Loading
Loading…
Loading…
Tender Value
₹55.0 L
EMD Value
₹1.1 L
Closing Date
16 Feb 2026, 4:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECT.G
17 conditions · 5 needing a document upload
Financial Eligibility Criteria: (Ref: RB letter No. 2022/CE-I/CT/GCC- 2022/POLICY : Advance Correction Slip No.-1 dt 14.07.2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The intending tenderers should possess a valid electrical contractor license at the time of opening of tender, issued by any state government & same should be submitted along with tender documents by all bidders including working contractors of this unit otherwise offer shall be summarily rejected....... IT SHOULD BE NOTED BY THE TENDERER THAT ELECTRICAL LICENSE UNDER RENEWAL AT THE TIME OF TENDER OPENING WILL NOT BE CONSIDERED AND OFFER WILL BE SUMMARILY REJECTED. IT IS THE RESPONSIBILITY OF TENDERER TO UPLOAD VALID ELECTRICAL CONTRACTOR LICENSE ON THE DATE OF TENDER OPENING.
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
32 conditions · 4 needing a document upload
The rate to be quoted by tenderer shall be inclusive of all state/central taxes including GST. THE TENDERER SHOULD UPLOAD VALID GST REGISTRATION CERTIFICATE ALONG WITH THE OFFER.
The tender shall comply with General Condition of contract (GCC),2022 of Indian Railways (file attached). and its latest amendment, if any. The tenderer shall submit the offer after duly satisfying himself/herself with the GCC,2022 in general.
Tenderers are required to upload the Bank details as per Annexure-XII (Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT) Model Mandate Form)of tender document.
Tenderers are required to upload requisite details as per Annexure-VIIB (DETAILS OF CONTRACTUAL PAYMENT RECEIVED IN LAST THREE FINANCIAL YEARS AND CURRENT FINANCIAL YEAR) without which the offer is liable to be rejected.
Tenderers are compulsorily required to upload Affidavit as per Annexure-XXIV along with tender document, without which the offer will be considered incomplete and will be rejected summarily.
All requisite documents/credentials mentioned in clause 3.5 of the tender document attached pertaining to his/their technical and financial eligibility. (As applicable).
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenderer/s shall be treated as Null & Void.
Defective parts shall only be replaced with OEM's spares. Proper invoices/delivery challan /warranty certificate etc. shall be provided by the firm to prove genuineness of spare parts.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no. 2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.
IF ANY DISCREPANCY IS FOUND IN THE TENDER DOCUMENT, NAMELY SOR ITEM DESCRIPTION, SPECIAL TENDER CONDITION ETC., CLARIFICATION CAN BE SOUGHT FROM THE OFFICE OF SRDEE/G/DLI, DRM OFFICE, STATE ENTRY ROAD, NEW DELHI.
This tender complies with Railway Board instructions for Startups (recognized by Department of Industrial Policy and Promotion, Ministry of Commerce and Industry) for exemption from payment of Bid Security as detailed in GCC 2022 as amended from time to time. Such Startup firms may note that no other exemption is applicable to them in this particular tender.
On account payment, contractor shall submitted indemnity bond with validity up to the completion/extended period in the prescribed format (please refer Annexure-XXVIII) at the contractor's cost, vesting the ownership of such material with the railways.
Electrical work in connection with (i) "Redevelopment of Sarai Kale Khan Entry by provision of 1 set of escalator (2 Nos. UP and Down), 1 No. of Lift, rearrangement of booking office, provision of staff toilet, replacement of roof shed, extension of deck slab of existing FOB as per approved plan in connection with NCRTC and railway connection at HNZM in the section of SSE/W/HNZM under Sr. ADEN/HNZM". (ii) Electrical work for augmentation & improvement of sick-line facilities at DEE depot.
54-SRDEE-G-DLI-2025-26~NR
54-SRDEE-G-DLI-2025-26
Open
Works - General
6 Months
Delhi, Delhi
₹0
₹1.1 L
16 Feb 2026
24 Jan 2026
2 Feb 2026
109 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 55,03,240.45 | ||
| — | 5000.00 | — | — | ||
| Supply and recessing/fixing of PVC conduit pipe of 25mm size conforming to IS 9537 Part-III:1983 (or Latest version) with accessories junction box, bends etc. including making chase, plastering/clamping etc. as per site requirement & as per explanatory note. | — | — | — | 1,55,000 | |
| — | 200.00 | — | — | ||
| Supply and recessing/fixing of PVC conduit pipe of 40 mm size conforming to IS 9537 Part-III:1983 (or Latest version) with accessories junction box, bends etc. including making chase, plastering/clamping etc. as per site requirement & as per explanatory note. | — | — | — | 11,900 | |
| — | 6700.00 | — | — | ||
| Supply of following sizes FRLS PVC insulated multi stranded copper conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x1.5 sq.mm | — | — | — | 87,770 | |
| — | 5000.00 | — | — | ||
| Supply of following sizes FRLS PVC insulated multi stranded copper conductor single core cable conforming to IS 694 (or Latest Version) , and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x2.5 sq.mm | — | — | — | 90,500 | |
| — | 3400.00 | — | — | ||
| Supply of following sizes FRLS PVC insulated multi stranded copper conductor single core cable conforming to IS 694 (or Latest Version) , and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x4.0 sq.mm | — | — | — | 88,774 | |
| — | 1000.00 | — | — | ||
| Supply of following sizes FRLS PVC insulated multi stranded copper conductor single core cable conforming to IS 694 (or Latest Version) , and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x10.0 sq.mm | — | — | — | 72,000 | |
| — | 30.00 | — | — | ||
| Supply, fixing, testing and commissioning of following modules, GI box alongwith modular base and cover plate for modular switches/ sockets in recess etc as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 4 module | — | — | — | 5,760 | |
| — | 55.00 | — | — | ||
| Supply, fixing, testing and commissioning of following modules, GI box alongwith modular base and cover plate for modular switches/ sockets in recess etc as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 6 module | — | — | — | 14,349.5 | |
| — | 5.00 | — | — | ||
| Supply, fixing, testing and commissioning of following modules, GI box alongwith modular base and cover plate for modular switches/ sockets in recess etc as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 8 module | — | — | — | 630 | |
| — | 30.00 | — | — | ||
| Supply, fixing, testing and commissioning of following modules, GI box alongwith modular base and cover plate for modular switches/ sockets in recess etc as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 12 module | — | — | — | 12,750 | |
| — | 430.00 | — | — | ||
| Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 5/6 Amp Switch | — | — | — | 22,815.8 | |
| — | 85.00 | — | — | ||
| Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 16 Amp Switch | — | — | — | 7,324.45 | |
| — | 60.00 | — | — | ||
| Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 3 pin 5/6 A socket outlet | — | — | — | 6,000 | |
| — | 85.00 | — | — | ||
| Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 6 pin 15/16 A socket outlet | — | — | — | 11,934.85 | |
| — | 10.00 | — | — | ||
| Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per IS, IE rules and site requirement complete and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. 13 A universal socket outlet | — | — | — | 990 | |
| — | 250.00 | — | — | ||
| Supply of ceiling rose, 3 plate conforming to IS : 371-1999 (or Latest Version) & installation on the junction box of laid conduit including connections, testing & commissioning as per site requirement and as per Tech. Specification & as per explanatory note. | — | — | — | 18,350 | |
| — | 50.00 | — | — | ||
| Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. | — | — | — | 16,900 | |
| — | 10.00 | — | — | ||
| Supplying & recessing/ fixing suitable size GI box wih modular plate and covering front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. | — | — | — | 6,750 | |
| — | 10.00 | — | — | ||
| Supply, recessing, fixing, testing and commissioning of 63 A DP ,30 mA RCCB AC type confirming to IS 12640-1 & IEC61008-1 with 10KA short circuit withstand capacity complete with enclosure conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. | — | — | — | 27,220 | |
| — | 55.00 | — | — | ||
| Supply, Installation, Testing and Commissioning of 1400 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 245 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%,suitable for electronic regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, earthing etc. complete as required & as per explanatory note. It shall also include the scope of supply and installation of safety cord of SS as per IS:302 Part 2 Sec-80. Dia & length of such cord shall be as per recommendation of OEM of fan and same shall be approved by railway. | — | — | — | 1,55,100 | |
| — | 10.00 | — | — | ||
| Supply, fixing, testing and commissioning of 250mm sweep fresh air fan complete conforming to IS 2312 & IS 302 or latest and other relevant IS/IEC standards & as per explanatory note. | — | — | — | 12,600 | |
| — | 21.00 | — | — | ||
| Supply, fixing, testing and commissioning of 600mm sweep, 1200 RPM, industrial weather proof air circulator fan complete conforming to latest relevant IS & as per explanatory note. | — | — | — | 1,45,940.97 | |
| — | 10.00 | — | — | ||
| Supply, fixing, testing and commissioning of 380mm sweep, 1400 rpm (approx) propeller type exhaust fan complete as per IS, IE rule & site requirement & as per explanatory note. Make Bajaj, Usha, Havells, Orient or equivalent | — | — | — | 31,490 | |
| — | 200.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaire, having system wattage 2x18 watt. LED tube and inbuilt LED driver, CRCA body powder coated, complete with all mounting arrangement, accessories. The LED based 4 ft. tube light (lamp) shall be confirming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 2,17,600 | |
| — | 40.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaries 595x595 mm size, recessed mounting fitting (Tile type), as per IS : 10322 having system wattage less than or equal to 48 Watt, CRCA body powder coated, high efficiency milky white PMMA diffuser with no bright spot visible, complete with all mounting arrangement with suitable frame to avoid droping down of fitting of make Phillips, Bajaj, Havells or similar conforming to CEE/NR's spec. No. CEE/NR/121 Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 1,32,160 | |
| — | 10.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4-feet long surface mounting 36-Watt, 5700K,CRI>80, LED Luminaire as per CEE/NR's spec. No. CEE/NR/121 Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121 Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest, IS, IE rules and site requirement. Fitting shall be environmentally friendly, long life, corrosion resistant, impact proof IP 66 with PC housing & opal finish cover suitable for wet location similar to Make - Havells Model No. MAGNUM NEO or equivalent. Fitting shall be suitable for operation on single phase 240Volt, 50 Hz AC supply & as per explanatory note. | — | — | — | 31,000 | |
| — | 50.00 | — | — | ||
| Supply, Fixing, Testing & commissioning of 45-50W LED based street light luminary with cool white light, pressure die cast aluminum housing, IP 65 or latest complete conforming to CEE/NR's spec. No. CEE/NR/121 Elect/PS/2018 (Rev '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121 Elect/PS/2019 (Rev '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 1,48,250 | |
| — | 30.00 | — | — | ||
| Supply of 150 watt LED based flood light luminary with cool white light, pressure die cast aluminum housing, IP 65 or better having system complete conforming to CEE/NR's spec. No. CEE/NR/121 Elect/PS/2018 (Rev '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121 Elect/PS/2019 (Rev '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 2,11,500 | |
| — | 25.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED based highbay luminary with IP 65 having system wattage less than or equal to 150 Watt complete conforming to CEE/NR's spec. No. CEE/NR/121 Elect/PS/2018 (Rev '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 2,32,250 | |
| — | 1500.00 | — | — | ||
| Supply, fixing, testing and commissioning of 2Cx2.5 sq.mm. copper armoured cable as per latest IS, IE rules & as per explanatory note. | — | — | — | 1,72,500 | |
| — | 5.00 | — | — | ||
| Supply, fixing, testing and commissioning of LT distribution board Surface mounting/recessed mounting double door type made up of CRCA sheet sheet with anti corrosion treatment and suitable, IP 54 phosphatised powder painted complete with neutral link, earth point, Din rail and prewired confirming to IEC 61439 of make ABB, Havells, Siemens, L&T, Schneider, Legrand, C&S or equivalent with following items of matching make to be fixed in distribution board, confirming to IEC 60947, IE rules and site requirement. It should be rodent entry proof. It should also include well dressing and coding of circuit & as per explanatory note. 40A 2P RCBO 30/100 mA= 01 No. (Incoming) 6-32A MCB SP "C" Series =9 Nos. (Outgoing) | — | — | — | 32,795 | |
| — | 5.00 | — | — | ||
| Supply, fixing, testing and commissioning of LT distribution board Surface mounting/recessed mounting double door type made up of CRCA sheet sheet with anti corrosion treatment and suitable, IP 54 phosphatised powder painted complete with neutral link, earth point, Din rail and prewired confirming to IEC 61439 of make ABB, Havells, Siemens, L&T, Schneider, Legrand, C&S or equivalent with following items of matching make to be fixed in distribution board, confirming to IEC 60947, IE rules and site requirement. It should be rodent entry proof. It should also include well dressing and coding of circuit & as per explanatory note. 63A 2P RCBO 30/100 mA= 01 No. (Incoming) 6-32A MCB SP "C" Series =18 Nos. (Outgoing) | — | — | — | 66,035 | |
| — | 1.00 | — | — | ||
| Supply, fixing, testing and commissioning of LT distribution board Surface mounting/recessed mounting double door type made up of CRCA sheet sheet with anti corrosion treatment and suitable, IP 54 phosphatised powder painted complete with neutral link, earth point, Din rail and prewired confirming to IEC 61439 of make ABB, Havells, Siemens, L&T, Schneider, Legrand, C&S or equivalent with following items of matching make to be fixed in distribution board, confirming to IEC 60947, IE rules and site requirement. It should be rodent entry proof. It should also include well dressing and coding of circuit & as per explanatory note. TPN MCB 63A 10KA 'C' series= 01 No. (Incoming) SP MCB 6-32A 10KA 'C' series=18 Nos. (Outgoing) | — | — | — | 5,691 | |
| — | 2.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning of front operated double door type weather proof feeder pillar body made of CRCA sheet sheet with anti corrosion treatment and suitable having IP 65 protection (MCCB - Incoming & MCCB - Outgoing) comprising with the following MCCB's fixed in it of make: Havells, Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC 60947-2 / IS 13947: 2008 & IS 8623:2008 or latest with digital measuring instrument & bus-bar arrangement confirming to PCEE/NR's spec. No. PCEE/NR/126-Elect/PS/2019 at Tech Spec-III attached or latest and as per IS, IE rules and site requirement. It should be dust and vermin proof, conforming to IS 8623:2008 and powder coating as per IS 13871-1993 (or latest version) & should be as per explanatory note. 4P MCCB 250Amps 36 kA with adjustable thermal & fixed magnetic release = 01 No. (Incoming) 4P MCCB 125Amps 36 kA with adjustable thermal & fixed magnetic release = 02 No. (outgoing) 4P MCCB 63Amps 36 kA with adjustable thermal & fixed magnetic release = 04 No. (outgoing) | — | — | — | 2,15,818 | |
| — | 200.00 | — | — | ||
| Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required & as per explanatory note. 150 mm width X 50 mm depth X 1.6 mm thickness | — | — | — | 1,48,400 | |
| — | 300.00 | — | — | ||
| Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required & as per explanatory note. 300 mm width X 50 mm depth X 1.6 mm thickness | — | — | — | 2,66,499 | |
| — | 1200.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 35 cm and depth-(75-100) cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Upto 35 sq. mm | — | — | — | 4,53,900 | |
| — | 200.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 35 cm and depth-(75-100) cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Above 35 sq. mm and upto 95 sq. mm | — | — | — | 84,200 | |
| — | 200.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 35 cm and depth-(75-100) cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 93,400 | |
| — | 100.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 55 cm and depth-(75-100) cm maintaining gap not less than 20 cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Upto 35 sq. mm | — | — | — | 29,300 | |
| — | 100.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 55 cm and depth-(75-100) cm maintaining gap not less than 20 cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Above 35 sq. mm and upto 95 sq. mm | — | — | — | 31,100 | |
| — | 100.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench [size width- not less than 55 cm and depth-(75-100) cm maintaining gap not less than 20 cm] etc as required as per detail drawing approved by competent authority & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 33,100 | |
| — | 600.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface/cable tray as required & as per explanatory note. Upto 35 sq. mm (clamped with 1mm thick saddle) | — | — | — | 33,498 | |
| — | 200.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface/cable tray as required & as per explanatory note. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) | — | — | — | 28,200 | |
| — | 200.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface/cable tray as required & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) | — | — | — | 33,200 | |
| — | 13.00 | — | — | ||
| Earthing with 40 mm dia GI pipe class 'B' 4.5 meter long earth electrode as per IS:3043 (latest version) to achieve earth resistance less than 5 ohms including construction of masonry enclosures with hinged cover plate of cast iron with locking arrangement (approx. size 400 mmx 400 mm) on top, provision of earth plate, connections from earth electrode to switch gear/pole as per drawing & as per explanatory note. | — | — | — | 78,074.88 | |
| — | 65.00 | — | — | ||
| Supplying and laying 25 mm X 5 mm G.I strip confirming to relevant IS as per IS:3043/1987 (Latest version), fixing on surface or as per site condition, clamping or fixing with suitable arrangement as per site requirement, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required & as per explanatory note. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) | — | — | — | 9,360 | |
| — | 100.00 | — | — | ||
| Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required & as per explanatory note. | — | — | — | 5,500 | |
| — | 110.00 | — | — | ||
| Supply, fixing, testing and commissioning of 48V, 50 Hz LED based pit light luminary with IP-67 protection, impact resistance IK10 having system wattage 22 watt complete with anti theft mounting arrangement made out of 2 mm thick CRCA sheet with anti corrosive treatment and suitable mounting as per site requirement of make Phillips, Bajaj, Havells or similar conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 4,30,100 | |
| — | 4.00 | — | — | ||
| Supply, fixing, testing & commissioning of Step down single phase transformer 230V/110V or 48 V AC of 5 KVA capacity, double wound winding, input, output voltage meter, Voltage regulation 95% or above, Aluminum/ copper connector suitable for connection with 16/25/35 sq.mm aluminum cable, MCB complete with fixing arrangement, made out of 2 mm thick CRCA sheet with anti corrosive treatment, weather proof enclosure IP 65, indication lamp, foundation arrangement and anti theft arrangement as per site requirement & as per explanatory note. | — | — | — | 58,720 | |
| — | 110.00 | — | — | ||
| Supply, fixing, testing & commissioning of Thermoplastic PC-GFS Polycarbonate weatherproof junction box IP-67 (size 205 x 255 x112 MM) weather proof UV resistant, rain waterproof, temperature resistant, flame retardant suitable for termination of 4C X 16/25/35 SQMM cable with earth terminal as well as loop-in / loop-out of cable. The junction box shall fulfill the following standards. IEC 6067-22:Particular requirements for connecting boxes and enclosures. IEC 60695-2-11 : Flame - retardant & Self-extinguishing. Glow Wire tested at minimum 960 degree C. IEC 60529:IP 66 / IP 67 / IP 69 degree protection as per site requirement & as per explanatory note. | — | — | — | 4,51,990 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of 150 liter/Hrs water cooler Storage type self contained drinking water cooler, operation on 230V AC 50 Hz ( Non CFC refrigerant ), cooling cap(in L/hr)-150, storage Cap (in Lts) 150 ,Max Energy Consumption -1550W, Power Factor = or more than 0.85, Tank sheet material-Strainless steel(Grade A-IS304),Thickness of sheet (in mm) 0.8 equal to or more than, Water Tank cover material -Strainless steel(Grade A-IS304) thickness 0.8 and lid bottom sheet material and thickness-Alluminium sheet material & thickness-Aluminium sheet 1.5 (in mm ),operating voltage 230 V ac single phase 50Hz, Confirming to IS -1475 or latest, ISI marked, warranty on site as per IRS terms & conditions or OEM whichever is maximum, warranty on compressor as per IRS terms & Condition or OEM whichever is higher ,Make :-Sidwal, Bluestar or equivalent & as per explanatory note. | — | — | — | 98,500 | |
| — | 250.00 | — | — | ||
| Design, manufacture, display of wall / hanging / floor mounting type LED illuminated sign / direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed /router cut on monomeric calendered vinyl of 70 mm thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W / sq. ftand with brightness more than ambient light. Suitable size endcap of 1.5 mm thick SS 304 should be provided as per Railway Board letter no.2023/SD-II/22/07/02 dated 15.05.2023 & as per explanatory note. | — | — | — | 6,07,000 | |
| — | 250.00 | — | — | ||
| Errection and installation of wall / hanging / floor mounting type LED illuminated sign /direction boards in half elliptical shape. The display sheet shall be of unbreakable040 translucent polycarbonate sheet of 2 mm thickness. The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed /router cut on monomeric calendered vinyl of 70 mm thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W / sq. ft and with brightness more than ambient light & as per explanatory note. | — | — | — | 60,750 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .