SPECIAL REPAIR TO BUILDING NO RA-1 AND M-2 INSIDE FORT WILLIAM UNDER GE (FW) KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar and disposal of debris and rubbish off the premises complete all as directed by the Engr-in-Charge.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish off the premises complete all as directed by the Engr-in-Charge.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutters from the frame) n exc 1.5 Sqm each complete all as specified and directed.

All as per item No. 9 above but exc 1.5 Sqm and not exc 4 sqm each

Dismantling of wrought iron of mild steel work of any descrisption not otherwise privided for, complete all as specified and as directed.

Dismantling boarding of any description fixed in any position with nails complete all as specified and as directed.

Dismantling AC Corrugated, semi corrugated sheets in roof coverings including any type of ridges and disposal of all material, complete all as specified and as directed.

Dismantling timber scantling, 40 sqcm and over in section, in any position, in unframed work, complete all as specified and as directed.

Dismantling of timber fillets, rails, posts, rafters, purlins etc under 40 sqcm in section complete all as specified and directed.

Material and labour for brick work with fly ash bricks , straight or curved on plan exe. 6 meters mean radius built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with fly ash brick straight or curved on plan to any radius in half brick thick wall in cement mortar 1:4 complete all as specified and as directed.

Supply and fixing Mild steel TMT bars 8 mm dia , cut to length and bent to shape as reqd, including cranking , bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

Supply and fixing Mild steel TMT bars 10 mm dia and over cut to length and bent to shape as reqd, including cranking , bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

Material and labour for Reinforced Cement Concrete M-25 (Design Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

Material and labour for Reinforced Cement Concrete M-25 (Design Mix) (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, etc complete all as specified and directed

Use and waste of formwork to side and soffits of floor or roof beams , beam haunching , girders , bressum-mers , lintels , cantilevers , shelves including supports , overhangs etc. also splays between floors and beams etc. ,rough finished flat surface of concrete complete all as specified and directed .

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete complete all as specified and directed.

Material and labour for for 40 mm thick PCC 1:2:4 type B-1 (20 mm graded aggregate ) as in floor and finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

Material and labour for plain cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) as in hold fast block or similar work like bands, plinth courses, lacing courses, parapets, fins fascia, louvers and raiings upto 60cm height, copings, kneelers, bed plates including necessary formwork complete all as specified and as directed.

Supply and fixing 50 mm thick Precast RCC Jali 1:2:4 , type B0 (using 12.5 mm graded aggregate ) and set in cement mortar 1:4 including dismantling old RCC Jali complete all as specified and directed

Material and labour for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

Material and labour for cutting holes in brick walls exc. one brick but n exc. two brick built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed .

Material and labour for for cutting Grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed .

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Material and labour for 15 mm thick rendering in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note:- WPC shall be mesured and paid separately)

Material and labour for 15mm thick rendering in cement mortar (1:6) on fair faces of brickworks finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for for rendering 5mm thick cement plaster in cement mortar (1:3) on fair ceiling faces of concrete finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparing newly plastered surfaces of internal walls, etc and applying two coats of acrylic washable distemper over a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed.

Material and labour for applying three coats of white washing including preparation of new plaster surface of walls etc complete all as specified and directed.

Material and labour for applying two coats of white wash on ceiling including preparation of new plastered surfaces complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for complete removal of existing treatment from old wall surface and applying two coats of acrylic washable distemper over a coat of alkali resistant primer applied over a coat of water proof wall care putty(Berger-Home shield or equivalent) complete all as directed.

Material and labour for preparation of old plastered or un plastered surfaces of wall and cornices by brooming down with steel wire brushing , scraping down smoke spot moulds , mass and efflorcscent salts and trating oil and greay spots and applying one coat of white wash to wall complete all as specified and directed

Material and labour for for applying one coat of acrylic washable distemper to old decorated plastered (distempered) surfaces of ceiling including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed by Engineer -in-Charge.

Material and labour for preparing new plastered surfaces of walls by washing, rubbing down stopping of painted surfaces and applying two coats of water based acrylic weather proof exterior emulsion paint over a coat of primer, complete all as specified and as directed.

Material and labour for preparing old exterior emulsion painted surfaces of walls by washing, rubbing down stopping of painted surfaces and applying water based acrylic weather proof exterior emulsion paint , complete all as specified and as directed.

Material and labour for preparing old decorated plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed

Material and labour for applying one coat of synthetic enamel paint to old painted steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer -in-Charge.

Material and labour for preparing old painted wood and wood based surfaces of any description not otherwise described, over 100 mm width or girth and applying one coat of synthetic enamel paint complete all as speciried and as directed.

Material and labour for preparation of new wood or wood base surface of any description over 10cm width or girth and applying two coats of synthetic enamelled paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for MS steel work in tubular/square/rectangular trusses, tubular posts and rafter/purline including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240, compelte all as specified and as directed.

Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure steam Crude Everest Non Asbestos Fibre Cement plain Board (E-Board Classic) in a grid of GI system duly suspended with 4mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall, Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid and painted with two coats of acrylic emulsion paint of approved shed /make over a coat of cement primer before installing it on the grid all as specified and directed..

Supply and Fixing PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed by the Engineer-in-Charge.

Material and labour for 5 mm thick PVC sheet fillet of width 50 mm at interval of 250 mm c/c fixed with 65 mm nicked cadmium scres @ 200 mm c/c for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and directed.

Supply and fixing in repair coloured( any) PVC seat cover for EWC of any description with hinging device complete all as specified and directed by Engr-in-Charge.

Materal and labour for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, as in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

All as per item No 53 here-in-before but on vertical surfaces such as in skarting ,set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of the tiles over and incl. 10mm rendering in CM (1:3) complete all as specified and directed.

Material and labour for ceramic non skid coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc., laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile surface all as specified and directed.

All as per item No. 55 above here in before but on vertical surfaces such as skirtings, dados, risers etc over 10mm thick rendering in CM 1:3 complete all as specified and directed.

Supply and fixing glazed ceramic colour tiles (450x350 x 7mm thick ) on dado & skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick cement plaster with rough finished in cement mortar 1:3 to received tile complete all as specified and directed.

Material and labour for granite stone slab (of any type) 18 to 20 mm thick, machine cut ,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortor 1:4 & cutting, polishing and making moulds on edges as in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick over 15mm thick screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed by the Engr-in-Charge.

Material and labour for machine cut kota stone slab in verical surfaces as skiring, riser etc. 20-25 mm thick over 10mm thick rendering in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed by the Engr-in-Charge.

Material and labour for 25 mm thick pre-polished cement concrete chequred tiles ,coloured, glossy finish , smooth in design , joint free, compressive strength 300 kg/Sqcm, ISI marking (IS-13801-1993), set, jointed in neat cement slurry and pointed with white cement mixed with pigment to match over and including 20mm thick scread bed in cement mortar 1:6 complete all as specified and directed.

Taking out complete existing roof treatment from roof surface & roughening of old concrete floor/ wall surfaces including cleaning the roof surfaces by brushing sweeping etc and removing rubbish material complete all as specified and as directed.

Material and labour for water proofing treatment on existing cleaned RCC roof with the following specification and manufacturings instruction complete all as specified and as directed:- (a) Preparing and clening of fully dry surfaces as per IS3067-1966 (b) Applying bitumen primer conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm (c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.0Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application. The over laps shall be minimum 100mm on the transverse direction and 75 mm on longitudinal direction. (d) Applying one coat of aluminium paint @0.10 ltr per sqm over APP based polymeric membrane.

Supply only integral water proofing compound all as specified and as directed.

Supply and fixing 38 mm thick glass dividing strips 3 mm thick complete all as specified and directed .

Supply and fixing 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

All as per item No 66 here-in-before but in exc 0.5 sq.m in each pane

Supply and fixing 4.8 mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing 5.5mm thick plain ordinary sheet glass for Al door/ window complete all as specified and as directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm complete all as directed and specified .

All as per item no 70 here in before but Supply and fixing in repair .

Supply and fixing anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fixing Anodised aluminium door, window and ventilator shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Supply and fixing solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. Quantity Breakdown - M2-1.40

Supply and fixing 30 mm thick, Flush shutters, factory made ,solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing in repair prelaminated particle board 12mm thick , interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work complete all as specified and directed.

Supply & fixing 35 mm thick, 2nd class hardwood, factory made, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing 30 mm thick, factory made, Second class hardwood, glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, etc complete all as specified and directed in SSR Part I Section 8 clause 8.24 (b).

Supply and fixing well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

Supply and fixing MS Framed work such as guard bar , grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Supply and fixing mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties,flat iron fillets for securing wire mesh, wind tie and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

Treating small articles such as hold fast etc area tarred n exc 0.10 Sqm each incl preparation of surface complete all as specified and directed.

Preparing surfaces of wood and wood based materials, steel and iron works, new or old of any description and girth treating ends of posts, back of chowkats etc, area tarred exc 0.1 Sqm but n.exc 0.5 Sqm each with tar or coal tar black paint complete all as specified and as directed.

Supply & Fixing second class hard wood small fittings such as brackets of any type , stopper/cleat for door or window, articles next. 200 cum each with MS butt hinges cold rolled medium weight 50 mm long complete all as specified and directed.

Supply and fixing 2nd class hard wood in boarding 20 mm thick planed both side with butt joints & fixed with nails in any situation complete all as specified and directed.

Supply and fixing second class hardwood, scantlings, clean sawn, in framed work complete all as specified and directed.

All as per item no-87 here in before but wrought , in unframed work complete all as specified and directed.

Material and labour for second class hard wood, Plain fillets. square, rectangular or triangular in section, wrought, secured with nails or brads, cross sectional area exc 6 Sqcm and n.exc 13 Sqcm complete all as specified and directed.

All as per item no-89 here in before but area exc 13 sqcm and n.exc 25 sqcm complete all as specified and directed.

Supply and fixing in repair 18/19mm thick block board Grade-I interior quality commercial type fixed as in cabinet and all as directed by Engr-in-Charge.

Supply and fixing in repair 0.9mm thick decorative laminate type -I of surfaces finish ,colour and pattern as approved fixed with approved adhesive as per manufacturer instruction complete all as specified and directed.

Supply and fixing in repair brass locks for cup board Grade-I of size 50mm, 4mm levers complete all as directed by the Engineer-in-Charge.

Supply and fixing in repair 12 mm thick commercial faced plywood grade BWR type B-B fixed with screws to timber frame work as in cabinet, pelmet boxes, cup board etc all as directed by the Engr-in-Charge .

Supply and fixing rolled mild steel in joist, channel, angle or Tee section fixed independently etc up to height 4 to 6 mtr from each floor level (cut to ordinary length ie. Within 20mm of the length indicate) Gde Fe-410-W-(Gde-E-250) Quality-B including using former iron props and steel plates to existing RCC over head members like beams, slabs etc so as to ensure safety of existing structure and floor during repairing works complete all as directed by Engr-in-Charge. Note: The section to be provided under this item will be used as beam to support floor/roof.

Supply and fixing 4mm thick asbestos cement plain building board fixed to timber frame work with screws in ceiling, complete all as specified and as directed.

Cutting chases for water tubing, pinning in making good to facing where required in CM(1;3) to brick wall cutting grith n.exc. 10cm girth complete all as directed.

Supply and fixing 1000 ltrs capacity rotational moulded polyethylene water storage tanks (Cylindrical verticle with closed top),multi layer, hoisted and fixed in position including 20 mm dia float valve and tank cover including taking down old unserviceable one complete all as specified and directed .

Supply & fixing aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm complete all as specified and directed.

All as per item no 99 here-in-before but supply and fixing in repairs complete.

Supply and fixing in repair aluminium (extruded section body) hydraulically door closer universal type designation No 2 universal type, suitable for door shutters up to 701mm to 850 mm in width and of weight not more than 36 kg to 60 Kg as directed by the Engr-in-Charge.

All as per item No 101 here-in-before but upto 851 to 1000 mmm in width and weight between 61 to 80 kg

Supply and fixing medium weight cold rolled mild steel butt hinges 100 mm long complete all as specified and directed.

All as per item No 103 here-in-before but 75 mm long

Supply and fixing Aluminium anodised tower bolt 200 mm long of extruded section

All as per item No 105 here-in-before but 150 mm long

All as per item No 105 here-in-before but 100 mm long

Supply and fixing 450 mm long brass steel skeleton tower bolts with cast brass plate and staples and rolled or dwawn brass bolt.

Supply and fixing 150 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

All as per item No 109 here-in-before but 125 mm long

All as per item No 109 here-in-before but 100 mm long

Taking up or down 15mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.

All as per item No 112 here-in-before but 20 mm bore

All as per item No 112 here-in-before but 25 mm bore

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

All as per item No 115 here-in-before but 20 mm bore

All as per item No 115 here-in-before but 25 mm bore

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compelte all as specified and as directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compelte all as specified and as directed.

Supply and fixing 0.56 mm thick plain aluminium sheeting alloy 31000 H4 as in ridges, hips, valley gutter, drip and straight flashing etc complete all as specified and directed.

Supply and fixing in repair 25mm dia brass chromium plated curtain rod with fixing brackets, stops, rollers etc complete all as specified and directed .

Supply and fixing in repair fancy type metal finish curtain bracket fixed to walls complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repairs coat hooks, 175mm (six points) to 250mm solid aluminium body complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair cast type ,polished bright brass handles 100mm long complete all as directed by the Engineer-in-Charge.

Supply and fixing in repair continuous (piano) hinges mild steel bright finish width of flap 30mm when opened complete all as directed by the Engineer-in-Charge.

Supply and fixing in repair 4 levers brass body, lock ,drawer graded 1 size 50 mm, complete all as directed by the Engineer-in-Charge.

Supply and fixing in repair aluminium 'E' channel for sliding drawer shutter of cub board in two way 200 mm long complete all as directed by the Engineer-in-Charge.

Supply and fixing in repair 40 mm dia, cup board knobs fixed with nut, screw and washer of brass polished.

Supply and fixing in repair of stainless steel sink with one side draining board made out of 1.00mm thick sheet for kitchen with plug washers, waste pipe, CI cantilever brackets, connection union overall size 915mm x 460mm with blow i.e. 410 x 355x 165mm incl making good damaged surfaces with cement mortar (1:3) to match with the existing and complete all as directed by Engineer-in-Charge.

Supply and fixing in repairs stainless steel round grating 150mm dia complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair 25 mm Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe mini weight 142 grams complete all as specified and directed.

Supply and fixing in repair 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair 15 mm bore bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down , screwed for iron pipe of 15 mm bore and fixed , complete all as specified and directed

Supply and fixing as in repair 15 mm bore stop valves cast copper alloy,fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed.

Supply and fixing in repair chromium plated two-in-one bib cock with wall flange, fixed with 150mm bore iron pipe as directed by the Engr-in-Charge. Make : ESS-ESS, Cat No. TM-103 or equivalent product of Make :- Jaquar ,Parryware,Marc .

Supply and fixing in repair 15 mm bore, health faucet ABS body with wall hook and 1.2 m long CP tube stainless steel flexible hose with all accessories complete all as specified and directed.

Supply and fixing in repair chromium plated brass angular stop cock with wall flange fixed to 15 mm bore of iron pipe complete all as specified and as directed. Make : Jaquar Cat No. TM-104 (Chrome) or equivalent product of Make :- Jaquar ,Parryware ,Marc.

Supply and fixing in repair fancy type chromium plated wall mixer with telephonic shower arrangement only with crutch fixed with 15 mm bore iron pipe complete all as directed by Engr-in-Charge. Note : Telephonic shower will be measured and paid separately. Make : ESS-ESS, TM-112 (Chrome) or equivalent product of Make :- Jaquar , Parryware ,Marc.

Supply and fixing hand shower 100 mm dia round shape multi flow with air effect (ABS body and face plate chrome plated) with rubbit cleaning system including chromium plated flexible shower tube of suitable dia and 1.5 m long complete all as specified and directed. Make : Jaquar cat no HSH -1717 for hand shower and cat no SHA 549D8/ 549D12 for shower tube

Supply and fixing 15mm dia fancy type chromium plated basin mixer foam flow screwed for iron pipe incl taking down old one complete all as specified and directed by Engr-in-Charge. Make : ESS-ESS, Cat No. TM-108(Chrome) or equivalent product of Make :- Jaquar ,Parryware ,Marc.

Supply and fixing in repair chromium plated towel ring complete all as specified and directed by the Engr-in-Charge. Make : ESS-ESS, Cat No. AC 502 or equivalent product of Make :- Jaquar , ,Parryware ,Marc.

Supply and fixing and in repair chromium plated toilet paper holder complete all as specified and directed by the Engr-in-Charge. Make : ESS-ESS, Cato No.AC206 or equivalent product of Make :- Jaquar , Parryware, Marc

Supply and fixing in repair chromium plated Over head shower with arm fixed to 15 mm bore Iron pipe complete all as directed by Engr-in-Charge. Make : ESS - ESS, Cat No OH 104 A or equivalent product of Make :- Jaquar , Parryware ,Marc.

Supply and fixing cascade type (coloured) floor mounted water closet with low level flushing cistern coloured with floor trap, PVC coloured seat cover and connecting pipe etc including taking down old one complete all as directed by Engineer-in-Charge .Make : Parryware Code No. C-0232, C-0711 C-2054, E-8300 & E-8016 or equivalent product of Make :- Hindware,Jaquar.

Supply and fixing in repair 6mm thick bevelled edge mirror of size as required fixed on 6mm thick acrylic PVC sheet complete all as directed by the Engr-in-Charge .

Supply and fixing in repair chromium plated toilet tumbler holder (including with tumbler and chromium plated wall flange), fixing with stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Make: Jaquar cat No. CAN 1141N or its equivalent in make ESS-ESS/ Parryware

Supply and fixing Stainless steel kitchen rack of size 31" x 24" x 10" fixed in wall with screws and washer incuding taking down old one complete all as specified and directed.

Supply and fixing in reapir Chromium Plated front glass shelf of size 460mm x130mm fixed to wall with Chromium Plated screws complete all as specified and as directed.

Supply and fixing in repair various china white pedestal pattern wash hand basin of size 560mm x 430mm incl providing 32mm dia CP wasted coupling,CP bottle trap bracket, 32mm dia PVC waste pipe and making all necessary connections, fixed as directed by Engr-in-Charge Make : Parryware model No C-0377,C231C,C230A Popular range or equivalent model of make Hindware ,Cera , Jhonson Pedder

Supply and fixing in repairs vitreous china (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts(except flushing cistern and flush pipe) incl plastic water closet seat cover (coloured) and mild steel chromium plated or aluminium hinging device complete all as specified and directed by Engr-in-Charge. Make : Parry ware model No C-0278/ 0297 or equivalent model of make Hindware ,Cera , Jhonson Pedder.

Supply and fixing in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing in repair 600mm long brass chromium plated 20mm dia 'D' type towel rail complete all as specified and as directed.

Supply and fixing in repair10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

Supply and fixing Vitrious china squatting Pan , Orissa ' pattern , size 580x440 mm white , with intregal foot rests (excluding flushing cistern and flush pipe ) including connection to the trap, and to flushing pipe , anti- syphonage pipe etc , making good to floor including taking down the old one complete all as specified and directed. Make : Parry ware model No C-0117 or equivalent model of make Hindware ,Cera , Jhonson Pedder.

Supply and fixing in repair vitreous china Urinal, half stall type, white including connections to flush pipe and outgoing pipes complete all as specified and as directed. Make : Parry ware model No C-0575 or equivalent model of make Hindware ,Cera , Jhonson Pedder.

Supply and fixing in repair waste coupling of 32mm bore of discharge pipe, PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and as directed.

Supply and fixing in repair waste fitting of 32mm bore of discharge pipe, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

Supply and fixing 32mm bore of discharge pipe, Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches including taking down old one complete all as specified and as directed.

Supply and fixing 100 mm bore cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls including taking out old pipe complete all as specified and as directed by the Engineer-in-Charge.

All as per item no160 here in above but laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge. Note : Earthwork shall be measured and paid separately under respective item.

Supply and fixing in repair 100mm bore cast iron (sand cast) sockets (Double Coller) complete all as specified and as directed.

Supply and fixing 100 mm bore cast iron (sand cast) branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 100 mm bore cast iron (sand cast) bends (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 100mm dia CI vent cowl complete all as specified and as directed.

Supply and fixing in repair 75mm dia CI floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (using 20 mm gr stone agg ) complete all as specified and as directed.

Supply and fixing in repair 100x150 mms salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' complete all as specified and as directed.

Supply and fixing Mono block water pressure pump set of capacity 0.50 HP single phase , discharge range 36-60 Lpm , working in voltage range 220-240 V with operating pressure range 1.4 -2.4 (Bar) complete including with closed discharge valve and connected fittings and depositing the old pump to MES store yard complete all as specified and directed . Make: KILOSKAR - ETERNA, Model SJPBS 42420- HL or equivalent model of make Crompton Greaves ,KSB

Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power ) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

Material and labour for concealed point wiring with FR PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FR PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC conduit terminated in modular switch boards for fixing of switches, sockets, fan regulators etc for the following [Note: - Modular switch boards shall be measured and paid separately]: - (a) One light point or one fan point or bell point controlled by one switch

(b) One 3 pin socket outlet, 5 Amp independent

(c)One 3 pin socket outlet, 5 Amp on the same board with other switches

All as per item No. 170 above but wiring with FR PVC insulated unsheathed multistranded copper conductor cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 5/15 Amps switch socket combination on Independent board complete all as specified and directed. [Note: - Modular switch boards shall be measured and paid separately]

Material and labour for concealed point wiring with FR grade PVC insulated unsheathed multistranded copper conductor cables of 4sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 2.5 sqmm size through and including PVC conduit terminated in modular switch boards for fixing of switches/ sockets for one 3 pin socket outlet, 15 Amps and two 3 pin socket outlet 5A on independent board complete all as specified and directed. [Note: - Modular switch boards shall be measured and paid separately]

Supply and fixing modular switch 1 way 6A, 1 Module 250 volts complete all as specified and as directed.

Supply and fixing Modular switch 1 way 16A, 1 Module 250 volts complete all as specified and as directed.

Supply and fixing modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing modular Bell push 6A, 1 module complete all as specified and directed.

Supply and fixing Bell ding dong, A.C 230 volts, single pole

Supply and fixing modular Fan step regulator, 120W - 2 module complete all as specified and directed

Supply and fixing modular Blank plate, 1 module

Supply and fixing modular White cover plate with frame, 1 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 2 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 3 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 4 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 6 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 8 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 12 module complete all as specified and directed

Supply and fixing modular Metal flush box 1/2 module complete all as specified and directed

Supply and fixing modular Metal flush box 3 module complete all as specified and directed

Supply and fixing modular Metal flush box 4 module complete all as specified and directed

Supply and fixing modular Metal flush box 6 module complete all as specified and directed

Supply and fixing modular Metal flush box 8 module complete all as specified and directed

Supply and fixing modular Metal flush box 12 module complete all as specified and directed

Supply and fixing sheet metal enclosure for MCB DB double door single pole & Neutral 8 way with common bus bar. complete all as specified and directed.

Supply and fixing MCB 'C' series single pole (SP) 6 to 32 Amps, breaking capacity 10KA. ,240 volt complete all as specified and directed.

Supply and fixing MCB 'C' curve single pole neutral (SPN), 32 Amps with breaking capacity 10kA,,240 volt complete all as specified and directed.

Supply and fixing in repair AC short circuit protection motor starter 25 Amps capacity AC 230 Volt complete all as specified and directed.

Supply and fixing ceiling fan ,5 star rating ,1400 mm sweep complete AC single phase 230 Volt 50 HZ connecting with flexible cable 3 core copper conductor of size 23/0.0076 of suitable length from ceiling rose to ceiling fan including all hanging arrangement complete all as specified and as directed.

Supply & fixing heavy duty Exhaust fan 230V single phase, metalic body, 1400 rpm, 300 mm sweep including louvers and making suitable hole and all accessories for fixing Exhaust fan all asspecified and directed by Engr-in-Charge.

Supply and fixingWall mounted air circulator fans with double pull cord for swivelling and speed regulation of size 400 mm sweep with all accessories complete all as specified and directed.

Supply and fixing LED Ceiling light fitting 40 W recess type flat panel 2`x2` fabricated CRCA sheet housing duly powder coated with high efficient LED`s & glare free full opal diffuser, IP 20 complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specifide and directed. Make :- HPL 2x2 clean room 40 w or equivalent model of make as specified in PS cl no 48 ,Sl no-47

Supply and fixing LED Ceiling light fitting 36 W minimum colour temperature 4000K, Luminair efficiency >100lm/w with suitable driver complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specifide and directed. Make :- Bajaj cat no BZRSQL 36 W GZ1 CW or equivalent model of make as specified in PS cl no 48 ,Sl no-47

Supply and fixing LED tube light fitting 20 watt , mounted on wall / ceiling connected with insulated unsheathed flexible copper wire of suitable size (length not exceeding 0.5 m) from ceiling rose complete all as specified and directed. Make :- HPL Neptune Plus 20 W CW or equivalent model of make as specified in PS cl no 48 ,Sl no-47

Supply and fixing LED wall lamp opal glass with chrome finish mounted light fitting E-14, 4 watt, mounted on wall connected with insulated unsheathed flexible copper wire of suitable size (length not exceeding 0.5 m) from ceiling rose complete all as specified and directed by Engr-In-Charge. Make :- Jaquar KCH-CHR-MB 160275211A or equivalent model of make as specified in PS cl no 48 ,Sl no-47

Supply and fixing adjestable bed side LED lamp with clear lens with color temperature 3000 K suitable for 3 W metal and synthetic material lumen 150lm complete all as specified and directed. Make :-Philips Model no 48042/30/31 or equivalent model of make as specified in PS cl no 48 ,Sl no-47

Material and labour for Sub main wiring with two runs of 6 sqmm (Nominal area) single core cable FR PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through PVC conduits/casing-caping of suitable size, fixed to wall/ceiling etc including one run of 6 sqmm (nominal area) single core, FRLS PVC insulated, multistranded, unsheathed, copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size including taking down old sub main wiring complete all as specified and as directed by Engineer-in-charge. Note : PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length.

All as per item no -208 here in before but sub main wiring with 2 run of FR PVC insulated and unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FR PVC insulated & unsheathed copper conductor of nominal cross sectional area 4 sqmm as earth continuity conductor drawn through & including PVC conduit of suitable size complete all as specified and directed. Note : PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length.

All as per item no -208 here in before but sub main wiring with 4 run of FR PVC insulated and unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith two run of FR PVC insulated & unsheathed copper conductor of nominal cross sectional area 4 sqmm as earth continuity conductor drawn through & including PVC conduit of suitable size complete all as specified and directed. Note : PVC Conduits/Casing-caping, four run cables and two run of earth wire will be measured as one length.

All as per item no -208 here in before but sub main wiring with 4 run of FR PVC insulated and unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm alongwith two run of FR PVC insulated & unsheathed copper conductor of nominal cross sectional area 10.0 sqmm as earth continuity conductor drawn through & including PVC conduit of suitable size complete all as specified and directed. Note : PVC Conduits/Casing-caping, four run cables and two run of earth wire will be measured as one length.

All as per item no -208 here in before but sub main wiring with 4 run of FR PVC insulated and unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith two run of FR PVC insulated & unsheathed copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through & including PVC conduit of suitable size complete all as specified and directed. Note : PVC Conduits/Casing-caping, four run cables and two run of earth wire will be measured as one length.

Taking down the light fitting any type from existing wall/ceiling and re fixing it in same or other position complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 5 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion including dismantling old one.

Material and labour for GI earth continuity conductor of 4 mm dia including taking out old one complete all as specified and directed.

Supply and fixing five star rated Storage water heater 25 ltrs cap 2 KW AC 230 Volts vertical mounting,white colour including connecting cord and 15 Amp 3 pin plug, safety valve, nuts and bolts, complete including grouting of nuts and bolts in wall and making good the disturbed surface also depositing the old one to MES store yard complete all as specified as directed. Make : Havells Senzo GHWASESWH025 Ltrs or equivalant model of make Bajaj,Venus

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

S. K. CONSTRUCTION SYNDICATE AND ENGINEERING CO.

UNIVERSAL

S.M.CONSTRUCTIONS

M/S S. K. SARKAR

ARJUN DAS VALECHA

JAGATMATA ENTERPRISE