Special repair to bldg No. P-246 (Maj accn), provision of septic tank and soakage well near bldg No. T-221 (East wing mess), T-131 ( C coy) and P-185 and provision of street light from sub station No.2 to road leading to shopping complex at CME Pune

Amount

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed

All as per item No.1 above, but bedded in lime or cement mortar complete all, as specified and directed.

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

S&F Framed work such as roof trusses (framed), trusses purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed.

S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed.

M & L for Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide primer complete all as specified and directed

M & L for Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed.

M & L for Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm, cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction including taking down old ceiling Make of GI Grid work : Armstrong/Swastik/Techno Grid Make of 'E' board : Everest/Indian Gypsum/Armstrong or equivalent approved .

Dismantling water tanks and removing to store capacity exc. 500 & not exc. 1000 litres complete all as specified and directed.

S&F For 1000 litres capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed.

M&L for 40 mm thick, PCC 1:2:4 (Type B1 using 20 mm graded aggregate) as in levelling course to match the undulations of roof and in in coping, roof kerbs, fins and in sunken floor including benching etc complete all as specified and directed

M&L 10 mm thick cement screed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab and vertical surface ,finished even and smooth by using steel trowel complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by forced complete all as specified and directed. Four course roof treatment consists of as under :- (a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm. (b) Laying of APP based membrane as specified thickness and weight. (c) Applying one coat of bitumin grade 85/25 @ 1.2 Kg/Sqm. (d) Applying two coat of aluminium paint @ 100ml/sqm

Supply only liquid water proofing compound as per manufacturers instructions.

M&L for Cement concrete tiles 25 cm x 25 cm x 22 mm thick, machine pressed set jointed and pointed in neat cement slurry in floors, cut and polished and laid over 10mm thick CM 1:3 etc. complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or aboved ground level) complete all as specified and directed

M&L for 75mm thick PCC type D-2 (1:4:8) using 40mm graded aggregate as in sub base complete all as specified and directed

M&L For 25 mm thick, type B-1, 1:2:4 (20mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6. complete all as specified and as directed.

M&L For double charged light shade vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed

M & L Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed

M&L for double charged light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed

M& L for rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

M&L for glazed ceramic coloured tiles in verticle surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No .31 above, but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement to match complete over and including 10mm thick cement screed in CM 1:4 complete all as specified and directed.

M& L For 20 mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Labour only for rounding to edges of stone slabs, such as in steps, cooking plateform, and other similar situation complete all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit complete all as specified and directed

All as per item No.36 above, herein before but 20mm bore

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed

All as per item No. 40 above, herein before but 20mm bore.

M& L For Cutting chases, pinning in stone concrete black or slab , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth etc. complete all as specified and directed

S&F in repair under counter wash basin vitreous China coloured including CI bracket, 15 mm dia. Polythene connection, 32mm dia chromium plated (CP) waste coupling, chain and plug waste fitting union and 32mm dia PVC waste pipe 90cm long and all necessary inlet outlet connections etc. complete all as specified and directed. Make : Hindware cat No. 10065 or equivalent approved make indicated in list of makes in tender.

M & L for coupled closet (Clover) snow white, size 360x640x685mm, make Jaquar including P or S trap along with cistern dual flush complete set with soft close plastic seat cover complete as specified and directed including taking down old wash down water closet pan of any description any size. Make : Jaquar, code SLS-WHT-6851P180PP or equivalent approved make by GE-B/BA/WC/JAQ/C/0006, Make : Jaquar and bottle trap. Make : Jaquar code 164071N-CP, or equivalent approved make as indicated in list of make of tender including taking down old u/s one complete all as specified and directed.

S&F For in repair brass chromimum plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specified and directed

S & F in repair for brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc.complete all as specified and directed

S&F in repair 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type long body , screwed down high pressure, with or without lettered 'Hot' or 'Cold' woth long shanks and flynuts, screwed for iron pipe complete all as specified and directed

S&F PVC in repair connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F in repair 15mm fancy type bib tap, long body chromium plated with crutch or butterfly handle, long body screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

S & F in repair overhead shower 100 mm dia round shape single flow (ABS Body Chrome plated with grey face plate ) with Rubit cleaning system complete fixed to ceiling all as specified and directed by Engineer-in Charge. Make - Jaquar Cat No. OHS-1989 or equivalent approved make indicated in list of makes in tender as approved by GE.

M&L cement concrete type E-2, 1:5:10 (40 mm graded stone aggregate) lean concrete as in sunkun floor for filling etc. complete all as specified and directed.

M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Supply only WPC all as per manufaturers instructions.

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L Polythene film black 50 micron laid in floor complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No.57 above, but 110mm complete all as specified and directed

S&F in repair 75 mm PVC (SWR) bend any radius complete all as specified and directed

All as per item No.59 above, but 110mm dia complete all as specified and directed.

S&F in repair 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

All as per item No. 61 above, but 110mm bore of pipe complete all as specified and directed.

M&L in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item No.63 above, but 110mm complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

All as per item No.65 above, but 110mm complete all as specified and directed.

S&F in repair stainless steel sink , made out of 1.00 mm thick sheet for kitched with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x 330mm x160mm all as specified and directed. Make: Nirali/Diamond/Blue King/Kingston/

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

M&L for stainless steel 304 material staircase railing of ht 1.00 m with Top rail pipe 50mm bore (16 gauge), vertical pipe 40mm bore (16 gauge) @ not exc. 1.00 m c/c and at turning and corners with 10 mm thick toughened glass of height 0.75 m and necessary fitting for fixing of glass, including Tee, cross, bend, base coupling, fixed in floors with necessary fastner complete glossy finish complete all as specified and directed.

S&F For in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steel bracket guard and railing 60 cm long etc. complete all as specified and directed

S& F in repair stainless steel Soap dish holder complete as specified and directed by Engr-in-Charge. (Make : Jaquar or equivalent)

S & F in repair Toilet paper roll holder with flap complete as specified and directed by Engr-in-charge. Make : Jaquar or equivalent.

S& F in repair Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

Taking down chowkats or frames with shutter(without taking off shutters from the frames) not exc 1.5 sqm each and removing from sitecomplete all as sepcified and directed.

All as per item No.75 above, but exc. 1.5 sqm and not exc. 4 sqm complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred,put together with glue pinned at joints etc. complete all as specified and directed

S&F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed .

S&F factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and directed

M&L for preparing new surface of wood of any decription , not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

S & F for Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified and directed

M & L for preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc. 0.1 Sqm each complete all as specified and directed

M & L for Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as spd.

S & F powder coated Aluminium sliding windows three track with two glass shutters using 5 mm thick glass tinted Modi guard and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, Aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete. Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

S & F for Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not therwise provided for

M&L for framed work such as grills or grating etc with ends of bars shouldered as framed guard bars conforming to Fe-410-0 or 310-0 all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube etc all as specified and as directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed

M&L 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw.complete all as specified and directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed

M&L 200 mm aluminium anodised, barrel tower bolts of extruded section and fixe

M&L 150 mm aluminium anodised, barrel tower bolts of extruded section and fixe

S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised , sliding door bolt with hasp, staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Demolition of brick or stone/boulder masonry, built in cement mortar including all quoins, aarches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Racking out joints/pointing to random rubble masonry, polygonal rubble uncoursed or brought upto course complete all as specified and directed.

M&L keyed pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto complete all as specified and directed

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonary surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat primer on walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and directed.

M&L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coats of Oil Bond distermper white or tinned over an coat of primer on walls, etc complete all as specified and directed

All as per item No.112 above, but two coats of cement base paint without wall care puttycomplete all as specified and directed.

All as per item No.112 above, but two coats of white wash on ceiling complete all as sepcified and directed.

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decorative type curtain rods with and including derocitve type brackets for fixing curtain rod complete all as specified and directed

M&L cement concrete 1:3:6 type C-2 (40mm graded stone aggregate) as in floors plinth protection, path etc 75mm thick smooth finished surface without using extra cement complete all as specified and directed

Chipping off loose concrete/plaster upto sound stratum of RCC members such as slab, chajjas, columns, beams and clean surface with wire brush, washing down with water usiing water jet including necessary scaffolding & propping to support the structural members where work is to be executed and removing debries to a distance exc. 250 metre but not exc. 500 metre.

M & F for providing and applying rust inhibition coat system (in two coats) as per manufacturer's instructions to exposed reinforcement after cleaning and removing scales and rust complete all as specified and directed by Engineer-in-Charge.

M & F for providing and applying a bond coat (epoxy based bonding materials) to all exposed concrete surfaces all as sper the manufacturer's instructions as specified and directed by Engineer-in-Charge.

M & F for providing and appying latex polymer modified cement mortar in specified composition of system [ i.e. cement 400 parts by weight quartz sand 1600 parts by weight, polymer 60 parts by weight, water 120 parts by weight] to RCC surfaces all as sper the manufacturer's instructions and directed by Engineer-in-Charge. (Note:- Thickness of plaster /filling varies from 15 mm to 25 mm)

M&L treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors

Supply and fixing in repair stainless steel kitchen cup/ saucer/ kitchen utensils, holder basket, corrosion resistance, seamless glosy finish, nicket chromium plated using 5mm dia. Wire/ SS perforated sheet assembled and fabricated as required size and finish,including telescopic drawer channel of stainless steel zinc finish ( silver colour ) of weight capacity minimum 35 kgs including necessary fixing arrangements hinges and ss screws, with solid handle of stainless steel chromium plated of 200 mm 'D' shape including necessary fixing arrangements hinges and screws, ball catches with 8mm dia. steel ball and brass body and striking plate including letting in and necessary fixing arrangements hinges and ss screws and veneered decorative plywood grade 1 ( with BWR resin ) with decorative face veneers on one side as in drawers/ cupboards moulded as required including necessary fixing arrangements etc. complete all as specified and directed by Engr. - in - charge.

M&L for girt cushioning below interlocking paver block incl spreading and levelling complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block reflective type coloured any shape and size confirming to IS 15658-2006 of M-35 grade , with grey cement and pigment complete all as specified and directed.

M& L for filleting in any position and to any shape in cement cement mortar 1:4 including all mitres, stops, including sectional area n. exc. 25 Sqcm etc complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. credit for above items should be made as per conditions separately.

Taking down ceiling fans any type/sweep 230 V AC and depositing to AGE E/M store complete all as specified and directed.

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface type with PVC modular white cover plate for mounting fittings such as switches, sockets, fan regulators etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc

All as per item No.128 above, but for one multipin 5 amps socket outlet on same board.with other switch complee all as specifed and directed.

All as per item No.128 above, but for one multipin 5 amps socket outlet on independent board with other switch complee all as specifed and directed.

All as per item No.128 above, but for one light point controlled by 2, 2 way switch complete all as specifed and directed.

All as per item No.128 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board complee all as specifed and directed.

S & F ceiling rose, 3 phase PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complee all as specifed and directed.

S & F lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complee all as specifed and directed.

S & F in replacement call bell ding dong AC, 230 Volts, single pole complee all as specifed and directed.

S&F switch Modular, one way 6 Amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F switch Modular, two way 6 Amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F switch modular one way 16 Amps, 1 module with suitable plate and cover complete as per existing make and model all as specificed and directed

S&F socket modular 6A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

S&F socket modular 6A/16A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

S&F modular bell push 6 Amps 1 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 No PVC square blocks incl taking down old UNSV fitting. Make :- Havells Cat No. LUMILINEBS20WLED830SPCWH or equivalent of Philips/ Bajaj/ Crompton/ Wipro/ Shakti/ Halonix/ Jaquar/ Benlec India Ltd.

S&F surface and wall mounted LED batten (LED tube light fitting 10W), extruded aluminium housing provided for efficeient heat dissipation with polycarbonate diffuser & integrated electronic driver alongwith LED tube 10 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting. Make :- Havells Cat No. LUMILINETBS10WLED865SPCSS or equivalent of Philips/ Bajaj/ Crompton/ Wipro/ Shakti/ Halonix/ Jaquar/ Benlec India Ltd.

S&F Endura Gugby Neon IP-65 environmental friendly, ultra modern energy saving surfae mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 10 Watt incl taking down old UNSV fitting. Make :- Havells Cat No. RUGBYGENXFTS10WLED865SSYMBOPC or equivalent of Philips/ Bajaj/ Crompton/ Wipro/ Shakti/ Halonix/ Jaquar/ Benlec India Ltd.

S&F building security LED light fitting 25 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 incl taking down old UNSV one. Make :- Havells Cat No. ENDURASUNDOWNSL25WLED765PASYBOPCIHO or equivalent of Philips/ Bajaj/ Crompton/ Wipro/ Shakti/ Halonix/ Jaquar/ Benlec India Ltd.

S&F decorative wall light fittings (bracket light), CITY 3 made up of polycarbonate suitable for 10 watt LED lamp incl LED lamp incl taking down old UNSV one. Make :- Havells Cat No. LHDL06160099 or equivalent of Philips/ Bajaj/ Crompton/ Wipro/ Shakti/ Halonix/ Jaquar/ Benlec India Ltd.

M&L for sub main wiring with two run of 6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC casing caping of desired colour not less than1.2 mm thick and 25 mm wide & 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one.

All as per item No.148 above, but size 4 Sqmm two runs and with one run 4.0 sqmm FRLSH copper wire for earth continuity.

S&F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

S&F in replacement MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one.

S&F in replacement MCB distribution board double door 240 volts 4 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

S & F in replacement MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one.

S & F in replacement MCB SPN 40 Amps, 230 V, AC incl taking down old unserviceable one.

S & F in replacement MCB SPN 20 Amps, 230 V, AC incl taking down old unserviceable one.

M & L for earthing complete with GI earth plate electrode of size 60 x 60 x 0.6 cms thick burried directly in ground vertically at a depth of not less than 2.25 Mtrs below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanised iton strip of 25 x 4 mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, 40 mm dia GI tubing light grade protection pipe upto test point, 20 mm dia GI watering pipe with funnel and wire mesh, PCC pit 1:3:6 with pit cover of size 30x30 CM made of RCC 1:3:6 with suitable handle, angle iron frame of angle iron size 40 x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling in all as required at site all as specified in plate No 3 of SSR Part-I and directed by Engr-in-Charge.

M&L in replacement of LED lamp 9 watt complee all as specifed and directed.

Supply and fix electric water heater vertical/horizontal type, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for laying cables and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for pole foundation/laying cables and getting out in Hard/dense soil all as specified and directed.

Excavation in trenches exceeding 1.5m wide and not exc. 3m in depth for pole foundation/laying cables and getting out in Hard/dense soil all as specified and directed.

Excavation over areas 1.50m in depth for foundation etc or for shaft, wells, cesspits, manholes , pier holes etc not exc. 10 Sqm on plan and not exc. 1.50 m in depth and getting out in soft/loose soil all as specified and directed.

Excavation over areas for depth beyond 1.50 mtr and not exc. 3m and getting out in hard/ dense soil all as specified and directed.

Returning filling in, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm all as specified and directed.

Removing surplus excavated material (soil) to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, eletric power cables (heavy duty) with stranded aluminium conductor 1100 Volts grade cross sectional area 4 core 16 sqmm all as specified and directed.

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl coupler & bends complete all as specified and directed.

S & F LED street light fittings of 90 Watt system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, TOP opening separate driver compartment with frame, IP 66 protection suitable for pole mounting SMD led array with lense, cool white 6500 K, LED efficacy > 120 Im/W and system efficacy 90 Im/W, 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, power factor >0.95, working temperature range -20 to 60 degree celcius, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole incl make proper connection complete including cutting, welding, drilling holes, nut bolts, washer complete all as specified and directed by Engineer-in-charge.

Supply & fixing or passing through pipe, 1100 volts grade heavy duty, PVC insulated round 3 core 2.5 sqmm copper cable including electrical connection complete all as specified and directed.

S & F street light bracket made out of GI pipe medium grade 32 mm bore approx length not less than 120 cm bent to shape including new clamps made of MS flat of size 40 x 5 mm thick including cutting, welding, drilling holes, nut, bolts washers etc including two coat of aluminium paint over one coat of red oxide primer on MS work complete all as specified and directed.

S & Kiosk box made out of fibre material complete with TPN, aluminium bus and suitable for one number MCB (SP) including one No. MCB (SP) 6 Amps 240 volts with glands for incoming & outgoing cable including fixing of flat iron clamps of size 20 x 4 mm on PCC/Steel tubular pole complete all as specified and directed.

Material & labour for earthing complete with galvanized steel earth electrode plate of size 60x60x6 mm thick buried directly in ground/earth pit not less than 2.25 mtr deep below normal ground level and top edge of earth electrode not less than 1.5 mtr below normal ground level and connected with GI earth wire of size 4 mm by means of nut, bolts, washers etc. to eqpt/ machinery all as shown in electric plate No. 3 of SSR Part 1 including PCC (1:3:6) pit, pit cover 50mm thick RCC 1:2:4 type B1 using 8mm tor steel bars @ 10cm C/C both ways, 20 mm bore medium grade GI protection pipe, watering pipe 20 mm bore medium grade, funnel, wire mesh also including earth work, common salt, charcoal dust complete all as specified and directed by Engineer-in-charge. (Note : Earth wire/strip to be secured on bus bar insulators and insulators shall be fixed on pole not more than one meter apart with MS clamps made out of 25x4mm MS flat with nuts, bolts and washers and GI wire/strip shall be fixed in such a way that wire/ strip should not be pole in any case)

M & L for GI pipe Light grade with all connected accessories of sizes 40 mm complete as specified and directed. Note :- Clamps, nut, bolts, saddle etc will be paid & measured seperately.

M & L for steel swaged poles complete with cast iron base plate, finial taperplug, bolts, nuts and screws as specified type 410 SP-31 and including painting with two coats of synthetic enamel aluminium paint over a coat of primer including preparation of new surfaces all as specified and directed.

M & L for providing plain cement concrete type D2, 1:4:8 (using 40mm graded aggregate) in foundation filling and mass concrete all as specified and directed.

M & L for providing plain cement concrete type C2, 1:3:6 (using 40mm graded aggregate) as in coping, finished even and fair, including necessary from work concrete all as directed at site

M & L for PCC 1:2:4 type D-2 using 40 mm graded stone aggregate as in / floor finish for 150mm thick

M & L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete

M & L for Brick work with sub class 'B ' bricks straight or covered on plan exc. 6m mean radius built in cm 1:4.

M & L for Brick work with fly ash bricks straight or covered on plan exc. 6m mean radius built in cm 1:4.

Loose filling with broken bricks,aggregates of gauge 80 to 150 mm in sokage well

M & L for RCCM 20 using 20mm graded stone aggregate as in Walls, retaining walls, basement walls, ballasts wall and the like ; any thickness above top of footing including attached pilasters and buttresses .

M & L for RCC M 20 using 20mm graded stone aggregate as in slab supported on walls, beams and columns in floor, roof landing, balconies, canopies, dech slab and in shelves and the like

Use & Waste of form works to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work, rough finished surfaces not exceeding 200mm thick

Use & Waste of form works to edges of concrete flats, treads, breaks in floor, window cill, concrete, opening in concrete walls floor and roof not exc. 20cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc. 5 cm but not exc. 10 cm wide for rough finished concrete surface all as specified and directed.

M & L mild steel TMT bars 6-8mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less that 0.9 mm dia or securing with clips all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregates ) as in bands all as specified and directed.

M & L rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth w/o using extra cement mixed with water proofing compound as per manufacturer's instructions all as specified and directed.

Supply only integral water proofing compound @ 2.5% by weight of cement

S & F cast iron soil, waste and vent pipes, in any length with or without ears with cement joints fixed to walls 75 mm dia bore sand cast pipes all as specified and directed.

M&L salt glazed stone ware drain pipes 150 mm dia laid in trenches and jointed all as specified and directed.

M & L PCC 1:4:8, type D2 as in concrete bed to drain pipes including forming cradles for 150 mm dia. of RCC pipe etc. including packing under and haunching against the sides of pipes after they are laid complete all as specified and directed.

M & L 150 mm dia.of reinforced concrete pipes, class NP3, laid and jointed complete with collars all as specified and directed.

M & L plain cement concrete 1:3:6, type C2 using 40mm graded stone aggregate as in surface channels and drains etc. complete all as specified and directed.

M & L For rendering 10mm thick on fair faces of brick work or concrete surfaces and making smooth and even surfaces without using extra cement in cement mortar 1:3 etc. complete all as specified and directed.

Providing precast reinforced cement concrete 1:3:6, type C-1, ( using 20mm graded aggregate) set in CM 1:6, as in man hole cover etc. complete all as specified and directed. Note :- Reinforcement required shall be measured and paid separately under relevant item.

Cutting hole in stone/block wall built in cement mortar of superficial area exc. 150 sq. cm but not exc. 400 sq. cm etc complete all as specified and directed.

S & F in repair viterous china wash down water closet pan (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap provision of flush pipe, plastic seat cover for pedestal pan complete all as specified and directed.

Supply & fixing in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including bracket and 32 mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

Mukund Engineers and Contractors

N AND G CONSTRUCTION

Aishwarya Constructions