GE ELECT/D-61/2025-26

Amount

Excavation in trenches not exceeding 1.5m wide & not exceeding 1.5m in depth and n.exc 10 sqm on plan for foundations, laying of LT under ground cables/ GI pipes and steel tubular poles etc. and getting out as in soft / loose soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm deep as in soil complete all as specified and directed by Engr-in-Charge

Removal of excavated material n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above in starting point complete all as specified and directed by Engr-in-Charge.

S & F common burnt bricks as mechanical protection of this cables using old size sub class ‘B’ bricks laid dry flat over the cable width equal to the length complete all as specified and directed by Engr-in-Charge

Material and labour for Sand filling in trenches for cushioning of UG cables as layers of 8 cm before laying and 15 cm after laying of cables complete all as specified and directed by Engr-in-Charge

Supplying and laying un-reinforced precast concrete cable cover, class HV, type 1, flat size 300mmx 180mm x 40mm for cable protection complete all as specified and directed by Engr-in-Charge.

All as per srl item No 6.00 here-in-before but using old cable cover obtained under srl item No 1 here in before complete all as specified and directed by Engr-in-Charge

Supplying, laying, jointing testing and connecting in replacement XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 11 KV grade, IS 7098 marked, suitable for HT 11 KV(E) system, laid in trenches / ducts / encased in GI pipe / fixed to pole, including jointing & testing complete all as specified and directed of following sizes as under complete all as specified and directed by Engr-in-Charge

95 Sqmm 3 Core

120 sqmm 3 core

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 70-120 Sqmm, 3 core complete all as specified and directed by Engr-in-Charge

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 70 -120 Sqmm, 3 core complete all as specified and directed by Engr-in-Charge.

Supply, laying, jointing, testing and commissioning in replacment of LT underground cables 1100 volts grade, PVC insulated XLPE and PVC sheathed, heavy duty armoured, with multistranded aluminium conductors, IS-1554 marked, laid in trenches complete all as specified and directed by Engr-in-Charge. Cables of the following sizes:- Note Excavation, earth work ,cable protection , sand fillings , cable joint shall be measured and paid separately.

10 Sqmm 4 Core

16 Sqmm 4 Core

25 Sq mm 3.5 core.

35 Sq mm 3.5 core.

50 Sq mm 3.5 core.

70 Sqmm 3.5 core

95 Sqmm 3.5 core

120 Sqmm 3.5 core

185 Sqmm 3.5 core

300 Sqmm 3.5 Core

Supply, fixing and testing straight through joint heat shrinkable type with jointing kit suitable for cable PVC/XLPE insulated armoured heavy duty aluminium conductor 1100 Volts grade complete all as specified and directed by Engr-in-Charge for the following sizes :-

25-50 Sqmm x 3.5 core/ 4 core

70-120 Sqmm x 3.5 core

185-240 Sqmm 3.5 core

300-400 Sqmm 3.5 core

Boring of hole under road/pavement/hard standing or any other situation by manual means and suitable for passing of GI pipe 50 to 100 mm bore and making good both ends complete all specified and directed by Engr-in-Charge.

S&F in replacement GI Pipe (light grade) with necessary accessories/ fittings for cable protections/pole for crossing of culverts/nallah complete all specified and directed by Engr-in-Charge of following bore sizes

Earthing complete in replacement with galvanized steel earth plate electrode of size 60cmx60cmx6 mm thick, buried directly in ground (earth pit not less than 3.5 m below normal ground level) with top edge of earth plate not less than 2.5m below normal ground level, connected to galvanized iron strip 32X6 mm by means of electric arc welding of galvanised iron or steel as shown in electrical plate No 3 of SSR Part I, connected to earth test point and the equipment on the other side complete all as specified, including testing and commissioning complete all specified and directed by Engr-in-Charge. Note : - (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe 40 mm bore GI pipe light grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth strip/GI earthing and protection pipe upto 7.5 meter beyond the earth plates electrode.

S&F in replacement KIOSK box wheather proof including made out of one piece mounted SMC base and door pole mounted hinged door size 333x233x120mm out side and 300x200x105mm inside dimensions comprising of aluminium bus bar 4 strips for 3 phase and neutral 63 Amps including embossing/painting of danger notice of size not less than 10cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body complete all specified and directed by Engr-in-Charge. Incluiding MS clamp of size 25x3 mm with suitable size nut,bolts & washer

Supply and fixig in replacement of LED Street light fittings of capacity 60 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Supply and fixig in replacement of LED Street light fittings of capacity 70 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Supply and fixig in replacement of LED Street light fittings of capacity 90 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Supply and fixig in replacement of LED Flood light fittings of capacity 100 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Supply and fixig in replacement of LED Flood light fittings of capacity 120 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Supply and fixig in replacement of LED Flood light fittings of capacity 200 Watt complete all as specified and directed by Engr-in-Charge. Make : Havells/Crompton Greaves/Syska

Taking down unsv LED Street light and supply & fixing energy saving and environmental friendly long life LED street light luminaries, 60 watt with min 100 Lumen per watt system efficacy inbuilt battery backup of min 2 hrs, made up of pressure die cast aluminium housing with high efficiency LED as Lighting source and Lens embedded PC cover having bottom opening separate driver compartment with IP 66 Protection and impact resistance of 1K 08 complete all as specified and directed by Engr-in-Charge, Make - Halonix Havells/Philips /Bajaj/ Orient /Crompton.

Supply, installing, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising complete all as specified and directed by Engr-in-Charge of the following :-

S&F of time switches astro type in having longitude and latitude of Indian cities in memory 415 V three phase 20 Amp rating with 20 Amps, 415 Volts, three pole contactor fitted inside factory made 2mm thick steel enclosure duly powder coated paint complete all as specified and directed by Engr-in-Charge

Supply, drawing, connecting & testing in replacement of 3 core, 2.5 Sqmm PVC insulated and PVC rounded sheathed, copper conductor (flexible) industrial cable 1100 Volts gradde conforming to IS-694 in steel tubular pole from KIOSK box to light fittings including providing suitable copper lugs complete all as specified and directed by Engr-in-Charge.

M&L for re-painting of LT Steel tubular poles of any sizes with apply of 2 coats of aluminium paint including rubbing with wire brush/emery paper & writing pole Nos in appropriate size of letters including making yellow and black strips upto height of 1.5 mtr above from ground level complete all as specified and directed by Engr-in-Charge.

M&L for re-painting of LT Panels/feeder pillars of approx size 2 to 4 Sqm with 2 coats of super enamal paint over a coat of red-oxide with sparygun including writing of feeder pillar numbers in appropriate size of letters as complete all as specified and directed by Engr-in-Charge

Material & Labour for painting of transformer installed on plinth/4/6 pole structures at various site of capacity 315 to 630 KVA with existing colour, with spraying machine, after cleaning, preparation of outer surface of transformer, including writing of SM No, MES and capacity of transformer complete all as specified and directed by Engr-in-Charge

Supplying and fixing in replacement MCCB 4 pole , 63 Amps, 16 KA ,50 Hz,415 Volts Complete all as specified and directed by Engr-in-Charge

Supplying and fixing in replacement MCCB 4 pole , 100 Amps,16 KA,50 Hz,415 Volts Complete all as specified and directed by Engr-in-Charge

Supplying and fixing in replacement MCCB 4 Pole ,125 Amps 16 KA Complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement MCCB 4 Pole ,160 Amps 25 KA Complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement MCCB 4 Pole ,200Amps 36 KA Complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement MCCB 4 Pole ,250Amps 36 KA Complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement MCCB 4 Pole ,400Amps 36 KA Complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement MCCB 4 Pole ,630Amps 50 KA Complete all as specified and directed by Engr-in-Charge.

S&F in renewal on load change over switch open execution of capacity 400 Amps , 4 pole , 415 volt , 50 Hz fixed in any type of existing LT panel/Feeder piller including taking out old existing unserviceable change over from panels etc complete all as specified and directed by Engr-in-Charge.

Testing the cables with high voltage DC testing machine and locating the fault in the cables by fault locating machine to pin point exact position of fault, disconnecting faulty 11 KV HT cables of different sizes from both ends, removal of Fault, Re-connections and testing of cables after removal of fault complete all as specified and directed by Engr-in-Charge. Note: (a) 11 KV HT cable & joints shall be measured and paid for seperately under respective items of schedule. (b) Retrieved old serviceable cable cover/bricks will be laid in trenches for cable protection. If extra PCC cover/bricks and sand required at site shall be measured and paid separately under respective items of BOQs. (c) Excavation and earth work will be measured and paid for seperately under respective items of schedule.

Testing the cables with high voltage DC testing machine and locating the fault in the cables by fault locating machine to pin point exact position of fault, disconnecting faulty 1100 Volt LT cables of different sizes from both ends, removal of Fault, Re-connections and testing of cables after removal of fault complete all as specified and directed by Engr-in-Charge Note: (a) 1100 Volt LT cable & joints shall be measured and paid for seperately under respective items of schedule. (b) Retrieved old serviceable cable cover/bricks will be laid in trenches for cable protection. If extra PCC cover/bricks and sand required at site shall be measured and paid separately under respective items of BOQs. (c) Excavation and earth work will be measured and paid for seperately under respective items of schedule.

Note : Contractor should procure and provide 50 % of the material as listed above within 15 days of the placing of work order and shall be verified by the Engr-in-charge.

ALLIED CONSTRUCTION (BID ID -3458584)

Commercial Traders (BID ID -3453512)

Ridhi engineers and builders (BID ID -3453595)

mayur enterprises (BID ID -3452639)

MV Engineers And Contractors (BID ID -3452648)