REPAIR TO CERTAIN B/R WORKS OF OTM AND MD ACCN INCLUDING REPAIR TO PATH,BERMS,RETAINING WALL ETC. AT MIL STN NAHAN UNDER GE CHANDIGARH.

Amount

Dismantling/taking out exisisting hessain base gelt or any other existing water proofing treatment from roof including cement plaster and exposing the top surface or RCC slab incl removing the dismatled debris to a distance exc 200m & n exc 250m.

Rendering 10mm avg thick on concrete surfaces over roof slabs, in cm 1:4, finished even and fair to receive roof treatment mixed with water proofing compound.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150gms/sqm) land on primed surface by forced application complete all as specified.

Water proofing treatment of roof slab with following procedure : (a) Cleaning the roof slab and vertical portion to remove any loose/unsound mayerials, dirt, dust and loose particle etc with mechanical means i. e wire brush/air blower as well as washing etc. (b) Applying a bonding coat of SBR latex based Dr fixit URP conforming to ASTM C-190-85/881 and cement in ratio of 1:1.5 @ 4.00 sqm/kg/cost along the junction of parapet walls and sloped RCC roof and marking of coping/gola with cement sand mortar 1:3 admixture with liquid intergral waterproofing compound Dr Fixit LW conforming to IS-2645-1983 @ 200 ml/50 kg of cement mix. (c) Applying first coat of prime seal (Primer) in ratio of 1 :1/2 (i.e one Part prime seal 1/2 part present water) following first coat with new coat. The second coat shall be applied with application of fiber mesh as per direction of Engr-in-Charge. Application of third coat as finishing coat also applicable. The primer shall upto full height at parapet wall to 1 mtr height at side wall Note: (i) All coat application as mention shall be 4.0 Sqm / KG/ coat with roller or paint brush on RCC surface allow it to dry as specified by Engr -in-Charge. (ii) The wk shall be executed by the auth applicator of the approved product / company.

S&F PVC wall cladding consisting of 5mm thick PVC sheet prelaminated printed on one side and plain colour on other side inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified.

5mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets.

Supply only liquid water proofing compound.(Make- Bostik, Dr fixit, Fosroc, or Equivalent)

S & F powder coated Gl frame work for false ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long with and including 8mm thick liminated laminated Gypsum board fixd to aluminum snap grid all as per clause 10.38.1 of SSR Part-I and as per manufacturer's instructions complete all as specified and as directed by Engineer -in-chargecomplete all as specified (Note:- taking down eletric items as like fan , tubelight ,LED light ,etc and refixing the same place)

Dismantling wrought iron or mild steel work of any description and in any position

Framed work such as grills, railings, gates, doors gratings, etc..with ends of bars shouldered and/or riveted,or forged into spikes,framed guard bar,con-forming to Fe.290.Gde-E-165

S&F complete at site and ready to use SS 304 as in grills & railings of any design and any pattern including fixing in concrete or with fasteners all including

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 250 & n.exc 500 ltr in capacity complete all as specified

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 500 & n.exc 1000 ltr in capacity complete all as specified

Providing and fixing anodised aluminium work for door windows, ventilators, casement/sliding shutters and partitions with extruded built up standard tabular and other sections of approval make fixed with rawl plugs and screws or with fixing clips or with expansion hold fastner incl neceesary filling up of gaps at junctions at top bottom & sides with required PVC neoprene belt etc. Aluminium section shall be smooth rust free straight mitred and jointed mechanically where ever required including cleats angles, aluminium snap beading for glazing/panelling, CP brass/stainless steel screw incl providing hinges/pivot and making provision for fixing of fittings where ever required. Note:- panel fillings other than aluminium filling and necessary fittings shall be measured and paid for seoparately under respective items.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots all as specified.

Rendering 15mm thick on fair faces of brick work or concrete surfaces , finished even and smooth without using extra cement on walls in cement mortar1:4, in patches (with WPC) complete all as specified and as directed by Engr-in-Charge.

Rendering 15 mm thick on brick work or concrete surfaces, finished even and smooth without using extra cement on walls in cement mortar 1:6, in patches complete all as specified and as directed by Engr-in-Charge

M&L Rendering 10 mm thick cement plaster in CM (1:3) on ceiling surfaces finished and smooth without using extra cement.

Two coats of exterior grade acrylic emulsion paint over a coat of primer on new wall surfaces including all necessary preperation of new wall surfaces, complete all as specified.

Two coats of acrylic distemper/ distemper oil emulsion (OBD) on new plastered wall surfaces of any description over 2mm thick wall care putty complete all as specified including preperation of surfaces

M&L for preparing newly plastered surfaces of ceiling and applying two coats of OBD over a coat of primer over a thin layer of putty complete all as specified.

M&L for preparing old plasterd or un plastered surface of walls and applying one coat of white wash complete all as specified.

One coat of white wash on ceiling on old wall surfaces including all necessary preparation and wetting and curing, complete all as specified.

One coat of cement base paint on old wall surfaces including all necessary preparation and wetting and curing, complete all as specified.

Two coats of cement base paint on old wall surfaces including all necessary preparation and wetting and curing, complete all as specified.

One coat of acrylic distemper/ distemper oil emulsion (OBD) on old wall/ceiling surfaces including all necessary preparation complete all as specified.of any description complete all as specified.

Two coats of acrylic distemper/ distemper oil emulsion (OBD) on old wall/ceiling surfaces including priming plastered surfaceover 2mm thick wal care putty, complete all as specified.

One coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

One coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

One coat of synthetic enamel paint over steel & iron surfaces of any description, not exceeding 10 cm in width or girth, unconnected with other painting or when painted in different tint including preparation of surfaces complete all as specified.

S & F in repair Galvanised mild steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed stainless steel wire staples

Cutting chases in stone wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

15mm GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors.

20mm GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors.

Taking down steel water tubing 15mm to 25 mm with all fittings from walls, ceiling and floors, complete all as specified.

S & F in repair Vitreous China wash basin, white Flat back , size 550x400 mm including brackets, waste cupling and waste pipe.

S&F in repair Vitreous China Squatting pan, 'Orissa pattern, size 580x440 mm white with integral foot rests including PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float,hockey stick and handle including brackets, In repair

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe and fixed.

S&F in repair 15mm dia bib taps CP brass,fancy type,long body, screwed down, screwed for iron pipe.

S&F in repair 15mm dia Angle cock chromium plated brass fancy type ,screwed down , high pressure, scrwed both ends for iron pipe.

S & F 4mm sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sqm in each pane

S&F in repair 25 mm dia curtain rod made of alu. Pipe with decorative lining coating,including brackets,with comp fittings

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs washers and wastes, including bedding in cement mortar to dward wall or including fixing cantilever brackets and connection union to pipe overall size 915x460mm and bowl size 410mm x330mm x160mm

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F 500 Ltr capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified

Dismantling water tanks 1000 ltr /500 ltr

S&F in repair Chromium plated brass Toilet paper holder

S&F in repair Chromium plated brass Jet spray with tube 1.5 mtr

S&F in repair Chromium plated brass 2 in 1 health faucet with hook 1mtr tube

S & F in repair vitreous china wash down water closet pan (pedastal pattern) white (exclusing fixing bolts, flushing cistern and flush pipe)

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm

Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) with old size bricks.

Brick work with sub class 'B' bricks half brick thick straight or curved on plan to any radius in half brick walls built in CM(1:4).

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and include 15 mm thick screed bed in CM 1:6

M&L ceramic coloured tiles8-9mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and include 15 mm thick screed bed in CM 1:6

M&L coloured vitrified tiles scratch and strain resistant tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and include 15 mm thick screed bed in CM 1:6

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L Glazed ceramic coloured,,tiles 450x350x6-7mm thick in vertical surfaces such as skirting,dados and risers to steps over and including 10mm thick in CM (1:4).

Black Granite stone ,20 mm thick as in kitchen platform incl rounding or bullnosing the exposed edges over 15 mm thick screed in CM 1:3

Dismanntling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering

S & F 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap fixed with coach screws and washers in roofs, walls etc with grade of zinc coating 275

All as pe item No 63 above but plain sheet as in ridges, hips, valleys, gutters, drip and straight flashings

S & F Fe 410-w(Gde E 250)quality B rolled mild steel in roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats etc

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Preparation & painting Old painted surface Synthetic enamel paint then two coats of painting (Ordinary tint) over CGI sheeting /surface of any description, Over 10 cm in width or girth

Preparation & Priming with red oxide zinc chrome then two coats of painting ( New surface )Synthetic enamel paint (Ordinary tint) over CGI sheeting /surface of any description, Over 10 cm in width or girth

Taking down chowkats or frames without taking off shutters exc 1.50Sqm but nexc 4.00Sqm

Taking down Chowkhats or frames without taking off shutters from the frame not nexc 1.5 Sqm

S & F Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

All as per item No 72 above but size 125mm x 60mm

M & L 35mm plain framed panelled shutter (min 2 panels) with lock rail and panel of 9mm BWP commercial ply on both faces. The size of rail and stile as per IS 1003(part I)

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S & F Galvanised mild steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed stainless steel wire staples

Taking down shutter and refixing the same after easing & minor altearation in sizes area not nexc 1.5 Sqm

S&F in repairs factory made Box type steel window steel frame 80mmx60mm(peripheral) and 80mmx75mm(intermediate memebrs)made out out of cold rolled 1.25mm thick sheet having steel window/ventilator shutter of MS tabular section of size 50mmx20mmx1.10mm thick fixed with box type hollow tabular section beading for glazed and wire shutter handle of 100mm size made out of Z section 2 Nos MS stove enameled black bolt of size 120mm 02 Nos, 150mm mild steel hook and eyes with and including 02 coats of synthetic enamel paint over a shop coat primer, complete all as shown in Drg No TD-219/220R/Sh 1/3 to 3/3 of HQ CE Chd zone. Note:-The rate is inclusive of makiking good & matching with existing surface.

All as per item No. 79 above but without glazing bar

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

M&L for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width tuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of lain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 125 mm Extruded aluminium alloy handles, fabricated type, anodised

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Painting of new wooden surface of any description ,not otherwise described and two coats of synthatic enamel paint over a coat of pink primer, incl prepration of surface

Preparation of new or previously untreated surfaces of steel or iron any description, over 10cm in width or girth,not otherwise described and two coats of synthatic enamel paint over red oxiede primer

Demolition of brickwork or stone/boulder masonary, built in lime mortar including quoins arches, pillers etc, but excluding ashlar facings, dressed stone work and precast concrete article built in cement mortar or cement lime mortar

S&F in repairs 10 ltr capacity PVC vlaveless syphonic action type flushing cistern low level,white with inlet ball valve,float and handle including brackets.

S& F in repair 15mm dia Ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S & F in repair 110MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S & F in repair 75 MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S & F in repair 110MM PVC SWR Bends any radius

S & F in repair 75 MM PVC SWR Bends any radius

S & F in repair 75MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S & F in repair Continuous (piano) hinges 30 mm wide , mild steel, bright finish or electrogalvanised.

S&F in repair 100 mm Hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws

S & F in repair 19mm particle board, medium density, flat pressed single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work

S&F in repair Brass chromium plated shower rose 125mm size,with complete fitting

S & F in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange

S & F in repair Door strip (snake guard strip)

S&F in repair 5.00mm thick polycarbonate glass sheet (unbrreakable)corner shelf set(Consiting of three pieces) all as specified and as directed by Engineer-in-Charge.

Taking down shutter of any description n exc 2.00 Sqm

S&F in repairs aluminium tower bolt of extruded section, 150mm length of bolt and fixed with screws, complete all as specified.

S&F in repairs 125mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified.

S&F in repairs 250mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified.

S&F in repairs aluminium door seal of length 90cm to 105cm long fixed to door shutters complete.

S&F in repairs aluminium door stopper double legged with rubber shoe 75mm long fixed to door shutters complete.

Taking down aluminium door shutter carefully from frames for servicing / including replacement of broken pivots, tightening of joints of rails and styles etc complete and refixing in the same opening to obtain smooth functioning of the door.

S & F in repairs door closure hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) weight between 61 to 80 kg in repair

S & F in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete.

Taking down aluminium shutters of any description, area exc 1 sqm and not exc 2.00sqm each complete all as specified.

Taking down aluminium shutters of any description, area n. exc 1 sqm each complete all as specified.

S & F Door closure hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) weight between 61 to 80 kg in repair

S & F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete.

S&F purpose made aluminium handle 75 to 100mm dia all as per sample with display of pull /push fixed on existing door shutter with necessary screws complete all as specified.

S&F in repairs purpose made aluminium handle 75 to 100mm dia all as per sample with display of pull /push fixed on existing door shutter with necessary screws complete all as specified.

S & F mild steel mortic lock vertical type size 100mm 4 levers

S& F 15mm dia Ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F in repairs mild steel mortice lock, vertical type, size 100mm 4 levers

S&F 100 mm Hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws

S&F in repair waste pipe 32mm dia flexible for Sink and WHB all as specified and as directed.

Demolitioin of cement conc in ground floors and pavings n.exc 15cms thickness (below or above GL).

M & L 75 mm thick Cement concrete type D2,1:4:8 (40mm graded crushed stone aggregate) as in sub base,path,floor, hardstanding complete as as specified and directed by Engineer-in-Charge

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, dolidly hearted built in retaining walls, abutment and sililar work.

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, dolidly hearted built in retaining walls, abutment and sililar work but except stone. (Stone recived from item No-89 above will be used)

Flush pointing to random rubble, uncoursed or brought up to coursed CM 1:4

M&L providing for PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in coping ,apex stone,

Cement concrete in surface channels and drains in cement concrete 1:3:6 type C1 (20 mm graded crushed stone aggregate)

Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

Sand filling under floors or in foundations including watering and consolidation

Machine pressed precast conctete interlocking paver block with gray cement and pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-35 Grade

Providing cement concrete Type B1 1:2:4 (20mm graded crushed stone aggregate) kerbs or mut stops, rounded or chamfered on edges

M&L Chequered cement concrete tiles 20cmx20cmx25cm thick with gre cement and pigment, set jointed and pointed in neat cement slurry in floors.including 15mm thick screed bed (1:4)

Demolition of existing cement concrete (reinforced) of any type and in any position not otherwise specifically provided for incl cutting of reinforcement steel for faclitating demolition

M&L RCC M-25 Design mix, using 20mm graded trap stone aggregate for concrete as in foundation, rafts, footings, plinth beams, bases of columns etc., complete.

M&L RCC M-25 Design mix, using 20mm graded trap stone aggregate for concrete as in walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top of footing including attached pilaster and buttresses etc., complete.

M&L TMT bars 10mm dia and over cut to length , bent to shape required including , cranking hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete.

Excavation over areas,n exc.1.5m deep and getting out in hard/dense soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in hard/dense soil

M&L rough excavation over areas n exc 1.5m deep and getting out as in any type of soils

Forming embankments including raising (or lowering) earth spreading in layer n exc 30cm thick watering, ramming/rolling and finishing to required size shape etc n exc 1.5m high from the base

All as per item No 145 above but exc 1.50m n exc 3.00m high from the base

All as per item No 145 above but exc 3.00m n exc 4.50m high from the base

All as per item No 145 above but exc 4.50m n exc 6.00m high from the base

M&L for removing surplus excavated material exc 1.50m but n exc 5.00km and depositing where directed.

M&Lcement concrete 1:2:4 type B2 (40 mm graded crushed stone aggregate ) in foundation filling and mass concrete for retaining walls, posts etc

Formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, plinth beams, vertical, finished rough complete.

Formwork to faces of walls, retaining walls, abutments, parapets and stair case railing and similar works incl attached pillaster, buttresses, vertical or batter, finished rough complete.

M&L broken stone or boulders hand packing (any thckness) at back of walls over arches etc and raising/lowering to the required level.

Labour only for preparation and applying one coat of synthetic enamel paint on old steel surfaces all as directed.(Paint will be issued under Sch B free for applying only).

M/S SHANTI SARUP DINESH CHAND