mm X

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non working

2 Back Storage Nos 1.00 26,500 26,500.00

edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

3 with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for Nos 1.00 15,000 15,000.00

extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

BO Visitor Back Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

Chair Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are made

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per

requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern,

Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat

cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75

inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per

requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern,

Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat

cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75

inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Reception Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

Corner/ Cofee X (D)450mm X (H)450mm

Supplying, and placing in position of Centre Table as per approved design Dimension(L)1150mm X

8 Centre Table Nos 1.00 16,500 16,500.00

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

AGM/Manager banding. The table shall be provisioned with Side unit of overall size: 1500mm(L) x 450mm(D) x

Table 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board. Provision

of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement.

Main Table Dimension (L)1500mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

10 AGM Chair tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- Nos 3.00 10,500 31,500.00

0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall

be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The

backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Medium Back lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

11 chair AGM with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 6.00 8,500 51,000.00

Cabin have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non working

12 Back Storage Nos 3.00 24,500 73,500.00

edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension

Supplying and placing in position of conference table of required size as per image/ Layout drawing. The

work surface top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC

Conference edge banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are

Table made out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire

carrier should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a

provision of 6 module flip top box & metal raceway for wire flow.

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

14 tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- Nos 1.00 10,500 10,500.00

0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall

be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The

backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Medium Back lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

15 chair Confrence with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall Nos 8.00 8,500 68,000.00

room have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3)

The backrest has a foam of 28kg/m3.

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm x

25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel

fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

Linear wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

Workstation workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass divider

rest on the "D" brackets on the table top between opposite seatings. All working or non working edges

shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side Top

with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht. 1200mm,

Double Raceway systems Skirting label and below the table top . lower tile both side laminated and

Modular upper tile inside side fabric, White Board and white Tinted Glass . With Side Top Size 900W x 400D x

Workstation 750H 25mm thick Gabel end 18mm thick MDF board., and 3Drawer top supported Pedestal unit

Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty

White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-

Munshel Gray. and White Tinted Glass

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of

density 30-35 (+/- 2kg /m3) The backrest has a foam of 28kg/m3.

Providing & Installation of Pantry table of size 1.2m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

19 Pantry Table Nos 1.00 26,500 26,500.00

Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Reception table of size .75Dia X 0.75m (ht) made out of 19mm thk.

Reception Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

21 Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC Nos 4.00 4,500 18,000.00

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

Openable of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

Shutter storage pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

and suitable lock. All exposed area PVC edge lipping

Pantry Under Pantry Under Counter Storage, made with HDHMR board finished with laminate on all exposed surfaces.

23.0 Counter Unit depth: 600mm. All edges shall be finished with matching edge banding. Includes shutters, shelves, Sqm 4.00 12,500.00 50000

Storage hardware (hinges, handles), and necessary fittings complete in all respects.

Pantry/ Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade conforming to E1

Workstation norms, with unit depth of 400mm. All exposed edges finished with 2mm PVC edge banding using

Overhead hotmelt EVA glue. Includes shutters, shelves, and necessary hardware and fittings, complete in all

Storage respects.

Total Amount 18,45,970.00

Total Amount 18,45,970.00

Digitally signed by AMIT

Description Unit Qty. Rate Amount

LED Down lighter (COB Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying of LED Recessed/ surface

Down lighter (Round/ square/ Rectangular) COB Type of following body material and construction as per IS : 10322

with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60

hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be

below 5%), life time (LED, Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial

Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard

Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and

Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Word Mark

/Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm

FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-

in-Charge as per equirement. (Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim with

Aluminium Reflector 12 -15 watt

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying of Panel light 2x2 ft., of following body

material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge

protection of 2.5 KV with Short & Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000

Burning Hours with, 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As

per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than

4258 the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate(T.C.). Manufactures Nos 30 2700.00 81000

Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with

1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5

year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C). Powder coated die cast/Extruded aluminium Body (Thickness >

Total of Electrical items 104772.00

Digitally signed by AMIT