SPECIAL REPAIR TO BLDG NO 244/01 TO 04 AND PROVN OF CERTAIN SANCTIONED WORKS UNDER AGE B/R-I AT ITARANA, ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed by Engr-in-Charge.

Demolition of cement concrete (un-renforced) in ground floor and paving. exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified& directed by Engr-in-Charge.

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store.

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame n. exc 1.5 sq. m each & removing to store.

Taking down shutter of any descriptioon exc 1 Sqm but n exc 2 Sqm each.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

Taking down cement plaster any description on brick or stone any description complete all as specified& directed by Engr-in-Charge.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

Dismantling/demolition water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

M&L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6m radius, built in CM in 1:6 complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks in one brick thick honey comb walling, built in CM 1:4 complete all as specified and directed.

M&L solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

M&L factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified& directed by Engr-in-Charge.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified& directed by Engr-in-Charge. Make Pioneer,Surbhi metal, A-1 Teak

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified& directed by Engr-in-Charge.Make Pioneer,Surbhi metal, A-1 Teak

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws fixed in repair.

S&F sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane3mm in thickness complete all as specified& directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified& directed by Engr-in-Charge.

S&F butt hinges 100mm long medium weight, stainless steel complete all as specified& directed by Engr-in-Charge.

S&F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engr-in-Charge.

S&F 150mm 'D' type aluminium handles, anodised complete all as specified & directed by Engr-in-Charge.

S&F MS pressed bow handle of 150m size oval type stove enamelled black & fixed complete all as specified.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long complete all as specified.

S&F MS barrel tower bolt 200 mm long stove enamelled black with bright bolt & fixed complete all as specified.

S&F MS sliding door bolt with hasp and staples type, 300mm long stove enamelled black with bright bolt not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple plate and fixed all as specified.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges steel peg stay etc complete including taking down.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item No 35.00 above but without glazing bar.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

Cutting holes in brick/stone walls n. exc. Half brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed

S&F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs drapery curtain rod of metalic 25mm dia covered with PVC coating complete with MS bracket golden colour rings as required at site and side caps fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), 25mm thick, as in Sub base complete all as specified & directed by Engr-in-Charge.

M&L non skid ceramic tiles 7 to 8mm thick(square/rectangular) colored tiles area of each tiles exc 0.11 sqm but n.exc. 0.18 sqm in floor set and jointed in neat cement slurry and pointed in white or coloure cement and over 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-in-Charge.

M&L 75 mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified& directed by Engr-in-Charge.

M&L glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engr-in-Charge.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete.

M&L machine cut kota stone riser steps skirting dado slab flooring 20-25mm thick over 20mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified& directed by Engr-in-Charge.

M&L plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in landing, chajjas, shelves and similar articler as directed including necessary formwork/ scaffolding complete all as specified& directed by Engr-in-Charge.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 48.00 above but 6 to 8 mm dia TMT bars.

All as per item No 48.00 above but 5mm dia and over upto & including 10mm dia in stirrups, spaces & binder.

M&L 15mm thick cement plaster in two layer first coat in CM 1:6,10cm thick & second layer 5mm thick in CM 1:4 mixed with WPC 3% by weight of cement including finishing fair & even on brick or concrete surfaces of othern tna fair faces.

M&L rendering 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L rendering 15mm thick in CM 1:4 on brick or concrete wall surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound (water proof compound paid seperatly) all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in CM 1:4 including water proofing compound @3% by wt of cement on roof slab while the slab is green

Supply only Integral waterproofing compound.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

M&L preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed by Engr-in-Charge.

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified & directed by Engr-in-Charge

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete all as specified & directed by Engr-in-Charge.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 450mm x 300mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed by the Engr-in-charge.

S&F in repair stop valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed by Engr-in-Charge.

S&F in repair stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed by Engr-in-Charge.

S&F 20mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete all as specified and directed.

S&F soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 3330mm x 160mm complete all as specified and directed.

S&F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580mm x 440mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing surface all as specified and directed.

S&F vitreous china wash down water closet (Pedestal pattern) white with 'P' or 'S' trap (excluding flushing cistern and flush pipe) including provision for fixing including Plastic water closet seat white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device etc complete

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion complete all as specified.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed by the Engr-in-charge.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as directed by the Engr-in-charge.

S&F for stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls including removing the old pipes and making good the disturbed surface as per existing complete all as specified & directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) junction single(Single T) equal or unequal 75mm dia complete all as directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified & directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

Demolition mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge.

M&L screed laid 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified& directed by Engr-in-Charge.

Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr /10 sqm with a thickness of 650micron Note: 6 Hrs interval between two coats will be maintain& the work will be carried out through company applcator duly got approved from Accepting officer in writing before incorporation and paid only after receiving of the warrenty certificate from the company. Make : Asian paint or equivalent as approved by GE Note : The treatment shall be carried out by authorised applicator approved by GE as per the manufacturer instructions.

M&L 75 mm thick PCC(1:4:8) type D2 (using 40mm graded stone aggregate ) as in sub base complete all as specified& directed by Engr-in-Charge.

M&L for 25mm thick Sand cushioning under floors complete all as specified and directed.

M&L 60mm thick machine pressed precast conctete interlocking rubberized paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade complete all as specified and as directed by Engr-in-Charge.

M&L PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified& directed by Engr-in-Charge.

M&L Plain cement concrete 1:3:6 type C-1 (using 12.5 mm graded stone aggregate) set in cement mortar 1:4 as in kerb blocks with plain fair faces including chamfered weathering throating etc complete all as specified& directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 Cu.m, getting out in soft/loose soil and removing surplus soil to a distance n exc 50m complete all as specified and directed.

Cutting holes in brick walls Exc half brick but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 TYpe B1 as required complete all as specified and directed.

M&L for Cement Concrete type C 2 1:3:6 using 40 MM graded stone aggregate as in foundation filling and mass concrete in fixing of fencing post including necessary form work if required at site complete all as specified and directed.

M&L for precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:6 complete.

S&F stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. to confirming to IS 116-1979 grade (medium grade all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 pigmented stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden attens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demelotion of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqm on plan area and getting out in soft/loose soil all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

Returning, filling in including spreading, watering & well ramming in layers n exc 25 cm thick complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, broken stone boulder deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 75 mm thick PCC 1:2:4 type B-2 using 40 mm graded aggregate as in flooring finishing cement concrete even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L providing and laying bitumen mastic wearing course (as per specifications) with industrial bitumen of grade 85/25 conforming to IS:702 prepared by using mastic cooker and laid to required level and slope including providing anti skid surface bitumen precoated fine grained hardstone chipping of approved size at the rate of .005 cum per 10 sqm and at approximates spacing of 10cm centre to centre in both directions pressed into surface protruding 1mm to 4mm over mastic surface,including cleaning the surface ,removal of debris etc,all complete (Considering bitumen using 10.2% as per MORTH specification) 25mm thick all as specified and directed by Engr-in-Charge. Note : Work will be carried out by the authorised applicator as approved by the Accepting Officer before incorporation.

M&L for reinforcement cement concrete work (Nominal Mix) Type B-1 1:2:4 (20 mm graded stone aggregate) as in foundations, including rafts footings, foundation beams; plinth beams, bases for columns etc; basement slabs, under-reamed piles and mass concrete

All as per item No 117.00 above but in column.

All as per item No 117.00 above but as in roof, floor,shelves, slabs supported on walls, beams and columns in floors

All as per item No 117.00 above in before but in chajjas.

All as per item No 117.00 above here in before but as in lintel, beams plinth beams etc.

M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed.

M&L for form work to chajja for rough finished concrete surface complete all as specified and directed.

M&L for form work to side and soffit of roof beam etc for rough finished concrete surface complete all as specified and directed.

M&L for formwork for flat rough finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, side and soffits (if any) of foundation and plinth beams and similar works, vertical or to batter.

M&L for formwork for flat rough finished to sides of concrete pillars, posts, struts, piers, columns and stanchions as square, rectangular or polygonal sides.

M&L for form work to sides for slabs and sides of RCC/PCC bands in walls, horizontal or sloping and SImilar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed.

M&L for MS framed guard bars conforming to Fe-410-0 or Fe-310-0 welded to steel windows/ventilations complete all as specified and directed.

S&F mild steel work confirming to Fe-310-0 or Fe-410-0 in hold fasts to flat iron cut to length, bend to shape incl preparing surfaces and trated with tar and sanded with clean sharp and complete as in hold fast wind etc.

S&F WHB flat back of size 580mm x 450mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete.

S&F CP coupling 32mm dia for WHB with long screwed end and fly nuts flanged and bedded in red lead cement.

S&F 20mm dia stop valve of copper alloy screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed.

S&F vitreous china urinal, bowl type flat back of size 465x355x265 mm white with grating and union for discharge pipe down take pipe etc.

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate) in bed to drain pipe including packing under & haunching against the SIdes of drain pipes after they are laid and tested complete for 150mm bore pipe all as specified and directed by Engr-in-Charge.

S&F salt glazed stone ware drain pipes grade 'A' ISI marked laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified for 150mm bore of pipe.

M&L for 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified.

S&F 4mm thick sheet glass of figured,pin headed and glazing with oil putty in square n exc 0.50 sqm in each.

M&L preparation to new or previously untreated wooden surface of any description,over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F MS barrel tower bolt 150mm long stove enamelled black with bright bolt & fixed complete all as specified and directed.

M&L precast kerb stone built in PCC, type B1, 1:2:4, using 20mm graded stone aggregate and fixing in CM 1:4 all as specified and directed by Engineer-in-Charge.

PCC (1:2:4) type B-2 using 40mm graded stone aggregate as in channels of man holes complete all as specified and directed.

Loose filling of broken brick of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

Cutting of exising 150 mm dia manholes/septic tanks for connecting new drains making good to pipe and rendering cutting out exising benching for and forming benching for and forming branch channel (1/2round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified directed by Engr-in-Charge.

M&L rendering 10mm thick in cm 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L rendering 15mm thick in cm 1:4 on other than fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for providing cement concrete type B1, 1:2:4 (20 mm graed aggregate) as in copings complete all as specified and directed.

M&L for damp proof course 40 mm thick, in cenment concrete 1:2:4, type B-0, to horizontal or vertical complete all as specified and directed.

M&L PCC 1:3:6 type C2 using 20 mm graded stone aggregate as in surface channel/drains etc complete all as specified and directed.

Extra for forming fair finished drain or channel exc 30cm inner girth in cement concrete using extra cement including forms moulds mitred/stopped ends etc. complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in CM(1:4) with joints to match complete all as specified and directed.

M&L precast cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate set in CM(1:4) louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed.

Taking down carefully copper/aluminium point wiring for one light/socket/ power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves /dash fasteners with cadmium plated screws, all as per IS and including wooden boxes fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per item No 154.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per item No 154.00 here-in-before but for one exhaust fan point controlled by one switch and regulator.

All as per item No 154.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per item No 154.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 154.00 here-in-before but for one bell buzzer point controlled by one switch.

All as per item No 154.00 here-in-before but for one light point controlled by two, two way switches.

All as per item No 154.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, two way, 5 Amp, 230 Volts complete all as specified and directed.

S&F bell push flush type 5 Amps 240 Volts complete all as specified and directed.

S&F bell/buzzer AC 230 Volts single pole complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface Bakelite 65x50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make :- Havells Cat Part No LHEXBHP71NW018 or equivalent of Philips/ Crompton Greaves /Bajaj/Wipro.

S&F LED type security light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete all as directed. Make Havells Superb Cat part No LHEXAYP7PN6K020 or equivalent of Philips/ Crompton Greaves/ Bajaj/ Syska

S&F LED bulb 10/11 watt complete all as specified and directed. Make : Havell's/Crompton/ Syska.

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F stepped type electronic fan regulator, flush type and connecting up ISI marked 240 volts complete all as specified & directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 4 way, 240 volts complete all as specified and directed.

S&F MCB 63 Amps, triple pole & neutral, 415 Volts complete all as specified and directed. Make : Legrand/ Havells/ABB

S&F MCB 32/40 Amps, single pole & neutral, 240 Volts complete all as specified and directed. Make : Legrand/Havells/ABB

S&F MCB 6-40 Amps, single pole, 240 Volts 'C' curve, 10KA ISI marked as per IS/IEC 60898-1 2002 complete all as specified and directed. Make : Legrand /Havells /ABB

S&F sub main wiring on including passing throuh PVC conduit pipe 1100 volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 Sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 4 sqmm of green colour confirming to IS 694/1990 including taking down existing unserviceable sub main wiring. (Note : Two runs of cable with one run of earth wire and one run of PVC casing caping should measured as one length).

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5 cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawlplug (4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 25 sqmm 4 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L for brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

Disconnecting from elect connection and taking down carefully the existing electric energy meter of any capacity, any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same inside the old meter inside box carefully including necessary electric connections complete all as directed.

S&F exhuast fan complete of 300mm sweep 240V AC including provision of hole in wall of suitable size for fixing of exhuast fan complete all as directed. Make : Havells, Crompton, Bajaj, Orient.

Disconnecting from elect connection and taking down carefully the existing ceiling fan/exhaust fan/geyser of any capacity any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same ceiling fan/exhaust fan/geyser carefully including necessary electric connections complete all as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

M/s Laxmi Enterprises