COMPREHNSIVE REPAIR TO JOINERY FLOORING PLASTERING SANITARY FITTINGS AND OTHER CONNECTED WORKS AND DAY TO DAY MAINT AT TECH AREA TAKU AND REPAIRS REPLACEMENT OF DAMAGE SEWAGE LINE AND OTHER CONNECTED WORK AT ADMIN AREA CPE ITARSI UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down chowkats or frames with shutters (without taking off shutters from frame) n exc 1.50 sqm each including making good area complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) exc 1.50 Sqm & nxc 4.00 Sqm each including making good area complete all as specified and directed.

Taking down shutters of any description size of shutter exc 1 sqm but n.exc 2 sqm and removing from site complete all as specified and directed.

Taking down and refixing same opening shutter exc.1 sqm and not exc 2 sqm each complete all as specified and directed.

S&F of pressed steel frame for doors with one or more rebates size of frame 125x60 mm including necessary fixing lungs hinges lock strike plate etc including back filling of pressed steel frame with cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F of pressed steel frame for doors with one or more rebates size of frame 105x60 mm including necessary fixing lungs hinges lock strike plate etc complete all as specified and directed.

Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification and drawing complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F of 35 mm thick second class hard wood glazed and skeleton shutters for door, open rebated prepare to receive glass gauge etc (sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered bead’s for securing glass gauge etc size of marker of shutters as per SSR Part-I section-8 clause 8.24 (a) complete all as specified and directed.

S&F of factory made 35 mm thick flush shutters solid core construction with block board core and plywood face panels complete all as specified and directed.

S&F of aluminium anodised powder coated of colour as approved door with frame and shutters partially glazing 5.5mm thick one side reflective glass (tinted glass) and PVC composite board 5mm thick fixed with aluminium clip section (including rubber beading) door section of aluminium door shutter as under complete and all as specified and directed. Note: (i) Frame 100x 45x2mm (ii) Shutter style 85x44.45x2mm thick section (iii) Top rail 95.25x44.45x1.7mm thick (iv) Middle rail 83.50x44.75x1.7mm thick (v) Bottom rail 114.30x44.15x1.7mm thick section (vi) Glazing clip 0.7mm thick (vii) 2 Nos Handle powder coated aluminium 200mm long as approved (viii) Tower bolt 9.90mm dia and 200mm long (ix) Mortice lock 100mm 7 lever make Godreg (x) Hold fast aluminium 100mm long (xi) 1 Nos floor door spring each shutters (xii) Reinforced with 2 Nos 10mm dia MS bar with bolt complete on top and bottom rail of door. Note:- PVC/rubber linning brush for alround door

S&F of 30mm thick glazed and skelton shutters second class hard wood for windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, section 8 clause 8.24(b) prepared to receive glass gauge dividing in squares size of member as per specification complete all as specified and directed.

M&L for box type steel window double frame (glazed and gauged) made of ERW tube P-section of size 60 mmx25 mm double rebated outer frame comprise glazed skelton shutter door frame of ERW tube P-section size 50mm x 20 mm with two nos openable leaf consisting of two nos of sash bar of T-sec 20 mm x 3 mm welded to frame with one no vertcial mullion of ERW of ERW box type T-section size of 60 mm x25 mm FI 2 mm thick welded / screwed to frame for fixing of wire guage/glass including fixture and fitting like as handle, tower bolt stopper, cleat, pintal hinges, holdfast primer etc, complete all as specified and directed. Note- Sheet glass,wire mess,10mm Sqr bar security grill will be measered and paid seaperately and window will be measured one side only.

All as per item No 14.00 here-in-before but single shutter(glazed) with single frame complete all as specified and directed.

S&F of aluminium anodised powder coated sliding type three track window with shutter and frame including aluminium grill and mosquito proofing net and 5 mm thick tinted glass, size of frame 93.00 x 31.75 x 1.3 mm thick for top and sides, 93.00 x 31.75 x 1.3 mm thick, bottom and shutter frame 38 x 18 x 1.5 mm thick, aluminium grill 6 mm dia design No DG-102 make DEDO grill or design No A-103 make aluminium grill fixed to 50 x 20 x 1.5mm thick including necessary handles, tower bolts, stopper etc complete all as specified and directed.

S&F of 250mm long mild steel sliding door bolts plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F of 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F of 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F of 150mm long, aluminium extruded alloy handles, fabricated type, anodised complete all as specified and directed.

S&F of butt hinges 75mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F of aluminium anodized barrel tower bolt of extruded section of size 200mm long complete all as specified and directed.

S&F of 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed.

S&F of 140mm long, floor door stoppers of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floors complete all as specified and directed.

S&F of door closer hydraulically regulated, aluminium body, designation No.2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description not exc 1.00 sqm each complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description exc 1.00 sqm and not exc 2.00 sqm each complete all as specified and directed.

S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinted tacks or galvanised wire staples fixed with wooden beading complete all as specified and directed.

Hacking out old broken glass panes of any thickness description from wooden frame or stone concrete or steel frame or brick surrounds, glazed with putty or fixed with beads and prepared to receive new glass panes complete all as specified and directed.

S&F of 3mm sheet glass, ordinary quality and glazing with oil putting in squares nexc 0.50 sqm each complete all as specified and directed.

S&F of 3mm sheet frosted glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed.

S&F of 3mm thick figured glass sheet fixed with beads or oil putty complete all as specified and directed.

S&F in repairs 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repairs 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F in repairs 150mm size extruded aluminum alloy handle, fabricated type anodized (ISI Marked) complete all as specified and directed.

S&F in repairs 1.5mm thick plain colour PVC sheet fixed with rubber based adhesive in windows/ventilators etc. including hacking out/removing old from metal /wooden frame complete all as specified and directed.

S&F in repars of 100mm long, mild steel pressed handles, oval type, stove enameled black complete all as specified and directed.

S&F in repairs butt hinges, 100mm size, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs butt hinges, 75mm size, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs of 150mm long, mild steel barrel tower bolts, stove enameled black, with bright bolt complete all as specified and directed.

S&F in repairs of 100mm long, mild steel barrel tower bolts, stove enameled black, with bright bolt complete all as specified and directed.

S&F in repairs 300mm long mild steel, sliding door bolt, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four or bolt plate and two on staple plate complete all as specified and directed.

S&F in repairs 150mm floor door stopper of aluminimum alloy body and tongue anodized with hard drawn steel spring complete all as specified and directed.

S&F in repairs 300mm long, mild steel ordinary rat tail red pattern spring including roller plate complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, aluminium body, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F in repairs mild steel wire cloth of 0.56 mm, nominal dia of wire and averaging of width of aperture 1.18mm, fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs 20-25 mm dia chromium plated steel drapary curtain rod with bracketes including necessary drilling holes and fixing with rawl plug and suitable screw in wall including designer dom for curtain rod complete all as specified and directed.

Dismantling steel rolling shutter of any size, steel work including door, gate etc. complete all as specified and directed.

S&F of 1.25mm thick of laths of steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, push pull or manual type complete all as specified and directed.

All as per item No 49.00 above here-in-before but gear operated type with bevel gear box and crank handle complete all as specified and directed.

Taking down the existing rolling shutters from the existing opening and refixing the same in position after carrying out necessary repairs including oiling, greasing, easing out etc. complete all as specified and directed.

Demolition of PCC in ground floors and paving not exc 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor hearh or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 7 to 8 mm thick ceramic (non skid) tiles area of each tile exc 0.11 sqm but n exc 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles bedded over and including 15mm thick pigment to match the colour of screed in cement mortar 1:6 complete all as specified and directed.

M&L for any coloured glazed ceramic tiles size of tiles 450x300x7mm thick on vertical surface such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in colour cement to match including 10mm thick cement plaster with cement mortar 1:4 complete all as specified and directed.

M&L for any coloured vetrified tiles size 600 x 600mm x 10 mm thick as in floors set and jointed in neat cement slurry over and including 15 mm thick screed bed in cement mortor 1:6 and pointed in coloured cement to match the colour of tiles complete all as specified and directed.

M&L for any coloured any vetrified tiles size 600 x 600mm x 10 mm thick as on vertical surfaces, such as skirting/dado set and jointed in neat cement slurry and pointed in coloured cement to match colour of tiles over and including 10 mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes complete all as specified and directed.

M&L for PCC (1:4:8) 75mm thick, type D-2 (using 40mm grade stone aggregate) as in base complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (using 20 graded stone aggregate) as in pavement/plinth protection, plinth protection shall be laid in alternate bays and joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen mixed with 3 part of sand) surface finished fair and even complete all as specified and directed.

M&L for PCC (1:4:8) 100mm thick, type D-2 (using 40mm grade stone aggregate) as in base complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in flooring, pavement, hardstanding, hardstanding shall be laid in alternate ways and joints shall be filled with bitumenastic gola with 80/25 bitumen (1 part bitumen and 3 parts sand), finished the surface fair and even complete all as specified and directed.

M&L for 20mm thick screed bed in CM (1:6) as in sub base of floor complete all as specified and directed.

M&L for chequered cement concrete tiles pre polished lacuqer and glossy finish 30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors complete all as specified and directed.

Dismantling plain or corrugated steel sheeting with ridge, gutters, etc, any gauge, and thickness including nainital pattern roof covering, fibre glass reinforced translucent corrugated sheeting, fixed with J/L hooks or coach screws complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based profile steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F of Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, eaves board fixed with self tapping screws complete all as specified and directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L or J-type or cranked hook bolts/self tapping screw complete all as specified and directed .

Dismantling the existing ceiling board of any description fixed in any position with nails and S&F in position suspended false celling system using E Grid suspended celling grid system of M/S Everest industries Ltd or India Gypsum. The size of Grid shall be 600X600mm with GI frame work, main runner 39X24mm, cross tee 29X24mm and wall angle 22.2X22.2mm using 4mm thick High Pressure Stream cured non primered classic/designer variant E-Board ISI Marked IS No 14862-2000. Fibre cement E Board (thickness of board shall not be less than 6mm) to be placed in the gird of E Grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the pulins of the roof with butter fly clips complete all as specified and directed.

Dismantling unframed timber scantlings exc 40 sqcm and over in section any position complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not other wise provided complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 Cum, getting out hard/dense soil and returning, filling and ramming earth or broken rubble mixed with earth with around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed.

S&F of roof trusses (framed), trussed, purlins, post, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F of rolled mild steel Fe-410-w (grade E-250) quality A, framed work such as grills, gratings, angle for ventilators etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work complete all as specified and directed.

S&F of framed work of rolled mild steel conforming to Fe-410-W (Gde-E-250) quality-A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting, running rails and guides) and hanging, fastening and fixing complete all as specified and directed.

S&F of mild steel, plain black sheet 0.80mm thick in hearths; covering to door shutters; ducts, etc, cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, etc as required complete all as specified and directed.

S&F of welded steel wire fabric (weight not less than 4kg per sqm) fixed to wood or steel members complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coat synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coat aluminium paint over a coat of aluminium red oxide primer complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of primer to new wooden surface including preparation of surfaces exceeding 10cm with or girth complete all as specified and directed.

Demolition of mud in roof any thickness whether full thickness removed or part thereof including plaster and leaping complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions on existing surfaces complete all as specified and directed. Note : Water proofing compound shall be paid separately.

Supply only integral water proofing compound complete all as specified and directed.

M&L for cleaning of roof slab surfaces including sweeping clean and washing down with water to remove dust and providing water proofing treatment with polymeric standard water proofing membrane complete all as specified and directed. Note:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @1.20Kg/Sqm. (b) Supplying and laying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application including coping on the surfaces with torch application of membrane with 10cm over laps as required. (c) Applying two coats of aluminium paint @ 0.2 kg/sqm.

Demolition of reinforced concrete as in roof, floor, (other than ground floors), beams, stair cases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) with necessary scaffolding and protection as required complete all as specified and directed.

M&L for precast reiforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in bed plates, pintle block, columns, post, boundry pillars, window or door cills, anchorage blocks, etc with plain fair faces, including chamfers, weatherings, throatings, etc including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) in louvers and jallies 35mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

M&L for formwork to flat rough finished surface of concrete for chullah hoods, chajjas, troughs and similar items including edges any height complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 (using 20 mm crushed stone aggregate) as in chajja repairs at any height including providing and erecting at site conventional steel double scaffolding to reach at any height/any place of work on the external façade of the building including approaches, extensions, working platforms, ladders, lifting tackle for men and materials etc inclusive of covering by hessian cloth or tarpaulins, dismantling and taking away all materials after the completion of praposed work etc complete all as specified and directed.

S&F of mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F of mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape as required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc. including removal of debris complete all as specified and directed .

M&L for brickwork with subclass 'B' bricks straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as speciified and directed.

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick wall built in CM 1:4 complete all as specified and directed.

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick wall mixing with water proofing compound as per manufacturer instruction of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compound paid seperately.

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brickwork or concrete surfaces, finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm rendering in cement mortar (1:3) to ceiling and similar work finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for two coats of cement based paint on newly plastered surfaces of wall including preparation of surfaces over one coat of primer complete all as specified and directed.

M&L for two coat of oil bound distemper on newly plastered surfaces of wall including preparation of surfaces over one coat of primer complete all as specified and directed.

M&L for two coats of white wash on newly plastered surfaces as on ceiling including preparation of surfaces complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint (weather proof paint on external surfaces) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces at any height of building / tower complete all as specified and directed.

S&F in repairs 15mm dia PTMT bib taps screwed down screwed for iron pipe fixed in complete all as specified and directed.

S&F in repairs bib taps 15mm dia, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed in complete all as specified and directed.

S&F in repairs pillar taps, fancy type 15mm of PTMT with minimum weight 110 gm of any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm pillar taps, fancy type, cast copper alloy with capstan heads, chromium plated, screed down high pressure, with or without lettered 'Hot; or 'Cold' with long screwed shanks and fly nut, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in repairs 15 mm dia angle/stop cock cast copper alloy, fancy type, chromium plated screwed down high pressure complete all as specified and directed.

S&F in repairs 15mm bore concealed stop valve, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for unions pipe complete all as specified and directed.

S&F in repairs of towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 90gms) complete all as specified and directed.

S&F of tubular, towel rail brass chromium plated 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repairs chromium plated brass shower roses 125mm size fixed to steel pipe as union complete all as specified and directed.

S&F in repairs vitreous china urinal, half stall type including all fittings with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repairs vitreous china squatting pan orissa pattern size 650 x440mm white with integral footrest, including trap set and conection to trap, flushing pipe etc. including making good to floor complete all as specified and directed.

S&F in repairs vitreous china EWC 'P' or 'S' Trap, white including plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device suitable for EWC making good to floor fixing bolt complete all as specified and directed.

S&F in repairs PVC low level flushing cistern, 10 Ltr capacity, valveless syphonic action type, white with ball valve flat back and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern complete all as specified and directed.

S&F in repairs plastic water closet seat cover white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinges device complete all as specified and directed.

S&F in repairs chromium plated jet spray/health faucet (ABS body) suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position in all respect complete all as specified and directed.

S&F in repairs 15 mm dia, chromium plated two ways bib cock with wall flange for fixing in pipe complete all as specified and directed.

S&F in repairs wash basin, vitreous china (flat back or angle back type) size 550x400mm white including cutting for & pinning in ends of brackets or erecting stand, brackets, CP brass waste coupling and waste pipe of standard length complete all as specified and directed.

S&F of 32mm dia, waste coupling of CP brass (half and full threaded) complete all as specified and directed.

S&F of PVC connections 15mm dia and 450mm long with PTMT nuts complete all as specified and directed.

S&F of PVC connections 15mm dia and 600mm long with PTMT nuts complete all as specified and directed.

S&F of 32mm uPVC waste pipe for wash basin/sink and urinal complete all as specified and directed.

S&F of 40mm uPVC waste pipe for wash basin/sink and unrinal complete all as specified and directed.

S&F in repairs 100 mm dia PTMT grating with waste hole complete all as specified and directed.

S&F in repairs PVC bath cabinet with mirror 350x450mm complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard board railing 60 cm long complete all as specified and directed.

S&F in repairs stainless steel plate rack (utencil rack for kitchen of size 750 x 600 x 250mm and min 0.80 to 1.00 mm thick fixed with stainless steel screw and rawl plug complete all as specified and directed.

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling/waste pipe; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs kitchen sink waste coupling, including PVC waste pipe complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Refixing 15mm dia steel tubing and connection in new or old position (in wall or floors/trenches ) complete all as specified and directed.

Refixing 20mm dia steel tubing and connection in new or old position (in wall or floors/trenches) complete all as specified and directed.

S&F of 15mm dia GI tubing, medium grade, with all fitting and fixed to walls or laid in floors/trenches complete all as specified and directed.

S&F of 20mm dia GI tubing, medium grade, with all fitting and fixed to walls or laid in floors/trenches complete all as specified and directed.

M&L for cleaning and removing all scale and dirt etc. from tanks and from mounts of circulating pipes etc. capacity of tanks exc. 250 Ltr and nexc. 500 ltr complete all as specified and directed.

All as per item No 141.00 here-in-before but capacity of tanks exc. 500 ltr and nexc. 1000 Ltr complete all as specified and directed.

Disconnecting of existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity exc. 250 Ltr nexc. 500 ltr complete as specified and directed.

S&F in repairs moulded polythene water storage tank of 500 ltr capacity (3 layered) hoisted and fixed in position and float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and including (minimum weight 15mm-142gms) and nipple suitable for HDPE water tank complete all as specified and directed.

S&F in repairs moulded polythene water storage tank of 1000 ltr capacity (3 layered) hoisted and fixed in position and float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and including (minimum weight 15mm-142gms) and nipple suitable for HDPE water tank complete all as specified and directed.

S&F in repairs HDPE/plastic water storage tank lid/tank cover complete all as specified and directed.

S&F of 21-22 inch dia galvanised mild steel pan mortar (tasla/ghamela) not less than 1mm thick with for 04 Nos bolt of 5-6mm dia with 4 Nos nut bolt with 4 Nos washer including fixing on water storage tank as tank cover complete all as specified and directed.

S&F in repairs 15mm dia, float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe screwed for iron pipe and fixed (15mm dia minimum weight 142gms) complete all as specified and directed.

S&F in repairs 15 mm nipple suitable for HDPE water tanks including necessary driling holes etc fixed complete all as specified and directed.

S&F in repairs 20mm dia, float valves high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screw for iron pipe (20mm dia minimum weight 210gms) complete all as specified and directed.

S&F in repair 20 mm nipple suitable for HDPE water tanks including necessary drilling holes etc fixed complete all as specified and directed.

S&F in repairs 15mm bore dia of ball brass valves, high pressure with polythene float and fly nut, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repairs PVC(SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with and including PVC clip complete all as specified and directed.

S&F in repairs PVC(SWR) branch piece, single T equal or unequal 110 mm dia complete all as specified and directed.

S&F in repairs PVC(SWR) bend 110 mm dia without access door complete all as specified and directed.

S&F in repairs PVC(SWR) bend 110 mm dia with access door complete all as specified and directed.

S&F in repairs PVC(SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and directed.

S&F in repairs PVC(SWR) 110mm bore vent cowl complete all as specified and directed.

S&F in repairs PVC(SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F in repairs PVC(SWR) bend 75 mm dia with access door complete all as specified and directed.

S&F in repairs PVC(SWR) bend 75 mm dia without access door complete all as specified and directed.

S&F in repairs PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement concrete type B-1 1:2:4 complete all as specified and directed.

S&F of PVC(SWR) 75mm of floor trap, plain with grating including jointing with solvent cement concrete type B-1, 1:2:4 complete all as specified and directed.

S&F of PVC(SWR) 75mm of multi floor trap, plain with grating including jointing with solvent cement concrete type B-1, 1:2:4 complete all as specified and directed.

M&L for attending /cleanig daily complaints of blockage of floor traps, WCs (Indian/European) WHB traps, kitchen traps, urinal traps etc at ground floor or above ground floors with and including necessary T&P as required for this purpose. Note : (a) Complaint slip shall collected by the contractor/supervisor from MES complaint cell and submit the same duly signed by the occupant at 1630hrs in the complaint cell. It will be responsibility of contractor to ensure their attendance & completion of complaints. (b) If any complaint not resolved within 24 hrs the recovery @ Rs 500 per complaint per day will be charged from RAR or Final Bill. (c) During cleaning of blockage remove grating will be refixed in existing position with white/grey cement after clearing of blockage from trapes. (d) The contractor will ensure the cleaning /cleaning of all the complaints (Irrespective of Nos) within 24 hrs by deploying additional sewer man /safaiwala if needed. Nothing extra shall be paid on this account. (e) Contractor shall be solely responsible for supplying all the safety measures required by the sewer man/safaiwala during working hours. (f) All the waste material/sludge shall be disposed of out of MoD land.

Taking out RCC cover slab of septic tank of the 100 users capacity carefully, taking out the sludge including foul water collect the sludge in closed container and burried the same in earth pit below 30 cm of the gound level with in the defence land where directed by the Engineer-in-charge to a distance exc 250 m and n.exc 500 m, returning, filling in the earth in excavated pit after complete removal of sludge from the container, inlet and outlet pipe, M.S ring and septic tank complete cleaning with fresh water as directed and placing the RCC cover slab in position and set in CM 1:6 complete all as specified and directed

All as per ser item no 165.00 here-in-before but 50 users capacity

All as per ser item no 165.00 here-in-before bu 25 users capacity

Cleaning of man holes of any size depth n.exc 60 cm to cleaned all as per item No 2 here-in-before complete all as specified and as directed.

Cleaning of man holes of any size depth exc 60 cm and n.exc 1.20 mtr cleaned all as per item no 2 here-in-before complete all as specified and as directed.

Cleaning man holes of any size depth exc 1.20 sqm cleaned all as specified all as per item No 2 here in before all as specified and directed

M&L for dewatering/ desludging of existing main sewage receiving tank of size 6m dia and 5 m deep (inner tank and outer tank) by sewage sunction machine truck mounted equipped with sewage storage tank and dispose off foul material/sludge out side the defence land on the location enmarked by civil authorities complete all as specified and directed

M&L for dewatering/desludding from existing soakage well by sewage suction machine truck mounting equipped with sewage storage tank and removing/dispose off foul material/sludge out side the defence land on the location enmarked by civil authorities complete all as specified and directed.

(a) size 2.4 M dia X 3.0M deep

(b) size 1.8 M dia X 3.0M deep

(c) size 1.2 M dia X 3.0M deep

Material and labour loose filling with aggregate of guage 80 mm to 150 mm as in soak well /sokage pits /filter beds with broken bricks including removed old brick beds complete all as specified and as directed.

M&L for cleaning of shocked sewage line of any description and any dia from man hole to man hole with sewage cleaning rod washing down with fresh water and disposed off the sludge all as specified and directed . The complaint where cleaning is not possible by rodding and is to be cleared by braking existing line the item will be paid separetely in item herein after

M&L for cleaning of underground sewage lines of 150mm bore by excavation and breaking (Minimum two length) and removing the blockage, laying new pipes, re-joining with old pipes including haunching the new pipes with PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) in all situations where cleaning is not possible otherwise including returning, filling and disposal of surplus soil outside MoD land etc. Complete all as specified and directed by Engr-in-charge

Demolition of reinforced cement concrete of any description as in man hole / septic tank cover slabs in any position complete all as specified and as directed.

M&L for precast reinforced cement concrete type B1, (1:2:4) with (using 20 mm graded stone aggregate) as in man hole / soak well cover slab set in CM 1:4 all as specified and as directed

M&L RCC type B-1 (1:2:4) with (using 20 mm grades stone aggregate) as in slabs as in septic tank cover slab set in CM 1:4 all as specified and as directed

Use&waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping)

M&L for for rendering cement plaster 10 mm thick in cement mortar 1:4 on concrete surface such as soffits of RCC, chajja, roof projection columns and beams etc finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in CM 1:4 as in soak well complete all as specified and directed.

Excavation in trenches not exc. 1.5m wide & not exc. 1.5mdeep and getting out in soft/loose soil for foundation etc, complete all as specified and directed.

Returning filling in, including spreading, leveling watering well roaming in layers not exc. 25cm thick each layer complete all as specified and as directed by the Engineer-in-Charge.

Removal of surplus soil to a distance of exc. 50 meter but nexc 250m depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed.

Dismantling of RCC any size or any type of pipe and bore jointed in cement mortar of any size and description complete all as specified and directed.

M&L for 150mm dia of Internal diameter of RCC pipes drain pipe, class NP-2 type, laid in trenches and jointed as specified & directed by the Engineer-in-Charge.

M&L for 200mm dia of Internal diameter of RCC pipes drain pipe, class NP-2 type, laid in trenches and jointed as specified & directed by the Engineer-in-Charge.

Concrete bed to drain pipe including packing under haunching against the side of pipes, 150mm dia, in cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) after laying and testing of pipe complete all as specified and directed.

Concrete bed to drain pipe including packing under haunching against the side of pipes, 200 mm bore, in cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) after laying and testing of pipe complete all as specified and directed.

M&L for cement conctete type B-1, 1:2:4 using 20mm graded stone aggregate as in benching and coping complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation etc complete all as specified and directed.

M&L for non skid coloured ceramic edge cut tiles 7-8mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but n.exceeding 0.11sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tiles over including screed bed 15mm thick in cement mortar (1:4) for laying floor finished complete all as specified and directed by Engineer-in-Charge

Demolition and breaking up or down any type and any size of pipe fixed in any position all as specified and directed

S&F PVC (SWR) pipes 110 mm dia. single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) 110mm dia, branch pieces (single Y) equal or unequal complete all as specified and as directed.

S&F PVC (SWR) junction single (single 'T') equal or unequal (110 mm dia)

S&F PVC (SWR) bend 110 mm dia with access door complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia. single socketed, in any length with rubber ring joints, fixed to wall incl demolation of existing pipe complete all as specified and as directed.

S&F PVC (SWR) branch pieces (single Y) equal or unequal (75mm dia.)

S&F PVC (SWR) junction single (Single 'T') equal or unequal (75 mm dia)

S&F PVC (SWR) bend 75 mm dia with access door complete all as specified and as directed.

S&F PVC (SWR) bend 75 mm dia without access door complete all as specified and as directed.

S&F PVC (SWR) 75 mm bore vent cowl complete all as specified and as directed.

S&F PVC (SWR) floor trap plain 75mm dia of outlet in mm with grating including jointing with solvent cement

Dismantling of wrought iron or mild steel work of any description not other wise provided complete all as specified and as directed.

Dismantling of old chain link fencing including flat iron, line wire complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion from natural ground and making good disturbed ground

S,&F for hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; and similar work posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply only for chain link MS galvanisd fencing, any size or type etc & fixed to angle iron post complete all as specified.

Fixing only chain link fencing including line wires,any mesh, size and type to any type of standard, rails, straining bolts, etc including provission of binding wire complete all as specified and as directed.

S&F mild steel bolts screw (machine made) with hexagonal or square head at one end and screw the other or screw both ends, each screwed ends to be fitted with washer and one hexagonal or square length of nut exceeding 5cm and not exceedign 10cm and diameter of neck in mm 11 to 15mm complete all as specified and directed

M&L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate in foundation and mass concrete complete all as specified and directed

S&F for galvanized, 2 strand steel barbed wire 2.24mm dia barbard with 2mm dia barbs at 75 mm spacing straing and fixing to any type of standerd rails strainig bolts, including and tying at crossing with and provision of galvnized mild wire, staples or steel pins etc including distmantling of unservisable barberdd wire complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20mm graded aggregate as in coping including necessary form work complete all as specified and as directed

Material and labour for 100mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in sub base the surface fair and even complete all as specified and as directed.

Material and labour for 250x250x22mm/300x300x25 mm thick PCC designer Pre-polished tiles (Factory make and approved size) as in floors, set & jointed in neat cement slurry and pointed in grey cement with pigment over and including 20mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 61409.00

M/S HARSH VIKAS GALAR ENGINEERING

TANUJ CONST. CO.

M/s SHIVRATAN CONSTRUCTION