PROVN OF CERTAIN BR AND EM WORKS IN THE CLASSROOMS AND CBT LAB IN AIRHANGER OF AIRFORCE FACULTY CERTAIN ADDNALTN IN ROOM NO.202 227 255OFARMYFACULTY ADDN ALTN BR AND EM TO MI ROOM BLDG TO PROVDIE SPACE FOR MED STORES AND MINOR WKS IN DIGHI

Amount

PART - I (BUILDING BY ADDN/ALTN B/R PORTION) Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar 1:6, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as spd and directed

M&L for granite(of any type) work(table rubbed and polished) cooking platform and like set in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to matach with shade of granite thickness of granite 18 to 20mm

S&F, Non skid ceramic tiles Coloured 7 to 8 mm (square/rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floors etc set and jointed in neat cement slurry & pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 .

M&L for coloured glazed ceramic tiles 350x250x7mm / 450 x 350 x 7mm thick in dado/ skirting ,set and jointed in neat cement slurry & pointed in coloured cement.

M&L for Rendring 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 on walls ,finishing surfaces even and smooth w/o using extra cement. Note : 1. mixed with water proofing compound @ 3% by weight of cement complete all as specified. 2. Water Proofing compound shall be measured and paid for seprately as "Supply Only"

M&L rendering 5 mm thick in CM (1:3) on concrete surface in ceilling finished even & smooth w/o using extra cement.

M&L for rendering 15mm thick on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement complete all as specified.

complete removal of existing surfaces on walls ,ceiling , fins , fascias etc , and applying two coats of weather proof exterior paint (Apex Ultima )or approved equivalent make,white or tinted ,over a coat of primer including necessary scaffolding all as specified and directed.

M&L for preparing of new surfaces wall applying two coats of OBD, white or tinted, over 3mm thick wall care putty and including primer all as directed .

M&L for complete removal of new plastered or unplastered ceiling surfaces and applying three coat of white wash as specified and directed by Engr -in-Charge.

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (40mm graded stone aggregate) finished even and smooth, without using extra cement as in plinth protection and path etc complete all as specified and directed.

Taking down chowkats or frame with shuters (without taking off shutters from the frames) not exc 1.5 Sqm each.

M&L forming jambs, Cills etc. in cement mortat 1:6, to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete all as specified and directed.

S&F three track sliding window with 4mm thick tinted glass in two shutter and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing including good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge. Series of aluminium section as per Jindal is (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352.

S&F anodized aluminium powder coated of any colour (thickness of powder coating not less than 50 micron), in frame for doors, with one or more rebates including joining cleat for fixing etc ,complete all as specified. (Jindal Section No 20048=0.942 Kg/M)

S&F anodized aluminium powder coated door shutters, aluminium section weighing not less than 0.55 Kg/M including necessary joining cleats, glazing clips, rubber neoprene pakcing, Handles 2Nos in each shutter, hinges, anodised aluminium snap beading screw etc complete all as specified.

M&L Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed

M&L for Locks, drawer,grade I, size 75 mm 4 Lever in brass fixed to Aluminium door with duplicate keys

M&L for aluminium anodised barrel tower bolt of extruded section and fixed 200mm Long

S&F 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to Aluminium frame work with 6mm thick teak wood beading/edging alound.

S & F MS framed work such as grills gratings etc. with ends of bars shouldeed and / or riveted, or forged into spikes; framed guard bars and similar works conforming to Fe 290 Gde - E- 165 including welding etc complete all as spd

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified.

Material and labour for Precast cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in cover slabs of manholes, gully traps etc set in cement mortar (1:4) complete and including formwork all as specified and directed.

Material and labour for mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified.

S&F of mineral fibre acoustic suspended ceiling system with prima fine fissured (K2C2) tile with semi concealed grid , the tile should have humidity resistance (RH) of 99% , NRC upto 0.6, light reflectance> 83%, thermal conductivity K= 0.052 to 0.057 w/m, colour white fire performance class O/class 1 (BS476 part6 &7) in module sizeof 600x 600x16 mm with Bio block coating on the face of the tile, impact resistant and suitable for green bldg application, eith recycled contentof 63 %. The tile shall be laid on semi concealed grid system with 15 mm white flange incorporating 6 mm central reveal in white/black colour and with web height of 38 mm and load carring capacity of minimum 11.68 kg/sqm.Silhouette. main runner and cross tees to have mitred ends & birdmouth notches to provide mitred cruciform junction. The T sections have galvanising of 120 gms/sqm and passed through 500 hrs of salt test. the tile and grid system used together should carry a 15 year warrantee ( Make : armstrong, saint Gobain)

M&L for acoustic wall paneling comprising of GI steel section framework of 600 X 600mm center to center using vertical section of 48mm X 34mmX 0.55mm and horizontal section of 50mmX32mmX0.55mm fixed to wall using necessary fittings. Glasswool of 50mm having density 48 kg/cum is then inserted in the slots. Finally light weight calcium silicate incombustible panels of size 595 mmX 595 mmX 12 mm fixed on grid work with screws, all as specified and directed by Engineer-in Charge

S&F Venition blends with design on inner/outer face roll down type made out of fibre cloth fixed, to wall with necessary Aluminium brackets, screws etc including Alluminium frame for venilion blinds etc all as approved by GE all as specified and directed. Make : Vista and Levador or Equivalent

Surface dressing not exc 15 cm deep and getting out in soft/ loose soil complete all as specified.

M & L 75 mm thick PCC (1:4:8) type D2, using 40 mm graded stone aggregate as in sub base surfice finished even and fough to receive floor topping complete all as specified.

M&L PCC in kerb Stone precast (factory made) any shape and size or as directed by engr in charge including weathering, slightly rounded or chamfered angles and throating, in type B-1 1:2:4 (20mm graded agg) set in cement mortar 1:4, complete all as spfd and directed.

M & L for machine made Rubber moulded precast conctete interlocking paver block (coloured), Glossy finish pre polished of any shape and size with white cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as spfd and directed.

M&L for spreading and levelling 25 mm thick sand cushioning

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete.

M&L Mirror polished kota stone 20-25mm thick in riser of steps, skirting, dado and piller laid over backing coat of 12mm thick in CM 1:4 and jointed with as per above item 100mm High

PART - I (E/M PORTION) Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down sub main wiring complete including fitting and fixtures and removing materials. making good the disturbed surfaces of walls, floors, roof etc, all as specified and as dirfected

Taking down DBs / Metra plug and socket any size and ant capacity all as specified and as dirfected.

M&L for Point wiring complete with multistranded copper conductor cable (ISI marked) 1.5 Sqm PVC insulated, unsheathed cable 1100 volts FRLS grade drawn through in and including concealed non metallic rigid PVC conduit and all accessories such as bends, tees, junction boxes etc, concealed conduit in walls / roofs / ceiling etc.and including provision of continuous earth wire of size 1.5 Sqmm copper conductor PVC insulated unsheathed connected to earth dolly, Including terminated in terminal box made out of 1.60 mm thick MS sheet concealed in walls and including Metal flush box with Modular white cover plate and top as per site requirement for housing the switches, socket outlet, fan regulator etc, cutting chases and making good to disturbed surface complete for the following :- (a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One 3 pin switch socket outlet point 5 Amps on independent board.

(d) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size.

S & F modular switch1 way 6A, 1 module

S & F modular switch1 way 16A, 1 module

S & F Modular socket 6A 2/3 on combined 2 module

S & F Modular socket 6A/16A-2/3 pin combined 2 module

S & F fan regulator electronic 2 modular type volts AC 50 HZ ,100 Watts,4 step complete all as directed.

S & F LED 36 watt reccessed mounting 2 x 2 luminaire white powder coated CRCA housing with high powder LEDs .Aluminium front frame with flat white high transmission acrylic cover with complete accessories all as specified and directed by engr-in charge. MAKE- BAJAJ CAT NO BZRSQL 36W GZi NW / wipro cat part - CRCO10R038HP57GL1 or other.

S & F LED CYLINDRO light 25 watts offers various luminous intensity levels from 1500-3500 lumens which is the perfect alternate to conventional HID Lamps and suitable for 3 circuit 4 wire with universal track 2mtr 3 phase as per site requirement With all accessories to the fixed ceiling/roof/wall etc all as specified and directed by Engr-in-charge. MAKE-HAVELLS, Item Description:- NCYLINDROTSS25W857S38DBLK, HSN Code 9405.

S & F LAN socket connector RJ 45 with socket with copper feed modular type all as directed by Eng-in-Charge.

S & F LAN cable 4 pairs PVC insulated and PVC sheathed in Pvc Concealed conduit all as per directed by Engr-in-charge.

Taking down the defective ceiling fan of any sweep and make after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the ceiling fan by thoroughly cleaning the bearing, shaft, stator, rotor & applying the lubricant / grease to the bearing including applying one coat of painting re-fixing and testing and ceiling fan rode to the extended of length in all respect for smooth running complete.

M & L for submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded and including suitable size of PVC conduit and all accessories concealed in walls / roofs / ceiling etc. earth dolly, terminated in terminal box including cutting chases and making good to disturbed surface complete all accessories all as specified and directed by Engr-in -charge for the following. Note : (i) Two runs of copper conductor and one run of earth copper conductor shall be measured as one length. (a) 2 x 4 sq mm and 1 x 4 sq mm as earth wire

S & F Single pole and neutral enclouser with two pin and earthplug and socket complete with one single pole MCB with 240 V, 20 Amps.

M & L for dismentling, installation and relocated of existing split type AC 1.5TR/2TR capacity in the location as directed including provision of 45 x 45 x 5 mm angle iron frame work for mounting of out door unit and indoor unit with the following :- (i) Fixing of refrigerant piping made out of copper of 3/8" for discharge line and 5/8" for suction line duly insulated for required length and gas charging as per Requrenment. (ii) PVC pipe for the drain water removal from the room as per site requirenment.

PART -II (B/R PORTION) Demolition of brick work built in cement motor incl quoins, arches, pillers etc complete all as specifed and directed by Engr-in-charge

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as spd and directed

Taking down chowkats or frame exc 1.5 Sqm but nexecutive each with shutters of door & windows.

Taking down chowkats or frame exc 1.5 Sqm each (above worked)

M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L for 10mm thick vitrified ceramic tiles (square/rectangular) polished area of each tile not exceding 0.36 sqm in flooring over 15mm thick screed bed in cm 1:6, set and jointed in neat cement slurry and pointed in white or colered cement to match complete all as specified.

All as per sl item 205.00 above but on vertical surface of wall skirting over 15mm thick rendering in cm 1:4.

M&L for 15mm thick plastering on brick masonry/concrete surface in finished even & smooth without using extra cement in cm 1:6.

S&L 165x60mm size pressed steel frames for door with one or more rebutes incl necessary fixing luges lock, strike plate etc.

S&L 35mm thick flush shutters soild core construction, with block board care & plywood face panels, commerical type ISI marked all sides with 6mm thick teak wood edging, and also provide on frame face decorative venear face lipping.

S&F aluminium section 3 brack sliding windows of standard alu section (powder coated) of make Jindal with 4 mm thick glass sheet with sun control film to glass shutter aluminium wire meshi complete all as specified & as directed.

M&Lfor 20 mm thick granite (table moulded & polished in window cill, jambs, steps etc over 15 mm thick screed bed in cm 1:4 in pointing with white cement with using (1:2) masble dust and admixture of pigments to match the marble shade colour complete all as specified.

M&L for complete removal of existing treatment of wall and prepartion of surfaces apply 3 mm thick Birla wall care putty & apply two coat oil bond distemper over a coat of primer complete all as specified .

All as per sl item above but on ceiling surface.

M&L for preparation of new wooden surfaces over 10cm width on girth and applying two coats of sythetic enamel paint over coat of pink primer complete all as specified and directed

S& F .150 mm long aluminium anodised barrel type tower bolts of extruded section and fixed with metal screws compete

S&F stainless steel but hinges of size 100mm long fixed to door shutters with metal scres complete

S&F 150mm long, aluminium alloy handles anodised and fabricator type and fixed with metal screws etc complete.

S&L 300mm long aluminium alloy anodised sliding door both with hasp & staple for locking arrangements fixed with nut bolts & screews etc complete all as specified.

M&L Door closer hydraulically regulated, of aluminium in extructed section body designation No 3 universal type suitable for door shutters of 891 to 100mm in width & weight between 61 to 80 kg complete all as specified & directed as.

S&L 150mm long floor door stopper of aluminium alloy body & tongue anodised with land drawn steel spring complete.

M&L for preparation of wall new plastered surface & applying 3 mm thick wall care putty & two coats of oil bound distmeper over a coat of primer complete all as specifed as directed .

S&F vitreous china urinal full stall type full white flat back and fixing plugs, beelding urinal, 60mm long brass scres fixing to flush pipe, gratings and union for discharge pipe also provide urinal spreades and PVC connection PTMT of 15mm dia bose pipe complete

S&F Vitreous china wash hand basin of size 600x 450mm flat back incl cutting for & pinning in ends of crackets or erecting stand with 15mm dia 60xe pillar tap fancy type, capstan heads, screwed and down for high pressure & also provide 40mm dia waste cerpling of PTMT

S&F 75mm dia bore PVC (SWR) pipe bends in any radious

S&F 75mm dia bore PVC (SWR) floor trap plain with greating incl jointing with cement solvent complete all as specified.

S&F 75mm dia bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor etc complete

S&F 20mm dia bore GI tubing medium grade with all fittings fixed to wall & ceiling or laid on floor etc complete all as specifed

M&L for coloured glazed tiles 350x250x7mm / 450 x 350 x 7mm thick in dado/ skirting ,set and jointed in neat cement slurry & pointed in coloured cement to match & fixing tiles over 15 mm thick rendering in cm 114 on walls

M & L, for Non skid ceramic tiles Coloured 7 to 8 mm (square) in area of each tile exc 0.06 sqm & n-exe 0.11 sqm in floors etc set and jointed in neat cement slurry & pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 .

Dismantling of aluminium portion with particle bounded glasses same hase fixed other as per the users direction & making good to distruibted surface

S & F anodesed snap grid frame work for ceiling & provide hangers 6 mm @ 1.20 m c/c adjusting level & fixed roof slab by using ms flat 40x3 mm & 60 mm long & provide 12 mm thick particle board of size 60x60 cm for in sulation as in ceiling

S & F solid PVC door frame size 47x50 mm made out 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified & directed

S & F factory made solid PVC door shutter 30 mm thick style consisting of frame made out of MS Tubes for MS Tubes for top & bottom rails ms frame shall be corosed with heat moulded plain colour PVC sheet strip of 20 mm width struck inside with solront cement for style etc complete all as specified & directed

S & F 100 mm dia bore CI pipe, soil vent or waste in any length with cement joints laid in trenches, floor or in wall etc competes.

S & F 100 mm dia bore CI pipe, bends any radious diminshing pieces or stopper

S & F viterous chana wash down water chiset with prior s tray (EWC) complete with 10 ltrs capicity PVC valveless syphonic action type flushing cistern low level while with in let ball valve float & handle &b brackets etc with PVC black seat cover closed pattern with flat bottom & ms screw CP or aluminised hinging divice.

S & F 15 mm dia bore fancy CP stop valves copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for unieers

PART -II ( E/M PORTION) Taking down carefully aluminium / copper point wiring complete (light, fan socket & power) including unserviceable fixtures and fittings such as switches ceilimg roses pendents regulators sockets light fittings etc complete removing material to store for keeping in safe custody for taking credit & making good disturbed wall / floor etc complete all as directed by Engineer-in-Charge.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including modular cover plates and modular flush boxes, Plate for mounting for housing the switches, socket outlets, fan regulators etc, all as specified and as directed. (a) One light point/ fan point/ bell point controlled by one way switch

(b) One socket point 6 Amps on same board

(c) One socket point 6 Amps on independent board

-- Ditto --- all as per item Sl No 2 above but with 2.5 sq mm PVC insulated cable and 2.5 sq mm as earth wire for 16 amps socket outlet on independent board

S&F modular switch single pole,one way 6 Amps capacity

S&F modular switch single pole,one way 16 Amps capacity

S&F modular socket, outlet 2 in 1, 6 Amp capacity

S&F modular socket, 6A/16A 2 in1, 16 Amp capacity

S&F fan Regulator step down 120 Watt

S&F of ceiling rose, surface bakelite, 65 X 50 mm, 3 terminals complete all as specified and directed.

Taking down carefully ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan, replacement of fan condensor 2.5 Mfd and painted with synthatic enamel white colour paint by spray machine including filling of cavities with filler material complete all as specified and as directed.

S & F for ceiling fan down rods 1.0 M Long of 15 mm dia GI pipe to the existing trusses of any height including necessary welding & fixing with clamps and nut bolts etc complete all as specified and as directed.

M & L for taking out Split type air conditioner indoor and outdoor unit complete with copper tubing of any size and make for shifting at other place after making necessary opening size, cutting of wall any type/ thickness and fixing of AC after necessary servicing, GAS Charging making suitable arrangement for fixing of AC complete all as specified and directed

Supply only capillary tube special annealed double wound copper tubing suitable for 1.5/1.8/2 ton window type air conditioner of diameter 0.25 " bore as per existing complete all as specified and directed.

Supply only capillary tube special annealed double wound copper tubing suitable for 1.5/1.8/2 ton window type air conditioner of diameter 0.38" bore complete all as specified and directed.

Supply and fixing Single pole and neutral enclouser with two pin and earthplug and socket complete with one single pole MCB with 240 V 20 AMPs.

S & F for recess mounted 2' x 2' square LED panel 36 watts, 596 x 596 x 9mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed. Make- Bajaj Cat part No - BCTBLR 36W FP WHN or its equivalent in Wipro, Philips, Havells.Wipro Cat no - CRCO10R038HP57GL1

S&F LED Batten for LED tubelight channel 18 watts fitting with necessay brackets complete with bipin holder, internally prewired and with connected with three core twisted flexible copper cable with suitable size 23/0.0076 and fix on 02 Nos PVC Square box (100mm X 100mm size) etc complete all as specified & directed. Make :-Bajaj Cat part No. - BLRB-RB 118/ Havells Cat Part no. - REGALBATTENT8UPTO1X22WSSBSWH/ Crompton Cat Part no - GIP131LT8-16 or other

S & Fix LED tube light Rode 18 watts with necessary fixing arrangement etc complete all as specified and directed by Engineer-in-charge. Make- Bajaj Cat Part no - BLRB-DB 18CW LED/ Havells cat part no.- PHOTOULTRA + 1213T8SSTL18WLED865SPC/ Crompton Cat Part no- LT8-20-865-2 or other.

S&F LED tube light fitting 1X10 watt,230 volts,environment friendly energy efficient with LED tube complete with bipin holder, internally prewired and with connected with three core twisted flexible copper cable with suitable size 23/0.0076 and fix on 02 Nos PVC Square box (100mm X 100mm size) etc complete all as specified & directed. Make:- Bajaj Cat no - BCLSB10WH Havells Cat part no. LUMILINEPLUSBS10WLED865SPCSS/ Jaquar Car Part no.- LGLZO1X010XW

S&F LED/CFL Bulk Light fitting, 10 watt, 230 volts, complete with all accessories pre-wired,ceiling cutting and including connecting up with twin core twisted flexible copper conductor cable with suitable size. all as specified & directed. Make:- Bajaj/Wipro/Fortune ARRT/ Havells.

S & F for plastic body exhaust fan, AC single phase, 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make - Bajaj Cat Part No -Maxma DX 8" or its equivalent in Crompton/Havells.

S&F Heavy duty Exhaust fan AC single phase 230 volt of size 300mm ,900 RPM sweep with louver and arrangemant complete all as specified & directed. Make:- /Havells Cat part no. - Turbo jet SP/ Bajaj/Usha.

M&L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC casing and capping with its accessories all as specified and directed by Engr-in -charge for the following (a) 2x4.0 sq mm and 1x4 sq mm as earth wire

PART -III ( BLDG BY NEW CONSTRUCTION) Excavation in trenches not exc 1.50mtr wide and not exc 1.50mtr in depth for foundation etc and getting out in hard / dense soil.

All as per item No-2 above but exc 1.50m deep or part thereof in depth beyond the first 1.50m.

M&L for cement concrete (1:4:8) type D2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as foundation beams,plinth beams,bases for Columns,etc;basement slabs, under-reamed piles and mass concrete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as columns,pillars,piers,posts and struts all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as slab supported on walls,beams and column I floor roofs,and in shelves etc. all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as as in beams,cantilevers,lintels,over 1.5 m span all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as as in chajjas and like all as specified and directed.

M & L for treating the backfill in contact with the foundation at the rate of 7.5 Ltrs of anti termite emulsion per Sqm of vertical surface.

M & L for treating the top surface of filled earth and soil under plinth protection at the rate of 5 Ltrs of anti termite emulsion per Sqm of surface.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 lit of emulsion per meter of the perimeter wall

Excavated soil filling under floors including spreading and leveling in layers n exc 25cm thick and well ramming including watering complete.

M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base

M&L for hard core of broken boulders of gauge n. exc 63mm, deposited, spread and levelled and layers n. exc 15 cm thick waterd and rammed to a true surface all as spd and directed

M&L for 75mm thick PCC 1:3:6 type C-2 (40mm graded stone aggregate) , without using extra cement as in plinth protection and path etc complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type D1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6, complete.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips.

All as per item No 17 above but 8mm dia

All as per item No 17 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) for rough finished surface of concrete.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, rafts raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed.

M&L for formwork to sides of pillars,posts ,struts,piers,columns and stanchions for rough finished surfaces of concrete square and rectangular all as specified.

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified.

M&L form work to edges of concrete flats, treads breakin in floors, window cill, chajja,roofs slabs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5 but not exc. 10 cm wide complete all as specified

S & F pressed steel frames for doors with one or more rebates incl necessary hold fasts, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm.

S & F 35mm thick flush shutter solid core construction with black board core, plywood face panels on both sides, etc both faces covered with decorative face veneer with liping/frame to match complete all as specified and directed complete all specified and directed

S&F aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 250 mm.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long.

S&F butt hinges 100mm size stainless steel medium weight all as specified.

S&F aluminium handles, anodised, cast type, of size 150 mm

S&F steel rolling shutter 1.25 mm thick of laths including Top cover , anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete , gear operated type with baved gear box and crank handle.

M&L for two coats of aluminium paint on new steel surfaces

M&L for preparing New surfaces , plastered or unplasterered and applying two coat of external emulsion paint over a coat of primer on walls/fins/fascia/ceiling etc including necessary scaffolding etc all as specified.

M&L for applying two coats of OBD, white over a coat of primer tinted, over 3mm thick wall care putty all as directed .

M&L for preparation of new plastered or unplastered ceiling surfaces and applying three coat of white wash as specified and directed by Engr -in-Charge.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer.

S&F framed work such as grills, gratings etc, with ends of bars shouldered and or riveted or ferged into spikes, framed guard bars

M&L rendering 5 mm thick in CM (1:3) on concrete surface in ceilling finished even & smooth w/o using extra cement.

M&L for Rendring 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 on walls ,finishing surfaces even and smooth w/o using extra cement.

M&L for 15 mm thick rendering in CM 1:4 in two coats (10+5mm) over concrete /Brick/PCC Block surfaces mixed with water proofing compound @ 3% by weight of cement, finishing even and smooth without using extra cement complete all as specified. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

Supply only WPC conforming to IS 2645

M & L for APP based polymeric membrane minimum weight 3 Kgs/Sqm and minimum 3 mm thick reinforced with polyster non-woven fabric ( wt not less than 150 gms/sqm) laid over primed surface with bituminous primer conforming to IS- 3384 @ 0.3 litre/sqm and finishing with preventive coat with aluminium paint @ 100m/sqm all as directed and specified.

Returning filling in including spreading, levelling, watering & well ramming in layers n.exc 25cm each.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed.

M&L brick work half brick thick with sub class ‘B’ old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:4.

M&L for 20mm thick granite of any type table rubbed and polished as in steps,jambs,pillars, window cills cooking platforms etc and like in cement mortar 1:4 including pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete

M and L for coloured Non skid ceramic tiles7 to 8 mm thick (st noquare/rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed bed in cement mortar 1:6.

M and L for coloured Glazed ceramic tiles 300X200mmX7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10mm thick cement screed in 1:4.

S&F viterous china flat back urinal bowl type of min size 465x355x265 mm, white, with grating and union of discharge pipe including connection to flush pipe and out going pipe, fixed in repair complete

S&F Vitreous china wash down water closet white pedestal pettern white

S&F plastic water closet seat back closed pattern with flat bottom and cover mild steel chromium plated hinging divice fixed complete.

Supply and fixing faucet health (hand jet) 15mm bore with fittings, mplete all as specified and directed.

Supply and fixing Chromium plated jet spray with CP connection pipe for EWC 15mm bore with fittings, complete all as specified and directed.

M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete lived in repairs and making good to floor complete.

S&F Cromium plated brass bib cock ,cast copper alloy with capston headed handle, screwed down screwed for iron pipe or for brass ferule of 15mm dia all as spd and directed

S&F Stop valve cast copper alloy screwed down high pressure with capstan head, handle chromium plated angular type screwed both ends for iron pipe 15 mm bore or for unions complete.

S&F Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 15 mm .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 20 mm .

S&F of 110mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joint fixed to walls

S&F of 75mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joint fixed to walls

S&F PVC (SWR) junction double ( single T) of size 110mm bore jointing with solvent cement

S&F PVC (SWR) reducer 110mm to 75mm bore jointing with solvent cement

S&F PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 63 mm outlet dia complete

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete.

S&F soap dish any type fixed type fixed to plugs with chromium plated brass screws complete

Supply only 20mm bore ball vavle high pressure of PTMT with epoxy coated aluminium road and high density platic ball screwed for iron pipe and fixed all as spd and directed

S&F 500 litre capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closet top hoisted and fixed in position all as specified in SSR (2009) Part I complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification.

Supply only 3mm thick frosted one side sheet glass ordinary quality in square n exc 0.5 sqm each pane in new glazed shutter all as spd

S&F brass chromium plated tubular towel rail 20mmdia complete all as specified and directed

S&F wash hand basin vitreous china (flat back) any size including cutting for and pinning in ends of brackets complete size (550 x 400mm )

M&L for 150 mm bore salt glazed stone ware drain pipes of grade 'A' laid in trenches and jointed and tested complete all as specified.

M&L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in concrete bed to drain pipes 150mm bore including packing under and hunching against the sides of pipes after they are laid and tested in complete all as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and refofming benching as required.

M&L for Steel work in tublar trusses incl spl shaped washer etc using ERW or induction buttt welded tubes conforming to I S 1161-1979 grade st-240.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F for Steel ventilators with top hung shutter including hinges, steel peg stay , complete.

PART -III (SPECIAL ITEM OF WORK) M&L joint free Vitrified tiles coluored dark shade of 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including provision of screed bed 15mm thick in CM (1:4) complete all as spd & as directed.

As per item no 83.00 but as on vertical surfaces incl 10mm thick rendering in CM 1:4 -do-

S&F Venition blends with design on inner/outer face roll down type made out of fibre cloth fixed, to wall with necessary Aluminium brackets, screws etc including Alluminium frame for venilion blinds etc all as approved by GE all as specified and directed. Make : Vista and Levador or Equivalent

S&F aluminium windows of sliding type with standard aluminium section (thickness of powder coating not less than 50 micron) with 5.5mm thick tinted glass with sun control film to glass shutter out side and aluminium wiremesh inside fixed on 3 track aluminium section with locking arrangement, handles etc all as specified.

PART -III (SITE CLEARENCE AND DEVELOPMENT) Surface dressing n. exc.15 cm deep in soft/loose soil

PART -III (INTERNAL ELECTRIFICATION) M&L for Point wiring complete with multistranded copper conductor cable (ISI marked) 1.5 Sqm PVC insulated, unsheathed cable 1100 volts FRLS grade drawn through in and including concealed non metalic rigid PVC conduit and all accessories such as bends, tees, junction boxes etc, concealed conduit in walls / roofs / ceiling etc.and including provision of continuous earth wire of size 1.5 Sqmm copper conductor PVC insulated unsheathed connected to earth dolly, Including terminated in terminal box made out of 1.60 mm thick MS sheet concealed in walls and including Metal flush box with Modular white cover plate and top as per site requirenment for housing the switches, socket outlet, fan regulator etc, cutting chases and making good to disturbed surface complete for the following :- (a) One light point controlled by one 6 Amps one way switch.

b) One ceiling Fan, Exhaust Fan point controlled by one 6 Amps switch.

(c) One 3 pin switch socket outlet point 6 Amps on independent board.

(d) One 3 pin switch socket outlet point 6 Amps on same board with other switch.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size.

S & F modular switch1 way 6A, 1 module

S & F modular switch1 way 16A, 1 module

S & F socket out let 6A 2/3 on combined 2 module

S & F socket out let 6A/16A-2/3 pin combined 2 module

S & Fix ceiling rose surface backlite 65x50mm 3 terminals complete.

S & F fan regulator electronic 2 modular type volts AC 50 HZ ,100 Watts,4 step complete all as directed.

S & Fix Baton for LED tube light 18 W with tube rod with complete accessories all as specified and directed by Engr-in- charge.Make Bajaj,Code no-112181, Cat no-BLRB-DB 1x18W

S & Fix Fans ceiling complete with one electronic type regulater and accessories 230 volts,1200 mm sweep(white colour), 5 star rated complete all as specified & directed. Make : Havells,Bajaj and Usha

S & Fix exhust fan, 300 mm sweep, working on AC single phase, 230 volts, with louver shutter. Make : Havells/Usha/ Bajaj

S & Fix LED street light 30 W CUB type building security light pressure die cast aluminium housing LED street light lumaniries with IP 66 and complete accessories all as specified and directed by Engr-in-charge Make- BAJAJ Cat No-169887, BCLST 30W LED I or Eqvt in other

S & Fix of bracket / arm for street light fiting made out of 40 mm dia GI pipe not exceeding 2.5 mtr long complete accessories including fixing of MS clamps 2 Nos nut and bolts complete as directed.

S & Fix in replacement of 2 runs of 1.5 Sqmm PVC insulated stranded copper cable for connection of building street light including PVC conduit 20 mm external dia medium grade fixed on building with proper clamping, saddling etc all as directed.

S & Fix of sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 100 ampere rated bus bar, 415 volts fixed sunk/flush to the wall or niche complete all as specified and directed.

S & Fix of MCB single pole and neutral, 240 volts, 40 to 63 Amps, rupturing capacity 10 KA, ‘B’ series complete all as specified and directed.

S & Fix of MCB single pole, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘B’ series complete all as specified and directed.

PART -III ( EXTERNAL ELECTRICAL SUPPLY) Supply and Laying and testing cable XLPE insulated heavy duty electric cables with aluminium conductor, 1100 volts grade, cross sectional area 16 sqmm, 2 core cable connecting lugs, glands, jointing materials etc, laid on wall, floors, roof, ducts and fixing using clamps, saddle complete all as directed by Eng-in-charge of following:-

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth and getting out in Hard / dense or any type of soil including forming bottom surface etc.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 50 mtr above the starting point.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement.

M &L for GI pipe ''light grade'' for road crossing / on wall / on pole for cable protection of following size:- Make: TATA/JINDAL/ PRAKASH SURYA a) 50 mm dia

M&L for earthing complete with galvanised steel earth plate electrode 600 X 600 X 6mm thick buried directly in ground (earth pit not less than 2.25M deep below ground level) with top edge of the plate not less that 1.5M below normal grouond level connected to GI earth wire 4mm dia by means of nuts, bolts, check nuts, washers of galvanised iron or steel all as shown in electrical plate No 03 of SSR Part-I connected to earthing test point / DB including excavation / earth work in any type of strata, removal of surplus earth, GI pipe for watering pipe withand funnel, PCC 1:3:6 Type C-1 chamber with 40mm thick RCC 1:2:4 type B-1 in cover slab with TMT bars @ 150 mm c/c both way with GI protection pipe complete all as specified and directed by Engineer-in-Charge.

PART -IV( PROVN OF SLIDING WINDOWS IN CONFERENCE HALL) Taking down chowkats or frames with shutters (without taking off shutters from the frames exc 1.5Sqm but n.exc 4 Sqm each.

Rendering 15mm thick on fair faces of brick wk or concrete surfaces in CM 1:6 and finished the surface even and smooth (without using extra cement)

M&L for two coats of OBD over a coat of primer including prepartion of new surfaces on walls

S&F anodized aluminium window three track with window frame using aluminum section 92x31.75x1.5mm thick and shutter frame using aluminium section of size 40 x 18 x 1.29mm thick with 5mm thick black plain tinted glass in shutter and one masqito proofing shutter including necessary fittings, handle aluminium 75mm for each shutter, locking arrangement, rubber gasket (ring) & making good to the disturbed portion (with Powder Coating minimum Thockness of powder coating 50 micron).etc complete. Make of aluminium section Jindal, Hindalco or equivalent and glass make Saint Gobian, Modiguard.

PART- V ( PROVN OF SLIDING WINDOWS AT TECH AREA ) S&F anodized aluminium window three track with window frame using aluminum section 92x31.75x1.5mm thick and shutter frame using aluminium section of size 40 x 18 x 1.29mm thick with 5mm thick black plain tinted glass in shutter and one masqito proofing shutter including necessary fittings, handle aluminium 75mm for each shutter, locking arrangement, rubber gasket (ring) & making good to the disturbed portion (with Powder Coating minimum Thockness of powder coating 50 micron).etc complete. Make of aluminium section Jindal, Hindalco or equivalent and glass make Saint Gobian, Modiguard.

Part VI ( PROVN OF WALL MOUNTED FAN AT ADMN BLDG) S & F Wall mounted fan 400 mm sweep along with necessary fixing arrangemnt as per manufacturer standard and making good disturbed surface etc. included in quoted rates, all as directed by Engineer-in-Charge. Make:-CG Cat No WMSDX 120 or equivalent in Bajaj/Wipro

Point wiring with 1.5 Sqmm PVC insulated and unsheathed cable 1100 Volts grade with multistrandand copper conductor drawn through and incl PVC casing capping and accessories and surfaces, on wall with and including pressed steel terminal box groutig in the wall and luminated sheet top cover for mounting of switches sockets, regulators etc incl 1.5 Sqmm PVC insulated unsheathed cable multistranded with copper conductor and connecting to earth dolly for light, fan, plug and bell. (a) One fan point controlled by one switch.

S & F ceiling rose, surface bakelite, 65 x 50 mm three terminals, ISI marked

Supply and fixing switch piano flush button type , singlepole one way 5 Amps complete all as directed.

M & L for Sub main wiring complete with 2 runs of 2.5 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn through PVC Cassing Caping and including 1 run of 2.5 Sqmm PVC insulated unsheathed copper conducter with multistranded copper conductor as earth continuity. Note : Two runs of copper conducter and one run of earth copper conducter shall be measured as one length.

PART- VII (PROVN OF WATER COOLER AT COMMUNITY HALL) Supply, installation,commissioning of Water cooler fully stainless steel, electric driven single phase having approx storage 80 litres and nominal cooling capacity 40 litres per hour.

Supply and fix voltage stabiliser for automatic operation , single phase naturaly air cooled indoor type and designed for input variation between 170 to 270 volts with out put voltage stabilised at 230 volts with accuracy +/- 1% , Operating frequency 50 Hz, Response time <3 msecs, Operating Temperature 0-55 Degree C ,Duty of operation Continuous at 100% , Rate of Correction 15 to 40 V / Sec and of capacity 2 KVA, Make: V Guard/ M Guard

M & L for Sub main wiring complete with 2 runs of 2.5 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn through PVC Cassing Caping and including 1 run of 2.5 Sqmm PVC insulated unsheathed copper conducter with multistranded copper conductor as earth continuity. Note : Two runs of copper conducter and one run of earth copper conducter shall be measured as one length.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20A capacity

3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. of size 16mm dia

Supply and fixing stop valves, cast copper alloy, secrewed down, high pressure with crutch or butter fly handle, fancy type, screwed both ends for iron pipe or for unions and fixed of size 15mm dia bore

S & F hose pipe 25mm for drain of water cooler 1.5mtr long all as specified and direced

Supply and fix PVC Connection 15mm dia 450mm long

M&L for PCC 1:2:4 type B-2 with 20 mm graded aggregate for capping of pole / transformer plateform complete all as directed.

PART -VIII (PROVN OF DESERT COOLER AT R&A GROUP) Supply and fix desert cooler electric driven (single phase), having nominal air flow capcity not less than 2000 Cum per hour, tower type plastic/PVC Body, empty water tank alarm system, 5A plug top for connection etc all as directed by Enginner-in-Charge of Make- Symphony Cat No Symphony Diet 50i Tower Air Cooler or equivalent in Usha/Bajaj

sagar construction

M/S P D TUPE