Establishment of 14 bedded fully equipped PICU of T.B. ward (New Construction) in the B. P. Civil Hospital, Nagaon (Construction of 14 bedded PICU with MGPS with additional oxygen outlet, manifold plant room, donning and doffing area with doctors lo

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Excavating, Supplying and filling of local earth(inculding Royality) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Vertical surface such as walls (any thickness), parapet walls, partitions and the like including attached pilasters, butresses, plinth and string courses and the like.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement : 3 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. omplete: 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete

Float glass panes of nominal thickness 5 mm (weight not less than 12.00 kg/sqm)

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring and tread of steps in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000mm length and L-hape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineerin

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing toilet paper holder : C.P. brass

Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing & fixing 100 mm sand cast iron grating for gully trap

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion i) single socketed pipe 75 mm diameter

110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -PVC rain water pipes by means of 50 X50X50 mm hard wood plugs ,screwed witjh MS screws of required length including cutting brick work and fixing in cement morter 1:4 (1 cement :4 coarse sand) and making good the walls etc. complete. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm

Single tee without door 75x75x75 mm

Bend 87.5° 75 mm bend

110 mm bend

Shoe (Plain) 75 mm Shoe

110 mm Shoe

Providing and fixing uplasticised PVC connection pipe with brass unions 30 cm length 15 mm nominal bore

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) alround SW pipes including bed concrete as per standard design. 150 mm dia SW pipe

Providing and fixing square - mouth SW gully trap grade 'A' complete with CI grating brick masonry chamber with water tight CI Cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 Kg) and frame to be not less than 2.70 Kg as per standard design. 100x100mm size 'P' type With FPS bricks class designation 7.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 32 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25mm nominal bore

45cm length 20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X4 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

2 way 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mm X 150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 510 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

TV antenna socket outlet

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2 + 12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Double pole

Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required. 63 amps TPN

100 amps TPN

200 amps TPN

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 510 mm sweep

Supply of Medium class GI pipe for running of UG cable of 80mm dia.(Jindal make)

Supply of Medium class GI pipe for running of UG cable of 100mm dia.(Jindal make)

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Supplying, laying/ fixing, testing and commissioning of following thickness resin bonded fiber glass pipe section insulation having density 80 kg/cum or mineral wool (non combustible) having density of 144 Kg/ cu m duly covered with a layer of 120 gm/sqm polythene sheet (vapour barrier) on existing pipe and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip (as per IS:1322 as amended up to date ) at joints etc. as per specifications and as required. 75mm

SITC of online 3 phase UPS system with 30 minutes back up including batteries and battery rack, connecting cables etc

Suppy, Installation, Tesing and commissining of iquid cooled turbo charged with after cooler, developing 900HP liquid cooled, @ 1500RPM, V type electric start, compression ignition, 4 stroke designed to run continously 1500 RPM confirming to IS 10001 ISO-3046, BS-5514 standard with an overload capacity of 10% for one hour in every 12 Hrs.Diesel Engine Generator

Supplying, Fixing and Fitting of not less than 72 mm thick partition wall with 11 mm thk white coloured surface finished High Density Fire and water retardent WPC boards fixed over a frame of 25 x 50 x 2 Aluminium sections comprising of vertical and horizontal members fixed at a distance of not more than 600mm C/C in both directions. The 11 mm thick WPC board to be fixed on both side of the frame with 25mm drywall screw at 300 mm c/c. to be complete in all levels as per design and as directed by the department.

Providing ditting and fixing of 30 mm thk BWP grade green/century/ or equivalent)solid core flush door with 6mm glass panels fixed on rebate on the face and timber beads on back. The edges of the flush door shall be finished with 6mm thk teak wood liping. The timber beads and teak wood lipping shall be polished as per the approved shade of colour and the door to be finished with 1 mm thk laminate of Greenlam/Century/Merino make on both sides as well as the rebate including nessecary harware fittings like 100 mm SS hinges and screws, complete at all levels as per design and as directed.(lock, door closer/floor spring, tower bolt) to be measured seperately.

Providing, supplying and fixing of Frameless Single leaf/double Swing Glass Door of Dorma/ Ozone or equivalent make in glazing using 12mm thick toughened glass of Saint Gobain / or approved equivalent with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, specifications and direction of Engineer in charge. Single Leaf Door with Dorma or Equivalent Hardware’s as specified:- Swing Glass Door which includes each of Top Pivot PT 24, Bottom Patch PT 10, Top Patch PT 20, Floor Lock US 10, Strike Plate , Floor Spring BTS 75v, with pair of TGDIH SS Pull Handle 25 mm dia x 450 mm long and other accessories for self closing feature as per detailed drawings.

Providing fitting and fixing of Metaflex make double leaf PPGL Skin insulated door of size 2.2 m x 2.4 m , Hermetically sealed having 44 mm door panel thickness with thick pressure injected high grade PU (density 44kg/m3) as Door blade core material PPGL wall frame, rubber gasket seal, concealed drop seal, vissional glass panel of 300mm x 300mm, ball bearing himges, door closer on active leaf, door lock and SS D handle for smooth passage installation complete at all levels as directed.

Supply and installation of Merino /Greenlam (Nylon) series cubicles of width and depth as per specifications/ site drawings. Cubicle height will be 2003 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 no.s Nylon PA-6 made hinges affixed to the pilasters. Nylon PA-6 made coat hook and lock set are provided with each door. All pilasters will be made of 12 mm thick HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Aluminum made door stopper profiles with rubber linings for dampening the noise while door closing will be provided at the vertical ends of the pilasters. Pilasters will be anchored to the floor using Nylon PA-6 made adjustable legs .The bottom gap is 100-150 mm. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with aluminium made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing.

Supply, Fitting and Installation of 2mm Thick Homogenous Vinyl flooring of Diamond 10 Technology with PUR range including all accessories like welding rod strip etc installation complete as per approved shade complete in all levels. The product should to conform to Group "T" wear resistance as per EN649 clean room certified with Class "A" as per ASTMF 5100. The product should have flamabality resistance of Class BF1-S1, Slip resistance of Class R9 as per DIN 51130. The product should exhibit Anti Static behavior, resistance to Bacteria, resistance to Staining, sustainibility to Castor chair.

Supply, Fitting and Installation of 1mm Thick Homogenous Vinyl wall sheet of Diamond 10 Technology with PUR range including all accessories like welding rod strip etc installation complete as per approved shade complete in all levels.

Providing, fitting and fixing of 75 mm manually operated Black out Roller blinds with necessary hardware complete as per choice and as directed.

DRDO technology Bio-Degradable Bio-digester FRP tank of 5 cubic meter (2000 liters) caacity for 20users per day including Anaerobic Microbium Inoculum (AMI) 600 liters in barrels. Dimensions of tank (L) 2400x(B)1800mmx(D)1200mm

Providing fitting and installation (Bedside Curtain Partitions) ICU bed Anti Microbial curtains with U-Shaped & L- Shaped Anodized Powder Coated Pure Aluminium Cubical Tracks with Nylon Hooks including Polyester based Anti Microbial (4'*8') oval netted curtains of 18" complete as per approved sdade and design and as directed by the department at all levels. The powder coated aluminum channel is designed din such a way that it provides the strength for holding the curtains and minimizes the space constraints in hospitals and the curtains are designed in such a way that it would provide: Fresh air and ventilation to pass through from net at the top, privacy for the patients & to feel comfortable from outside disturbances, provide hygiene and enhance the aesthetic value of the hospital ICU.

Providing and laying of Micro concrete in old RCC structures like columns and floor/roof slab of the flowable consistency achieving a compressive strength of not less than 30N/mm2 after 24 hours at 300C with a density of not less than 2100 kg/m3 as directed by the engineer in charge.

Supply of surface/pendant mounted totally enclosed linear luminaire(Ingress protection IP-65),WI0831208G1(Wipro or equivalent make 1x20W LED Tube T8.

Supply of energy efficient Ceiling fan 1200 mm sweep (Make- USHA : Model Name :Energia 32 5 star in the existing arrangement.

Supply of heavy duty 600mm sweep, 900rpm exhaust fan in the existing hole of the buildintg, turbo force SP(Considering 10% discount and 18%GST

Supply of recessed mounting glare less LED down light of size 2'x2'(>120Lumen/watt) Crompton or equivalent make.(LCTLRP-24 FO-CDL).

Supply of sky cove LED strip light including Driver in pack(24W output) available in 3000K and 6500K Philips or equivalent make.(LED strip sky cove 5M WW with driver).

Supply of recessed mounting glare less LED spot light with 30000 burning hours with CRI>8015watt 3000K and 4000K CCT Beam angle 36Deg. And Vertical Tilt 30Deg) Crompton or equivalent make.(CDR212-12-40-SL-NWH).

Supply of LED flood light made of pressure die cast Aluminium Housing with toughened glass and high power LEDs and secondary lences with IP66 .System efficiency>=110LPW. Option for 3000K 10KV SPD included. Crompton or equivalent make.(LFLN-120-CDL/60-M

Supply,installation, testing and commissining of 315A Electrical panel made of sheet steel(1.6mm thick, CRCA) alingwith 600A Al Bus- bar(Vertical and Horizontal of size 60x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1875HX1200WX550D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department

Supply, installation, testing and commissioning of 250A Electrical panel meant for Raw Power made of sheet steel(1.6mm thick, CRCA) alingwith 500A Al Bus- bar(Vertical and Horizontal of size 50x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1000HX1050WX450D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department.

1” PIPE – BEND- FLEXIBLE PIPE-TIE Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. 3 ½ X 70 sq.mm

3 ½ X 95 sq.mm

3 ½ X 150 sq.mm

3 ½ X 300 sq.mm

1.5Tr Hi Wall Split A/C

15 Litres Geyser

41" LED TV

Supply and installation of mono ammonium phosphate based dry powder 1.3kg. Capacity fire extinguiser ball.

Supply and installation of mono ammonium phosphate based dry powder 04kg. Capacity ABC stored pressure type fire extinguiser.

Supply and installation of mono ammonium phosphate based dry powder 05kg. Capacity ABC stored pressure type fire extinguiser.

Supply and installation of clean agent gas based 05kg. Capacity ABC stored pressure type fire extinguiser.

Supply and installation of clean agent gas based 02kg. Capacity ABC stored pressure type fire extinguiser.

Supply and installation of 2kg. Capacity CO2 type fire extinguiser.

Video/Audio Input: IP video input: 32-ch, Two-way audio input: 1-ch, BNC(2.0 Vp-p, 1kΩ),Incoming bandwidth: 200Mbps, Outgoing bandwidth: 160Mbps,Remote connection: 128,CVBS Output:1-ch, BNC(1.0Vp-p, 75Ω) Resolution: 704×576(PAL); 704×480(NTSC),HDMI Output: 1-ch, resolution: 1920*1080P/60Hz, 1920*1080P/50Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Recording Resolution: | 8MP/ 5MP/3MP/1080P/UXGA/720P/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Audio Output: 1-ch, BNC(Linear Electrical Level, 600Ω), Synchronous Playback: 16-ch, VGA Output: | 1-ch, resolution: 1920*1080P/60Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Live view Playback: 5MP/3MP/1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF, Capability: 16-ch@720P, 8-ch@1080P, SATA: 2 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or 8HDDs, Interface Type: 1 SATA interface, Capacity: Up to 6TB capacity for each HDD, Array type: RAID0, RAID1, RAID5, RAID10, Network Interface: | 2 RJ-45 10/100/1000Mbps self-adaptive Ethernet interfaces, Serial Interface: RS-232, RS-485, Keyboard, USB Interface: 3, USB2.0, Alarm In: 4-ch, Alarm Out: 2-ch, Power Supply: 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz, Consumption (without hard disk and POE): ≤ 45 W, Working Temperature: -10 ºC ~ +5 ºC (+14 ºF~ + 131 ºF), Working Humidity: 10 % ~ 90 % (CAMERA NVR 32 CHANNEL,MAKE:HONEY WELL.) Video/Audio Input: IP video input: 16-ch, Two-way audio input: 1-ch, BNC(2.0 Vp-p, 1kΩ),Incoming bandwidth: 200Mbps, Outgoing bandwidth: 160Mbps,Remote connection: 128,CVBS Output:1-ch, BNC(1.0Vp-p, 75Ω) Resolution: 704×576(PAL); 704×480(NTSC),HDMI Output: 1-ch, resolution: 1920*1080P/60Hz, 1920*1080P/50Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Recording Resolution: | 8MP/ 5MP/3MP/1080P/UXGA/720P/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Audio Output: 1-ch, BNC(Linear Electrical Level, 600Ω), Synchronous Playback: 16-ch, VGA Output: | 1-ch, resolution: 1920*1080P/60Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Live view Playback: 5MP/3MP/1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF, Capability: 8-ch@720P, 8-ch@1080P, SATA: 2 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or 8HDDs, Interface Type: 1 SATA interface, Capacity: Up to 6TB capacity for each HDD, Array type: RAID0, RAID1, RAID5, RAID10, Network Interface: | 2 RJ-45 10/100/1000Mbps self-adaptive Ethernet interfaces, Serial Interface: RS-232, RS-485, Keyboard, USB Interface: 3, USB2.0, Alarm In: 4-ch, Alarm Out: 2-ch, Power Supply: 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz, Consumption (without hard disk and POE): ≤ 45 W, Working Temperature: -10 ºC ~ +5 ºC (+14 ºF~ + 131 ºF), Working Humidity: 10 % ~ 90 % (CAMERA NVR 16CHANNEL,MAKE:HONEY WELL.) Seagate (preferred) 3.5-inch, Capacity: 6TB, NVR-Ready, 164 cameras, 550 TB/year, 3 years warranty (Hard Disc for Camera 6TB) 2 Megapixel (1920 x 1080) High Resolution, HD720p Realtime Video Recording, True Day / Night, IP66 Rating, IR Range: Up to 30m, Vandal-proof Housing, 3 ROI. IE / Firefox Browsing, CMS control(Bullet camera, Make Honey Well 2 Megapixel (1920 x 960) High Resolution, HD 720p Realtime Video, True Day / Night Auto Switch, IP66 Ingress Protection, IR LEDs up to 30m, Vandal-proof Housing, 3 ROI. IE / Firefox Browsing, CMS control(Dome Camera, Make Honey Well) 10/100/1000 24 PORT ALL POE SWITCH WITH 2 SFP UPLINK PORT 24 PORT POE SWITCH GIGA (Make: NETGEAR) 10/100/1000 16 PORT ALL POE SWITCH WITH PORTS (183W) 16 PORT POE SWITCH GIGA MAKE: NETGEAR FINOLEX 0.5X4 PAIR UTP CAT 6 LAN CABLE (305MTR) ROLL CAT6 WIRE MAKE: FINOLEX NETRACK 6U/500 CKD WITH GLASS DOOR, FAN PDU. 6U Rack MAKE:NETRACK DLINK (RJ45 Connector) PATCH PANEL & PATCH CORD PATCH PANEL MAKE: DLINK PATCH CORD 1 MTR PATCH CORD MAKE: DLINK INSTALLATION, COMMISSIONING & PROFESSIONAL ENGINEERING CHARGES 1” PIPE – BEND- FLEXIBLE PIPE-TIE

Providing, fitting and fixing robe hook complete as directed and specified. MAKE-1: JAQUAR, MODEL NO. ROBE HOOK : ACN-CHR-1191N

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. ( MAKE-1: JAQUAR, MODEL NO. HEALTH FAUCET : ALD-CHR-573)

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). MAKE-1: JAQUAR, MODEL NO. CON-CHR-041KN (a) Continental / clarion (iii) 2-Way bib cock

Providing and fixing brass CP Pillar cock 200mm EXTENSION BODY of approved qualiity MAKE-1: JAQUAR, MODEL NO. FUS-CHR-29021

Variable Refrigerant Volume System Supply,Installation, Testing and Commissioning of Variable Refrigerant Volume type multi unit air-conditioning system complete with indoor and outdoor units with individual controller for cooling operations.The quoted price should include cost of all material, consumable, all taxes, labour, commissioning etc. (Make: Daikin) Outdoor Unit All Inverter Scroll Compressor(s) with variable refrigeration evaporating temperature enabled feature in outdoor unit capable of inverter control with 6 pole compressor motor. The inverter compressor should be capable of changing the speed in accordance to the variation in cooling or heating load requirement, back pressure control mechanism for efficient operation in low-load condition. The outdoor unit should be fitted with low noise, aero spiral design fan with minimum External Static Pressure of 75 Pa for easy discharge of Hot air, aero fitting grille, to reduce pressure loss. The outdoor unit should be capable of automatic refrigerant charge function. The heat exchanger shall be constructed with copper tubes mechanically bonded to aluminium fins to form a cross fin coil. Capacity: 16 HP (Heating & cooling / Cooling only)-2 Nos. SITC of VRF Evaporating (Indoor) Units Complete with single phase/ three phase low-noise centrifugal fan, cooling coil, filter, electronic expansion valve & Y Joints with wired remote control inlcuidng connecting the indoor unit with a power cable & plug top to power point provided near the unit (including Canvas Connection) SITC of VRF Evaporating (Indoor) Units Complete with single phase/ three phase low-noise centrifugal fan, cooling coil, filter, electronic expansion valve & Y Joints with wired remote control inlcuidng connecting the indoor unit with a power cable & plug top to power point provided near the unit (including Canvas Connection) Double Skin Ceilinf Suspended AHU Ceiling Suspended AHU -16.0 HP VRF /4500 CFM /static-125 mm wg /Coil-4 RD Dx/ 40 mm thick Double Skin/ Filters - Hepa filters / including AHU kit- 2Nos. SITC of Refrigerant Piping For VRF System Refrigerant Piping For Suction Gas with 19mm thick Nitrile Insulation Line Size: 28.6 OD - RMT 50 Supply, installation, testing and commissioning of extruded aluminium power coated 15°/30° linear grills of approved shade and make- Sqm 7 Refrigerant Piping For Liquid Gas with 13mm thick Nitrile Insulation Line Size: 12.7 OD - RMT 50 Vapour Barrier Mechanical Protection of Copper pipe insulation with glass cloth & UV Lag paint Line Size: 28.6 OD- RMT 10 Line Size: 12.7 OD- RMT 10 Supply, Installation, Testing & Commissioining of Shielded control cum transmission cabling between ODU & IDU 2C X 1.0 Sqmm Cu Cable in Riggid PVC Conduit duly supported and saddled as per specification & as directed by the consultant. (note : it is important to lay one spare cable for redundancy)-RMT 70 Drain Piping Providing and fixing condensate drain piping with u-PVC pipe with 9mm thick nitrile tube insulation of following sizes, One end on the pipe will be connected to the indoor unit of the air conditioner /AHUand the other end will be terminated to the nearest apron drain or suitable termination drain pipe complete with all fittings and support etc complete in all respect as directed by the engineer. 40 mm dia- RMT-35 Supply , fabrication & fixing of of GSS leak proof sheet metal rectangular ducting with slip on flanges as per IS 655 complete with turning vanes , companion flanges , structural support , sealing of all seams with a suitable metal sealant, completely leak proof as per drawings and as directed by the engineer. 0.60 MM (24 gauge)-Sqm 117 0.80 MM (22 gauge)- Sqm 60 Supply and fixing of internal duct lining for duct accoustic insulation with 15mm thick Nitrile Open cell elastometric nitrile rubber applied with rubber based adhesive, screw, washer complete in all respect as specified in specifications & drawings.- Sqm 25 Supply and fixing of duct thermal insulation with class 1 nitrile insulation on the duct using Dendrite or equiv. adhesive. 13mm- Sqm 155 Supply, installation, testing and commissioning of volume control damper for grills- Sqm 3 Supply, installation, testing and commissioning of moterised combined smoke and fire dampers made out of GI sheet of at least 120 minutes fire rating complete with GI damper of required size, smoke sensor etc as per specifications and shop drawings.-Sqm 1 Actuator & Control panels- Nos. 1 Starter Panels with VFD Drive all incoming, Outgoing 26.0HP /8500CFM- Nos. 1 Supply, installation and balancing of extruded aluminium power coated fresh / exhaust air louvers complete with GI dampers, GI Cowl & aluminium wire mesh birdscreen( Mapro)- Sqm 1

Supply and installation,Testing & Commissioning of Terminal Units(Gas Outlets)with Probes/Adaptes as per ISO 9001:2015 & 3 digit CE marked company.The outlet will be equiped with primary and a secondery check valvewith suitable pressure for (O2 Cleared for medical gas and pressure tested,inlet pipe can be swiveled 360 degree for ease of installation as per spesified and directed)

Supply and installation,Testing & Commissioning of O2 flow meter as per ISO 9001:2015 & 3 digit CE marked company made with chrome plated brass bodey,graduated flow tube and cover made of polycarbonate & unbreakable. Adjustable flow by needle valve(know) with micrometric regulation. Humidifier bottle is made of unbreakable polycarbonatematerial and is autoclavable

Supply and installation,Testing & Commissioning of ward vaccume unit as per ISO 9001:2015 & 3 digit CE marked company.with Regulator along with vaccume gauge,collection jar of 600 ml capacity reusable plastic collection bottle with over flow safety tap wall mounted type with bracket complete all as spesified and as directed.

Supply fitting and fixing of Copper Pipes as per Medical Grade: Llyod Certified 12 mm od X 0.7mm thickness

15mm od X 0.9mm thickness

22mm od X9mm thickness

28mmX.9mm thickness

42mmX1.0mm thickness

Supply and installation,Testing & Commissioning of area line pressure alarm with display of various faults indications and capable of monitoring maximum 3 medical gas service by means of pressure switches etc with audible warning with automatic reddit when the gas service return to normal as per ISO 9001:2015 & 3 digit CE marked company and as directed for the following area line pressure alarm. 3gas service O2,air and vaccum.

Supply and installation,Testing & Commissioning of isolation valves with brass body with nickel plate valve operating handle suitable for 12mm Od copper pipe to 42mm Od copper pipes with brass adapter as per standard spesification & as per ISO 9001:2015 & 3 digit CE marked company and sirevted for the following isolations. 12 mm od

Ventilator Probe for O2

Low pressure tubings

Supply and installation,Testing & Commissioning of Bed Head Panel 5ft Long as per ISO 9001:2015 & 3 digit CE marked company. These are panels as per customer choice of colour to maintain the aesthetics of the hospital along with accessories like 1No. Of IV hook 1.no. of utility BP Basket 1 No. of Monior tray 1 No of Aluminium Clamp for ward vaccum Unit and 2 no. of 6/16 amp Anti bacterial Switch and sockets.

Supply and installation,Testing & Commissioning of Oxygen Manifold Extendable type 16+16 size compatible as per ISO 9001:2015 & 3 digit CE marked company with middle frame with chain of individual Cylinder and high pressure annealed copper tail pipe with 1 end having brass adaptor and other end suitable for manifold non return valve and manifold will have 32 brass non return valve for individual Oxygen cylinder , middle frame with cercumferential MS felt duley powdercoated all as spesified and as directed

Supply and installation,Testing & Commissioning of semi Automatic gas control panel for O2 as per ISO 9001:2015 & 3 digit CE marked company., two stages of pressure regulators will be provided in the control cabinet for pressure regulation . One delivery pressure regulator .

Supply and installation,Testing & Commissioning of 5+5 Cylinder Emergency Oxygen Maniflold as per ISO 9001:2015 & 3 digit CE marked company. with two stage high flow rate regulator With NRV for every cylinder and copper tail pipe with top and middle frame for Oxygen

Supply installation testing and commisioning of Zonal Valve box that are fully designed to suit multiple operational requirement and ensure smooth working, considering space for mounting. The configuration of zonal valve box are described as below. 3 gas service O2 vacuum and air

Supply and installation,Testing & Commissioning of 10 Hp each double stage High Pressure Air Compressure (10 hp) each are designed for high pressure applications. These Compressures have extra heavy duty components and are designed for minimum maintance and maximum performance. High Pressure air compressure , Durable cast iron intermediate duty applications. 10 Hp Air Compressor motor including necessary fittings and accessories complete in all levels as directed by the department.

Supply Installation , testing and Commissioning of 1000ltrs Air reciever tank

Supply Installation , testing and Commissioning of Air Dryer Capacity 100 CFM

Supply Installation , testing and Commissioning of 3 Stage Bacterial Filter assembly

Supply Installation , testing and Commissioning of pressure reducing system with two numbers pressure regulators

Supply, installation,Testing&Commissionsing including connection of complete Vacuum plant. The pump should be achieve vacuum upto 737mm(290'Hg) for single stage upto 754.4mm(29.7 Hg) for two stage configuration at sea level. 10 HP each Double stage vacuum pump including necessary vacuum accessories like silencer, receiver tank(1000ltr) & vacuum bacteria filter.

PLC BASED AUTOMATIC TIMER MANAGEMENT SYSTEM WITH TOUCH SCREEN HMI

Supply and installation of the following furnitrures : Revolving Chair in Nurses Station

Supply and installation of ICU Nurse Station Table of 1200 x 600 x 750 mm with 25mm thick Pre-laminate(anti Bacterial) particle board top finished with 2mm edge lipping with Modesty Panel 18mm thick 450ht PLB modesty panels with necessary brackets with 25mm thick gable ends and cross beam under Structure Support including 65mm dia Grommet hole for Wire Management as per approved shade and design and as directed by the department complete in all levels.

Supply and installation of Doffing area Locker of size 600 mm x 450 mm x 600 mm with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels of Godrej/Hettich/Haffle made for shutters and drawers respectively complete as per design and as directed by the department.

Supply and installation of low height storage lockers unit with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels Godrej/Hettich/Haffle make for the shutters including fitting and fixing of 18 mm thick polished granite top complete as per design and as directed by the department.

Supply fitting and installation of High Resolution (HR) Signage as per the specifications and size as directed by the depaartment at all levels

MS PA ENTERPRISE