GE/CHM-87/2022-2023 PROVN OF TOILET FOR GUARDS, COLLASPSIBLE GATE, COVERED SHED AND OTHER MINOR WORKS UNDER AGE B/R III AT CHANDIMANDIR

Amount

Taking down chowkats or frame exc. 1.5 Square metre and n exc 4 Square metre with shutters, without taking off shutters from the frame, complete all as specified and directed.

Taking down chowkats or frame exc. 4 Square metre with shutters , without taking off shutters from the frame , complete all as specified and directed.

Taking down cement plaster / terrazo of any description from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete, all as specified and directed.

Demolition of brickwork built in cement mortar ,complete as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed.

Demolition of un-reinforced cement concrete of any description, in any position not specifically provided for, complete all as specified and directed.

Demolition of reinforced cement concrete, reinforcement cut as required to facilitate, in any position not specifically provided for, complete all as specified and directed.

Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets , complete all as specifed.

Taking up or down steel tubing and connections 15mm bore from walls, floors , trenches etc , complete all as specified and directed

Taking up or down steel tubing and connections 20mm bore from walls, floors , trenches etc , complete all as specified and directed

Surface dressing in any type of soil, not exceeding 15cm deep and getting out , all as specified.

Surface excavation in any type of soil, not exceeding 30 cm deep and averaging 30cm deep and getting out , all as specified.

Excavation in post holes (or similar hole) each in ant type of soil n.exc 0.50 cu m getting out, returning, filling and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering and removing surplus spoil at a distance not exc 50 metre and making good surfaces complete all as specified and directed.

Excavation in trenches in any type of soil, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier hole etc. and getting out, complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm depth , complete all as specified and directed.

Removal of excavated material to distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point , complete all as specified and directed.

Moorum/Red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering , all as specified and directed.

Hard core of gauge of broken stone or boulders, not exc 63mm , deposited spread and lavelled in layers n-exc 25 cm watered & rammed to a true surface ,complete all as specified.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete, all as specified & directed.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete, all as specified & directed.

Brick work with fly ash brick of class designation 7.5 (min. compressive strength 75Kg/sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks of class designation 7.50 all as per IS-1077-1992 (minimum compressive strength of brick 75 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

25mm thick plain cement concrete (1:2:4),type B-0 as in damp proof course to horizontal or vertical surfaces, including necessary form work,all as specified and directed.

Rendering 10mm thick in CM 1:3 on fair faces of concrete surfaces as in ceilings , finished fair and smooth, complete all as specified and directed.

Rendering 10mm thick in Cement and Sand mortar 1:6 over fair faces of brick / concrete ,finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work surfaces, finished even and fair in cement mortar (1:4), complete all as specified.

Rendering 15mm thick on fair faces of brick work surfaces, finished even and fair in cement mortar (1:4), inclunding using water proofing compound, complete all as specified. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

Material and labour for 50mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight, all as specified & directed by Engineer-in-charge.

Non skid ceramic coloured tiles, 10 to 12 mm thick of size 800mm x 1200mm as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick bedding layer in CM 1:4, complete all as specified and directed.

Glazed ceramic coloured tiles 10 to 12 mm thick of size 800mm x 1200mm as in skirting, dado or wall, set and jointed in neat cement slurry and grouted in white cement complete over and including 10 mm thick bedding layer in CM 1:3 complete, all as specified and directed.

Plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in flooring, finished even and smooth w/o using extra cement, complete all as specified and directed.

16-18mm thick mirror polished white onyx slab with crystallian background and white/golden light veins (as approved by Engr-in-charge), jointed with grey cement slurry and pointed in white cement mixed with admixture of pigment to match the shade of stone,over and including screed bed 15mm thick in cement mortar 1:4, complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40m graded crushed stone aggregate) as in sub base flooring, finished even ,all as specified and directed.

50mm thick PCC 1:4:8 type D-2 (using 40m graded crushed stone aggregate) as in sub base flooring, finished even ,all as specified and directed.

Vitrified ceramic coloured tiles, dark shade , area of each tile exc. 0.42 Square metre but not exc. 1.00 Square metre , 10-12mm thick, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6 , complete all as specified and directed.

All as per serial item No 36 hereinbefore but on vertical surface over 10mm rendering in CM(1:4).

Machine pressed Concrete interlocking paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning , complete all as specified and directed

40mm thick sand stone slabs, dressed close picked on exposed faces, set and jointed in cement and stone dust mortar 1:3 and pointed in cement mixed with approved pigment to match over and including rendering 10mm thick plaster in cement mortar 1:4 on wall surfaces , all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) or PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed pipe, etc., and making good, cutting not exceeding 10cm girth, complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m , all as directed.

2mm thick fibre glass reinforced translucent plain coloured sheeting with side lap, fixed with coach screws as in roof, wall etc, complete all as specified and directed.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surfaces of ceiling to prepare the surface even and smooth, all as directed..

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Square metre over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Square metre over new surfaces, all as directed.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification,two or more coats on new work, all as directed.

GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, all as specified.

Three coats of white wash on new plastered surfaces of walls including preparation of new plastered surfaces, complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer , complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including 2mm thick (average) wall care putty and sand papering, complete all as specified and directed.

Complete removal of existing treatment by using of wire brush /mechanical grinder including washing and rubbing down and applying two coats of white wash on walls, complete all as specified and directed.

Complete removal of existing treatment by using of wire brush /mechanical grinder including washing , rubbing down and stopping of distempered or painted surface and applying two coats of cement base paint over a coat of alkali resistant primer on walls, complete all as specified and directed.

12mm thick tinted and toughned glass as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes , rubber packing, L patch at bottom and top as required, all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, all as specified.

Stainless steel lock for 10-12mm thick glass door, having knob inside with three keys, satin finish, complete all as specified and directed.

200 mm long stainless steel handle, fancy type , fixed to toughened glass, complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for frame and shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings, whatever required including the cost of EPDM rubber/ neoprene gasket required with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as directed. Note: (i) The rate quoted shall be inclusive of neoprene beading ,aluminium snap beading ,glazing clips,cleats ,screw ,roller and locking arrangment. (ii) Glazing/ wire gauge shall be measured and paid separately.

Stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm , fixed with stainless steel wire staple/ wooden beads, complete all as specified.

Factory made solid PVC board 20-25 mm thick as in cup board shelf/ door, sag free thermal and electrically insulated, light weight, wrap free, impact resistant, fire resistant, termite resistant and smell free, complete all as specified and directed.

PVC Cupboard with frame and shutter in required sizes at site, made out of 18mm thick one side decorative lamination sheet/mica & other side balancing lamination consisting of carcass 18mm thick PVC sheet and all required brackets , screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish including all necessary fitting as per site requitment, all are specified and directed .

3mm thick aluminium composite panel sheet (ACP) of colour as approved by Engr In Charge, all as specified and directed.

Butt hinges 100mm long, of extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 type C-21, all as directed.

150mm long aluminum anodised handle, fabricated type, all as directed.

Door closer hydraulically regulated aluminum (die cast) body, designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg, complete all as specified and directed.

Fancy type handles (as approved by Engr in charge) for drawers/wooden shutters/kitchen cabinets or similar work of size 150 mm including necessary fittings ,complete all as specified and directed.

Stainless steel clip hinge of size 80 mm as in kitchen cabinet, complete all as specified and directed. MAKE : EBCO or equivalant.

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as directed.

40mm dia cup board knob, fixed with nut and washer of mild steel, bright finished, complete all as specified and directed.

Vertical "venetian blinds" with powder coated aluminium top channel with runner and 100mm wide superior quality non woven polyester fabric (chemically treated) alongwith bottom weights and link chain, pulling chain and tighting chain at the side, complete all as specified and directed.

Wall mounted water closet, including all fitting and fixtures, all as specified and and directed. Make: Hindware cat part no: 92522 (S-30), Cera cat part no: 3129, Bathsence cat part no:WH 97-P.

Concealed cistern with frame along with accessories, all as specified and directed. Make: Hindware cat part no: 518237 ,Parryware cat part no: E812599, Bathsense cat part no: BS-CC-B2

Chromium plated health faucet with 8mm dia, 1.2m long flexible tube and wall hook including all fitting and fixtures, all as specified and and directed. Make : Kohler cat part no: K-98100IN-0 , Jaquar cat part no: LD-573, Hindware cat part no: -F160059.

15mm Single Lever Basin Mixer , fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, fixed , complete all as specified and directed. Make: Hindware cat part no: F460009, Jaquar cat part no: OPP-15051BPM, Kohler cat part no: K-72288IN-4-CP.

Soap dispenser and holder with frosted glass bottle in polished chrome ,all as specified and directed. Make :Kohler cat part no: K-10712D-CP,Hindware cat part no:F860060, Jaquar cat part no: ACN-1137N.

Pillar tap "Flora type" of brass, chromium plated, screwed for 15mm bore pipe, complete all as specified and directed. Make: Kohler cat part no: 23483IN-4-CP, Aproyale cat part no: MASM401.

Single lever concealed diverter, upper part ,regular and high flow (push type), complete all as specified and directed. Make: Bathsense cat part no: MYDV111U, Hindware cat part no: F280042.

Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower, Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange , all as directed. Make: Jaquar cat part no: QQP-7281PM, Hindware cat part no: F120019, Prayag cat part no:-CAT No 8080.

Brass chromium plated towel ring , fixed in position with steel screws, all as specified and directed. MAKE : Prayag cat part no: BA-02, Parryware cat part no:T6904A1 , Hindware cat part no:F880007 .

Chromium plated soap dish in matt black, fixed to plugs with chromium plated brass screw, complete all as directed. Make :Kohler cat part no: K-25429IN-B or equivalent in parryware/hindware as approved.

Toilet paper holder, flat recessed type, stainless steel, complete all as specified and directed . Make: Prayag cat part no: BA -38, Hindware cat part no: F890002, Jacquar cat part no: ACN-1135N or equivalent in parryware/hindware as approved.

Chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixing to pipe and union complete, all as specified and directed

Chromium plated hand shower 100mm dia size with 1.50m flexible pipe, fixed to union, complete all as specified and directed

Chromium Plated bottle trap including all fitting and fixtures, all as specified and and directed. Make :Kohler cat part no;K-75823IN-BL or or equivalent in parryware/hindware as approved.

Peg hook set of 6 of aluminum body, complete all as specified and directed. Make: Prayag Cat part no :BEA-30 or equivalent in parryware/hindware as approved.

Square angle valve in polished chrome, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed complete all as specified and directed. Make: Parryware cat part no: T3907A1 or equivalent in parryware/hindware as approved.

PVC connections 15mm size with PTMT nuts of length 450mm, all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 900mm, all as specified and directed.

PVC SWR floor trap plain grating including jointing with solvent cement , of size 75mm dia, all as directed.

Counter top wash basin of size600 x600mm, including all fitting and fixtures, all as specified and and directed. Make:Kohler cat part no-K-76600IN-0, Hindware cat part no: -FONTE-91043

Table top wash basin of size 900 x 450mm, including all fitting and fixtures, all as specified and and directed. Make: Bath sence cat part no-TT-44X, Hindware cat part no: -RUBBIC 91041 , AproyeleTT-44-X / TT-34-X.

Brass chromium plated towel shelf, fixed in position with steel screws, complete all as specified and directed. Make: Kohler cat part no: K-17529T-CP or equivalent in parryware/hindware as approved.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings, framework of water tanks, framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc and similar work conforming to Fe.290.Gde-E-165, fixed in repairs, all as specified and directed.

Mild steel work as in iron post / posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-410-W (Gde.E-250)quality-A or Fe 290 (Gde -E-165) complete all as specified and directed.

Mild steel, plain, black sheet 1.60mm thick as in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required , all as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, n.exc 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide, complete all as specified and directed.

Plain cement concrete type B-1, 1:2:4 using (20 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed.

Reinforced cement concrete, 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete, all as specified and directed .

Reinforced cement concrete 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in beams, cantilevers , bressumers,lintels over 1.5m span, all as specified and directed .

Reinforced cement concrete 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in chajjas, parapets, facia etc, all as specified and directed .

Mild steel TMT bars 10mm dia and over ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Mild steel TMT bars 6mm to 8mm dia ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips as in stirrups, spacers and binders , all as specified.

Form work to flat surfaces of suspended slabs such as roof slab, floor slab, landing, shelves etc not exceeding 200mm thick, including edges in any position, rough finished surfaces, complete all as specified and directed.

Form work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to bater, fair finished surface of concrete flat, complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished flat surfaces of concrete, all as specified.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications , all as directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame , as per specification and as directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Mild steel screw bolt (machine made) with hexagonal at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal n.exc 5cm long, diameter of shank 5-10mm, complete all as specified and directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 , complete all as specified & directed by Engineer-in-Charge.

Rolled mild steel framed work as in doors or gates of angle or other section confiRunnung metreing to Fe 290 (Gde -E-165 ) with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, fittings and hanging, also fastening and fixing complete ,all as specified and directed by Engineer-in-charge.

Steel water tubes, 15mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed.

Steel water tubes, 20mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed.

16 mm outer dia CPVC pipes, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified.

20 mm outer dia CPVC pipes, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified.

Brass Elbow 16 mm for CPVC Pipe, all as directed.

Brass elbow 20 mm for CPVC Pipe, all as directed.

Brass Tee 16 mm dia UPVC pipe, all as directed.

Brass Tee 20 mm dia UPVC pipe, all as directed.

Male Brass Threaded Adaptor 16 mm dia (MTA/ MBTA) for CPVC pipe, all as directed.

Male Brass Threaded Adaptor 20 mm dia (MTA/ MBTA) for CPVC pipe, all as directed.

Female Brass Threaded 16 mm dia Adaptor (FTA/ FBTA) for CPVC Pipe, all as directed.

Female Brass Threaded 20 mm dia Adaptor (FTA/ FBTA) for CPVC Pipe, all as directed.

Male Brass Threaded Adaptor 50 mm dia (MTA/ MBTA) for CPVC pipe, all as directed.

PVC SWR pipes 110mm bore, single socketd in any length with rubber rings joints laid in trenches or in floors , complete all as directed.

PVC SWR pipes 75mm bore, single socketd in any length with rubber rings joints laid in trenches or in floors , complete all as directed.

PVC (SWR) branch pieces single socketed Y equal or unequal 110mm dia, complete all as directed.

PVC (SWR) bends any radius 110mm dia, complete all as directed.

PVC (SWR) bends any radius 75mm dia with oval acess door, complete all as directed.

PVC SWR vent cowl 110mm dia, complete all as directed.

PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement, complete all as directed.

500 Litres capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top) triple layered , hoisted and fixed in position including PTMT ball valve 20mm bore with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210gms and PTMT tank nipple, etc, complete all as specified and directed.

Gl frame work for seamless ceiling (Size of grid 605 x 605mm )comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed

Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately)

Making designer cornices of 100mm x 50mm with plater of paris of pattern as directed, complete all as directed.

Two coats of plastic emulsion including preparation of new ceiling surfaces complete all as specified and directed.

RCC pipe of class NP2, 150 mm dia bore with collars , ISI marked, jointed with cement mortar, laid in trenches and tested ,complete all as specified and directed.

Plain cement concrete, type C-2, 1:3:6, using 40mm graded crushed stone aggregate as in bed to drain pipes of 150 mm bore pipe including packing under pipes and tested () after the pipe are laid, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required for 150 mm dia of pipe,complete all as specified and as directed

Industrial homogenious vitrified heavy duty tile, premium 1st quality of size 300mm x 300mm x 10mm (any coloured as approved by Engr-in-Charge/GE ) over and including 15mm thick screed bed in CM 1:6 ,complete all as specified and directed. Make: Endura from Johnson or equivalent as approved.

Roughening surface of old concrete roof surfaces by picking, sweeping clean and washing down with water to remove old roof treatment , tiles ,dust etc including removal of debris, complete all as specified and directed.

Rendering 15mm thick (average thickness) plaster in cement mortar 1:4 on concrete roof surfaces for maintaining proper roof slope including flashings and junction of parapets etc , finishing the surface even and fair without using extra cement, all as specified and directed .

APP based polymeric membrane 3mm thick, minimum weight 3 kg/Square metre , reinforced with polyester non woven fabric (weight not less than 150 gms/Square metre) laid on primed surface by torch application on and including bituminous primer @ 0.40 ltrs per square metre by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, . The membrane shall be laid using butane torch and sealing all joints as per manufacturers instructions after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying one coat of bituminous aluminium paint @100gm/Square metre on top of membrane, complete all as specified and directed.

Factory made coloured chequered cement concrete tiles 250mm x 250mm x 22-25mm thick , set, jointed and pointed in neat cement slurry with grey cement and pigment to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete, all as specified and directed.

Supply only chain link fencing of 3.00 mm dia galvanized steel wire, size of mesh as approved complete all as specified and directed. Note : (i) Fixing included under item No 147 here-in-before. (ii) Unit weight (weight per sqm) of chain link fencing shall be measured at site, certified and signed by Engineer-in-Charge and Contractor in MB.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete all as specified and directed.

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Square metrem ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Square metrem ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit 20mm bore, terminated on and including new steel sunken boxes 1.2mm thickness covered with provision of 3mm thick plastic laminated sheet, comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch and fan regulator, complete all as specified and directed. Note :Unit rate is inclusive of cutting chases in wall /floor/PCC and making good the disturbed surfaces to match the original finishes surface and nothing extra shall be paid on this account.

All as per serial item 150 herein before but for socket outlet 3 pin 6 Amps on same board complete all as specified and directed

All as per serial item 150 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 150 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Square metrem (nominal area ) FRLSH cable & 2.5 Square metrem (nominal area ) cable as earth continuity conductor

Modular switch 1 way 6A, 1 module, complete all as directed

Modular switch 1 way 16A, 1 module, complete all as directed

Modular Socket, 6A - 2/3 pin combined 2 module, all as specified and directed

Modular Socket, 6/16A ,2/3 pin combined 2 module, all as specified and directed

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

MCB DB, with provision for incoming 2 pole (MCB / Isolator ) and single phase outgoing, suitable for surface and flush mounting, IP 43 protection, of metal 8 way double door, complete all as specified and directed.

MCB DB, with provision for incoming 2 pole (MCB / Isolator ) and single phase outgoing, suitable for surface and flush mounting, IP 43 protection, of metal 8 way double door, fixed in repairs, complete all as specified and directed.

MCB ,SPN, 240 volt, 40Amp, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs, complete all as specified and directed

MCB ,SPN, 240 volt, 40/63Amp, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs, fixed in repairs, complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs, complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs, fixed in repairs, complete all as specified and directed

Sheet metal enclosure for DB's , flush mounted suitable for 2 way SPN, fixed in repairs, complete all as specified and directed.

Indoor decorative extruded aluminium anodized housing /CRCA sheet steel coated housing LED batten type luminaries (LED batten shall be prewired box type) retrofit solution with and including replaceable retrofit cool day white LED tube rod with well designed aluminium heat sink /aluminium housing for excellent heat dissipation, 4 feet long, high efficiency electronic driver, system wattage not more than 20 watt with wall mounting arrangement and making connections with PVC insulated copper conductor 3 core cable of 0.5 sq mm, all as directed.

All as per Srl item no 166 but 2 feet long light, 10 watt capacity.

Recess mounted round LED down lighter 12 watt, white, complete all as specified and directed. Make: C&S cat part no: LTCR2XHPLED/W or equivalent in Phillips/Havells as approved.

Electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, all as specified and directed.

Steel water tubes, 15mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls, ceiling or laid in floors, for connection to geyser from tank including clamps etc, complete all as specified and directed.

PVC connections, heavy duty for hot and cold water, 450mm long and 15mm dia with CP brass nuts for geysers etc , complete all as specified.

Stop valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions, complete all as specified

Bib tap, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions, complete all as specified

Taking down of copper sub main wiring including existing battens/conduit etc, complete all as specified and directed.

Sub main wiring using two single core, PVC insulated and unsheathed FRLSH multi stranded copper conductor of size 4 Square metrem ( nominal area) 1100 volts grade with and including PVC pipe of 25mm dia size with cutting & chases in wall and making good for for PVC concealed conduit with and including continuous earth wire of size of 04 Square metrem PVC insulated and unsheathed FRLS multi stranded copper conductor 1100 volts grade, cable as earth wire and connected to main board ,complete all as specified and directed. Note : (i) Three runs each of one RM of 4 Square metrem cable shall be considered as 1 running metre for payment purposes.

Sub main wiring using two single core, PVC insulated and unsheathed FRLSH multi stranded copper conductor of size 6 Square metrem ( nominal area) 1100 volts grade with and including PVC pipe of 25mm dia size with cutting & chases in wall and making good for for PVC concealed conduit with and including continuous earth wire of size of 06 Square metrem PVC insulated and unsheathed FRLS multi stranded copper conductor 1100 volts grade, cable as earth wire and connected to main board ,complete all as specified and directed. Note : (i) Three runs each of one RM of 6 Square metrem cable shall be considered as 1 running metre for payment purposes.

Making opening of suitable size in existing brick wall for fixing of exhaust fan of 250mm sweep and making good the disturbed surface by plaster in CM (1:4) , complete all as directed by Engr-in Charge.

PVC exhaust fan of 250mm sweep , 230 V and 50 Hz, with louvers and shutter, all as specified and directed.

Premier Constructions

M/s Hari Om Engineer and Contractor

M/s R.K. CONSTRUCTIONS