MISC REPAIR TO SECURITY FENCING, BARBED WIRE, GATE AND FOOTPATHS UNDER AGE BR I

Amount

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded all around concrete portion and making good disturbed gound including removal of debris from site complete all as specified and directed.

Dismantling of fencing wire mesh of any type complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in foundation, filling, mass concrete, sub base of floors, etc complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular rough finished complete all as specified and directed.

S&F mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc.) including all necessary drilling bolting or riveting, etc, and similar work and similar conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F mild steel round bars 10mm dia and over, cut to length, bent to shape required, includinig cranking, bending spirally for hooping of columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips quality confirming to Fe-410 W complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or sguare heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or screw nut n.exc 5 cm long dia of shank 12 m complete all as specified and directed.

Supply only mild steel galvanized chain link fencing of 4mm dia wire and 75mm X 75mm mesh size complete all as specified and directed Make:-TATA/SAIL/JINDAL

Fixing only chain link fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed by Engr-in-charge.

M&L for preparation of newly steel surfaces exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly steel and iron surfaces of any description not exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide paint complete all as specified and as directed.

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Surface dressing n exc 15 cm deep and getting out in soft/loose soil etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in coping to lower portion of chain link fencing including work to sides of concrete surfaces etc complete all as specified and directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for cement concrete 1:4:8, type D 2 (using 40 mm graded stone aggregates) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3 type A 1 (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3 type A 1 (using 20 mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed.

All as per Srl item No.19 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders -ditto-

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; ; clamps; hold fasts; wall ties; hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters;and similar small articles conforming to Fe 290 Gde E 165 complete all as specified and directed.

M&L for brickwork with subclass 'B' old size bricks, straright or corved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work or rubbled stone masonry including all qoins arches , pillars etc built in cement mortar complete all as specified and directed.

S&F ornamental and decorative type steel gate with structural steel conforming to Fe 290, Gde-E-165 all as specified, revolving on bearing plate including pintal hinges fixed on pillar in PCC blocks of size as required as site , including all locking arrangement, all as per sample approved by the Engineer -in -Charge and dirceted and fixed in position Note :-1 . The weight of manufactured steel gate shall be measured before fixed in position . Necessary arrangement for weighing the steel gate shall be made by the contractor at his own expense . The contractor shall quote the unit rate accordingly. 2. Steel gate shall be manufactured as per sample approved by the GE

M&L for coloured designer glazed ceramic tiles of size 450mmx300mmx7mm to 8mm thick on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match and laid over and including 10mm thick rendering in CM 1:4 complete all as specified and directed

M&L for 18 mm to 20 mm thick granite slab (table rubbed and -polished ) , machine cut, laid over and including 15 mm thck cement plaster in CM (1:3) on vertical surface of wall, pillars etc and jointed witht grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing edges to be rounded including dismantling of old exisitng stone or flooring of any description & removing rubbish outside MOD land complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floor of pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for hardcore of gauge n.exc 63 mm, with broken stone or boulderes deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified & directed.

S&F machine pressed precast cement concrete coloured chemically treated rubber moulded interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658 - 2006 of 60mm thick, M-35 grade complete all as specied and directed.

M&L for crushed quarry stone dust filing under floors or in foundation or cusion bed to lay under paver blocks complete all as specified and directed

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in sub base concrete complete all as specified and directed.

M&L for forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as specified and directed

M&L for rendering 15mm thick cement plaster in cement mortar 1:4 on fair faces of brick /Concrete surfaces finishing the surfaces even and smooth with out using extra cement etc complete all as specified and directed and directed.

M/s Mohan Singh

A Raza Enterprises

M/s AJAY JAIN

m/s shivansh traders