Special Repair of Primary Health Centre at Village Kalsana in District Kurukshetra

Amount

Scraping Cement plaster (HSR 8.32 (c))

15mm Thick Cement Plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10).

Dismantling tile terracing ( HSR. 8.38 (b)) In cement

Removing doors and windows (wooden and steel) together with the dismantling of walls (HSR - 8.17)(a) doors

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR - 8.5) (d)

Scraping White washing & Colour wash (HSR-8.32) (a)

Preparation of plastered surface for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk miti including finishing the surface to the required finish complete. (HSR 16.52) (a)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Painting two coats with ready-mixed exterior paint in all shades on newly plastered or concrete surface of walls. (HSR 16.26).

White Washing (HSR 16.47) Two coats

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58).

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc.(HSR 16.61 )

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. HSR-14.92 (a)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR-14.89)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean.(HSR-13.14)

Providing two coats of exterior acrylic emulsion paint. (HSR-16.79(b)

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas. (HSR-18.30(b)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ’S’ TRAP with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item no.30.3 above HSR-30.6 (i)

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid HSR-30.13 (i)

Providing and fixing in position best Indian make lavatory suites (with full anti splash rim in vitreous Chinaware and all other necessary fittings as fully described in item No. 30.41 above. (HSR-30.42) white (ii)

PROVIDING AND FIXING IN POSITION ON BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE (HSR-30.45)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR-30.75 (a))

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR-30.75 (c)) 4.00

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (HSR-30.119 ( c ))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION. (HSR-30.82 (a) (ii))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P.BRASS INLET CONNECTION 15 MM WITH 375 MM PIPE AND C.P. BRASS NUTS (HSR-30.83)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hot- pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (HSR-17.93) (a) (iii) 35mm

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak, conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (HSR-17.92 (ii))

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W.R. grade, hot-presses, including cost of iron hinges,screws,chocks/cleats,stops, and nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). (HSR-17.91) (b) 35mm dia

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak, conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (HSR-17.92) (ii) 35mm

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete (HSR-18.34) ( a )

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete (HSR-18.34) ( d )

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR-13.64)

Cement Concrete 1: 1 ½: 3 with stone aggregate 20mm nominal size in foundation and plinth (HSR-10.42)

Preparation of ply wood surface for painting inlcuding sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3).

Painting two coats excluding priming coat with ready mixed paint in all shades on new wood work. (HSR - 16.4)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR-16.5)

Painting two coats with ready- mixed paint for metallic surfaces in all shades on old steel or iron work (HSR-16.18)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Note: In case of any difference in the unit & nomenclature of any of the HSR items depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

KEWAL KRISHAN

The Gadhali Coprative L and C Society Ltd.