Construction of Muthalvar Padaipagam as additional building in the existing knowledge centre at Thamukkam Main road in ward 31 Zone II in Madurai Corporation

Amount

DISMANTLING WORKS Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls Dismantling Pressed Tiles & Weathering Course W-0037 (PWD SOR 2024-2025, P,No 22, SI.No 28)

Brick / Stone Masonry in cement mortar walls under 3m high (PWD SOR 2024-2025, P,No 21, SI.No 27)

Dismantling RCC by manual / by using deploying machineries

CIVIL WORKS Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation and basement with filling M sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. UP TO 3.20M LEVEL

UP TO 5.20M LEVEL

UP TO 11.20M LEVEL

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.UP TO 5.20M LEVEL

UP TO 11.20M LEVEL

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials) For Ground floor

For First floor

For Second floor

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages, laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification. For Ground floor

For first floor

For Second floor

For Head room floor

Brick partition walls of 11.50cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7 cm in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Crushed stone sand ), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc. complete complying with standard specification and as directed. -100sq.m S.I.333

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Providing two legged scaffolding using suitable sizes of casurina posts of 1.50cm overall length 3m height+0.50lap) The distance between the two rows being 2 m and the spacing of posts being 2m in both rows with two horizontal posts with 0.50m. overlap on either side and bracesat 2mC/C including longitudinal and transwere middle of 40mm thick and 1m width etc .incomplete shape using coirand nail sand as directed by the Departmental Officers.

Supplying and fixing Shade Net (Green Net) for under construction of high rise building etc Complete

Painting old wall surface with Two coat of Plastic Emulsion paint of approved quality including cleaning of plaster surface with soap soda and water by manual labour.etc Complete

Painting two coats with Ready Mixed Enamel Paint over the Old iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Painting two coats with Ready Mixed Enamel Paint over the Old wood works of approved quality and colour without Synthetic Enamal paint of approved quality including the cost all materials etc.,complete, in all floors.

Supplying and Fixing of Aluminium Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes Emblem (15”)

Tamil Brass Letters - 25cm

English Brass Letters - 25cm

Aluminium Dye Cast Letters 9’’ size

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete (PWD SOR P.NO : 61)

Supply of Fixing of SBR water proofing sheet 3 to 4mm With Geo Textiles 2 layer etc Complete

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

JOINERIES ARRANGEMENTS Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor spring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality. The vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers M-0713 VOL-1 P.NO: 117

UPVC Window Specification: Supplying and fixing UPVC (Un- Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work (pwd sor p.no 70)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un- Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work (pwd sor p.no 71)

FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers M-0394

Supplying and fixing in position of Alu.Anodised Partition with 62 x 38 x 2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips. rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill titheextent required and made good to the original condition safter fixing as directed by the departmental officers.All the Aluminium sections should beanodised to 1.5 microns as per ISI

Supplying, fabricating and fixing inposition of Alumi. Anod.natural colour matt finish door half glazed and half PLB board using 12mm thick PLB board and 5.5mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with neessary accessories such as rubber beading, Al.Clips, Best double action floor springs, Aluminium Handle son both sides, floor stopper, Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi.surface must be anodised with matt finish under electrically controlled condition inaccordance with IS specification 1868/1962 of Anodicfil thickness of not less than 15 Microns (Fifteen) for all sections.

WATER SUPPLY AND SANITARY ARRANGEMENTS Providing & fixing PVC RAIN WATER DOWN FALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes, Bemds, other clamps, screws nails etc., complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm](D)

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. 100mm dia pipe

50mm dia pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. (D) 25mm Gun Metal Valve

32mm Gun Metal Valve

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary (D) SD Tap

Pillar Tap

Internal Water Supply Arrangements using UPVC pipes and UPVC specials Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. 25mm dia Pipe

32mm dia Pipe

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed Coupler 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Elbow 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Bend 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

TEE 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

UNION 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

REDUCER 25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Reducer Tee 25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Reducer Elbow 25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Hex Nipple 25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).(D) PVC Elbow 110mm dia

PVC Elbow with Door 110mm dia

PVC Tee 110mm dia

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications (D)

Supplying and fixing in position 15mm dia stop cock of approved make confirming to IS specifications and qulity including cost of Shellac thread etc. complying with standard specification. PWD sor pg.no:48 Stop Cock

Supplying and fixing in position Indian make bewelled edge mirror of size 600 x 450mm quality including cost of Rawal plugs, brass screws. etc. complying with standard specification.(D)

Supplying and fixing in position CP Two Way Bib Cock with Health Faucet complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank.

Supply and delivery of Electric Monoset centrifugal pump conforming to IS9079:2002 asamended from time to time ,with CIFG200 Casing ,hydraulically and dynamically balanced BronzegradeLTB-2 impeller ,impeller ring and casing ring,stainlesss teel shaft capable of discharging required quantity of water against a total head noted below due to all causes.Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at theminimum NPSHA at sit conditions. The shut off head shall beat least 25% over and above the head at duty point.The pump shall be suitable for operation in A Cthreephase,415V+/-10%,50Hz+/-5%. Squirrel cage induction motor for continuous operation.The speed of the Pump and Motor shall be not less than 2700to2900 RPM respectively 5 HP.(200X35) WD- M1568 TWAD SORP.NO : 100

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water- cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact(250lts) (PWD SOR PG NO 118)

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge (Make Jaguar URS- WHT- Page 13253N or Equivalent

Supply and fixing in position white European Water Closet (single piece of wall mounted) of approved make with low level concealed flushing tank 10 litre capacity of best quality and approved make with 100mm Por S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works. (Make Parryware Claret Rimless Single Piece Suite S220 C8640 or Equivalent) White glazed European Water Closet with 10 litre capacity PVC flushing tank fixed on to wall

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings- 100 mm x 75 mm including all charges etc, complete as per standard specification.(D)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three Crushed stone sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.(D)

Providing rain water harvesting using 3 nos.of R0.45 well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with R0.45 circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmneal officers etc., complete in all respects.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification. (CLEAR SIZE 0.90 X 0.90)

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., LevelSwitch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. (250 Litres) (pwd sor pg no 118)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

LANDSCAPE & PLANTATION Supplying and filling of red soil for lawn area for plants including cost and conveyance of all materials to site including labour charge for all complete as per standard specification.

Providing Fym & Vermicompost for the planting including broadcasting etc., complete with all lead and lift and as directed by the engineer- incharge (All labour, materials, tools and plants etc., by contractor)sor :pg;no:268

Supplying and planting of Mexican lawn in & australian dipling method etc., Complete with all laboour, lead and lift and as directed by the engineer-in charge. (All labour, materials, tools and plants etc., by contractor)SOR,PG:NO:299

Planting of Bamboo grass ornamental foliageshrub variety of height 30-45 cm inpolythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavatedearth etc as directed by the site in-charge PD-1633

Planting of Cyprus Plant ornamental foliageshrub variety of height 30-45 cm inpolythene bag of size 6x7 inch includingloading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavatedearth etc as directed by the site in-charge.PD-1643

Planting of Duranta new gold Plantornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size, planting of sapling, refilling of excavatedearth etc as directed by the site in-charge.PD-1650

Planting of Ixora dwarf foliage Specimenplant variety of height 105-120 cm inpolythene bag of size 16x16 inch including loading andunloading charges, transportation, stackingof saplings at site, earth work excavation ofrequired size, planting of sapling, refilling ofexcavated earth etc as directed by the site in charge PD-1739

Planting of Thuja ornamental foliageSpecimen plant variety of height 105-120 cmin polythene bag of size 16x16 inch includingloading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavated earth etc asdirected by the site in-charge. PD-1748

Planting of Bougainvilla foliage shrub varietyof height 30-45 cm in polythene bag of size6x7 inch including loading and unloadingcharges, transportation, stacking of saplingsat site, earth work excavation of requiredsize, planting of sapling, refilling of excavatedearth etc as directed by the site in- charge.

Planting of Ficus black ornamental foliageshrub variety of height 30-45 cm inpolythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavatedearth etc as directed by the site in-charge PD-1656

"Supplying and Planting of Caryota palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge." PD- 1751

Planting of Ficus panda ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge . PD- 1736

SPLIT - AC UNITS SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL 2.0 TR Split Type AC Unit

Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay (V-Gurad / Equivalent) 2.0 TR Split Type AC Unit

Supply and laying of 5/8" and 3/8" copper pipe (Extra beyond 3 metres supplied with AC unit 2.0 TR Split Type AC Unit

Supply and fixing of MS stand for fixing outdoor unit 2.0 TR Split Type AC Unit

INTERNAL ELECTRICAL ARRANGEMENTS CT Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. 1set of 400/5A CT with TNEB Metering provision and 1nos of 400/5A CT for APFCR (Rate As per quoatation)

400A Isolator Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of 400A TPN MCCB panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, (Rate As per quoatation)

Design, supply, fixing, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Incoming 4 No: 63A TPN 25 kA MCCB with Changover Switch Incomers shall have 1 set - Digital Combined meter (Having the parameters of Ammeter,Voltmeter and KWH meter). 1 set - LED type RYB,ON,OFF,TRIP indication lamps. Panel mounted Earth Leakage Relay with Leakage current display. 1 set -100 /5A CT CL 1.0 10VA. Outgoings: 1 Nos - 125 A 36KA TPN MCCB.1 No - 125 A 36KA TPN MCCB 2 Nos - Multifunction Meter digital type / MFM 5010 LED meter CI 0.5S with RS485. Note : All the Outgoing feeder shall be having 'on',off,trip' indication lamps..All switch boards shall be fabricated as per the detailed specification enclosed. Suitable size outgoing cable chamber and extra busbars should be provided for connecting the number of outgoing cables as per the schematic drawing. The board shall be fabricated for future extension of the panel board. Note:-The panel should be having provision to monitor the On, Off, trip status. BUS BAR RATING: 100A TPN 36 KA for 1 sec. Cu.bus bars (Current Density not less than 0.8A/Sq.mm.) with colour coated heat

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB Incomer ) with double door (metal door ) with 1 no. 160 A 4 P MCCB switch as incoming and 2 nos. 63A 3P MCB , 2 nos. 32A 3P MCB as outgoing with suitable cable end box on wall with earth connection only. Higher End

7 segment TPN MCB DB ( with ELCB) Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only. (SD-621)

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End SD-536

CABLE Supply and laying of 3.5 X 185 Sqmm Sqmm PVC / XLPE armoured LTUG cable in the existing cable trench/cable tray

Supply and laying of 3.5 X 35Sqmm Sqmm PVC / XLPE armoured LTUG cable in the existing cable trench /cable tray

Supply and laying of 3.5 X 25Sqmm Sqmm PVC / XLPE armoured LTUG cable in the existing cable trench /cable tray

Supply and Laying of 2 core 10 sq.mm . PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

GLAND Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 2 x 6 sq.mm. PVC LTUG armoured cable with earth connection

TERMINATION Supply and providing cable end termination of 3- 1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 3- 1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 3- 1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 2C X 10 Sqmm PVC LTUG Alu cable with necessary Alu cable sockets by crimping etc, with electrical connection complete.

CABLE TRAY Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height.

Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150mm width and 50mm height.

Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 450mm width and 50mm height.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point ( 6 points / Coil) Higher End Primary point

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point ( 6 points / Coil) Higher End secondary point

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (DL2)

Supply and Fixing of 40W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Havelles )

supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting (DL1)

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of louvers shutter arrangements for 300mm(12")sweep (Heavy duty) AC Exhaust fan complete

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug & heater)

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1- 1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with 1 No 63 Amp 30 MA Four Pole RCD / RCCB (Higher End) with suitable necessary connection with earth connection complete

EXTERNAL ELECTRICAL ARRANGEMENTS Supply, erection, testing, commissioning of 40KVA DG Set With Diesel Engine developing suitable HP at 1500 RPM, 4 Cycle, 12 cylinder, water cooled, turbo charged, complete with standard Accessories confirming to latest emission control latest norms coupled to alternator rated at 200 KVA, 3 phase, 4 wire, 0.8PF (lag), 415V, IP 21 enclosure, class F/H insulation, with AVR, mounted on a channel iron base frame with foot mounting AVM pads, confirming to IS 4722, 1day capacity Litters fuel tank, 2x12V 120 AH battery with leads, AMF panel, Hospital type Silencer, with acoustic enclosure, control panel, inter connecting control cable, cable end termination, including necessary fuel tank system, lubrication system, cooling system, fabrication of exhaust M.S pipe system, supporting frame, structures arrangement, confirming to CPCB norms etc., all inclusive.

EARTHING Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Earthing as per PWD standard with an earth electrode of 2meter Class 'B' GI pipe of dia not less than 32mm complete with necessary masonary work

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8SWG GI wire at the equal interval of 1.5 meter and etc to complete the work

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth

CCTV CAMERA ARRANGEMENTS Supply, Installation, Testing and commissioning of 16channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual- OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output HDMI1 / VGA1 outputs provided HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback.and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to

Supply, Installation, Testing and Commissioning of 42" smart LED TV with following specifications a) Full HD 4K monitor b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and OFC patch of OFC Single mode Media Convertor with configaration charges etc.,

Supply and fixing of outdoor 4X6 PVC box with 102mmX77mmX102mm with all fixing accessories.

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156- 5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of 3nos 6A, 5 pin socket controlled by 3 nos 6A switch, modular type in suitable size Modular plate and enclosed in a 9 Module Manufacturer's Box complete with interconnections and earthing rate should include all the necessary labour charges to complete the work for NVRs and Monitors.

Supply and Laying of 4 x 6 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and laying of armoured, Single mode, Thermoplastic Tape Inner Sheathed, PVC type sheathed 6 core Optical Fibre Cable with unique fiber excess length control method provides the cable with excellent mechanical and environmental properties and Cable - 2 Embedded FRP provides tensile strength & Anti-buckling properties. It is processed with Filling jelly - Thixotropic jelly to prevent Water ingress in loose tube.

Fixing and Termination of Optical Fibre Cable Single Point ( Point to Point ) Splicing and arrangement charges. (Rate as per quotation enclosed)

Supply and fixing of POE 8 port switch with two uplink port, 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 C̊ ~ +75 C̊ ) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of MS Powder coated made of Out Door Wheather Proof Box 2Ft x 2Ft with Air Ventilation.

Supply and fixing of OFC PVC Black Colour Box 1'x 3/4' x 2"

Supply,Erection of 6mtr Length pole with base plate of size 300x300x12mm as per IS-875 with following specification. Pole Outter dia -76.10mm x 3.65mm Thick x 6 meter with foundation Charges.

Supply and Installation for 5KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply and fixing of DP MCB sheet steel enclosure with 1 no 32A DP MCB switch with necessary fixing accessories ( Rate as per quotation ).

FIRE FIGHTING ARRANGEMENTS Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT PWD SOR Page No.144

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the departmental Officers. (Make: Ravel / Equivalent)

First Aid Box complete with all First Aid Medicines

4 Nos of Fire Buckets made out of 40x40x6mm MS Angle

INTERIOR WORKS Supplying and fixing in position of FALSE CEILING ARRANGEMENTS with copper anodised ' T' Section and 'L' angle frame work of grid size 60x60cm with copper T section and 'L' angel of size 25x25x2mm thick and the same is supported @ suitable threaded nuts suspended rods hung from intervals by ceiling at 120cm c/c in both directions and fixing 60x60cmx20mm thick thermocole inthe grid so as to give a seat to false ceiling including painting the 6mm dia MS rod etc.,including painting the 6mm dia MS rod etc.ions. Necessary opening and arrangementsfor fixing electrical fitings should be provided with suitable frame work etc., complete.

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special copper splines using clips provided by Armstrong and approved by the Engineer-in- Charge. Installation: Install copper box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the copper extruded keel for channelled wood works provided by Armstrong over the lowest and second copper

EXTERIOR ELEVATION WORKS Supply, fabrication and installation of conventional cap curtain wall glazing as per elevation and plan drawings. Aluminium Profile Details are JINDAL sections of CURTAIN WALL SECTION/ Article 22713 101.60 mm x 57.0 mm x 2.10 mm with Lip depth of 14.3 mm PRESSURE PLATE SECTION/ Article 22711 53.0 mm x 10.0 mm x 2.0 mm PRESSURE CAP SECTION/ Article 22712 57.0 mm x 18.3mm x 1.3mm Aluminum profiles shall be Electrocoated BLACK and thickness shall be of 15 microns. Stainless Steel screws of 10 x 100mm shall be used for fixing MS Hot Dip Galvanized Brackets to Typical beam level. Providing and fixing of 10mm Clear Toughened Glass of Saint Gobain make. The Glass shall be fixed using EPDM/Neoprene rubbers between pressure plate and curtain wall double lip aluminum extrusion. Dow Corning 789 Weatherproof Silicone will be used wherever necessary.

Providing and fixing of copper Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Procuring and supply of chairs as indicated in the drawings High back chairs

Office chairs

Reading chairs

Computer zone chairs

Children chairs

Training room chairs

supply of Furniture items including Conveyance Charges etc Complete Childrens Learning Table - Wooden Table ( 1.20 x 1.20 = 8.64m2 )

Reading Table - Wooden Table ( 1.80 x 1.20 = 15.12 )

Reception Table (2.43m x 0.63 x 1.12+0.98+0.75/3)

Reading Table - Wooden Table Kids Zone ( 1.23 x 0.77)

Kids Zone ( 1.83 x 0.62 )

Reading Room ( 2.44 x 0.77 )

CCTV Room ( 1.87 x 0.77 )

Locker Room ( 1.23 x 0.77 )

Rolling Chairs Youth Reading Section

News Paper Reading Section

Lockers Room

CCTV Room

Reception

Dinning Table (1.85 X 1.22)

Dinning Table Chair

Childrens Dinning Table Chair

Rolling Chairs

Book Racks (6'6" x 4'0") Youth Reading Section

Store Room

Childrens Area

Stainless Steel Chair (3 Seater)

Stainless Steel Chair (2 Seater)

Add GST 18%

BHAVADHARANI BUILDERS (BID ID -1371013)