GE (N) P/TOKEN- 21 OF 2025-2026 SPL REPAIR OF TWO X ROOMS BLDG NO 01 (OASIS BLOCK) AT SCOM IN THE AREA OF AGE B/R (CENTRAL) UNDER GE (N) PUNE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but notbacking), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Demolition of cement concrete(un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

Cutting holes in stone walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed

Cutting chases in stone walls , pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; making good, cutting exceeding 20cm girth complete all as specified and directed

S&F MS rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed

Formwork to suspended slabs such as roof slabs, landing and similar work not exc 200 mm thick complete all as specified and directed

M&L for RCC M-25 (nominal mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed

M&L for coloured vitrified double charge tiles 10mm thick (square/rectangular) area of each tile exc 0.42sqm but not exc 1.00 sqm as laid in any pattern/design in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed

Ditto as item above but in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding in CM 1:4 complete all as specified and directed

M&L glazed ceramic coloured cladding tiles including highlighter of size 600 x 300 x 7-8 mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick backing coat in cement mortar 1:4 complete, all as specified.

M&L Granite (of any type), 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform,WHB plateform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade including 10mm thick backing of cement plaster in CM 1:3 complete all as specified and directed

M&L for machine cut 20-25mm thick polished cudappah stone slab as in shelves, partitions, cooking platform below granite stone and like including necessary jointing and pointing in cement mortar and making good to disturbed surface including dismantling of existing stone slab complete all as specified and directed

Taking down chowkats or frames not exc. 1.5 sq. m each with shutters of any description (without taking off shutters from the frames) complete all as specified and directed

All as per item No 16 above but exc. 1.5 sq.m but n exc 4 sqm each complete all as specified and directed

S&F Factory made 100 % solid wood plastic composite(WPC) door frame, single rebate 90 mm x 45 mm made from wood plastic composite (Single extruded process) material with density 780 Kg/ Cum and complete all as specified and directed. NOTE: During fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

S&F 1st class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 1st class hardwood 30 mm thick Glazed and skeleton windows shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 1st class hardwood 35 mm thick Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 1st class hardwood 40 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F factory Made Solid PVC Molded shutter of 28 to 30 mm thick (stiles), consisting of frame made up of MS tube of size 40mm X 20mm (19 gauge) for top, bottom rail, and in stiles rail, with 2, 4, or 6 raised panel design with 5mm thick Moulded Prelam PVC Sheet on the front face & 5mm thick Prelam PVC sheet on back face. Inside core shall be of PVC solid board of 20 mm thick. Door shall be provided with 20 mm thick PVC lipping all around the edges, fixing in frame at site complete all as specified and directed Note : All screws shall be self tapping and length of Screw not less than 50 mm.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples fixed on wood or steel frame complete all as specified & directed.

S&F 4mm thick plain sheet glass ordinary quality in any type of frames and glazing with beading in square n. exc. 0.5 Sqm in each pane complete all as specifed and directed

S&F brass butt hinges medium weight 100mm all as specified and directed.

S&F for floor door stopper of brass body and tongue not less than 150 mm long, anodised with hard drawn steel spring all as specified and as directed.

S&F for aluminium powder coated three track sliding window with two glazed shutters with 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make complete all as specified and directed. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

S&F 18 mm thick UV coated exterior grade MDF board duly edge banded with 0.8 mm thick PVC taping, fitting of shutters shall be fixed as approved by GE suitable for cup board etc. includinguding taking down with existing one complete all as specified and directed. Make: Action tesa, Century, Kitply

S&F for HDHMR (high density high moisture resistance) board manufactured with hard wood, prelaminated both sides white in colour 18 mm thick water resistant, teRMite resistant, duly edge banded with PVC taping 0.8 mm thick, cut to shape & size as in cupboards/shelves/cabinets and similar work etc includinguding taking down with existing one complete all as specified and directed. Make: Action tesa, Century, Kitply

S&F auto closing hinges with stainless steel screws including taking down with existing one complete all as directed

S & F continuous (piano) hinges, stainless steel, width of flaps (when open) in 20mm, 0.8mm thickness complete all as specified & directed.

S&F in repair drapery curtain rod of brass body 20mm/25mm dia complete with brass bracket and side caps fixed in position by drilling holes in walls and fixed the brackers with rawl plug and brass/decorative screws compete all as specified.

S&F in repair bracket for brass curtain rod of 20mm/25mm dia fixed with rawl plug and brass/decorative screw compete all as specified.

S&F brass body hasp and staple of 100 mm size including bolt to hinge plate fixed with Self Tapping screws complete all as specifed and directed by Engr-in-Charge

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specifed and directed

M&L for Fly ash brick work using old size bricks, straight or curved on plan exc 6m mean radius built in cm 1:6 complete all as specifed and directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specifed and directed

M & L for rendering 10mm thick in CM (1:6) on brick masonry internal surfaces of walls finished even and smooth without using extra cement complete all as specifed and directed

M&L for preparation of new plastered surfaces of wall and applying two coats of plastic emulsion of any tint over a coat of primer over a 1 to 1.5 mm thick layer of wall care putty complete all as specified.

M&L for 15mm thick cement plaster in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement upto 12.0m height of Bldg with using @ 2% WPC on cement complete all as specified. (Note: WPC shall be measured in separately).

M&L for preparation of new plastered surfaces and applying two coats of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent brand of Berger/Shalimar) over a coat of primer on wall complete all as specified and as directed by Engineer-in-charge. NOTE: This item of work is to be operated upto 10m Building Height.

M&L for preparation of old wall surfaces and applying two coats of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent brand of Berger/Shalimar) over one coat of primer to including complete removal of existing treatment complete all as specified and as directed by Engineer-in-charge. NOTE: This item of work is to be operated upto 10m Building Height.

S&F 15 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed including taking down of existing complete to walls and ceilings or laid in floors complete all as specified and as directed

S&F 20 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed including taking down of existing complete to walls and ceilings or laid in floors complete all as specified and as directed

S&F in repair for vitreous china premium 1st quality jaguar of size 390x645x845 mm UF soft close seat floor mounted wash down water closet EWC white/ivory/off white incl flush cistern fittings, health faucet alongwith two way bib cock and accessaries complete all as specified Make : Jaguar Model No ONS-WHT-10753NS250UFSMZ or equivalent

S&F in repair vitreous china in white colour table top basin (self-rimming) rectangular shape of size 530mm x 420mm x 140 mm fixed in position incl waste coupling and PVC wate pipe, 32 mm dia complete make : Jaquar Cat part No-JDS-WHT-25907N or equivalent.

S&F in repair 5 mm thick bevelled edge looking mirror of size 1.2 m x 0.60 m fixed to wall with SS studs with cap head complete all as specified and directed.

S&F pillar taps suitable for 15 mm bore pipe long body fancy type brass CP with Capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified.: Make: Jaquar Cat part No-FON-40011 or equivalent. as approved by GE

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed. Make:Paryag/Polytuf

S&F bib cock long body quarter turn suitable for 15mm bore pipe long body with flange fancy type brass CP with, screwed for iron pipe or brass ferrule complete all as specified. Make: Jaquar Cat part No-ARI-39037 or equivalent. as approved by GE

S&F two way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as specified. Make: Jaquar Cat part No-ARI-39041 or equivalent. as approved by GE

S&F hand shower (health faucet) of cast copper alloy chromium plated with 8mm dia, 1.2m long flexible tube and wall hook complete all as specified and directed by Engr-in-charge. Make : CERA -F8030103 or of equivalent .

S&F Stop valve/ Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed. Make: Jaquar Cat part No-ARI-39053 or equivalent. as approved by GE

S & F brass chromium plated soap dish, fixed to wall with CP brass screws, all as specified and directed. Make: Jaquar Cat part No-AKP-35731P or equivalent. as approved by GE

S & F Brass Chromium plated 600 mm long towel rail all as specified and directed. Make: Jaquar Cat part No-AKP-35711PS or equivalent. as approved by GE

S&F brass chromium plated towel ring all as specified and directed. Make: Jaquar Cat part No-AKP-35721P or equivalent. as approved by GE

S&F Toilet paper holder of stainless steel, all as specified and directed. Make: Jaquar Cat part No-AKP-35751P or equivalent. as approved by GE

S&F in repirs wall mixer brass chromium plated quarter turn 3 in 1 with provision for both over head and hand shower bend pipe on upper side connecting legs and wall Flanges suitable for fixing with GI pipes 15mm dia complete all as specified and as directed. Make: Jaquar Cat part No-FUS-29281 or equivalent. as approved by GE

S&F in repair cast copper alloy CP shower arm square shape 230mm long with flange complete all as specified and directed by Engr-in-charge. Make : Jaquar or equivalent. as approved by GE. .

S&F in repair brass chromium plated shower rose 150mm square size (without arm) with swivel joints including fixing arm/ pipe all as specified. Make Jaquar Cat part No-OHS-35495 or equivalent. as approved by GE.

S&F in repair brass chromium plated 140mm roud shape hand shower size incl 1.5 mtr long chromium plated flexible tube fixing with wall mixer all as specified. Make Jaquar Cat part No-HSH-1729 or equivalent. as approved by GE.

S&F for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 20mm bore, ISI marked complete all as specified and as directed.

S&F corner glass shelf of size 300mm dia and 8mm thick with chomium plated railing fixed with and incl chromium plated bracket complete all as specified.Make Jaquar Cat part No-CAN-1173 or equivalent. as approved by GE.

S&F cabinet mirror plastic body for toilet of size 350mmx450mm with 4mm thick looking mirror complete all as specified.Make : Prayag/Polytuff.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, incl waste coupling waste coupling of CP brass of suitable size, 32mm dia PVC waste pipe and CP grating and bedding in cement mortar to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 914mm x 460mm, bowl size 405mm x 330mm x 160mm all as specified.

S&F in repair stainless steel plate rack of approved make of size 24''x30"x10" complete all as specified. Make: Prayag Grade-304 or equivalent

M&L for 10 mm thick Gymsum board (mositure resistant) seamless as in the ceiling/ linning fixed with counter sunk screws on and incl GI channels frame work of stardard section as per manufacture,s instructions, fixec @ 1.2 m in one direction and 45 cm in center to center in other direction with necessary fixing arrangmentat their junction point at desired heights below roof slab and incl two coats of plastic emulsion paint over a coat of primer on exposed surfaces. (The frame work shall be fixed with the help of GI suspenders of suitable size with the help of sash fasteners and along wall, making good disturbed surfaces, smoothening the gypsum board, POP lining at joints as required complete all as specified and directed. Make : Gyproc-saint Gobain/Armstong/Diaken.

M&L for POP cornices for seamles false ceiling incl necessary hanging arrangments atc complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap plain with CP grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1,1:2:4 using 20mm graded stone aggregate complete all as specified.

S&F PVC (SWR) soil, waste and vent pipes, 110 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, fixed to wall, with PVC clamps, ISI marked complete all as specified and directed

S&F PVC (SWR) soil, waste and vent pipes, 75 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, laid in trenches or in floors, ISI marked complete all as specified and directed

S&F PVC (SWR) bends, 110mm bore, any radius complete all as specified and directed

S&F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal for 110mm bore PVC pipe complete all as specified and as directed

S&F PVC(SWR) branch piece single (single ‘Y’) equal or unequal for 75mm bore PVC pipe complete all as specified..

S&F for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 110mm bore pipe complete all as specified and as directed

S&F for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 75mm bore pipe complete all as specified and as directed

S&F PVC vent cowl of 110mm dia complete all as specified and directed

S&F stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm dia of bore complete all as directed

S&F rotational moulded polyethylene water storage tank 3 layer white colour water tank, non- toxic effect, algea formation protection (made frome virgin grade of polyethy-lene material which is duly stablized with anti-oxident plastic) of capacity 1000 litres, cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed. Make: Sintex, Polycon, Rotex

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) 75 mm thick in plinth protection, laid in alternate bays not exc. 3.0m in length, finished surfaces even and smooth without using extra cement including demolition existing concrete and rubbish off the premises complete all as specified

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm aggregate) Cement concrete as in sub base including demolition of damaged PCC sub base complete all as specified and as directed

M&L for 25mm thick coloured glossy rubber moulded chequered cement concrete tiles of area exc. 0.08 Sqm and n.exc 0.16sqm each, set, jointed and pointed in net cement slurry mixed with grey cement and pigment in floors including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes including dismantling of existing complete all as specified and as directed.

S&F in repair aluminium die cast body Door closer hydraulically regulated designation No 2, universal type suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60kg ISI Marked complete.

Dismantling of structural steel work of any description including doors, gates, framed trusses etc. complete all as specified and as directed.

Supply and fix mild steel work in tubular trusses, beams, rafters, purlins, main columns, posts etc., for structural work including special shaped washer etc. complete using hollow mild steel sections of square or rectangular tubes conforming to IS: 4923-1997 grade St.-240 fixed with angle cleats or other connecting plates complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness,including nainital or similar pattern roof coverings complete all as specifed and directed

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws with two corrugation side lap complete all as specified and as directed. NOTE: This item of work is to be operated upto 15m Building Height.

-Ditto- all as per item no 91 above here in before but plain sheets on riges,valley gutters and similar works etc complete all as directed NOTE: This item of work is to be operated upto 15m Building Height.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

M&L for preparation of new wood or wood base surfaces and applying malamine polishing on surfaces of any description,width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as directed.

S&F in repair 10 to 12 mm thick AC board as in eaves board and similar work at height exc. 10 m and not exc. 15 m including two coats of synthetic enamel paint a coat of primer complete all as specified and directed.

M&L for Point wiring using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 1.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc fot concealed conduit wiring (In Stone Masonary) with modular flush box metal of GI sheet minimum 1.2 mm thick (ISI Marked) with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour (ISI Marked) of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for One light/Fan point/bell point controlled by one switch 6 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing) Note:- (a) wiring shall be done by using colour coding (b) Earth wire shall be of green colour. (Make:-Finolex/Anchor/Grandlay/Polycab/L &T/Havells)

All as item No 98 above One 3 pin socket outlet, 5 Amp socket outlet on same board with other switches.

All as per item No 98 above but One 3 pin socket outlet, 5 Amp socket outlet on independent board.

One 3 pin 15 Amps socket outlet independent but below the switch board of light points in the same vertical plane, using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 2.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc for concealed conduit wiring (In Stone Masonary) with modular flush box metal of GI sheet minimum 1.2 mm thick (ISI Marked) with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour (ISI Marked) of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for power point controlled with cables, 2.5 sq. mm size (2.5 Sqmm for Phase and neutral and 2.5 Sqmm for earthing) (Make:-Finolex/Anchor/Grandlay/Polycab/L &T/Havells)

Supply and fixing in repairs modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 16 AX Amps One Way switch complete all as specified and directed.(Make:- Cat Part No AHFSXXW161 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree)

Supply and fixing in repairs modular socket outlet fabio series 6 Amps 3 pin unversal socket with child safety shutter, Shrouded terminals compatible with all standard mobile chargers, ISI marked for the same board complete all as specified and directed. (Make:- Cat Part No AHFKPXW063 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree)

Supply and fixing modular charging socket suitable for USB charger 1.5A to charge mobile, polycarbonate material, shrouded terminal, ISI marked 6 Amps One Way complete all as specified and directed.(Make:- Cat Part No 800112 of Indoasian or equivalent Havells/Indoasian/Legrand/Anchor)

Supply and fixing in repairs modular socket (Fabio classic white) outlet 16 Amps shuttered socket (heavy duty) 3 pin unversal socket with child safety shutter, Shrouded terminals compatible 2 ton AC and 3.5KW geyser, ISI marked for the same board complete all as specified and directed. (Make:- Cat Part No AHFKCXW253 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree)

Supply and fixing in repairs modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 6 AX Amps One Way switch complete all as specified and directed.(Make:- Cat Part No AHFSXXW061 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree)

Supply and fixing Sheet Metal enclosure double door for DBs when MCBs to be used SPN-12 Way with 200 Amp rated bus bar complete all as specified and directed. (Make:- Cat Part No 811818 of Indoasian or equivalent Havells/Indoasian/Legrand/Anchor)

Supply and fixing amp rating 240V, 10KA curve 'C' mini miniature circuit breaker (MCB) SPN and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioning (Make: Havells Havells/Legrand/Anchor)

Supply and fixing amp rating 240V, 10KA curve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning (Make:- Cat Part No 811818 of Indoasian or equivalent Havells/Indoasian/Legrand/Anchor)

Supply and fixing in repairs modular Ceiling Ceiling rose, 3 phase/PVC/polycarbonate, isolated body 50 x 65 mm surface type complete all as specified and directed. (Make:- Cat Part No AHLHXCW000 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree)

Supply and fixing in repairs modular 5 stepped type electronic fan regulator- 2M 100W laser marking as reqd at site complete all as per specified and directed. (Make:- Cat Part No AHFRFXW004 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree)

Supply and fixing Aluminium, mild steel silver (satin nickel) finish double spot light great for installation above a dressing mirror, dressing table, to provide illumination while in front of mirror an E14 holder including lamp of 15 W, has a higher light output or a different color temperature with adjustable to required position matching three light code – ML182-3 (Warm White) suitable including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. (Make:-Bajaj/Havells/Indoasian/Legrand/Anchor/Philips)

Supply and fixing FLORETINE WL 1LS B22 SS 09W Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base (Warm White) watt 220 volts suitable for fixing on wall including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. (Make:-Cat Part No LHFOAJE1TZ1I060 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree)

Supply & Fixing only LED lights fitting 20W LED 6000K (4Ft), 220V,AC decorative box type with driver, Aluminium extruded (Intervertor tubelight fittings)holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (Make- Havells/Indoasian/Legrand/Anchor/Philips)

Supply and fixing in repairs LED light fitting 2 feet, 10 watt 220 V AC decorative type with driver holder, Aluminium Extruded(Intervertor tubelight fittings) and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete (Make- Bajaj/Philips/Havells/Indoasian/Legrand/Anchor/PhilipsGE lighting)

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4.0 Sqmm to be drawn through and including PVC conduit 20mm dia medium Grade concealed in walls/roof/floors including taking down the old submain wiring all as directed by Engineer in Charge.Notes:- (i) Two wires of 4 sqmm and one wire of 4.0 sqmm and one run of PVC conduit shall be measured as one unit. (Make- Havells/Polycab/KEI/Finolex)

M&L for Sub Main wiring complete with copper conductor, multi stranded, FRLS, PVC insulated and sheathed, 6 Sq mm, two run 1100 volts grade, incl drawn through PVC suitable size counduit and 6 Sqmm single run for earthing.(Make- Havells/Polycab/KEI/Finolex)

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250mm, BLDC motor (Make: Atomberg/Bajaj/Havells)

Supply and fixing ADELIA WL 1LS E27 ABR Wall mounted, Wall light with Antique brass in colour, 1 x 7.5 W A60 LED filament lamp(Warm White) with 235mmx145mmx165 mm in dimensions, 220 volts IP 20 protection suitable for fixing on wall including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. (Make:-Cat Part No LHFOAFC1TZ1T040 of Havells or equivalent /Indoasian/Legrand/Anchor/crabtree)

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete (Make Havells/Philips/CG/Halonix)

Supply and fixing Bell push, flush type 5 Amps complete all as specified and directed. (Make- Havells or equivalent Indoasian/Legrand/Anchor/crabtree)

Supply and fixing Bell AC 230 Volts, single pole, 50 Hz complete all as specified and directed. (Make:-Havells or equivalent Indoasian/Legrand/Anchor/crabtree)

Supply and fixing Sheet Metal enclosure double door for DBs when MCBs to be used VerticalTPN-4 Way with 200 Amp rated bus bar complete all as specified and directed (Make:-Havells or equivalent Indoasian/Legrand/Anchor/crabtree).

Supply and fixing of geyser Bolt 120mm Long with nut & washers, complete all as specified and directed

Taking down hot water geyser of any capacity after disconnecting, dismantling and removal to trade workshop for repair for servicing of geyser by disconnecting the electric and water supply connections, dismantling the geysers of any size, type & capacity and opening the top and botton cover , thermostat, heating element, safety valve, vent pipe, separating inner & outer tank, removing glass wool insulation complete and keeping aside for re-use after descaling of inner tank by liquid chemical and with pressure water jet and assembling back the geyser including re-installation on wall with studs, nuts & bolts keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed

Supply and fixing ceiling fans complete with blades, down rods,electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fix electric water heater (Geyser), storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Excavation in trenches not exc 1.5 Mtr wide and not exc 1.5 Mtr deep in soft / loose soil and getting out and levelling of bottom surface to required level complete all as specified and directed .

Removing excavated material of soils from site to a distance not exc 50mtr away and depositing where directed not exc 1.5mtr from the starting point complete all as specified and directed .

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed .

M & L for Clear Sand for cushioning under ground cable 8 cm below and 15 cm above in trenches / cable duct filling complete in level complete all as specified and directed.(Punned thickness only measured and paid)

M & L for Brick well burnt locally available sub class 'B' laid over sand cushioning to cable protection in trences keeping width of brick parallel to the length of cable complete all as specified and directed .

Taking down old unsv cable of size 25 & 35 Sqmm 3.5/4 core complete all as specified and directed .

Supply and laying under ground LT Cable XLPE insulated heavy duty armoured sheathed 1100 volts grade of cross sectional area 25 Sq mm, 3.5 core, with aluminium conductor, ISI marked as per IS : 7098 ( Part-1) along with suitable size aluminium cable lugs, gland if required and jointed in any description complete all as specified.Make- Polycab/ Havells/Gloster

S & F in repairs tube light grade galvanized of size 40mm with all fitings laid in trenches/ under road floor alongthe pipe for cable protection of size 40mm bore complete all as specified and directed .

Disconnecting electric supply from electric meters and dismntling MS electric meter box of any type / size including electric meters, switch gear,MCCB/MCBs etc complete and supply fabricate, testing and commissioning of MS Sheet Electric meter box 2 mm thick double door with locking arrangement of size /dimention not less than 130 x75x30 Cm with suitable thickness of hylem sheet for fixing existing electric meter -06 Nos,including provision of new MCCB 100A -01 No., MCB SPN 32 A-07 Nos with suitable size of aluminium busbar for phase & neutral and see through glass-08,connecting internally prewired copper conductor witth electric meter connection of required size ,applied with powder coated synthetic enammeled paint and making good to the disturbed wall surface complete all as specified and directed .

M & L for Earthing complete with galvanised steel earth plate, electrode,600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to GI strip 32x 6 mm thick dia by mens of nuts, bolts, & washers of GI as shown in electrical plate No. 5 of SSR Part-I Connected to earthing ten point all as specified and including necessary earth pit PCC 1:3:6 chanber be 50mm thick PCC 1:2:4 chamber cover with 6mm dia mild steel reinforcement of 10 cm c/c spacing both ways in lieu of CI cover , watering arrangement shall be made with GI pipe light grade of 20mm dia including funnel and protection to earth lead shall be provided with GI pipe light grade 15mm dia unto 7.5 from the earth plate electrode & refilling of soil etc including necessary excavation & earth work in any strata and PCC chamber all as specified and directed by Engr-in-Charge including demolish existing earth pit taking out old materials complete all as specified and directed .

Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

Parhar Enterprise (BID ID -3353372)

ASMEE ENGINEERING SERVICE (BID ID -3345434)

N B ENTERPRISES (BID ID -3344380)

THE SAIRAM CONSTRUCTIONS (BID ID -3345944)

K.S.JITE AND SONS (BID ID -3345627)

M/S Eknath agencies (BID ID -3345940)

SHRINATH CONSTRUCTION (BID ID -3346212)

GS Associates (BID ID -3345668)