Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for RLBCAU Jhansi UP

Abstract of cost

S.No DESCRIPTION Amount as per DSR 2023 Non DSR amount

1 EARTH WORK 2892947.16

2 CEMENT CONCRETE WORK (CAST-IN-SITU) 4014770.74

3 REINFORCED CEMENT CONCRETE 26401233.72

5 FORM WORK 12143077.88

7 STEEL REINFORCEMENT 37757538.57

8 STRUCTURAL STEEL 22307400.00

9 MASONRY WORK 16950417.10

10 PLASTERING AND LINING WORK 4445393.23

11 INTERNAL AND EXTERNAL PAINTING WORK 3016517.13

12 CLADDING WORK 19158123.01

13 FLOORING WORK 17835777.24

14 INTERNAL AND EXTERNAL DOOR WORK 1705949.52

15 INTERNAL AND EXTERNAL FIRE DOOR WORK 3308438.33

16 STEEL/RAILING WORK 823647.97

17 ALUMINIUM AND EXTERNAL GLAZING WORK 2124528.15

18 FALSE CEILING WORK 3026331.62

19 MISCELLANEOUS WORKS 7596407.25

20 NON SCHEDULE ITEMS 54643013.00

Digitally signed by ANUJ

PROJECT : Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work

for RLBCAU Jhansi UP”.

BILL OF QUANTITIES FOR STRUCTURE WORK

S.N DSR Code- Rate DSR-

DESCRIPTION OF ITEM UNIT Quantity Amount

1.00 2.0 EARTH WORK

1.1 1 Carriage of material

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),

including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including

1.1.1 2.8 dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated

soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a

1.3 2.25(a) lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in 807.500 565653.75

trenches, plinth, sides of foundation etc. complete.

Clearing Jungle including uprooting of rank vegetation , grass, wood ,bruch ,trees and sapling of

2.31 grith up to 30cm measured at a height of 1 meter above ground level and removal of rubbish Sqm 486.795 17.60 8567.59

up to a distance of 30m outside the periphery of area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/

2.34.1 Lindane emulsifiable concentrate of 20% litre 200.000 234.75 46950.00

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

1.4 2.35 anti-termite treatment (excluding the cost of chemical emulsion) :

With Chlorpyriphos/ Lindane E.C. 20% with 1%

With Chlorpyriphos/ Lindane E.C. 20% with 1%

Sub total 2892947.16

2.0 4.0 CEMENT CONCRETE WORK (CAST-IN-SITU)

Providing and laying in position cement concrete of specified grade excluding the cost of

2.1 4.1 centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size)

Digitally signed by ANUJ

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand ( zone-

III) derived from natural sources: 6 graded stone aggregate 20mm nominal size derived from

natural sources) over 75mm thick bed of dry brick ballast 40mm nominal size. well rammed and

consolidated and grouted with fine sand, including necessary excavation, levelling & dressing &

finishing the top smooth.

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources :3 graded

4.5.1 stone aggregrate 20mm nominal size derived from natural sources) cum 139.500 10105.10 1409661.45

Sub total 4014770.74

3.0 5.0 REINFORCED CEMENT CONCRETE

DESIGN MIX CONCRETE

Reinforced cement concrete work in beam , suspended floors , roofs having slope up to 15

landing , balconies , shelves , chajjas , lintels , bands, plain window sills , staircases and spiral

5.3 stair cases above plinth level up to floor five level, excluding the cost of centering , shuttering , cum 91.243 11505.50 1049801.66

finishing and reinforcements with 1:1:5:3 (1 Cement :1.5 coarse sand (zone -III) derived from

natural sources :3 graded stone aggregate 20mm nominal size derivd from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

3.1 5.33 laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be

payable separately. In case the cement content in design mix is more than 110% of the

specified minimum cement content, the contractor shall have discretion to either re-design the

mix or bear the cost of extra cement.

3.1.1 5.33.1 All works upto plinth level

5.33.1.2 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 440.000 9504.75 4182090.00

3.1.2 5.33.1 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 2146.905 9860.40 21169342.06

Sub total 26401233.72

3.3.1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for:

3.3.2 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 701.250 392.15 274995.19

3.2.3 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 6654.855 927.25 6170714.30

3.2.4 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 2970.000 736.40 2187108.00

3.2.5 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 3395.796 961.30 3264378.69

3.2.6 5.9.7 Stairs, (excluding landings) except spiral-staircases Sqm 321.435 764.95 245881.70

Sub total 12143077.88

3.3 5.0 STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including straightening, cutting,

3.3.1 5.22' bending, placing in position and binding all complete upto plinth level.

3.3.1. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Digitally signed by ANUJ

Steel reinforcement for R.C.C. work including straightening, cutting,

3.3.2 5.22A bending, placing in position and binding all complete above plinth level.

3.3.2. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforced cement concrete work in arches , archribes , domes , vaults , shells, folded plate and

roofs having slope more than 15 up to floor five level, excluding the cost of centering , shutering

5.5 , finishing and reinforcement with 1:1:5:3 ( 1 cement : 1.5 coarse sand (zone -III) derived from cum 10.000 12205.85 122058.50

natural sources :3 graded stone aggregate 20mm nominal size derived from natural sources)

5.9.10 Extra for arches , domes vaults exceeding 6m span sqm 10.000 608.15 6081.50

5.11.1 Suspended floors , roofs , landings, beams and balconies (plan area to be measured) sqm 433.925 384.30 166757.38

Sub total 37757538.57

4.0 10.0 STRUCTURAL STEEL

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and applying a priming coat of approved steel

4.1 10.16 primer, including welding and bolted with special shaped washers etc. complete.

4.1.1 10.16.1 Hot finished welded type tubes Kg 114750.000 194.40 22307400.00

Sub total 22307400.00

Total of scheduled items 105516968.07

Digitally signed by ANUJ

Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for RLBCAU Jhansi UP”.

Description of Indicative Items

DSR Code- Rate DSR- Amount as per DSR

S.No. Unit Qty

1 MASONRY WORK

Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonry with 150 mm to 300

mm thick with grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3)

in super structure above plinth level up to floor V level with RCC band at sill level and lintel level

with approved block laying polymer modified adhesive mortar all complete as per direction of

Engineer-in-charge. (The payment of RCC band and reinforcement shall be made for

Brick work with common burnt clay F.P.S (non-modular) bricks of class designation 7.5 in

1.2 6.1 foundation and plinth in

6.1.2 Cement mortar 1:6 (1 Cement : 6 coarse sand) Cum 88.434 7132.25 630,733.40

Providing and placing in position 2 Nos. 6 mm dia M.S. bars at every third course of half Block

1.4 6.4.2 Cement Moar 1:6 (1 Cement : 6 coarse sand) Cum 152.268 9105.95 1,386,542.29

Sub Total 16,950,417.10

2 PLASTERING AND LINING WORK

2.1 13.16 6 mm cement plaster of mix : -

2.2 13.1 12 mm cement plaster of mix : -

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement :5

2.3 13.12 coarse sand ) and a top layer 6mm thick cement plaster 1:3 (1 cement :3 coarse sand ) finished

rough with sponge Sqm 2,592.285 537.45 1,393,223.57

Extra for providing and mixing water proofing material in cement plaster work in proportion per bag of 50 kg

recommended by the manufacturers.

Sub Total 4,445,393.23

3 INTERNAL & EXTERNAL PAINTING

3.1 13.37 White washing with lime to give an even shade : -

3.1.1 13.37.1 New work (three or more coats) Sqm 152.823 39.05 5,967.73

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50

3.2 13.41 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve

even shade and colour: -

New work (two or more coats) over and including water thinnable priming coat with cement

primer having VOC content less than 50 gram/litre 185.65

Digitally signed by1 ANUJ

3.3 13.45 Finishing walls with textured exterior paint of required shade : -

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @ 2.20kg/10 sqm 223.6

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per

3.4 13.52 manufacturer's specifications including appropriate priming coat, preparation of surface, etc.

complete. Sqm -

Cutting holes of required size in brick masonry wall for fixing of exhaust fan

3.5 14.81 including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the

same etc. complete as per direction of Engineer-in-charge. Each 10.000 288.10 2,881.00

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre of approved brand and manufacture, including

applying additional coats wherever required to achieve even shade and colour

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less

3.7 13.61 than 150 grams/ litre, of approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour. Sqm -

3.7.1 13.61.1 Two or more coats on new work Sqm 470.694 155.9 73,381.24

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete 262.7

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above

floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced

with rabbit wire mesh fixed to wooden frame (frame work to be paid separately):

Sub Total 3,016,517.13

4 CLADDING WORK

Providing and fixing dry cladding upto 10 meter height with 30 mm thick gang saw cut stone with

machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work

and/or with the help of cramps, pins etc. And sealing the joints with approved weather sealant as

per architectural drawing and direction of Engineer-in-charge. (The steel framework, stainless

steel cramps and pins, etc shall be paid for separately).

8.20.1 Red sand stone- 30 mm thick gang saw cut stone Sqm 181.475 2,902.65 526,758.41

8.20.2 White sand stone- 30 mm thick gang saw cut stone Sqm 2,167.500 3,040.10 6,589,416.75

Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level

for every additional height of 3 m or part there of. 165.85

Digitally signed by2 ANUJ

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with

machine cut edges granite stone) on walls at all heights using M.S. square/ rectangular tube in

the required pattern as per architectural drawing, including cost of cutting, bending, welding etc.

The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats

etc. which shall be welded to the frame and embedded in brick wall with cement concrete block

1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size

300x230x300 mm, including cost of necessary centring and shuttering and with approved

expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved

cramps/ pins etc. shall be welded to the frame ork to support stone cladding, the steel work will

be given a priming coat of Zinc primer as approved by Engineerin- charge and painted with two

or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the

Engineer-in-charge for approval before execution). The frame work shall be fixed in true

horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the

purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall

Providing and fixing adjustable stainless steel cramps of approved quality of required shape and

size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms),

for dry stone cladding fixed on framework at suitable location, including making necessary

recesses in stone slab, drilling required holes etc. complete as per direction of the Engineer-in-

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4

(1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss

finish etc. complete at all levels.

4.5.1 8.2.2 Granite stone slab of colour black, Cherry/ Ruby red

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen

platform, vanity counters and similar location in marble / stone work including necessary holes

for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing machine cut, mirror/ eggshell polished , stone work for wall lining (veneer

work) including dado, skirting, risers of steps etc., in required design and pattern wherever

required, stones of different finished surface texture, on 12 mm (average) thick cement mortar

4.7 8.11 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including

pointing with white cement slurry admixed with pigment of matching shade, including rubbing,

curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-

18 mm thick Italian Marble stone slab, perlato, Rosso verona, Fire red or dark emperadore etc.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to

be specified by the manufacturer ) of approved make in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing

with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment

of matching shade complete. Sqm 522.158 1267.95 662,070.74

Digitally signed by3 ANUJ

Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse

sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an

admixture of pigment, matching the stone shade, jali slab without any chamfers etc

Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in

Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2

(1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.

Sub Total 19,158,123.01

5 FLOORING WORK

Providing and laying flamed finish Granite stone flooring in required design and patterns, in

linear as well as curvilinear portions of the building all complete as per the architectural drawings

with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement :

5.1 11.55 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed

with pigment of matching shade including rubbing, curing and polishing etc. all complete as

specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as

well as curvilinear portions of the building, all complete as per the architectural drawings, with

stone slab of Specified thickness over 20 mm (average) thick base of cement mortar 1:4 (1

5.2 11.56 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement

5.3 11.26 slurry mixed with pigment to match the shade of the slab, including rubbing and polishing

complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine

5.4 8.3 polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-

Providing and fixing cramps of required size & shape in RCC/ CC / Brick masonry backing with

5.5 8.7 cement mortar 1:2 ( 1 cement :2 coarse sand), including drilling necessary hole in stones and

embedding the cramp in the hole (fastener to be paid separately).

5.5.1 8.7.2 Stainless steel cramps Kg 42.500 714.4 30,362.00

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing

including drilling necessary holes and the cost of bolt etc complete.

5.6.1 8.8.1 Wedge expansion type

5.6.1.1 8.8.1.1 Fastener with threaded dia 6 mm Each 127.500 36.75 4,685.63

Digitally signed by4 ANUJ

Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering- All work up to plinth level:

1:2:4 ( 1cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources) 7878.5

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18 mm

thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

5.8 11.51 sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white

cement slurry admixed with pigment to match the marble shade including rubbing, curing and

polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

18mm thick Italian marble stone slab, Perlato, Rosso verona, Fire red or dark emperadore etc

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the

manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved

brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with ement based

high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average

6 mm thickness, including grouting of joints (Payment for grouting of joints to be made

separately). -

5.10 11.24 Pre finished nosing to treads of steps of Marble/Granite stone. Mtr 340.000 719.9 244,766.00

Grouting the joints of flooring/Walls tiles having joints of 3 mm width to 10mm width, using epoxy

grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of

resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant.

The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum

dewatering process and finally finished by floating, brooming with wire brush

etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering

work shall be paid for separately). (Note:- Cement content considered in this item is @ 330

kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Sub Total 17,835,777.24

6 INTERNAL & EXTERNAL DOORS

Providing wood work in frames of doors, windows, clerestory windows and other frames,

6.1 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia &

length ( hold fast lugs or dash fastener shall be paid for separately). -

6.1.1 9.1.1 Second class teak wood Cum 3.059 142949.7 437,283.13

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative

type, core of block board construction with frame of 1st class hard wood and well matched teak

3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

6.2.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 110.976 3473.85 385,513.98

Digitally signed by5 ANUJ

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges

of flush door shutters (over all area of door shutter to be measured). 462.35

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI

marked flush door shutters conforming to IS: 2202 (Part I)

Providing and fixing wooden moulded beading to door and window frames

6.5 9.40 with iron screws, plugs and priming coat on unexposed surface etc.

6.5.1 9.40.1 Second class teak wood

6.6 13.114 Melamine polishing on wood work (one or more coat). Sqm 240.176 1192.3 286,361.84

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/

suede finish with high density protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing bright finished brass tower bolts (barrel type) with

necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock

6.9 9.76 with 6 levers and a pair of lever handles of approved quality with necessary

screws etc. complete. each 17.000 854.65 14,529.05

Providing and fixing bright finished brass 100 mm mortice latch with one

6.10 9.77 dead bolt and a pair of lever handles of approved quality with necessary

screws etc. complete. each 44.200 726.6 32,115.72

Providing and fixing bright finished brass hanging type floor door stopper

with necessary screws, etc. complete. 121.65

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10

mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising

of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry,

etc. as per direction of Engineer-in-charge. -

Sub Total 1,705,949.52

7 INTERNAL & EXTERNAL FIRE DOORS

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60

mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not

less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame

shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a

provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size

7.1 9.161 M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball

Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be

finished with a approved fire resistant primer or Powder coating of not less than 30 micron in

desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is

Digitally signed by6 ANUJ

Providing and fixing 80 mm thick glazed fire resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634- 1:1999, tested and certified as per laboratory

approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of

1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation

to achieve desired acoustic level of 38 db STC having density min 96 kg/m³ and fixing with

necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including

applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc

all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x

33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm

c/c , including applying a coat of approved fire resistant primer/powder coating of not less than

30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect

as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge wit glass

of required thickness having 120 minutes of fire resistance both integrity and radiation control

(EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test

report/clarification of fire glass and the glass should have the stamp showing the value of E, EW

and EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation

body which operates in accordance with ISO/IEC 17011 and accredited labs as per ISO/IEC

17025 for testing and calibration scopes shall be eligible. The maximum galzing size shall not be

more than 1100x2200 mm (w x h) or 2.42 sqm.

providing and fixing panic bar/ Latch (double point) fitted with a single body trim latch and lock in

7.4 9.139 back side of the panic latch of reputed brand and manufacture to be approved by engineer in

charge, all complete Each 30.600 8366.15 256,004.19

Sub Total 3,308,438.33

8 STEEL/ RAILING WORK

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with

necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required

size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of

Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Sub Total 823,647.97

9 ALUMINIUM WORK AND STRUCTURAL GLAZING

Digitally signed by7 ANUJ

Providing and fixing double action hydraulic floor spring of approved brand and manufacture

conforming to IS : 6315, having brand logo embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding

in floors as required and making good the same matching to the existing floor finishing and

cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete

as per the direction of Engineer-in-charge.

9.1.1 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness Each 22.100 2823.85 62,407.09

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5

or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to

AAMA 2604 of required colour and shade as approved by the Engineer-in-charge. (The item

includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of

extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of

aluminium extruded section shall be taken for purpose of payment.

Design , fabrication , testing , protection , installing and fixing in position semi (grid) initized

system of structural glazing (with open joints () for linear as well as curvilinear portions of the

builing for all heights and all levels including:(a) structural analysis &design and preparation of

shop drawings for the specified design loads conforming to IS 875 part III (the system must

passed the proof test at 1.5 times design wind pressure without any failure), including functional

design of the aliminium sections for fixing glazing panels of various thickness, aluminium cleats,

sleeves and splice plates etc. gaskets , screws, toggles, nuts , bolts, clamps etc, structural

weather silicone sealants , flashings , fire stop (barrier) cum smoke seals , microwave cured

EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire

hazard including: (b) Fabrication and suppling serrated MS hot dip galvanised / Aluminium alloy

of 6005 t5 brackets of required sizes , sections and profiles etc. to accommodate 3 dimentional

movement for achieving prefect verticality and fixing structural glazing system rigidly to thew

RCC/ masonry / structural steel framework of building structure using stainless steel anchor

fasteners / bolts , nylon speretor to prevent bimetallic contacts with nuts and washers etc. of

stainless steel grade 316 , of the required capacity and in required numbers. (c) Providing and

filling , two part pump filled , structural silicone sealant and one part weather silicone sealant

compatible with the structural silicone sealant of required bite size in a clean and controlled

factory/ work shop environment , including double grade , brand and backer rod , all of approved

grade, brand and manufacture , as per the approval sealant design, within and all around the

perimeter for holding glass. (d) providing and fixing in position flashings of solid aluminium sheet

1mm thick and of sizes , shapes and profiles as required as per the site conditons, to seal the

gap between the building structure and all its interfaces with curtain glazing to make it waterlight.

(e) Making provision for drainage of mositure / water that enters the curtain glazing system to

make it watertight by incorporating principles of pressure equalization , providing suitable gutter

profiles at bottom (if required), making necessary holes oif reuired sizes and of required

numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating

and installation of aluminium grid , installation of glazed units , T&P scaffolding and other

incidental charges includingwastages etc,. enabling temporary structures and services , cranes

or cradles etc. as decribed above and as specified The item includes the cost of getting all the Sqm 132.600 3510.5 465,492.30

Digitally signed by8 ANUJ

structural and functional design

including shop drawings checked by a structural designer , dullyapproved by engineer-in-

charge. The item also includes the cost of all. mock ups ups at site , cost of all samples of the

9.3 25.2 individual components for testing in an approved laboratory , feild tests on the assembled

working structural glazing as specified , cleaninf and protection till the handing over of the

building for occupation. In the end, the contractor shall provide a watertight structural glazing

having all the performance characteristics etc. all complete as required as per the approved

shop drawings and as directed by the engineers- in charge NOTE -1 The cost of providing

extruded aluminium frames , shadow boxes , extruded aluminium section capping for fixing in

the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for

separately under relevant items under this sub- head . However, for the purpose of pavement ,

only the actual area of sturctural glazing ( includng width of grooves ) on the external face shall

be measured in sqm. up to two dicimal places NOTE -2 The following perfornamce test are to be

conducted on structural glazing exceeds 2500 sqm from the certified laboratories accreditated

by NABL , department of science & technologies , india. cost of testing is payable separately.

The NIT approving will decide the necessity of testing on the basis of cost of the work, cost of

the test and importance of the work. performance Testing of structural glazing system tests to be

conducted in the NABL accredited lab or any other accreditation body which operates in

accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC17025. 1- Performace

Laboratory Test for Air Leakage Test (-50pa to 300pa) & (+50pa to +300pa) as per ASTM E-283-

04 testing method for a range of testing limit 1 to 200 mVhr. 2- Atatic water penetration test

(50pa to 1500pa) as per ASTME -331-09 TESTING METHOD FOR A range upto 2000ml. 3 -

Dynamic water penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range

upto 2000ml. 4 - Structural performance Deflection and deformation by static air pressure test

(1.5 times design wind pressure without any failure ) as per ASTME-330-10 testing method for a

range upto 50mm 5- Sesmic movement test (upto30mm) as per AAMA501.4 testing method for

qualitative test , Test to be conducted on site. 6 - on site test for water leakage for a pressure

range 50kpa to 240kpa (35psi) upto 2000ml.

Digitally signed by9 ANUJ

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-

sealed 6-12-6 mm insulated glass (double glazed) vision panel units of size and shape as

required and specified, comprising of an outer high performance heat strengthened float glass

6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved

colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm

wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all

complete for the required performances, as per the Architectural drawings, as per the approved

9.4 25.3 shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be

assembled in the factory/ workshop of the glass processor. (i) Coloured tinted float glass 6mm

thick substrate with reflective soft coating on face # 2, + 12mm Air gap + 6mm Heat

Strengthened clear Glass of approved make having properties as visible Light transmittance

(VLT) of greater than or equal to 49%, Light reflection internal not greater than 11%, light

reflection external not greater than 10 %, shading coefficient (0.38- 0.42) and U value of 1.5 to

1.8 W/m2 degree K etc.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying

at site all accessories and hardwares for the openable panels as specified and of the approved

make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with

9.5 25.4 stainless steel plates, handles, buffers etc. including necessary stainless steel screws/

fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed by the Engineer-in- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened

monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of

approved colour and shade so as to match the colour and shade of the IGUs in the vision panels

etc. ,all complete for the required performances as specified, as per the Architectural drawings,

as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge.

9.6 25.6 For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the

area of grooves and weather silicone sealant) provided and fixed in position, shall be measured

in sqm.(Payment for aluminium work desigining of curtain wall and shadow box shall be paid in

relevent Item).

Providing and fixing 12 mm thick frameless toughned glass door shutter of approved brand and

manufacture, including providing and fixing top and bottom pivot and double acting hydraulic

9.7 21.18 floor spring type fixing arrangement and making necessary holes etc. for fixing required door

fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.

to be paid separately). Sqm 93.500 5325.9 497,971.65

Sub Total 2,124,528.15

10 FALSE CEILING

Digitally signed 10 ANUJ

Providing and fixing false ceiling at all heights including providing and fixing of frame work made

of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120gms

/ sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x

1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to

the ceiling with dash fastener 12.5 mm dia * 50 mm long with 6 mm dia bolts, other flange of

cleat fixed to the angle hangers of 25 * 10 * 0.5 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels 45 * 15 * 0.9

mm running at the spacing 1200 mm centre to centre, to which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with

connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every Junction, including

fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with

25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, including jointing and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound, jointing tapes, finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all

complete as per drawings, specification and direction of the Engineer in Charge but excluding

the cost of painting with:

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 (Part I) :2011 (Board

with BIS certification marks) Sqm 2,054.280 1355.8 2,785,192.82

Providing and fixing tiled false ceiling of specified materials of size 595 * 595 mm in true

horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections

(galvanized @ 120 grams/sqm, both side inclusive) consisting of main "T" runner with suitably

spaced joints to get required length and of size 24 * 38 mm made from 0.30 mm thick

(minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24 * 25 mm made

of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center

to center to form a grid of 1200 * 600 mm and secondary cross "T" of length 600 mm and size

24 * 25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 *

600 mm panel to form grids of 600x600 mm and wall angle of size 24 * 24 * 0.3 mm and laying

false ceiling tiles of approved texture in the grid including, required cutting/making, opening for

services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be

suspended from ceiling using GI slotted cleats of size 27 x 37 * 25 * 1.6 mm fixed to ceiling with

12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly

level clips of size 85 * 30 * 0.8mm spaced at 1200 mm center to center along main T, bottom

exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete

for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI metal ceiling lay in perforated Tegular edge globle white colour tiles of size 595 x1200mm

and 0.5mm thick with 8mm drop,made of GI sheet having gavanizing of 100gms/sqm(both sides

inclusive)and 20% perforation area with 1.80mm dia holes and having NRC Noice Reduction Co-

efficient) of 0.5, electro statically polyster powder coated of thickness 60 microns (Minimum),

including factory painted after bending and perforation and backed with a black glass fiber

acoustical fleece. Sqm 17.000 2068.75 35,168.75

Digitally signed 11 ANUJ

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch,

including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen

washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be

manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in

resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation

and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall

be opaque or translucent, clear or pigmented, textured or smooth as specified.

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum

plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white

0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the

back side with all edges sealed with the face side PVC film which goes around and wraps the

edges and is bonded to the edges and the back side metalized polyester film so as to make the

tile a completely sealed unit. Sqm 17.000 2215.15 37,657.55

12.5 mm thick fully perforated gypsum board tile made from plasterboard having glass fibre

conforming to IS:2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm

10.5 12.52.4 c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue

on the back sode, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin

bonded glass wool backing. Sqm 102.000 1528 155,856.00

Sub Total 3,026,331.62

11 MISCELLANEOUS WORKS

Providing and laying integral cement based water proofing treatment including preparation of

11.1 22.7 surface as required for treatment of roofs, balconies, terraces etc. Consisting of following

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound comforming to IS. 2645 and approved by engineer-in-charge over the RCC slab

including adjoining walls upto 300 mm height including cleaning the surface before treatment.

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement

11.1.2 b mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming

to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the

adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying second coat of cement slurry using 2.75 kg/sqm of

11.1.3 c cement admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse

sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-

11.1.4 d in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally

finishing the surface with trowel with neat cedment slurry and making pattern of 300x300 mm

square 3 mm deep

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

11.1.5 curing and for final test.

Digitally signed 12 ANUJ

11.1.6 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm Sqm 1,451.800 1684.6 2,445,702.28

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1

11.2 12.22 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a

coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade

made by block making machine with strong vibratory compaction and of approved size and design/ shape

11.3.1 16.68 laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling

the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller

including making good the undulations etc. and re-rolling the sub grade and disposal of surplus eartwith

lead upto 50 metres. sqm 3,417.850 218.9 748,167.37

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to

wet mix macadam (WMM) specification including premixing the material with water at OMC in for all

leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well

prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired

density, complete as per specifications and directions of Engineer-in-Charge.

Sub Total 7,596,407.25

Total of schedule items 79,991,530.55

NON SCHEDULE ITEMS

S.No. NSI Code Description of Indicative Items Unit Qty Rate - NS Amount as per NS

Providing & laying texture paint (Finished thickness 2.5 mm to 3.00 mm ) with natural stone

crushed powder mixed with pigmentation (0.01 % -3.00%) applied over plaster surface within

grooves. Acrylic primer added with wall sealer to be over the surface for better adhesion of the

texture with surface. 1st- coat without chips to be applied as base coat which gives added

strength to the final product, to be applied with stainless steel trowel. Texture coat to be applied

12 NSI 1 with chips of stone powder having available natural stone base shade with stainless steel trowel

finished with acrylic trowel, final coat of siloxine water base protection coat to be applied which

make the product completely water repellent / dust resistant / anti fungal which ensures with a

warranty of 08 years on shades and sustainability ,whereas grooves are to be crafted in plaster

as design approved by engineering in charge.

Digitally signed 13 ANUJ

Providing & fixing in position necessary Glass 12 mm Glass Door with Fittings(Floor spring of ss

304 grade of 90 kg weight capacity ,Top Patch - Variable pivot point of 55 or 65mm -With SS

304 cover-,Bottom Patch- Variable pivot point of 55 or 65mm- With SS 304 cover ,11-

Type Pull Handle 325 back to back fixing for glass, wood and metal doors in satin stainless

13 NSI 2 steel.Length =325mm, 25mm dia, -Finish-SSS, 304 Grade; Center to Center - 300mm x 12mm

Hole Dia, Corner Patch Lock with Strike Plate- With Euro profile cylinder and strike plate -Dead

projection of 15mm (single throw)- With SS 304 cover -Finish: SS,. The work shall be carried out

as per specifications, drawings and as per directions of the engineer-in-charge. (fittings shall be

as per list of make of material ) sqm 85.000 11348.00 964,580.00

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both

14 NSI 3 having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension with

8mm clear toughend glassof reputed make (for all area.). Sqm 343.060 11311.00 3,880,352.00

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm

both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of

NSI 3.1 appropriate dimension ,with 6mm clear toughend glass of reputed make(Area of window above

1.75 sqm upto 2.50 sqm)

Providing and applying High performance top coat sealer of approved make (as per drawing or

as directed by project incharge) on the exposed surface on stone cladding to form invisible

15 NSI 4 barrier by allowing vapour to escape for resistance against water alklies, acid staining and freeze

thaw damages. The sealer should be applied at the rate of 2 ltr per 285 sqft of surface area

complete as per direction of Engineer in Charge. Sqm 2,773.975 206.00 571,439.00

Providing and fixing machine cut, table rubbed pre-polished Granite stone in skirting, risers of

steps and dado etc. in required design and patterns wherever required, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm

thick granite stone slab of different finished surface texture, on 12 mm (average) thick cement

16 NSI 5 mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with cement slurry @ 3.3 kg/sqm

including pointing with white cement slurry admixed with pigment of matching shade including

rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-

Charge : Colour Jet Black, Cherry/Ruby Red, Cat eye or equivalent

Stone work for wall lining beyond 10 m height with grooves and special adhesive over 12 mm

thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement

with an admixture of pigment to match the stone shade. Including all steel fastener, cramp stc.

complete in all respect as per direction of engineer-in-charge -

NSI 6.1 18mm thick Granite stone (mirror polished and machine cut edge) Sqm 221.000 4111.00 908,531.00

Providing and fixing 18 mm thick gang saw cut Italian Marble stone(black splash), mirror

polished, premoulded and prepolished, machine cut for toilet vanity counters, window sills ,

facias and similar locations of required size, approved shade, colour and texture laid over 20 mm

18 NSI 7 thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at all levels.

19 NSI 8 Extra over 25mm thick granite (outdoor deck / terrace areas)instead of 18 mm Sqm 379.627 498.00 189,054.00

20 NSI 9 Extra for sand blasting/ short blasting/ lappato finish on granite stone Sqm 204.000 212.00 43,248.00

Providing and making anti skid grooves in granite treads 3 nos @ 2 cm c/c of required size as

per drawing including proper finishing. ( length of treads to be measured ).

NSI 10.1 15 mm wide and 10 mm deep groove Rm 680.000 345.00 234,600.00

Digitally signed 14 ANUJ

Providing and fixing of tufted cut pile carpet having Carpet Type Contract Carpet, Intendent Use

Heavy Traffic, Production Process Tufted and Printed, Gauge 1 / 10 Inch, Cut Pile, Pile Material

% 100 Polyamide 6 (nylon), Pile Height 5.5 mm (finish, +/- %5), Total Height with (Felt Back) 8.2

mm (finish, +/- %5), Stitches Per 10 cm 48 stitches / 10cm ( +/- %5), Tufts Per sqm 188,640

tufts / sqm (+/- %5), Pile Weight 1.000 gr / sqm (+/- %5), Total Weight with (Felt Back) 2.220

22 NSI 11 gr/sqm (+/- %5), Primary Backing Woven Polypropylene, Secondary Backing 240 gr/sqm Felt

Back, Finish Width 4.00 m and/or Runner Size (± 1 cm), Acoustic insulation from noise impact

17 dB, Reaction to fire B fl -S1 conforming to EN 14041:2004, EN 14041:2004/AC:2006, Level

of use classification class 33, Comfort Class LC4, Castor chair suitability Suitable for intensive

use, Staire suitability Suitable for intensive use, Electric behavior according to EN 14041

STAGE FLOORING: Providing material for 65x16 (made from raw wood size 75 x 20mm) thick

Teak wood planks flooring with Tongue and Groove joints (concealed screwing) over 50x50mm

section wood framing @ 600mm c/c in both directions with 12mm thick commercial ply.

The Frame work should be leveled and duly fixed with base floor using MS cleats and neoprene

rubber pads.The framing to be filled with 50mm thickness rockwool or fibre glass resin bonded

insulation of density 48kg/cum.

Melamine polishing of teakwood on exposed surface: In horizontal/vertical plane (Rate for

flooring shall include providing additional framework required for housing microphone and power

outlet junction boxes including providing and fixing hinged 15mm thick teakwood cover for the

junction boxes. Complete the work in all respect including polish as per direction of engineer in

Supply and installation of 12MM BOX UP series cubicles of width and depth as per

specifications/ site drawings.

DESCRIPTIONMade from solid grade compact high pressure laminate as per IS:2046

manufactured under high specific pressure > 5 MPa and temperature >120oC with bunch of kraft

papers impregnated with thermosetting phenolic resin and decorative papers made of cellulose

24 NSI 13 fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion,

heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels

have a black core that when machined, presents a distinctive black edge. Panel thickness min

12 mm. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per

drawing. Complete the work in all respect including all accessories and fittings as per direction of

engineer in charge Each 25.000 39244.00 981,100.00

Supply and fixing of fire rated SS Ball Bearing Hinges of size 100mm x 89mm and 3.0mm

25 NSI 14 thickness SS 304 Grade complete with SS Screws of approved make. ( minimum 4 Nos per

Supply and installation of fire rated Heavy Duty door closers of approved make tested in

26 NSI 15 accordance with BS: 476 Part – 22: 1987, all complete as per manufacturer's specifications.

Digitally signed 15 ANUJ

Torsion Spring U-Baffle (50mm x 150mm) False Ceiling System in 150mm moduleProviding and

fixing U Baffle Aluminium panel ceiling manufactured of wooden finish /solid colour consisting of

panel size 50 mm width X 150 mm deep using 0.6 mm thick, panel length upto 4 mtr, Coil

Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion

resistance Aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming

characteristics. Torsion Spring panel with two side legs die formed and two end legs die formed

and punched to receive torsion springs (min two springs each end or side) for secure

engagement into Tee Grid main runners which are factory punched to receive torsion springs.

Planks will be square edged. The metal ceiling panels shall be downward accessible with a

minimum of four (4) torsion springs per panel. The Plank shall be Polyester powder coated in

Wooden Finish.Main Runners: 24mm deep, inverted “Tee” sections, 3m long, with factory

punched flanges to receive torsion spring assembly. Main Tee on center spacing to match panel

27 NSI 16 length.Cross Runners: 24 mm deep, inverted “Tee” sections designed to interlock in to web of

main tee section on designated spacing. Cross tee length to match panel length. Cross tees are

spaced spacing 1200mm on center maximum.Suspension System: Panel grid system shall be

suspended by means of threaded rod at a distance of 1.8 mtr c/c. (Actual distance of threaded

rod/carrier to be calculated based on the actual drawing). As per manufacturer standard

considering type of plenum and its height.PAINT FINISH: Aluminium panels shall be

chromatised for maximum bond between metal and paint enamelled twice under high

temperature, Exposed side with a full primer and finish coat on a Continuous Paint Line.MODE

OF MEASUREMENTS: Measurements shall be wall to wall without any deductions for lights,

diffuses, columns. Complete the work in all respect including all accessories and fittings as per

direction of engineer in charge

Providing and fixing Wooden Ceiling. wood frame works supported from GI hangers with anchor

fasteners, 19mm thick BWP and anti termite treated ply fixed to to wood framing perfect in

level+3 MM max. MDF with 1 mm thick laminate, including making grooves at the junction of

ceiling and walls / columns / partitions, including providing necessary cutout for light fittings, A/C

grills etc. including , extra frame work for fixing light fixtures etc. complete as per manufacturers

specifications and as required - Straight & Curved , complete in all respect as approved by the

Engineer-in-Charge

P/F G.I stud framework 600x600mm c/c -GI studs 48x34x36x0.5mm & GI ceiling section

80x26x51x0.5mm at 600x600mm c/c to be fixed on solid wall with expandable anchor fastness

65x10mm dia , to be fixed on each vertrifed I stud @1000mm spacing . The framework cavity to

be filled with thermal bonded polyster wadding 50mm thickness and 1000 GSM density P/F

Acoustic wall panelling with groved/ perforated wooden slats , density 700 kg/cum , FR grade ,

with the help of aluminium keel sections & z clips , to be fixed on GI stud framework mentinoed

above in this item.NRC- 0.80 . (ON CEILING)

P/F G.I stud framework 600x600mm c/c -GI studs 48x34x36x0.5mm & GI ceiling section

80x26x51x0.5mm at 600x600mm c/c to be fixed on solid wall with expandable anchor fastness

65x10mm dia , to be fixed on each vertrifed I stud @1000mm spacing . The framework cavity to

be filled with thermal bonded polyster wadding 50mm thickness and 1000 GSM density P/F

31 NSI 19 strechable acoustic fabric systems FR grade, NRC 0.95, Fabric (acoustically transparent) to be

fixed on rigid vinyl tracks (pvc grippers) , to be fixed on 10mm thick plywoood battens (100mm

width) , to be fixed on pine wood wool boards 20mm thickness , density 400kg/cum

Digitally signed 16 ANUJ

Providing and fixing frameless glass partition with 12mm thick clear toughened glass as per

design fitted over aluminium U channels(19*25) or as directed by Client ,embedded in the floor

and supported at top as detailed. The partition frame work above false ceiling to be fitted firmly

32 NSI 20 to the true ceiling with necessary anchor fasteners. All the edges of glass shall have pencil

nosing and machine polished. The joints in glass shall be filled with colourless silicone sealant

as per manufacturer specifications.(excluding the cost of aluminium channels) complete in all

respect as per direction of engineer in charge Sqm 51.000 4912.00 250,512.00

P/F G.I stud framework 600x600mm c/c -GI studs 48x34x36x0.5mm & GI ceiling section

80x26x51x0.5mm at 600x600mm c/c to be fixed on solid wall with expandable anchor fastness

65x10mm dia , to be fixed on each vertrifed I stud @1000mm spacing . The framework cavity to

be filled with thermal bonded polyster wadding 50mm thickness and 1000 GSM density P/F

Acoustic wall panelling with groved/ perforated wooden slats , density 700 kg/cum , FR grade ,

with the help of aluminium keel sections & z clips , to be fixed on GI stud framework mentinoed

above in this item. The size of the lineal panels is 2400mmx128mmx16 mm with a pitch of 14

mm. NRC- 0.80 . (ON WALL)

P/F black acoustical Pet panels / Eco panel 9mm thickness , made from 100% polyethylene

terephthalate (PET) , density 180kg/cum to be fixed on 8 mm thickness WPC board (wood

polimer composite board) battens 100mm width framework 600x600 mm c/c. complete in all

respect as per direction of Engineer in charge Sqm 301.240 4181.00 1,259,484.00

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing

lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS

36 NSI 23 :12823 marked, with necessary fixing arrangements and screws, including drilling necessary

holes for rawl plugs etc. and priming coat on unexposed surface complete in all respect as per

direction of Engineer in charge Rmtr 340.000 685.00 232,900.00

WOODEN PANELLING

Providing and fixing in wall panneling 19mm commercial ply with 0.8 mm back laminate fixed

with 25x 25mm wooden section in 18 - 20 guage placed aprox 24" c/c then 03 mm thick max.

MDF Board to be fixed over it and on the top 2mm veneer plain lining with necessary screws

37 NSI 24 /synthetic resin adhesiveed to be fix including making of grooves whose sides also to be finished

by fixing 2 mm thick veneer on all exposed faces with necessary adhesive etc finishing with

melamine polish (matt finish) on all veenered surfaces etc. all complete .as per architectural

drawings and the direction of Engineer -in-charge

Providing and fixing 6mm thk Mirror of approved quality, including supporting 12 mm ply, with

Black powder coated alumiumn frame, backing, nail, screw, adhesive, primer, including 3 or

more coats of specified Bronze Finish as specified in details / specification or as per control

sample board as approved colour shade or as specified in drawing and specification including all

necessary fixing arrangement etc complete as per design, drawing, specification and as per

instruction of Engineer-In-Charge. Sqm 33.099 5980.00 197,932.00

MAIN CURTAIN made out croton Velbert curtain cloth with horizontal sliding arrangement

complete with fixing rails, brackets, sliding arrangement & motorized operation complete with

runners, master runners, pullies, 3mm steel wire rope, 1 HP motor 2nos. air breaker contactors

39 NSI 26 , 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions.

The curtain should be draped to half area when in closed position. Minimum overlap at centre

should be 900mm and should be stitched in double gathering Size :- 18X8M

Digitally signed 17 ANUJ

WINGS :-SITC Providing and fixing cloth wings made out of black glazed cotton cloth, with fixed

on 6mm thick commercial plywood fixed on both side of MS 50mm x 25mmx 16G pipe wielded

frame work. The pipe framework made out of 25mm x 50 mm pipe. c/c 900 x 900 fixed with

overhead pivote track complete with duly painted on framework. Cost inclusive of both glazzed

cotton fabric and wing MS structure complete in all respect

MAIN FRILLS :-SITC Providing and fixing average frills made out of double gathering velvet

41 NSI 28 cotton cloth to be installed above the stage on 28mm dia ms pipe. Cost inclusive of both velvet

fabric and wing MS structure complete in all respect No. 1.000 28799.00 28,799.00

P/F STAGE Procenium , with groved / perforated wooden slats on the front face and black PET

panels on the back side to be made from MS pipe square , 50x502x2.5mm thickness, to be

grouted with MS angle brackets on the side walls and floor complete in all respect as per

architectural drawings and the direction of Engineer -in-charge Sqm 165.750 7724.00 1,280,253.00

Roller Blinds : Providing and fixing of Roller Shades- System Seclusion Block out fabric made up

of 100% Polyester with Acrylic coated of 0.32mm(PVC free) of thickness 0.50mm ±5% and

weighing 270-295gsm with openness factor of 0% .Shrinkage % Warp<0.5 & Weft <0.5,Color

fastness>5-6. Control system Clutch Operated: Engineered heavy duty chain drive pulley

operating system consisting of gear clutch housing and locking plug containing 6 ribs and

flexible to be inserted in 37mm or 50mm Roller tube. It is self lubricating exclusive clutch with

safety pins for secure bracket installation and unlocking pin for quick manual removal. Universal

clutch is most convenient for large windows down to the smallest windows. It shall be driven by a

ball chain pulley with plastic ball chain and can be universally positioned either Right hand or

Left hand side of the shade. Clutch gear ratio 1.75:1for reduced operating force on larger blinds.

Tube bearing plug Idler: Exclusive self lubricating spring loaded plastic bearing end plug with

positive locking wheel allows for adjustment and provides for a secure installation and removal

of shade. Tube bearing plug contains 6 ribs and flexible to be inserted in 37mm or 50mm roller

tube. Mounting Hardware Brackets: Universal brackets including end plug bracket with lock

down retainer device. Brackets finish of powder coated Aluminium installation brackets made of

43 NSI 30 stamped and hardened steel with 46mm projection for wall, ceiling and side fitting with screws

and end cap covers. Roller Tube: Circular-shaped aluminium tube extruded from alloy 6060 and

temper T66 – EN755 of 37mm inside diameter and outside diameter 40.2mm extruded tube to

have a 1.6mm wall thickness with standard anodized natural finish. Heavily reinforced with

minimum six internal ribs providing additional deflection strength and allows for secure

placements of clutch and end plug. Bottom Rail: Flat-shaped extruded aluminium from alloy

6060 and temper T66 – EN755 of dimension 13mm * 30mm and wall thickness of 1.5mm and

weight more than 350g/m providing additional stability to avoid swaging and damage of shade

fabric. Rail standard finish of powder coat white colour and provided end cover. Ball Chain: Shall

be 2mm diameter cord with 4.5mm diameter acetal balls moulded coaxially to it on 11.8mm

pitch to form an endless ball chain. It is used for raising or lowering action of the shades. Plastic

parts: All plastic components are UV-stable compounds available white colour.

Digitally signed 18 ANUJ

Designing, fabricating, testing, protection, installing and fixing in position operable wall system

raw MDF fire rated 100 mm thickness with 50 dB sound rating (high Acoustics ), aluminium

trims and parallel stacking (two Roller system ) of for all heights and all levels, including: all as

44 NSI 31 specified in details / specification or as per control sample board as approved colour shade or as

specified in drawing and specification including all necessary fixing arrangement etc complete as

per design, drawing, specification and as per instruction of Engineer-In-Charge. ( size Length

Providing and fixing Of PU studs/strips for disable people in the floor with addesive complete

with engineer in charge.

Stage Ceiling Room Specification :- Providing & Fixing Black Colour Magnesite Bonded Wood

Wool Acoustical Ceiling with Square edge 15 mm thickness easily demountable tile .Ceiling tiles

having NRC upto 0.90 of size 595x595 mm. Which will comprise of density 400 kg/m3 base

panel with humidity resistance of 90% RH and light reflectance as per colour dependent up to 3-

4 % (Black) & meet the stringent fire test required having Class ‘P’ rating for Ignitability test as

per BS 476 part 5 and Class ‘1’ rating as per BS 476 part 7 for Surface Spread of Flame test.

Class ‘P’ and Class ‘1’ are the highest rating. BS 476 part 6 Fire Propagation index and for

Flaming ISO 1182 and Smoke density as per ASTM E 662 besides base panel . Ceiling Tile to

be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised

iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising

of main-T runners of size 24x32 mm of length 3000 mm, cross - T of size 24x23 mm of length

46 NSI 33 1200 mm and secondary intermediate cross-T of size 24x23 mm of length 600mm to form grid

module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items

(galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6

mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size

85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to

be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to

center and 40 mm long dry wall wood screws. The 50 mm polyester wool infill having denisty

1000 gsm having flammibality - IS 15061-2002 Annexure clause A 3.2 overlaid on the frame

work.The work shall be carried out as per specifications, drawing and as per directions of the

Engineer-in-Charge.

Providing and fixing (S. S Railing with Glass) - Floor mounted, supply and installation, SS 304

grade 1050 mm high railing made of SS 304 grade handrail pipe of 50mm OD and 1.6 mm

thickness polish with automatic round polishing machine to get a uniform hairline finish K240

fixed with U clip at floor level and SS Railing to hold the infill glass of 12mm, thick toughened

and laminated, screws and other accessories to be used in SS 304 grade. To be used on

staircase and projection. Rmtr 68.000 11965.00 813,620.00

Digitally signed 19 ANUJ

Canopy:Providing and fixing Canopy of required size, aesthetically pleasing design (covering

entrance areas) with minimum elevation face / depth of 0.6m,using MS structure stiffener & base

/ top plate as per design and the members of space frame shall be made out of MS

tube,nominal bore / heavy class confirming to IS-1239 with 0.5 mm thick(TeT) finished with ACP

sheet. Contractor shall furnish material quality warranty certificate for 10 years period from ACP

manufacturer. Scope shall include supply and fixing ACP with framework suggested or approved

by EIC or architect and as per detailed drawing with cutting, bending and fixing in true line and

shape with screw at every 9" distance and filling up joints or grooves with approved/suggested

black/transparent/approved silicone as directed by architect/EIC. ACP colour shall match with

client branding colour. Other than approved ACP make, if client required colour is available in

other make needs to be get approved fron client EIC based on manufacturing technical data

sheet and assurance for required warranty. Client shall reserve rights to approve the make

matching with their branding colour.

Providing and fixing white sand stone brackets 90x22.5x45 cm sunk and moulded including

providing and fixing with 4 Nos gun metal cramp 25x6 mm 30 cm long

Providing and fixing of Anti slip luminous aluminium round edge tile trim nosing of size 48x25

mm of desired length and thickness as per the design. Finished in silver / champagne or as

dersired colour. Surface treated in stain/shiny/brushed or as desired. Complete in all respect as

per direction of Engineer in charge meter 231.200 1121.00 259,175.00

Double Skin Insulated Roofing System: -

Top Sheet:- Supply & Installation of colour coated profile sheet of nominal 1015 mm effective

width and nominal 28 mm deep ribs with subtle square fluting in the five pan at nominal 203 mm

centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of

water through the lateral overlap. The feed material shall be of 0.50 mm Total Coated Thickness

(0.45 mm BMT)Ultra steel- High tensile with min 550 MPa yield strength, metallic hot-dipped

coated with Al-Zn alloy (55% Aluminium, 43.5% Zinc, 1.5% Si ) as per AS1397 / IS15961 -

AZ150 (min. 150 g/m2 total on both sides) with Super Durable Polyester quality paint system of

50 NSI 38 approved color, suitable for exterior application conforming to AS/NZS 2728 type-4 / IS15965

class 3 make. The sheet shall have a total coating thickness of 35 microns, super durable

polyester with solar reflectance technology quality paint system of 20 micronson exposed

surface and 5 micron reverse polyester coat on back surface over 5 micron primer coat on both

surfaces. The paint systemwould have stable resin & inorganic pigments for paint durability and

is lead free for water harvesting. Complete in all respect as per direction of Engineer in charge.

Price does not include installation, loading, unloading, freight and accessories

Acoustic Doors: Supply & fixing of 83mm thick, having 38 dB acoustic cum fire check door

shutters, having Fire rating 120 Minutes minimum, including door frame of section 145mm x

75mm wood fixed to the door jambs with anchor fastners as required, having infill of 47mm thick

resin bonded glasswool of 24kg / cum density coated with FR Acrylic Sealant Sandwitched

between two 9 mm thick calcium silicate boards 100% without asbestos, Brucite and

Meerschaum having a density not more than 1150kg / cum and thermal conductivity 0.14 W/MK

51 NSI 39 faced with 8mm thick commericial ply with heat activated intumescent fire seal strip of size

10mm x 4mm mounted in the grooves having hardwood lipping of size 15mm x 70mm and fire

retradant 1mm thick laminate facing on both sides in desired shade and colour. The door to be

complete with all acoustic seals RP 24,16 & 38. The work shall be executed as per drawings

specifications & instructions of engineer in charge. (Note: Contractor to submit shop drawing &

Test certificates from manufacturer).

Digitally signed 20 ANUJ

ProvidingandfixingGIhexagonalchickenwiremeshofsize12mmx22gatthejunctionofdisimilarsurface

sofbrickRCCcolumnbybeamsandthelikeincludingnecessarynailsforfixingetc,completeallasperspe

cificationanddirectionofEngineer-in-chargeforallflooratall heights.

Total amount for non schedule items 54,643,013.00

Total amount for non schedule items 54,643,013.00

Total Finishing Cost (schedule+non schedule item) 134,634,543.55

Digitally signed 21 ANUJ

NAME OF PROJECT : RANI LAXSHMI BAI AUDITORIUM, JHANSI

Abstruct of Furniture works

DSR Amount MR Amount

S. No. Description of Item

1 Sub head-1: Furniture work of Auditorium Building - 15,193,950.00

TOTAL M.R. + DSR 15,193,950.00

Digitally signed by ANUJ

Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for RLBCAU Jhansi UP”.

DSR Qty Unit DSR Market DSR Market Amount

Item 2023 Rate Rate (Rs.) Amou (Rs.)

Description of Item

1 MR-1 VIP DINING TABLE (8 SEATER): Providing and placing 8 seater dining table of overall size approx.

Rubber wood framework ensures longevity, and natural wood tone with glossy PU upholstery portrays

appealing aesthetics.complete in all respect as per direction of Engineer in charge

2 MR-2 VIP Dining chair: Providing and placing dining chair of size Length: 570mm , Width : 480mm , Height : 850mm

Seating Height : 460mm. The chair comes with ivory tint of the seat, and the rich walnut textures of its legs.

complete in all respect as per direction of Engineer in charge

3 MR-3 VIP ROOM SOFA (3 SEATER): Provind and placing 3 seater sofa of size approx. 1920mm(W)x860mm(D), seat

height 450mm. • Crafted from long lasting Sheesham wood, making it extremely sturdy and resilient to insects,

fungus, and mold. • Recron-filled cushions for back support, and soft foam for comfortable seating. complete in

all respect as per direction of Engineer in charge each 3 57893.00 173679.00

4 MR-4 VIP ROOM CENTER TABLE: Providing and placing centre table of size approx.

1310mm(W)x700mm(D)x380MM(h)• Sturdy Shesham wood frame, solid wooden legs, and tempered glass

top.• Luxurious aesthetic that is neatly lined with the form and shape of the table.• Versatile glass top in a

neutral colour and contrasting darker legs in walnut shade.• Easy to maintain, with ground clearance for

cleaning.• 2 additional drawers that let you keep small accessories handy, complete in all respect as per

direction of Engineer in charge each 2 35749.00 71498.00

5 MR-5 VIP ROOM WING CHAIR: Providing and placing wing chair of size approx. 900mm (W)x 840mm (D)x1090(H),

Seat Height 480mm .

Pure Leather Upholstery - Pigmented Durable and ergonomically perfect for seating. S Spring Webbing-

Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply cross section

which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and

maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm ,

webbing 2 inch , Zigzag Spring - 3.8mm, Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning .Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of

ground clearance.complete in all respect as per direction of Engineer in charge

6 MR-6 DINING HALL TABLE (MOVABLE): Providing and placing dining table table of dimension approx. 1360mm(Dia

)x785mm(H).Table top is made of pristine white/suitable colour marble. • The 4-seat dining set is an efficient

space-saving option for compact spacesTable-Net Weight (kg)-129 . Finish Color-Walnut. Primary Material-

Ashwood.complete in all respect as per direction of Engineer in charge

7 MR-7 AUDITORIUM FRONT CHAIR: The overall dimensions of the chair shall be 76.1cm x 76.1cm x (113.6-131.1cm).

The seat height shall be 44.5cm-54.5cm. The cushioned seat and back is made of injection moulded Plastic

outer and Inner. Plaster inner is upholstered with stitched cover and moulded high Resilience Polyurethane

foam of density 45kg per meter cube. The stitched cover is made from spacer fabric and leatherette. Seat size

shall be 47cm x 48cm. The Back size shall be 45cm x 75.5cm. The armrests top is moulded from PU and

mounted on to a drop lift adjustment type tubular armrest support made of 3.8cm diameter x 0.2cm thick MS

ERW tube. The armrest height is adjustable uptp 6.5cm in 5 steps. The armrest structure is powder coated upto

40-60 microns. It shall have active bio synchro mechanism with features like 360 degree revolving, front pivot

tilt mechanism, tilt tension adjustment, 5-position tilt limiter, etc.. Seat depth adjustment is integrated in the

seat through a sliding mechanism. Seat depth adjustment range is 6cm. It shall also have adjustable back

support. Back frame is connected to Up/Down mechanism housed in plastic T spine. It can be adjusted fro

7.2cm for comfortable back support to suit individual need. The pneumatic height adjustment has an stroke of

10cm. The pedestal is injection moulded in black 33 % glass filled Nylon 66 and fitted with 5 nos. of twin wheel

castors. The pedestal is 66cm pitch center dia.. each 270 13970.00 3771900.00

Digitally signedPage

8 MR-8 AUDITORIUM CHAIR: Providing and Placing High Back Chair with seat Slide .SEAT ASSEMBLY: The seat

assembly is made of polyurethane foam molded with M.S. tubular frame insert which is upholstered with fabric.

The insert is tubular frame made of 01.9 $0.02cm x 0.16 0.013cm thk MS. E.R.W round tube with flexible

support straps running across the length and width of the frame. The Seat has an auto-tip up feature making it

stay in upright position when not in use enabling clear row passage.* Approx. Seat Size: 45.5cm (W) × 46.5cm

(D). BACKREST ASSEMBLY: The back assembly is made of polyurethane foam molded with M.S. tubular frame

insert, upholstered with fabric and has a plastic back cover. The insert is a tubular frame made of 01.9

+0.02cm x 0.16 10.013cm thk M.S.E.R.W round tube with flexible support straps running across the length and

width of the frame.* Approx. Back Size: High Back- 45.5cm (W) × 82.4cm (H).Mid Back- 45.5cm (W) × 70.4cm

(H).3. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is molded with density = 45

+/-3 kg/m.SIDE PANEL / AISLE PANEL: The chair rests on the ground on two side panel frames fabricated from

0.12+0.020cm thk CR steel sheet which is cladded with fabric upholstery. The side panel frame is grouted to

the floor using 2 nos. of anchors for each panel through 0.3 ‡ 0.05cm thk HR steel base plate.PU ARMREST :The

armrest is made up of integral skin Polyurethane Foam with 65 +/- 10 Shore 'A' Hardness and reinforced with

wooden insert. The armrest is snap fitted with side panel. complete in all respect as per direction of Engineer in

9 MR-9 CONFERENCE TABLE FOR 64 PEOPLE: Providing and Placing conference table of size two seater 1350 x 710 x

740 of 30 in nos. and 1 head module of 2350x710x740mm.Made of 36mm thick MDF-one side pre-laminate

board conforming to IS-14587:1998 with ace 0.4mm PVC membrane pressed on to top and having chamfered

edge. Full length access panel is provided with soft closing hinges inline with worktop edge. Worktop is

available in various shapes as shown . The understructure consist of mixture of 18mm and 25mm Thick Pre-

laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together.

Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-

12823:1990, Edge banded withwatching 2 mm thick PVC lipping. An array of panels made of 0.8mm and 1.2

mm CRCA MS IS: 513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and

cables. Cutout for ment Standard Anchor Roma 4 module is provided for electrical fittings in Straight two seater

and single seater modules below access flap per seat. The table isequipped with Extron cables cubby cutout as

standard offering only for 150° head module. For straight two seater and single seater modules, provision to

mount AV cables is provided (eg. HDMI,VGA-A, etc). Additional Wirecover made of 0.8mm Thick CRCA,

provided below worktop to conceal Microphone wires running from table top to wire tray.Company is ISO-

9001:2015,ISO 14001:2015,ISO-45001:2018, BIFMA and AIOTA certified. Product is Greenguard(UL) Certified. each 1 889164.00 889164.00

10 MR-10 CONFERENCE HB CHAIR: Providing and Placing in Position High Back Chair. The cushioned seats shall be made

of injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded

high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for

25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made

up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered

with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded from

polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular

armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish.

The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be

designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground and

contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range

of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin

wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to

pedestal. each 4 37230.00 148920.00

Digitally signedPage

11 MR-11 CONFERENCE MB CHAIR: Providing and Placing in Position Mid Back Chair. The overall dimensions shall be

76.1cm x 76.1cm x 96.5-114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of

injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded high

resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in

5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type,

front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt

angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth

adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in

plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit

individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal

shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal

shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having

6.0±0.1 cm wheel diameter and assembled to pedestal. each 60 32480.00 1948800.00

Total for Furniture work 15193950.00

Digitally signedPage

NAME OF PROJECT : Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc.

including external development work for RLBCAU Jhansi UP”.

SUMMARY OF PLUMBING WORKS

DSR Amount MR Amount

S. No. Description of Item

SUB HEAD - I - (SANITARY

1 FIXTURES & INTERNAL 2,480,229.69 1,436,418.72

SUB HEAD - II - (SOIL, WASTE,

RAIN WATER AND VENT PIPES)

SUB HEAD - III - (WATER

SUB HEAD - IV - (SEWERAGE

SUB HEAD - V - EXTERNAL

TOTAL M.R. + DSR 13,155,536.28

Digitally signed by ANUJ

Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for RLBCAU Jhansi UP”.

ITEMS - PLUMBING

DSR 2023 Qty Unit DSR Rate Market Rate DSR Amount (Rs.) Market Amount

Item no. Description of Item

SUB HEAD - I - (SANITARY FIXTURES & INTERNAL

1 17.78 Providing and fixing white vitreous china extended wall 57.95 Each 14,999.15 869,200.74 -

mounting water closet of size 780x370x690 mm of

approved shape including providing & fixing white

vitreous china cistern with dual flush fitting, of flushing

capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),

including seat cover, and cistern fittings, nuts, bolts and

gasket etc complete.

2 M.R.-1 Providing, fixing, testing and commissioning of star white colour 51.3 Each 3,426.00 - 175,753.80

vitreous china below / over counter Oval Wash Basin / circular

basin (Size 560 x 410 mm or as/architectural detail drawing) with

CP brass waste assembly, including piller tap complete

including CI / MS brackets duly painted, cutting and making

good the walls floors wherever required.

3 17.22A Providing and fixing CP Brass 32mm size Bottle Trap of 104.5 Each 1,034.80 108,136.60 -

approved quality & make and as per the direction of

Engineer in- charge.

4 17.31 Providing and fixing 600 x 450mm beveled edge mirror of 48.735 Each 1,607.95 78,363.44 -

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass

screws and washers complete in all respect.

5 M.R.-2 Providing and fixing C.P. brass towel ring with C.P. brass wall 48.735 Each 950.00 - 46,298.25

brackets & C.P brass screws complete in all respect.

6 18.21 Providing and fixing unplasticised PVC connection pipe with - -

18.21.2 45 cm length

7 M.R.-3 Providing and fixing C.P. brass liquid soap container with C.P. 48.735 Each 984.00 - 47,955.24

brass lid and brackets fixed to wall with wooden cleats and C.P.

brass screws, including cutting and making good the walls

wherever required complete in all respect.

8 17.34 Providing and fixing toilet paper holder. - -

9 M.R.-4 Providing and fixing CP brass twin coat hooks fixed on toilet 55.0525 Each 280.00 - 15,414.70

door/wall with CP brass screws, complete in all respect

Digitally signed

10 17.10 Providing and fixing stainless steel kitchen sink as per I.S.13983 - -

with C.I brackets and stainless steel plug 40mm including

painting of fittings and brackets, cutting and making good the

walls wherever required complete in all respect

10.1 17.10.1.3 Kitchen sink with drain board 510 x 1040 bowl depth 200 mm 2 Each 7,159.00 14,318.00 -

11 M.R. Providing, fixing, testing and commissioning of C.P. brass single - -

hole sink mixer with CP wall flange, swinging spout complete as

required and making good.

12 17.5 Providing and fixing white vitreous china flat back half stall urinal - -

of size 580x380x350 mm with white PVC automatic flushing

cistern, with fittings, standard size C.P. brass flush pipe,

spreaders with unions and clamps (all in C.P. brass) with waste

fitting as per IS : 2556, C.I. trap with outlet grating and other

couplings in C.P. brass, including painting of fittings and cutting

and making good the walls and floors wherever required :

12.1 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic 53.2 Each 12,071.75 642,217.10 -

flushing cistern

13 17.22A Providing and fixing CP Brass 32mm size Bottle Trap of 50.54 Each 1,034.80 - 52,298.79 -

approved quality & make and as per the direction of

Engineerin- charge.

14 8.10 Providing and fixing stone slab with table rubbed, edges rounded - -

and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in

urinal partitions by cutting a chase of appropriate width with

chase cutter and embedding the stone in the chase with epoxy

grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate 6 mm nominal size) as per direction of

Engineer-in-charge and finished smooth.

14.1 8.10.2 Granite Stone of approved shade 50.54 Each 4,051.85 204,780.50 -

15 M.R.-6 Providing and Fixing, testing & commissioning of ABS Health 55.0525 Each 2,431.00 - 133,832.63

Faucet (complete with hook and flexible tube min. Length 1.0 m)

as required complete in all respect

16 18.84 Providing and Fixing chrome plated brass battery based infrared - -

sensor operated pillar cock, having foam flow technology.

Digitally signed

17 M.R.-7 Supply, Installation, Testing and commissioning of wall hanging - -

drinking online water cooler with bottle filler facility, made by

stainless steel top and heavy duty galvanized steel frame. With

cooling capacity, ADA Compliant, size 472 mm Depth X 447mm

width, flexible bubbler guard , operated between 50 to 120 PSI,

Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat

control, suitable for 220-230v/50-60 hz A/C Supply Complete

with all accessories which include MD-CU29, which is an EPA

registered antimicrobial copper that fights off microorganisms

which include MRSA and e-coli. The water Fountain shall

possess NSF-USA, GRIHA, TUV, and to be placed at different

location of buidling. Agency has to execute all civil work for

installing the Water Fountain/Online water cooler for proper

functioning and aesthetic view as directed by the engineer-in-

charge without any extra cost.

17.1 M.R.-8 WITH 40 LPH RO System with 40 ltr HTP Storage tank. 40 4 Each 137,057.00 - 548,228.00

Lph RO System including with, RAW WATER PUMP, MICRON

FILTER, MEMBRANE HOUSING, Membrane Boosting Pump,

RO Membranes, CONTROL INSTRUMENTS, SKID Hanging

with Pressure tank of capacity of 60 Ltr.

18 M.R.-9 Providing and Fixing, testing & commissioning of C.P. brass tap - -

of approved quality conforming to IS standards.

18.1 15 mm nominal bore 5 Each 525.00 - 2,625.00

19 M.R.-10 Handicap toilet :-

19.1 Providing and fixing of WB 46 x 36 with one pair mounting 5 Each 28,032.00 - 140,160.00

brackets, EWC & Cistern complete with fittings & seat cover, one

no. hinged rail 76 cm & 4 nos. of grab rails 60 cm.

20 M.R.-11 Providing and fixing in position storage type automatic electric

water heater pressure/ non pressure type thermostatically

controlled, single phase, vertical wall mounted of (to the approval

of Engineer-In-Charge) with thermostats, inner container of

stainless steel complete with 1 Mtr three core flexible cord with

plug, non-return valve and pressure release valve complete

including fixing and testing complete in all respect.

21 M.R.-12 Supplying and fixing automatic 'NO-Touch ' SS electric hand-driers 10 Each 16,058.00 - 160,580.00

complete with all accessories & fittings

Digitally signed

M.R.-13 Providing and Fixing, testing & commissioning of C.P. brass angle

22 valve for basin mixer and geyser points of approved quality

conforming to IS:8931.

Total Carried to Summary 2,480,229.69 1,436,418.72

SUB HEAD - II - (SOIL, WASTE, RAIN WATER AND VENT - -

1 17.35 Providing and fixing soil, waste and vent pipes. - -

1.1.1 Cast Iron Hubless Pipes & Fittings as per IS:15905 621 Metre 1,169.30 725,819.59 -

Cast Iron Hubless Pipes & Fittings as per IS:15905 47 Metre 2,126.00 - 99,975.15

2 17.38 Providing and fixing bend of required degree with access door, - -

insertion rubber washer 3 mm thick, bolts and nuts complete.

2.1.1 17.38.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & 12 Nos. 567.20 7,041.56 -

outside as per IS:15905

3 17.39 Providing and fixing plain bend of required degree. - -

3.1.1 17.39.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & 155 Nos. 368.00 57,107.16 -

outside as per IS:15905

4 MR-15 Providing and fixing heel rest sanitary bend. - -

4.1.1 sand cast iron S&S as per IS-15905 13 Nos. 395.00 - 5,161.86

5 17.42 Providing and fixing double equal plain junction of required - -

5.1.1 17.42.1.3 Hubless Centrifugally cast (spun) iron pipes epoxy coated inside 10 Nos. 7,607.00 -

& outside IS:15905 760.7

6 MR-16 Providing and fixing single equal plain junction of required - -

degree with access door, insertion rubber washer 3mm thick,

bolts and nuts complete.

6.1.1 sand cast iron S&S as per IS-15905 32 Nos. 872.00 - 27,605.10

Digitally signed

6.2.1 sand cast iron S&S as per IS-15905 2 Nos. 2,030.00 - 5,024.25

7 17.44 Providing and fixing single equal plain junction of required - -

7.2.1 sand cast iron S&S as per IS-15905 2 Nos. 1,843.00 - 4,561.43

8 MR-19 Providing and fixing single unequal junction of required degree - -

with access door, insertion rubber washer 3mm thick, bolts and

8.1.1 sand cast iron S&S as per IS-15905 5 Nos. 1,090.00 - 5,697.65

8.2.1 sand cast iron S&S as per IS-15905 1 Nos. 2,128.00 - 2,991.54

9 17.56 Providing and fixing terminal guard. - -

9 17.57 Providing and fixing shielded coupling for Hubless CI pipe - -

9.1.1 17.57A.1.1 SS 304 grade coupling with EPDM rubber gasket 190 Nos. 432.05 82,089.50 -

9 17.57A Providing and fixing shielded coupling for Hubless CI pipe - -

9.1.1 17.57A.2.1 SS 304 grade coupling with EPDM rubber gasket 190 Nos. 389.05 73,919.50 -

10 MR-21 Providing and fixing collar:- - -

Sand cast iron S&S as per IS-15905 16 Nos. 659.00 - 10,329.83

Sand cast iron S&S as per IS-15905 207 Nos. 415.00 - 85,867.65

11 17.59 Providing and fixing M.S. stays and clamps for sand cast iron / - -

centrifugally cast (spun) iron pipes of diameter :

Digitally signed

12 17.60 Providing and fixing trap of self cleansing design with screwed - -

down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors:

17.60.1 100 mm inlet and 100 mm outlet

12.1 17.60.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & 89 Nos. 854.55 75,905.40 -

outside as per IS:15905

13 17.65 Painting sand cast iron / centrifugally cast (spun) iron soil, - -

waste vent pipes and fittings with paint of any colour such as

chocolate, grey, or buff etc. over a coat of primer (of approved

quality) for new work:

13.1 MR-23 150 mm diameter pipe 47 Metre 125.00 - 5,878.13

14 18.1 Providing and fixing G.I. (class-C) pipes and fittings conforming - -

to IS: 1239 clamps and hinges including cutting chases and

holes and making good the walls and ceiling for waste pipes

from wash basins, urinals kitchen sink and equipment waste

connections pump deliveries & suction & condensate drainage

15 4.1 Providing and laying in position cement concrete of specified - -

grade excluding the cost of centering and shuttering - All work

up to plinth level:

15.1 4.1.3 1:2:4 (1 cement :2 coarse sand: 4 hard stone aggregate 20mm 10 cum 7,878.50 78,785.00 -

and down gauge).

16 MR-24 Providing, fixing and jointing UV stabilized uPVC rain water - -

pipes conforming to IS:4985 (working pressure 6 kg/sqcm.)

including all fittings such as bends, clamps, tees, cowls, clean

out plugs etc including Fixing at wall / ceiling level supported by

steel clamps & hangers etc. including Cutting, chases/holes in

floors / walls / slab and making good the same after pipe have

been duly laid and testing complete in all respects.

16.1 (I) Single socketed pipes - -

Digitally signed

17 MR-25 Providing & fixing 75mm x 50mm G.I. waste with reducing elbow 30 Nos. 882.00 - 26,729.01

& nipple cutting chases, the floor / slab, repairs complete as

required and connection to GI / CI waste pipe.

18 MR-26 Providing and fixing Heavy Class SS grating with of approved 119 Nos. 986.00 - 117,462.18

design including setting in floor with cement motor to match with

floor finish as per architect requirement .

19 MR-27 Providing and fixing Heavy Class SS grating with Cockroach 113 Nos. 1,090.00 - 123,359.12

proof SS strainer of approved design including setting in floor

with cement motor to match with floor finish as per architect

requirement suitable for waster and FT

20 MR-28 Providing and fixing G.I. EXTENSION PIECE for 100 mm dia 89 Nos. 1,713.00 - 152,157.23

floor trap formed out of main pipe (Type A) with multiple side

inlets, suitable for various dia pipes, side connections, including

all fixtures and fittings as per site conditions and as per standard

details and water tight sealing of joints and area surrounding the

grating and as directed.

21 MR-29 Providing and fixing cleaning eye on horizontal CI soil & waste - -

pipes of 300 mm long GI medium class pipe with one plain end

lead caulked in to the collar of CI pipe and the other end with

flange which in covered by neoprene rubber gasket and blank

flange, complete with nuts, bolts etc and hot dip galvanization

after fabrication to the satisfaction of Engineer in Charge

Digitally signed

24.1 16.93 Providing and placing in position 100 mm thick factory made 70 sqm 3,081.95 214,709.18 -

machine batched & machine mixed Precast RCC Rectangular

Covers on drains of footpath of various sizes, of M-25 grade

cement concrete for RCC work, including cost of centering,

shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade

@ maximum 100mm c/c on both ways , neat cement punning on

finished surface, properly encased on all edges with 1.6 mm

thick , 100 mm wide MS sheet duly painted over priming coat ,

reinforcement to be welded at edges with MS sheet and

providing 2 Nos. 12 mm dia bar for hooks etc i/c

cost of cartage, all leads & lift, handling at site etc. all complete

as per direction of Engineer-in-Charge.

Total Carried to Summary 2,125,665.75 1,186,479.36

SUB HEAD - III - (WATER SUPPLY) - -

1 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) - -

pipes, having thermal stability for hot & cold water supply

including all CPVC plain & brass threaded fittings i/c fixing

the pipe with clamps at 1.00m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good

the same including testiang of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making good the - -

1.1 18.8.1 15 mm dia nominal bore 609 Metre 497.80 303,017.08 -

1.2 18.8.2 20 mm dia nominal bore 120 Metre 537.60 64,606.08 -

2 18.9 Providing and fixing, testing and commissioning of CPVC - -

(Chlorinate of polyvingle chloride) SCH - 40 pipe and fitting such

as tees, elbows, reducers. Male/female

connector, clamps etc. Jointing with CPVC solvent

cement as per manufacture recommendation confirming to

ASTM -F-493.The pipe fitting joining to be done with solvent

cement as per manufacturers specifications &

recommendations. This includes testing of joints complete as

per direction of Engineer-Incharge.

2.1 18.9.3 25 mm dia nominal bore 99 Metre 355.40 35,282.34 -

2.2 18.9.4 32 mm dia nominal bore 99 Metre 438.60 43,542.02 -

2.3 18.9.5 40 mm dia nominal bore 78 Metre 563.05 44,129.04 -

2.4 18.9.6 50 mm dia nominal bore 178 Metre 794.25 141,098.51 -

Digitally signed

4 MR-30 Providing & fixing full way lever operated forged brass ball valve - -

of brass body with forged brass hard chrome plated steel ball

tested to a pressure not less than 10 Kg / sqcm with threaded /

flanged joints complete with nuts, bolts, gaskets, washers etc.

5 MR-31 Providing and fixing motorised butterfly valve with float type - -

sensors suitable for 240 volts with working pressure rating of

not less than 5 kg/cm2 with control panel and sensors to open

valve when water level is low in tanks and to close when water

level is high in water tanks including necessary cables, conduits,

upto junction box etc., complete.

6 Providing and fixing Butter fly valve Rated for PN16 pressure - -

rating including rubber gasket, flanges, nuts, bolts, washers &

painting complete as required.

Total Carried to Summary 1,043,051.34 69,967.00

SUB HEAD - IV - (SEWERAGE AND DRAINAGE) - -

1 2.1 Excavating trenches by mechanical/ manual means of required - -

width for pipes, cables, etc including excavation for sockets, and

dressing of sides, ramming of bottoms, depth for all depths

including getting out the excavated soil, and then returning the

soil as required, in layers not exceeding 20 cm in depth including

consolidating each deposited layer by ramming, watering, etc.

and disposing of surplus excavated soil as directed, within a

1.1 2.10.1.2 Pipes, cables etc. exceeding 80mm dia. But not exceeding 960 Metre 352.15 337,887.93 -

Digitally signed

3 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. - -

pipes with collars jointed with stiff mixture of cement mortar in

the proportion of 1:2 (1 cement : 2 fine sand) including testing of

joints etc. complete.

4 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 - -

coarse sand : 10 graded stone aggregate 20 mm nominal size)

up to haunches of S.W./RCC pipes including bed concrete as

per standard design :

5 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 - -

with stiff mixture of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints etc. complete:

6 19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 fine - -

sand : 10 graded stone aggregate 20 mm nominal size) alround

S.W./RCC pipes including bed concrete as per standard design:

7 2.6 Earth work in excavation by mechanical means (Hydraulic - -

excavator)/manual means over areas (exceeding 30 cm in depth

1.5m in width as well as 10 sqm on plan) including disposal of

excavated earth, lead upto 50m and lift upto 1.5m, disposed

earth to be leveled and neatly dressed. (For Manholes)

8 19.7 Constructing brick masonry manhole cement mortar 1:4 (1 - -

cement : 4 coarse sand) R.C.C. top slab with 1:2:4 mix (

1cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size ), foundation concrete 1:4:8 mix (1cement : 4

coarse sand : 8 graded stone aggregate 20 mm nominal size)

inside plastering 12mm thick with cement mortar 1:3 (1 cement :

3 coarse sand) finished with floating coat of neat cement and

making necessary channels in cement concrete 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

finished with a floating coat of neat cement complete as per

standard design.

Digitally signed 10 ANUJ

8.1 19.7.1 Inside size 90 x 80 cm and 45 cm deep including C.I. cover with - -

frame (light duty) 455 x 610 mm internal dimensions total weight

of cover and frame to be not less than 38 kg (weight of cover 23

kg and weight of frame 15 kg)

8.1.1 19.7.1.1 With F.P.S. bricks with class designation 75 21.85 Nos. 12,770.55 279,036.52 -

8.2 19.7.2 Inside size 120x90 cm and 90 cm deep including C.I. cover with - -

frame (medium duty) 500 mm internal diameter, total weight of

cover and frame to be not less than 116 kg (weight of cover 58

kg and weight of frame 58 kg) :

8.2.1 19.7.2.1 With F.P.S. bricks with class designation 75 19 Nos. 26,405.50 501,704.50 -

9 19.8 Extra depth for manholes - -

9.1 19.8.1 Size 90 x 80 cm (With With F.P.S. bricks with class designation 9.5 Metre 8,825.40 83,841.30 -

9.2 19.8.2 Size 120 x 90 cm (With With F.P.S. bricks with class 9.5 Metre 10,585.50 100,562.25 -

designation 75)

10 19.27 Constructing brick masonry road gully chamber 50x45x60 cm - -

with bricks of class designation 75 in cement mortar 1:4 (1

cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C.

horizontal grating with frame complete as per standard design:

11 19.31 Extra depth beyond 45 cm of brick masonry chamber - -

12 19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 - -

complete with C.I. grating brick masonry chamber with water

tight C.I. cover with frame of 300 x300 mm size (inside) the

weight of cover to be not less than 4.50 kg and frame to be not

less than 2.70 kg as per standard design:

12.1.1 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class 14.25 Each 2,707.65 38,584.01 -

designation 7.5

Digitally signed 11 ANUJ

13 19.16 Providing orange colour safety foot rest of minimum 6 mm thick 100.7 Each 553.70 55,757.59 -

plastic encapsulated as per IS: 10910 on 12 mm dia steel bar

conforming to IS : 1786 having minimum cross section as 23

mm x 25 mm and over all minimum length 263 mm and width as

165 mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering

besides necessary and adequate anchoring projections on tail

length on 138 mm as per standard drawing and suitable to with

stand the bend test and chemical resistance test as per

specification and having manufacture's permanent identification

mark to be visible even after fixing, including fixing in manholes

with 30 x 20 x 15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal size)

complete as per design.

Total Carried to Summary 3,666,591.47 -

SUB HEAD - V - EXTERNAL WATER SUPPLY - -

1 2.10 Excavating trenches of required width for pipes, cables, etc - -

including excavation for sockets, and dressing of sides, ramming

of bottoms, depth upto 1.5 m, including getting out the

excavated soil, and then returning the soil as required, in layers

not exceeding 20 cm in depth, including consolidating each

deposited layer by ramming, watering, etc. and disposing of

surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil - -

1.1 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. 617.5 Metre 215.60 133,133.00 -

1.2 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 237.5 Metre 352.15 83,635.63 -

2 18.72 Providing and laying S&S Centrifugally Cast (Spun)/Ductile Iron - -

pipes confirming to is:8329:

2.1 18.72.16 100 mm dia Ductile Iron Class K-9 pipes 238 Metre 1,837.75 436,465.63 -

3 18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron pipes - -

or Ductile Iron Pipes including testing of joints and including the

cost of rubber gasket.

4 18.12 Providing and fixing G.I. pipes complete with G.I. fittings - -

including trenching and refilling etc.

4.2 MR-36 100 mm dia nominal bore 47.5 Metre 1,165.00 - 55,337.50

Digitally signed 12 ANUJ

5 18.4 Painting G.I. pipes and fittings with two coats of anti-corrosive - -

bitumastic paint of approved quality :

5.2 MR-37 100 mm diameter pipe 47.5 Metre 103.00 - 4,892.50

6 MR-38 Providing, fixing, joints and testing in position the following - -

UPVC Pipe conferming to IS:4985 of 6kg sqcm for garden

irrigation system cut to required length pipe to be laid below

level in trenches up to required depth, including excavation in all

kind of soil (hard rock) dewatering, refilling, watering, ramming

and removing the surplus excavated material and putting 100 m

sand alround and making good the same.

7 MR-39 Providing & fixing in position 25 mm dia lawn hydrants consisting 19 Each 651.00 - 12,369.00

of 25 mm dia Ball valve, GI nipple and threaded hose receiver

complete as required.

8 18.31 Providing and fixing C.I. sluice valves (with cap) complete with - -

bolts, nuts, rubber insertions etc. (the tail pieces if required will

be paid separately) :

9 18.33 Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 - -

class designation brick work in cement mortar 1:4 (1 cement : 4

fine sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and180 mm deep (inside)

with chain lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) necessary

excavation foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12

mm thick finished with a floating coat of neat cement complete

as per standard design.

Digitally signed 13 ANUJ

10 18.32 Constructing masonry Chamber 30 x 30 x 55 cm, inside with 75 - -

class designation brick work in cement mortar 1:4 (1 cement : 4

fine sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and180 mm deep (inside)

with chain lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) necessary

excavation foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12

mm thick finished with a floating coat of neat cement complete

as per standard design.

11 18.41 Providing and filling sand of grading zone V or coarser grade - -

alround the G.I. pipes in external work.

12 18.59 Providing and fixing C.I. double acting air valve of approved - -

quality with bolts, nuts, rubber insertions etc. complete (The tail

pieces, tapers etc. if required will be paid separately)

13 18.60 Providing and fixing enclosed type water meter (bulk type) - -

conforming to IS : 2373 and tested by Municipal Board complete

with bolts, nuts, rubber insertions etc. (The tall pieces if required

will be paid separately)

Total Carried to Summary 819,829.96 258,181.50

Digitally signed 14 ANUJ

Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for

RLBCAU Jhansi UP”.

Abstruct of cost

DSR Amount Market Amount

Sl. No. Description of Item

1 SUB HEAD - I - DISTRIBUTION PANELS 0.00 1618964.00

2 SUB HEAD - II - POINT WIRING 9769764.77 0.00

3 SUB HEAD - III - (TELEPHONE / TV / DATA SYSTEM) 346307.24 9465.50

4 SUB HEAD - IV - DISTRIBUTION BOARD/ RACEWAYS 303041.56 145616.00

5 SUB HEAD - V - LIGHT FIXTURES AND FANS 320201.04 7561585.60

6 SUB HEAD - VI - LIGHTENING PROTECTION SYSTEM 0.00 576973.30

7 SUB HEAD - VII - Solar 0.00 322358.00

8 SECTION - VIII - (CABLES, CABLE TRAY) 1191981.11 4999391.90

9 SUB HEAD - IX - CHEMICAL EARTHING 253711.89 219936.50

10 SUBHEAD - X : AUTOMATIC GAS BASED PANEL PROTECTION 0.00 955131.50

11 SECTION - XI - SAFETY EQUIPMENTS & MISCELLANEOUS 305059.71 198251.25

12 SECTION - XII - UPS 0.00 658770.00

13 SUB-HEAD - XIII - EXTERNAL LIGHTING 217719.18 3262897.75

TOTAL DSR + MR 33237127.80

Digitally signed by ANUJ

NAME OF PROJECT: Construction of 700 seater Auditorium with Museum, dining hall, senate hall etc. including external development work for RLBCAU Jhansi UP”.

(SH: SITC OF ELECTRICAL WORK )

SCHEDULE OF QUANTITIES: Electrical Works

Including GST Market Market

DSR Rate DSR Amount

S. No. DSR- 2022 Description of Item Unit QTY @ 18% Factor Rate Amount

(DSR Rate * (Rs.) (Rs.)

SUB HEAD - I - DISTRIBUTION PANELS

The rates for the distribution boards from the Breakers and instruments

shall also include the following:

NOTE: The following provisions shall be required to be made in the

switchboard detailed below:

a. The Switchboard shall have provision for entry of all PVC cables / bus duct

from the top / bottom as required.

b. All live accessible parts shall be shrouded and all equipment shall be ginger

touch proof. The busbar insulation shall be with heat shrinkable sleeves SMC

/ DMC shrouds and busbar supports shall be used.

c. Suitable tinned copper extension links for incoming / outgoing cables shall

be provided wherever required.

d. Control circuits includes breaker control switch, auto manual selector switch,

anti pumping relay, spring charging trip indication, TIMER, Control wiring,

Auxiliary contactors MCB's as required at site.

e. All the incomers breaker shall be interlocked with micro PLC to avoid parallel

operation . Stabilized separate power supply to be provided for micro PLC

hand wiring interlocking shall also be provided.

f. All the incomers breaker having microprocessor breaker shall have neutral

g. All fault level breaking capacity indicates shall be I.C.S. value at 415 volts.

(ICS=ICU=ICW=100%) for 1 sec

h. All MCCB above 250 Amp shall have variable overload and short circuit

i. All ACB/MCCB shall have with Rotary Handles.

j. Space heater / light / air filter shall be provided for each vertical

k. Padlocking facility shall be provided on all outgoing feeders

m All ACB's shall have all standard accessories such as CT,s Arc Chute, safety

n All meter panel wiring from PLC to DG/TR/Bus coupler as required.

o. Link and drops from ACB / MCCB shall be designed for fall rated current of

ACB / MCCB rating at same amount of current density as of main busbar.

p. All panel should be on Ethernet with embedded web page to monitor

ON/OFF/Trip status of the breaker.

q. Compliance to the technical specifications.

r. All MCCB in main panel should have O/L, S/C, E/F protection with S/C and

E/F differtation.

s. The Panel should be IBMS compatible for ON/OFF/TRIP status

t All MFM shall have minimum sampling rate of 64 samples/cycle &

feature of individual Harmonic distortion upto 15th order.

1 DISTRIBUTION PANELS

1.1 LIGHT & POWER PANELS-LHS

Digitally signedPage

Supply of dust, damp and vermin proof cubicle free floor, indoor type factory

built sheet steel enclosed modular bolted construction extendable Panel,

suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire supply

system fabricated out of Form 3b compartmentalized design and covered

with CRCA sheet steel of 2mm thick for frame work and 1.6mm thick for

doors/ covers, 3mm thick for gland plates i/c cleaning & finishing complete

with 9 tank process for powder coating in approved shade, having extensible

type TPN Aluminium bus bars of high conductivity, SMC bus bar supports,

with short circuit with stand capacity of 35KA for 1 sec., bottom base

channel of section not less than ISMC 75mm, fabrication shall be done in

transportable sections, entire panel shall have a common copper earth bus

bar to switch gears with required size of Alum. bus bars and inter-

connection with solid copper conductor wires/ aluminium strips, neutral

links, including control wiring with 1.5sqmm. PVC insulated FRLS copper

conductor Single Core cable for voltage & 2.5sq.mm for current circuits,

cable alleys, cable gland plates in two half, danger notice plates, etc.

necessary metering protections & indications and mounted with the

following switch gears as per drawing and technical specifications etc.

complete as required.

630 Amps 4 Pole, 36 KA, MCCB with MP based releases.with 3 Nos. R,Y,B

Indication Lamps with 2A back up SP MCB with ON indication.MCCB shall be

provided with spreader link and direct rotary handle.

3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker 'ON'

3 phase 4 wire dual source type Multifunction meter of class 0.5S accuracy

with communication interface port RS 485 for recording V V ( Between

Phases and between each phase and neutral ), A ( In each Phase and

neutral), KVA, KW, KWhr, KVAR, pf, 64 samples/cycle, Total harmonic

distortion, with suitable rating CTs etc. complete with wiring , connections

2 / Class C SPD- surge protection device

TPN aluminium bus bars of minimum of 500 A 36 kA capacity with heat

shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc.

III) Outgoings

Supplying and fixing following outgoing MCCB/MCB including connection,

inter-connection etc. with suitable size of wires complete as required.(Each

MCB/MCCB to be provided with ON indiation with 2A backup SP MCB)

250 Amp 4P MCCB '10 KA' - 4 No.( 1 for Ele floor panel(RHS) + 2 Nos. for

AHU panels + spare

100 Amp 4P MCCB '10 KA' - 3 Nos (1 No. UPS + 1 No. ventilation panel +

63 Amp 4P MCCB '10 KA' - 2 Nos

63 Amp 4P MCB '10 KA' - 7 Nos

40 Amp 4P MCB '10 KA' - 3 Nos

40 Amp DP MCB '10 KA' - 2 Nos

MR-1.1 panel described as above Set 1 244181.00 244181.00

1.2 MR Light & Power Panel-2-RHS

1 No. - 315 Amp. 16ka 4 pole Thermal release, MCCB (Ics=lcu) with O/L,

S/C & modular earth fault protection.

3 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup

2 / Class C SPD- surge protection device

Digitally signedPage

TPN aluminium bus bars of minimum of 300 A 25 kA capacity with heat

shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc.

(Following MCB (Ics=Icu upto 433 V) thermal magnetic release with over

current and short circuit releases, all indication, )

250 Amp 4P MCCB '10 KA' - 4 No.( 1 No. for AHU panels )

6 Nos. 63A 4P MCB 'C' 10 kA breaking capacity.

4 Nos. 40A 4P MCB 'C' 10 kA breaking capacity.

3 Nos. 40A DP MCB 'C' 10 kA breaking capacity.

MR-1.2 Panel Described as above. Set 1 168045.00 168045.00

2 UPS Output Panel

Supplying, installation , testing and comissioning of cubical type LT panel

suitable double door for 415Volts 3 phase 4wire 50 Hz AC supply system

fabricated in compartmentalized design from CRCA sheet steel of 2 mm

thick for frame work and covers , 3 mmthick for gland plates including

cleaning and finishing complte with 9 tank process for power coating in

approved shade extensible type TPN aluminium alloy bus bars of high

conductivity DMC/SMC bus bars supports with short circuit withstand

capacity of 31 MVA for 1 second, bottom base channel of MS section not

less than 100mmx 50 mmx 5mm thick, fabrication shall be done in

transportable setctions, entire panel shall have a common copper earthbar

of size25 mm x 5 mm at the rear with 2 No earth stud solid connections

from main bus bars to switchgears with required size of aluminium bus bars

and control wiring with 2.5 Sq. mm PVCinsulated copper conductor FRLS

cable alleys cable gland and plates in bottom half ,including providing

following switchgars .

1 No. 100A 4P MCCB having breaking capacity 35 KA (Ics=Icu)

microprocessor based releaase with E/F,o/c,s/c protection release all

indication,front operating handle & door interlock

Digital type voltmeter with selector switch with 2A backup MCB -3 Sets

Digital type ammeter (0-100Amp) with selector switch and 1 set of 3

Nos.CT's of ratio 100/5A, Class-1 accuracy and 15 VA burden -1 Set

3 Nos. Phase indicating LED lamps with 2 Amp backup MCB as required - 2

4P Copper bus bars of minimum of 150Amp with heat shrinkable coloured

sleeves and including BMC/SMC bus bars supports at required interval

complete for cross section, side supports and their spacing etc. for

withstanding fault level of 31 MVA for 1 sec

6 Nos. 63A 4P MCB 'C' 10 kA breaking capacity.

4 Nos. 63A DP MCB 'C' 10 kA breaking capacity.

MR-2 Panel described as above 1 Set 52258.00 52258.00

3. External Lighting Feeder Piller

Digitally signedPage

Fabrication, supplying and installation of outdoor type cubical feeder pillar of

suitable size not less than 30 cm and upto 45 cm deep made out of M.S.

sheet 2mm thick (14 SWG) duly compartmentalized having 4 strip busbar of

150 Amp capacity double door with locking arrangement for protection from

rain, dust, duly fixed on MS angle iron frame work of size 50mm x 50mm x

6mm (NS) 90 cm long legs out of which 45 cm duly grouted in cement

concrete 1:2:4 (1 cement : 2 sand :4 stone aggrete 20mm) and having

following accessories mouted inside the cubical panel i/c connection, inter

connection with aluminium thimbles, earthing with two nos. earth struds

duly painted with one coat of red oxide & two coats of superior quality

enamel paint complete etc. as reqd.

Supplying & fixing of following accessories in the existing cubical panel

board / feeder pillar including connection testing and having provision for

energy meter inside panel etc. as reqd.

a) 100A 4P MCCB,25KA thermal magnetiv release - 1 No.

b) Voltmeter 0-500 V , digital type with selector switch-1 no.

c) Ammeter 0- 100 A ,digital type with selector switch and CT's of suitable

d) Indication lamps (RYB) LED type with protection MCB's - 1 set

e) Auto Manual Selector Switch - 1 No.

a) TPN Al bus bar of 150A rating

40A 4P MCB,16 KA -4 Nos.

a) 63A 4P MCB,16 KA -1 Nos.

b) 70A, TP Power Contactor - 3 Nos.

c) Astronomical Time Switch with daily dial suitable for operation on 440V

three phase 50Hz AC supply - 1 No. (Rex Timer (Legrand Make)

d) Auto Manual Selector Switch - 1 No.

a) TPN Al bus bar of 100A rating

e) 32A TP MCB - 6 Nos.

f) 32A DP MCB - 8 Nos.

g) Danger notice plate --1 no.

MR-3 External Light Panel as above 1 set 79111.00 79111.00

4 PLUMBING PANEL

Supplying, Installation, Testing and Commissioning of dust and vermin proof

indoor type (IP 42) floor mounted, modular type, totally enclosed,

extendable Motor Control Centre (MCC) suitable for operation on 415 V, 50

Hz, 3 phase AC, 4 wire supply system, fabricated out of 4b

compartmentalised design & covered with CRCA sheet steel of 2.0 mm thick

for frame work, 1.6 mm thick for doors/ covers and 3.0 mm thick for gland

plates including suitable TPN Aluminium bus bars of high conductivity,

DMC/SMC supports for busbar sleeves, bottom base channel of section not

less than 100 mm ISMC, connections from main busbar to switchgears

using required Aluminium busbar / solid conductors, control wiring with 1.5

sqmm PVC insulated FRLS Copper conductor single core cable for voltage

and 2.5 sqmm for current circuit, cable alleys, cable gland plates, common

Copper earth bar of suitable size with 2 nos. earth studs etc. as required as

per technical specification. The panel shall have short circuit withstand

capacity 35 KA for 1.0 sec. Panel shall provided with required software and

hardware for integration of all incoming & outgiong feeders with BMS

Digitally signedPage

63A, 4P, 10 kA rating MCB - 1 No.

Intellingent MFM digital to read V, A, KW, KWH having RS 485 Port with 3

nos. resin cast CTs of 60/5A class 1.0 accuracy and 15 VA burden - 1 set

Coloured LED (Red, Yellow, Blue) phase indicating lamps with 2 Amps.

control MCBs.- 1 Set of 3 Nos.

Electrolytic high conductivity aluminium three phase and neutral busbars

rated at 415V, 100 amps, 50Hz, AC, insulated with heat shrinkable coloured

PVC sleeves & clip on shrouds for joints.

All outgoing shall be provided with ON indication lamp with 2A SP MCB for

Fully automatic DOL starter for 2 KW motor complete with suitable rating

MPCB incomer, contactors, overload protection relay, current sensing type

single phase preventor, ON/OFF indications, push buttons, auto / manual /

off selector switch, Digital Ammeter with CT's and all other accessories with

suitable rating PVC insulated FRLS single core copper conductor cable etc.

complete as required. - 2 Nos-1W+1S ( Filter feed water pump )

32A, 4P, 10 kA rating MCB - 2 Nos.(Hydroneumatic pump-domestic supply

pump 3 KW- (1W+1S)

4 Nos. 25A 4P MCB 'C' of 10kA Breaking Capacity - 2 No. sump pump+

32A, 4P, 10 kA rating MCB - 2 Nos.Spare

Note- The MPCB should be selected as per type -II coordination chart as per

manufacturer recommendation

MR-4 Panel described as above Set 1 61803.00 61803.00

5 FIRE FIGHTING PANEL

a) MCCB, 4 Pole, 250 A, 25 KA with microprocessor based and rotary handle

(ICS= ICU= 35 KA upto 415 V) - 1 sets.

b) Digital Ammeter (0 - 250 A), 96 mm. sq. CT operated with inbuilt selector

switch with 3 Nos. CT's of ratio 250/5 A, 15 VA burden and accuracy of class

c) Digital Volt Meter (0-500 V) 96 mm. sq. with inbuilt selector switch and

control MCBs - 2 Sets

d) Phase Indicating coloured LED (RYB) with control MCBs - 1 Sets

Electrolytic high conductivity aluminium three phase and neutral busbars

rated at 415V, 300 amps, 50Hz, AC, insulated with heat shrinkable coloured

PVC sleeves & clip on shrouds for joints.

Outgoing for Main Fire Pump and water curtain

a) MCCB 3 Pole, 125 A (with adjustable thermal magnetic release and

(Ics=Icu=25 KA upto 415 V), with CT operated digital Ammeter (0 - 160 A),

with 3 CT's of 125/5 A, 10 VA, accuracy 1.0, ASS and coloured LED for on

(Red) indication - 2 Set

b) Fully Automatic Star Delta Starter suitable for sprinkler Pump,Hydrant

Pump,Diesel Pump motor of minimum 45KW and (as per the

recommendation of pump manufacturer) complete with over load protection,

current sensing type single phase preventer complete with contactors, push

button, indicators LED type Auto/manual selector switches all accessories

and FRLS copper conductor wiring etc. as required - 2 Set

Outgoing for Pressurization Pump(Jockey)

a) MCB 3 Pole, 25 A, 10 KA with CT operated digital Ammeter (0 - 40 A), with

3 CT's of 40/5 A, 10 VA, accuracy 1.0, ASS and coloured LED for on (Red)

indication with adjustable thermal magnetic release and (ICS = 10 KA upto

Digitally signedPage

b) Fully Automatic DOL Starter suitable for Jockey Pump (Minimum 1.5 HP

capacity) complete with over load protection, current sensing type single

phase preventer complete with contactors, push button, indicators LED

type Auto/manual selector switch all accessories and wiring etc. as required -

MCB TP+N Pole, 63 A, 10 KA 'C' - 2 Set

MCB Double Pole, 16 A, 10 KA 'C' - 4 sets.

Diesel Engine Control

a) Auto / Manual selector switch and 3 attempt Starting device, Electronic

timer, Relays, Auxiliary switches, Rotary switches, Tripping relays,

Contactors, Push button for manual Start / Stop etc. to make the equipment

automatic as per functional requirement.

b) Battery charging unit suitable for 24 V DC with boost and trickle charger,

selector switch, with suitable rating transformer, rectifier, RC filter network,

fuses on AC and DC protection, 0 - 30 V DC Digital Volt meter, 0 - 20 A DC

Digital Ammeter, the charger should be cut off when the engine is started

and the batteries shall be charged from battery charging alternator provided

Suitable rating & type standard relays, contactors and other accessories for

automatic operation of diesel engine

g) Indication LED's for high / low lub, oil pressure, water temperature, engine

on indicator, with suitable alarms, acknowledgement button etc.

i) System Controller

j) Designing, Supply, Installation, Testing and Commissioning of system

controller to control operation of Main Electric Fire Pumps, Diesel Engine

Pump, Jockey Pumps, Terrace Pump in sequence as per specification

consisting of relays, timers, sensors, annunciation window for fault

indication, complete as per specification.

k) First Jockey pump will start than hydrant and sprinkler pump start, in case

of failure of power diesel pump will start.

Colour coded internal wiring and connections etc. with suitable size Fire

Retardant Low Smoke PVC insulated copper cable / solid aluminium strip /

bus bar from incoming to bus bar and from bus bar to switch gears / MCCB,

starters, meters, selector switches, indicating LED's, interlocking and

sequence operation arrangements.

l) Terminal facility for repeat indicator of various audio and visual indications.

m) First Jockey pump will start than hydrant and sprinkler pump start, in case

of failure of power diesel pump will start.

n) Colour coded internal wiring and connections etc. with suitable size Fire

Retardant Low Smoke PVC insulated copper cable / solid aluminium strip /

bus bar from incoming to bus bar and from bus bar to switch gears / MCCB,

starters, meters, selector switches, indicating LED's, interlocking and

sequence operation arrangements.

o) Terminal facility for repeat indicator of various audio and visual indications.

p) MR-5 Fire panel as above Set 1 269076.00 269076.00

6 AC ODU PANEL

Supplying, assembling, erecting, connecting, testing and commissioning of

dust, damp and vermin proof free floor standing factory built sheet steel

enclosed non-draw out modular type pressurization Panel outdoor type (IP-

54 Protection) fabricated out of 2.0 mm thick CRCA sheet hinged doors of

1.6mm thick CRCA sheet, duly painted complete with earth bus, aluminium

bus bar, numbering & sign writing, interconnection & including the cost of

connection through bus bar / copper conductor flexible connection with

necessary interlocking with existing panel as shown in drawing as per

specification and mounted with the followings.

Digitally signedPage

including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS

copper conductor S/C cable for voltage & current respectively, cable alleys,

cable gland plates in two half, etc. necessary metering protections &

indications etc. complete as required. ( Each starter should have remote

control and interlocking facilities including auto manual switch, NO/NC

contacts for automatic operation of fan in case of fire).

6.1 AC ODU PANEL-1 & 2 ,LOC- MID LEVEL/1ST FLOOR LEVEL

1 No. - 250 Amps Four Pole, 25 KA (ICU=ICS), MCCB with thermal magnetic

based release with o/c, s/c protection inbuilt E/F protection release all

indication, front operating hand & door interlock with shunt trip relay

1 No. Intelligent multi-function digital panel meter for recording V (Between

Phases and between each phase and neutral, A (In each phase and neutral),

KWHr with suitable rating CTs, CT shorting links.

1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup

2 / Class C SPD- surge protection device

TPN aluminium extensible type main bus bars of minimum of 300 Amp

capacity and auxiliary bus bar of suitable capacity with heat shrinkable

coloured sleeves and i/c DMC/SMC bus bars supports at required intervals

complete for cross section, size supports & their spacing etc.

All outgoing MCCB shall be provided with ON indication lamp with 2A SP

MCB for back up.

63A, FP, 300mA, ELCB manually operated - 10 Nos. (for ODU + spare)

40A, FP, 300mA, ELCB manually operated - 2 Nos. (for ODU + spare)

63A, FP, 10KA, MCB manually operated - 1 Nos.

40A, FP, 10KA, MCB manually operated - 1 Nos.

MR-6.1 Panel Described as above. Set 2 117733.00 235466.00

6.2 AC ODU PANEL-3,LOC- 1ST FLOOR LEVEL

1 No. - 250 Amps Four Pole, 25 KA (ICU=ICS), MCCB with thermal magnetic

based release with o/c, s/c protection inbuilt E/F protection release all

indication, front operating hand & door interlock with shunt trip relay

1 No. Intelligent multi-function digital panel meter for recording V (Between

Phases and between each phase and neutral, A (In each phase and neutral),

KWHr with suitable rating CTs, CT shorting links.

1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup

2 / Class C SPD- surge protection device

TPN aluminium extensible type main bus bars of minimum of 300 Amp

capacity and auxiliary bus bar of suitable capacity with heat shrinkable

coloured sleeves and i/c DMC/SMC bus bars supports at required intervals

complete for cross section, size supports & their spacing etc.

All outgoing MCCB shall be provided with ON indication lamp with 2A SP

MCB for back up.

63A, FP, 300mA, ELCB manually operated - 9 Nos. (for ODU + spare)

40A, FP, 300mA, ELCB manually operated - 9 Nos. (for ODU + spare)

Digitally signedPage

63A, FP, 10KA, MCB manually operated - 1 Nos.

40A, FP, 10KA, MCB manually operated - 1 Nos.

MR-6.2 Panel Described as above. Set 1 126389.00 126389.00

6.3 AHU PANEL -1 LHS

1 No. - 100 Amp. 25ka 4 pole Thermal release, MCCB (Ics=lcu) with O/L,

S/C & modular earth fault protection.

1 No. Intelligent multi-function digital panel meter for recording V (Between

Phases and between each phase and neutral, A (In each phase and neutral),

KWHr with suitable rating CTs, CT shorting links.

1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup

2 / Class C SPD- surge protection device

TPN aluminium bus bars of minimum of 125 A 25 kA capacity with heat

shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc.

(Following MCB (Ics=Icu upto 433 V) thermal magnetic release with over

current and short circuit releases, all indication, )

3 Nos. 63A 4P MCB 'C' 10 kA breaking capacity.

4 Nos. 40A 4P MCB 'C' 10 kA breaking capacity.

4 Nos. 25A 4P MCB 'C' 10 kA breaking capacity.

MR-6.3 Panel Described as above. Set 2 79837.00 159674.00

7 VENTILATION PANEL

Supplying, installation, testing and commissioning of dust, damp and vermin

proof free floor mounted, indoor type (IP-43 Protection) standing factory

built sheet steel enclosed modular construction extendable panel, suitable

for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system

fabricated out of suitable sized square tubular section and covered with

CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for

gland plates i/c cleaning & finishing complete with 7 tank process for powder

coating in approved shade, complete with Aluminium bus bars, inter-

connection with copper conductor wires / aluminium strips, neutral links,

earth bus etc. necessary metering protections & indications and mounted

with the following as per drawing and technical specifications attached etc.

complete as required. including control wiring, wiring for CO sensor etc. with

1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for

voltage & current respectively, cable alleys, cable gland plates in two half,

etc. necessary metering protections & indications etc. complete as required.

(Each starter should have remote control and interlocking facilities including

auto manual switch, NO/NC contacts for automatic operation of fan in case

The Panel should be IBMS compatible. (The starter should have auto manual

operation to take signal from fire panel for automatic operation of fan in

7.1 Ventilation PANEL for AUDITORIUM

1 No. - 100 Amp. 25ka 4 pole Thermal release, MCCB (Ics=lcu) with O/L,

S/C & modular earth fault protection.

1 No. Intelligent multi-function digital panel meter for recording V (Between

Phases and between each phase and neutral, A (In each phase and neutral),

KWHr with suitable rating CTs, CT shorting links.

1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup

2 / Class C SPD- surge protection device

Digitally signedPage

TPN aluminium bus bars of minimum of 125 A 25 kA capacity with heat

shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc.

(Following MCB (Ics=Icu upto 433 V) thermal magnetic release with over

current and short circuit releases, all indication, )

63 Amp. TP MCB, 10 kA with Fully automatic star delta starter suitable for

operating 11 KW motors/fan capacity, complete with contactors, overload

protection relay, current sensing type single phase preventor, ON/OFF

indications, push buttons, auto / manual / off selector switch, Digital

Ammeter with CT's and all other accessories with suitable rating PVC

insulated FRLS single core copper conductor cable etc. complete as required.

2 Nos. 63A 4P MCB 'C' 10 kA breaking capacity.

MR-7.1 Panel Described as above. Set 1 105684.00 105684.00

8.1 MR-8.1 32 Amp. TP MCB, 10 kA with Fully automatic star delta starter suitable for

operating 3.7 KW motors/fan capacity, complete with contactors, overload

protection relay, current sensing type single phase preventor, ON/OFF

indications, push buttons, auto / manual / off selector switch, Digital

Ammeter with CT's and all other accessories with suitable rating PVC

insulated FRLS single core copper conductor cable etc. complete as required.

8.2 MR-8.2 32 Amp. TP MCB, 10 kA with Fully automatic star delta starter suitable for

operating 2.2 KW motors/fan capacity, complete with contactors, overload

protection relay, current sensing type single phase preventor, ON/OFF

indications, push buttons, auto / manual / off selector switch, Digital

Ammeter with CT's and all other accessories with suitable rating PVC

insulated FRLS single core copper conductor cable etc. complete as required.

SUB HEAD - II - POINT WIRING

1 1.3.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface /

recessed steel conduit, with modular switch, modular plate, suitable GI box

and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc. as required. - Group C

2 1.54.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/

call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/ recessed steel

conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required.

3 1.5 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit alongwith 1

No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop

earthing as required. Metre 4607.5 433.00 460.41 2121334.01

4 1.6 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit alongwith 2

Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for

loop earthing as required. Metre 230 662.00 703.90 162162.02

Digitally signedPage

5 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in surface/

recessed steel conduit as required

6 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper

conductor, single core cable in the existing surface/ recessed steel/ PVC

conduit as required.

7 Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required Each 19 40.00 42.53 808.11

8 1.31 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6 amps

modular socket outlet and 5/6 amps modular switch, connection etc. as

9 1.32 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 amps modular socket outlet and 15/16 amps modular switch,

connection etc. as required. Each 97 586.00 623.09 60440.10

10 1.33 Supplying & fixing of 3 pin, 5 amp ceiling rose on the existing junction box/

wooden block including connection etc as required. Each 5 87.00 92.51 462.54

1.24 Supplying & fixing following modular switch/socket on the existing modular

plate & switch box including connections but excluding modular plate etc. as

1.27 Supplying & fixing following size/modules, GI box alongwith modular base &

cover plate for modular switches in recess etc. as required

12 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet,

with 2 pole and earth, metal enclosed plug top,alongwith 20 amps "C"

curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with

chained metal cover for the socket out let and complete with connections,

testing and commissioning etc. as required. Each 5 1621.00 1723.61 8618.05

13 2.19 Supplying and fixing 20 amps, 240 volts, TPN industrial type, socket outlet,

with 4 pole and earth, metal enclosed plug top,alongwith 20 amps "C"

curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with

chained metal cover for the socket out let and complete with connections,

testing and commissioning etc. as required. Each 2 2590.00 2753.95 5507.89

14 1.20 Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface conduit,

or cutting the wall and making good the same in case of recessed conduit as

required. (For ckt/submain wiring extra)

Digitally signed by

TOTAL CARRIED TO SUMMARY 9769764.77 0.00

SUB HEAD - III - (TELEPHONE / TV / DATA SYSTEM)

Supply, installation and commissioning of all conduiting, wiring and cabling

for MATV system including providing and fixing of:

a. All necessary specials and fittings/ brass bushes etc.

b. Approved cover plates for inspection, junction and outlet boxes.

c. 1.6 mm. thick outlet boxes and junction boxes.

d. All fixing accessories such as clips, nails, screws etc.

e. Providing and fixing approved saddles, hooks and grouting the same as

required, in case of all exposed conduit work.

f. Embedding conduits and accessories in wall, floors etc. during construction

and / or cutting chases and making good as necessary in the case of all

concealed conduit work.

g. Providing 14 SWG G.I. pull wire in all conduit work.

h. All splitter / tap off and amplifiers shall be suitable for interactive system

and shall be bi-directional.

1 1.24 Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular

plate etc. as required.

1.1 1.24.6 Telephone socket outlet Each 6 148.00 157.37 944.21

1.2 1.24.7 TV antenna socket outlet Each 2 148.00 157.37 314.74

2 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base

& cover plate for modular switches in recess etc as required.

3 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated

annealed copper conductor, unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as required.

4 1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and protected

with PVC sheath in the existing surface/ recessed steel/ PVC conduit as

required Metre 95 47.00 49.98 4747.63

5 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V,

complete as required Each 5 99.00 105.27 526.33

6 1.53 Supplying and drawing of UTP 4 pair CAT 6A LAN Cable in the existing

surface/ recessed steel/ PVC conduit as required.

7 1.20 Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface conduit,

or cutting the wall and making good the same in case of recessed conduit as

required. (For tel./ TV / Data wiring)

Digitally signed by

8 M.R.-8 Supplying, Installation, testing and commissioning of following sizes of 0.5

mm dia annealed tinned copper conductor PVC insulated and PVC sheathed

unarmoured telephone cable on surface/ existing cable tray complete as

9 M.R.-9 Supplying and fixing modular type Information Outlet RJ -45, CAT 6 Data ,

front plate and suitable size metal box on surface or in recess including

connections etc.complete as required. Each 10 360.00 3600.00

10 Supplying and drawing co-axial TV cable following grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper braid and

protected with PVC sheath in the existing surface/ recessed steel/ PVC

conduit as required.

11 M.R.-11 Supplying, erection, testing and commissioning of following tap off / splitter

as per specification in 1.6 mm thick CRCA sheet steel enclosure for CATV

11.1 M.R.-11.1 4 Way splitter box Each 1 403.00 403.00

12 1.24 Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular

plate etc. as required.

Note:- All Data, TV and Telephone will be FTH based.

SUB HEAD - IV - DISTRIBUTION BOARD/ RACEWAYS

1 2.3 Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

2 2.4 Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But

MCB/RCCB/Isolator)

3 2.5 Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly

powder painted, inclusive of 200 A tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCBs (but without MCBs and incomer )

as required . (Note : Vertical type MCB TPDB is normally used where 3

phase outlets are required

4 2.13 Supplying and fixing following rating, four pole, 415 V, isolator

in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Digitally signed by

5 2.14 Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

sensitivity current 30 milli amperes in the existing MCB DB complete with

connections, testing and

commissioning etc. as required.

6 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning etc.

6.2 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required. Nos. 15 13.00 13.82 207.34

7 Supply, assembly and laying of ceiling mounted suspeneded raceway

made out of 1.6mm thick GI sheet complete with bends, junction box,

covers etc. complete with all other accessories duly suspended from the

ceiling with G.I. suspenders including fabrication etc. complete in all

respect as required.

SUB HEAD - V - LIGHT FIXTURES AND FANS

1 Supply Installation, testing and commissioning of following fittings/

luminaires/ ceiling fans complete with necessary starter/s & copper wound/

electronic ballasts, capacitors, lamps, louvers & all other accessories, down

rods of suitable length, connections with 1.5 sq.mm. PVC insulated FRLS,

copper conductor, single core cable including loop earthing with 1.5 sq mm

FRLS PVC insulated copper conductor, single core cable etc. complete as

1.1 MR-1.1 COB based recessed downlight luminaire , System power: 12W, Luminous

flux of luminaire 1800 lm, Colour temperature of 4000 K, Neutral

white,CRI>90, THD<5%, P.F>0.9, SDCM<3, UGR<16, 230 V constant

current driver, 70% of luminous flux after 50,000 operating hours; Energy-

efficient COB, Direct light emission, Luminaire housing in aluminium,

Polyester powder white coloured coat applied over a 5-stage pre-treatment,

Lens with anti glare reflector and a beam angle of 55°, ZHLS (ZERO

HALOGEN LOW SMOKE) wiring,Electronic control gear,

Protection class II, IP 40,

1.2 MR-1.2 COB based recessed downlight luminaire, System power: 20W, Luminous

flux of luminaire 1800 lm, Colour temperature of 4000 K, Neutral white,

CRI>90, THD<7%, P.F>0.9, SDCM<3, UGR<16, 230 V constant current

driver, 70% of luminous flux after 50,000 operating hours; Energy-efficient

COB, Direct light emission, Luminaire housing in aluminium, Polyester

powder white coloured coat applied over a 5-stage pre-treatment, Lens with

anti glare reflector and a beam angle of 55°, ZHLS (ZERO HALOGEN

LOW SMOKE) wiring, Dali control gear.

Protection class II, IP 40,

Digitally signed by

1.3 MR-1.3 COB based pendant downlight luminaire with system power: 35 W,

Luminous flux of luminaire 3150 lm, Colour temperature of 4000 K,

Neutral white, CRI>90, THD<10%, P.F>0.9, SDCM<3, UGR<16, 230 V

constant current driver, 70% of luminous flux after 50,000 operating hours;

Energy efficient LEDs, Direct light emission, Luminaire housing in

aluminium, Polyester powder black coloured coat applied over a 5- stage pre-

treatment, with beam angle of 36°, ZHLS (ZERO HALOGEN LOW SMOKE)

internal wiring, Electronic control gear,

Protection class I, IP 20,

1.4 MR-1.4 Modular pendant luminaire with HPE (High-Performance Efficiency) LED

(Light Emitting Diode) system power: 22 W Luminous flux of luminaire

2200 lm, Colour temperature of 4000 K, Neutral white, CRI>90,

THD<10%, P.F>0.9, SDCM<3, 230 V constant current driver, 70% of

luminous flux after 50,000 operating hours; Energy efficient LEDs, Direct

light emission, Luminaire profile in aluminium, polyester powder white

coated, pre-wired batten luminaire, snap-fit prismatic diffuser for

homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE)

internal wiring, Electronic control gear, Sliding fixing wire suspension,

Protection class I, IP 40,MacAdam 3,

1.5 MR-1.5 Customized Pendant luminaire with HE-High Efficiency LED (Light Emitting

Diode) system power: 28W/m, the luminous flux of luminaire 2240 lm/m,

color temperature of 4000 K, Neutral white,CRI>90, THD<10%, P.F>0.9,

SDCM<3, 230 V constant current driver, 70% of luminous flux after 50,000

operating hours, direct/indirect light emission, Luminaire profile in

aluminum, Black powder-coated, With opal diffuser for uniform

illumination, Electronic control gear.

Protection class I, IP20, Macadam 3,

1.6 MR-1.6 LED recessed luminaire with LED(Light Emitting Diode) system power:

32W, colour temperature of 4000K, 230V constant current driver, 70% of

luminous flux after 50,000 operating hours, energy efficient LEDs, CRI>90,

THD<10%, P.F>0.9, SDCM<3, luminous flux of 3200 lm,direct light

emission, Aluminium Extruded body, polyester white powder coat applied

over a 5-stage pre-treatment, Opal diffuser for glare-free uniform light,

electronic control gear, Protection class I, IP40, MacAdam 3, T.H.D≤

10%, driver efficiency ≥ 88%, surge protection of 2.5kV,

1.7 MR-1.7 Pendant luminaire with HPE (High Performance Efficiency) LED (Light

Emitting Diode) system power: 25 W, Luminous flux of luminaire 2000 lm,

Colour temperature of 4000 K, Neutral white, CRI>90, THD<10%,

P.F>0.9, SDCM<3, 230 V constant current driver, 70% of luminous flux

after 50,000 operating hours; Energy efficient LEDs, Direct light emission,

Luminaire profile in aluminium, Polyester powder black coloured coat applied

over a 5- stage pre-treatment, Prismatic diffuser for a homogenous light

distribution, ZHLS (ZERO HALOGEN LOW SMOKE) internal wiring,

Electronic control gear,

Protection class I, IP20,

Digitally signed by

1.8 MR-1.8 Pendant luminaire with HPE (High Performance Efficiency) LED (Light

Emitting Diode) system power: 45 W, Luminous flux of luminaire 3600 lm,

Colour temperature of 4000 K, Neutral white,CRI>90, THD<10%, P.F>0.9,

SDCM<3, 230 V constant current driver, 70% of luminous flux after 50,000

operating hours; Energy efficient LEDs, Direct light emission, Luminaire

profile in aluminium, Polyester powder black coloured coat applied over a 5-

stage pre-treatment, Prismatic diffuser for a homogenous light

distribution, ZHLS (ZERO HALOGEN LOW SMOKE) internal wiring,

Electronic control gear,

Protection class I, IP20,

1.9 MR-1.9 Ø = 980 Mounted

Surface mm, W = luminaire

HPE PL =Performance

(High 1500 mm Efficiency) LED

(Light Emitting Diode), system power: 35 W, Luminous flux of luminaire

3150 lm, colour temperature of 4000 K, Neutral white, CRI>90,

THD<10%, P.F>0.9, SDCM<3, 230V constant current driver, 70% of

luminous flux after 50,000 operating hours, Energy efficient LEDs, Direct

light emission, Luminaire housing in aluminium, Polyester powder black

coloured coat applied over a 5- stage pre - treatment, Prismatic diffuser

for a homogenous light distribution ZHLS (ZERO HALOGEN LOW SMOKE)

internal wiring, integral electronic control gear

Protection class I, IP 20

1.10 MR-1.10 Recessed spotlight luminaire with LED (Light Emitting Diode) system power:

10 W, Luminous flux of luminaire 700 lm, Colour temperature of 4000 K,

Neutral white, CRI>90, THD<5%, P.F>0.9, SDCM<3, 230 V constant

current driver, 70% of luminous flux after 50,000 operating hours; Energy

efficient LEDs, Direct light emission, Luminaire profile in aluminium,

Polyester powder black coloured coat applied over a 5- stage pre-treatment,

Clear glass cover with reflectors and beam angle of 45 degrees, ZHLS

(ZERO HALOGEN LOW SMOKE) internal wiring, Electronic control gear,

Protection class II, IP 20,

1.11 MR-1.11 Track mounted spotlight with COB, system power:15W, luminous flux of

luminaire 1350lm, colour temperature of 4000K, neutral white, CRI>90,

THD<10%, P.F>0.9, SDCM<3, constant current driver, direct light

emission, clear acrylic diffuser, 38º beam angle, housing in die-cast

aluminium, polyester black powder coat applied over a 5-stage pre-

treatment, flexible light body structure can be rotated and adjusted in

horizontal and vertical direction, integral electronic control gear

Protection Class II, IP20

1.12 MR-1.12 Non LED Track Singel Phase, Wall / Surface / Ceiling Mounted, Black

Profile Without Luminary elements

Digitally signed by

1.13 MR-1.13 Recessed downlight with HPE (High-Performance Efficiency) with LED (Light

Emitting Diode), system power: 12 W, Luminous flux of luminaire 1020 lm,

Colour temperature of 4000 K, Neutral white, CRI>90, THD<5%,

P.F>0.9, SDCM<3, 230V constant current driver, 70% of luminous flux

after 50,000 operating hours; energy-efficient LEDs, direct light emission,

housing in die-cast aluminium, Polyester powder white coloured coat applied

over a 5-stage pre-treatment trim, prismatic diffuser for homogenous light

distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, electronic

control gear,Protection class II, IP 20,

1.14 MR-1.14 2 DALI Controller, 2 wall mounted control and other accessories for

auditorium Nos. 1 242248.00 242248.00

1.15 1.41 Installation, testing and commissioning of pre-wired, fluorescent fitting /

compact fluorescent fitting of all types, complete with all accessories and

tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq.

mm FRLS PVC insulated, copper conductor, single core cable and earthing

2 19.1 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5

star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle

kit, safety rope, copper winding, Power Factor not less than 0.9, Service

Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350

RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or

electronic regulator unit for speed control and all remaining accessories

including safety pin, nut bolts, washers, temperature rise=75 degree C

(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50

Hz, single phase AC Supply earthing etc complete as required Nos. 14 2730.00 2902.81 41365.03

3.0 MR-3 Supply of Exhaust fan complete with louver and plug top with 3 core flexible

wire as required upto socket/ ceiling boxes as required, complete with

cutting of wall, grouting of fan and making good of the wall.

300 mm SWEEP EXHAUST FAN (1400 RPM)

4 MR-4 Supplying, Installation, testing and commissioning of 450 mm dia wall

bracket fan complete in all respect as required. Each 5 3982.00 19910.00

5 1.25 Supplying and fixing two module stepped type electronic fan regulator on

the existing modular plate switch box including connections but excluding

modular plate etc. as required Each 14 369.00 392.36 5311.54

6 1.44 Installation, testing and commissioning of ceiling fan, including wiring the

down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC

insulated, copper conductor, single core cable etc. as required.

7 1.50 Installation of exhaust fan in the existing opening, including making good

the damage, connection, testing, commissioning etc. as required.

8 1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan

SUB HEAD - VI - LIGHTENING PROTECTION SYSTEM

LIGHTNING PROTECTION AS PER IEC 62305 /NBC 2016

Digitally signed by

1 SITC of single spike air terminals of 10 mm dia. & 1000 mm length as

required and as per site conditions. The air terminal shall be manufactured

MR-1 with aluminium & shall be as per IEC 62561-2. The air terminal shall be

fixed on SS sloted Z-clamp.

2 SITC of single spike air terminals of 10 mm dia. & 1000 mm length as

required and as per site conditions. The air terminal shall be manufactured

MR-2 with aluminium & shall be as per IEC 62561-2. The air terminal shall be

fixed with necesarry arrangement(MV Clamp) .

3 SITC of single spike Angled air terminals of 10 mm dia. & 600 mm

length and 400mm leg length as required and as per site conditions. The

MR-3 air terminal shall be manufactured with aluminium & shall be as per IEC

4 SITC of single spike air terminals of 10 mm dia. & 1000 mm length as

required and as per site conditions. The air terminal shall be manufactured

MR-4 with aluminium & shall be as per IEC 62561-2. and The Air terminal shall be

fixzed with Antenna pipe Clamp(Hose Clamp).

5 SITC Roof Conductor for Parapet & Mesh : Supply of 8 mm dia

aluminium round conductor for air termination network at parapet and for

MR-5 making mesh at terrace level and shall meet the requirement of IEC 62561-

6 SITC of Parapet Conductor holder for holding of 8 mm dia. round

conductor (for RCC roof). The conductor holder shall be mounted on plastic

MR-6 base support and shall meet the requirements of IEC 62561-4.It should be

installed at every 1 mtr.

7 SITC of parapet & mesh conductor holder for holding 8 mm dia. round

conductor (For metallic sheet). The conductor holder should be installed at

MR-7 every 1 mtr. The conductor holder shall be made with SS Z type metal shed

holder & as per IEC 62561-4.

8 MR-8 SITC of Cartridge (Glue) Nos. 11 5669.00 62359.00

9 MR-9 SITC of Dispenser for Cartridge Nos. 1 9157.00 9157.00

10 SITC of Expansion piece made of 8mm dia. Aluminium & as per IEC 62561-

2 along with suitable connecting accessory. It shall be installed at every 20

MR-10 mtr to maintain the flexibility to the conductor due to heat.

11 SITC of Universal Connector for making straight, Tee & Cross joint of 8

MR-11 mm Aluminium Conductor to 8 mm dia Aluminium conductor on parapet

wall, roof and vertical facade of masonery / glass / metallic work.

2 Down Conductor :

2.1 MR-2.1 SITC of 8 mm dia aluminium round conductor for Down conductors to be

installed on vertical wall, façade of masonary / glass / metalic work. It shall

meet the requirements of IEC 62561-2.

2.2 MR-2.2 SITC of Wall Conductor holder for holding 8 mm dia. round conductor (for

RCC wall). The conductor holder should be installed at every 1 mtr. The

conductor holder shall be made with clamp mounted on plastic base support

& as per IEC 62561-4.

2.3 MR-2.3 SITCof Universal Connector for making straight joint of 8 mm AL Round

Conductor to 8 mm dia AL Round conductor. Nos. 6 218.00 1308.00

2.4 MR-2.4 SITC of Test Clamp to disconnect the down conductor from the earth

termination network for regular checks of the earth termination resistance

value. (with enclosure). It shall meet the requirements of IEC 62561-2.

Digitally signed by

2.5 MR-2.5 SITC of Lightning Strike counter Model: JMV 7D for counting the number

of lightning strikes without any power supply. The Counter should be

mounted on the Down Conductor. The Lightning Counter should be IP 68

rated enclosure suitable for external application.

3.0 Earth Termination Network:

3.1 MR-3.1 SITC of Earthing termination made of copper-bonded rod of 10 feet

length,17 mm dia. (Minimum copper bonding shall be 0.25mm) as per IS

3043, IEEE-80, NBC 2016 along with Earth enhancement material some

with resistivity of 0.12 ohm-mtr, and complying IEC 62561-7 and Eco guard

Pit Cover complying IEC 62561-5 and other accessories as required and as

per specification and other applicable codes.

3.2 MR-3.2 SITC of 8 mm CBS Conductor laid at below the ground, as Required and as

per specification and code of practice with straight or T- joints.

TOTAL 576973.30

SUB HEAD - VII - Solar

1 MR-1 SITC of Solar Panels: 7 KWp (DC Output)

Supply and Installation of 330Wp X 22 No’s Poly Crystalline

7 KWp Solar inverter (3 Phase)

Design, Supply, Installation, Testing and Commissioning of turnkey

project including following works:

- Complete Mechanical & Electrical works

- Module mounting structure for RCC roof.

- DC Cables – Polycab / Havel’s / finolex

- Earthling for Solar Structure and Inverter at Nearest Point as discussed.

- Balance of System (BOS): ACDB Box, DCDB Box Conducting material,

Switches, clips, fasteners etc. as per actual. Set 1 322358.00 322358.00

SECTION - VIII - (CABLES, CABLE TRAY)

CABLES & CABLE TRAY

1 Supply of following size of 1.1 kv grade FRLS multicore aluminium / copper

conductor XLPE insulated and PVC sheathed armoured cable as per IS:

7098:1988 (Part-I) with upto date amendments.

2 MR-2 Supply, laying, testing & commisioning of LPCB/BRE/TUV approved Fire

Survival armoured cable as per BS 7846, fire Test as per BS 6387 CWZ,

copper conductor /mica taped/ Flame Barrier/ Cross Linked Insulation/

Halogen Free Inner Sheath/ SWA/ Halogen Free Outer Sheath (1000V),

LPCB/BRE/TUV Certified for power cables. etc. complete as required.

(Tagging to be provided with aluminium strips on both the ends as

Digitally signed by

3 7.8 Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE

power cable of 1.1 KV grade of following size on cable tray as required.

3.1 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Mtr 2094 44.00 46.79 97958.85

3.2 7.8.2 Above 35 sq. mm and upto 95 sq.mm (clamped with 25x3mm MS flat

3.3 7.8.3 Above 95 sq. mm and upto 185 sq.mm (clamped with 25/40x3mm MS flat

3.4 7.8.4 Above 185 sq. mm and upto 400 sq.mm (clamped with 40x3mm MS flat

4 9.1 Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

5 Supply, installation, testing & commisioning of cable termination of above

cables with copper lugs & flameproof brass compression glands on both the

ends with inhibting compound etc. complete as required.

6 Supply, laying, testing & commissioning of the following size of 1.1KV grade

PVC insulated and PVC sheathed copper conductor armoured stranded

control cable including termination on existing cable trays /existing trench,

walls including the cost of saddles, gutties, clamps, lugs, brass,

compression, glands etc. confirming to latest IS complete as required,

7 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised

Iron cable tray (Galvanisation thickness not less than 50 microns) with

perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G.I. suspenders including G.I.

bolts & nuts, etc. as required

7.1 4.6.1 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. Mtr. 332.5 669.00 711.35 236523.11

7.2 4.6.2 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. Mtr. 190 716.00 761.32 144651.33

7.3 4.6.4 300 mm. Width x 50mm. Depth x 1.6 mm. Thickness. Mtr. 76 963.00 1023.96 77820.80

7.4 4.6.6 450 mm. Width x 50mm. Depth x 2.0 mm. thickness. Mtr. 47.5 1325.00 1408.87 66921.44

8 4.7 Supplying and installing following size of perforated Hot Dipped Galvanised

Iron cable tray "bends" (galvanisation not less than 50 microns) with

perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G.I. suspenders including G.I.

bolts & nuts, etc. as required.

8.1 4.7.1 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. Each 6 1159.00 1232.36 7394.19

Digitally signed by

8.2 4.7.2 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. Each 4 1270.00 1350.39 5401.56

8.3 4.7.4 300 mm. Width x 50mm. Depth x 1.6 mm. Thickness. Each 2 1852.00 1969.23 3938.46

8.4 4.7.6 450 mm. Width x 50mm. Depth x 2.0 mm. thickness. Each 2 2683.00 2852.83 5705.67

8.5 4.7.11 600 mm. Width x 62.5mm. Depth x 2.0 mm. thickness. Each 2 3732.00 3968.24 7936.47

9 4.8 Supplying and installing following size of perforated Hot Dipped Galvanised

Iron cable tray "Tee" (galvanisation not less than 50 microns) with

perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G.I. suspenders including G.I.

bolts & nuts, etc. as required

9.1 4.8.1 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. Each 4 1327.00 1411.00 5644.00

9.2 4.8.2 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. Each 2 1383.00 1470.54 2941.09

9.3 4.8.4 300 mm. Width x 50mm. Depth x 1.6 mm. Thickness. Each 1 2156.00 2292.47 2292.47

9.4 4.8.6 450 mm. Width x 50mm. Depth x 2.0 mm. thickness. Each 1 3141.00 3339.83 3339.83

9.5 4.8.11 600 mm. Width x 62.5mm. Depth x 2.0 mm. thickness. Each 1 4802.00 5105.97 5105.97

SUB HEAD - IX - CHEMICAL EARTHING

1 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/

coke and salt as required.

2 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/

coke and salt as required.

3 MR-3 Providing and fixing 50 mm X 6 mm size of G.I. strip in 80 mm dia 'B' class

G.I. pipe from earth electrode as required Mtr. 19 815.00 15485.00

4 MR-4 Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for

connections etc, as required Mtr. 523 307.00 160407.50

5 5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground

as strip earth electrode, including connection/ terminating with G.I. nut,

bolt, spring, washer etc. as required. (Jointing shall be done by overlapping

and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

6 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. Pipe

FRLSom earth electrode including connection with G.I. nut, bolt, spring,

washer excavation and re-filling etc. as required. Mtr. 48 706.00 750.69 35657.77

7 MR-7 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. Pipe

FRLSom earth electrode including connection with G.I. nut, bolt, spring,

washer excavation and re-filling etc. as required. Mtr. 10 384.00 3840.00

8 5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

earthing along with existing surface/ recessed conduit/ submain wiring/

cable as required. Mtrs. 333 42.00 44.66 14848.98

Digitally signed by

9 Supply and fixing of following GI strip/ wire including all necessary fixing

accessories and effecting connections as required & approved by the

Engineer Incharge.

9.3 MR-9.3 25 x 3 mm cupper strip Mtr. 29 624.00 17784.00

SUBHEAD - X : AUTOMATIC GAS BASED PANEL PROTECTION

LT panel, Lift Panel, Server Room/UPS Room etc.

1 MR-1 Supplying, installing, testing and commissioning of 2kg capacity Novec

1230/ (FK-5-1-12) , DLP Assembly with automatic valve, push in connector

for tube, Novec 1230/NAF S 1230 , mounting bracket, End

of Line adopter and low pressure switch for monitoring system activation

2 MR-2 Supplying, installing, testing and commissioning of 4kg capacity Novec

1230/ (FK-5-1-12) , DLP Assembly with automatic valve, push in connector

for tube, Novec 1230/NAF S 1230 , mounting bracket, End

of Line adopter and low pressure switch for monitoring system activation.

3 MR-3 Supplying, installing, testing and commissioning of UL Certified Linear

pneumatic Heat Detection Tube for automatic fire detection & supperession

system made by special modified polyamaide (PA), colour red RAL300, burst

temperature 1000C to 1400C, inner diameter 4mm, outer diameter 6mm.

Pressurised with dry nitrogen at 15 bar pressure with all necessary fittings &

supports (UL Listed).

4 MR-4 Supplying, installing, testing and commissioning of Master Control Unit with

audio visual alarm Control Panel (IP54 third party rating), 2 NO/NC potential

free relay contact for Main Fire Alarm/BMS/SCADA Integration. Gas

discharge led indicator, battery led indicator, system status Led indicator,

AC power ON Led indicator Nos 8 5263.00 42104.00

TOTAL 955131.50

SECTION - XI - SAFETY EQUIPMENTS & MISCELLANEOUS

1 MR-1 Supply and fixing in position 1000mm wide checkered rubber matting of

1.1KV grade as per electricity rules,with thickness not less than 12mm.

2 2.21 Providing and fixing M.V. Danger Notice plate of 200mm x 150mm,made of

mild steel atleast 2mm thick and vitreous enamelled, white on both sides

and with inscription in signal red colour on front side written in English &

Hindi as required. Nos. 6 269.00 286.03 1716.17

3 MR-3 Supply and fixing in position the approved shock treatment / restoration

charts written in Hindi and English duly framed in teak wood frame and

covered with 2.8mm glass as required. Nos 4 1209.00 4836.00

4 Supply,Installation,Testing and Commissioning of following size of FRLS PVC

insulated armoured copper contol cable.

5 MR-5 Providing and fixing ABC Dry Powder Fire Extinguisher 4 Kg capacity mfd to

IS: 15683 with BIS mark, Brass forged squeeze lever discharge valve, fitted

with pressure indicating gauge with discharge hose & well design

ALUMINIUM discharge nozzle, duly charged with ISI Marked MONO

AMONIUM PHOSPHATE (MAP) SILICONISED powder and pressurized with

Nitrogen Gas. CE MARKED. Wall mounting bracket with screw complete as

Digitally signed by

6 MR-6 Providing and fixing fire extinguisher of Co2 type Fire Extinguisher 4.5kg

capacity with Brass forged Screw down / squeeze lever type valve, initial

gas charged as per IS 15222, rubber braided discharge hose & Horn,

complete with accessory as per IS:15683 with BIS mark , MTC & PESO (OLD

CCOE ) certificate. Wll mounting bracket with screw complete as required.

7 MR-7 Supplying and fixing of MS pedestal stand suitable for supporting four

buckets as required. Nos 2 1103.00 2206.00

8 MR-8 Supplying and fixing First Aid Box of 18 S.W.G. M.S sheet,painted as

approved & prescribed by Indian Red Cross Society & as per attached

specifications. Sets 2 2063.00 4126.00

9 MR-9 Supplying and fixing of caution Boards of 16 S.W.G. , M.S. sheet of 300 mm

x 150mm size, duly painted & having "MAN ON LINE' & "DO NOT SWITCH

ON' written in Red complete with hanging arrangement as required.

10 MR-10 Supply and fixing in position the approved single line diagram framed in

1000 x 800 mm size glass framed and installed in main switch room.

11 MR-11 Supply of tool kit with 1 pair,1.1KV rubber hand gloves of aproved make.

12 MR-12 Providing, laying and fixing following dia G.I. pipe (medium class) in ground

complete with G.I. fittings

13 14.14 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in

ground complete with RCC collars, jointing with cement mortar 1:2 (1

cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as

14 14.15 Supply & laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, band, couplers etc.confirming to IS 14930, Part II

complete with fitting and cutting, joointing etc. in the existing trench,

complete are required.

SECTION - XII - UPS

1 Supply, Installation, Testing and Commissioning of IGBT based PWM

technology UPS system of following ratings with computer communication

possibilities consisting of standard software, double conversion system

suitable for providing power supply to computers/servers sports lighting,

corridor lighting delivery atleast 30 minutes backup, suitable for incoming

415 volts, 3phase +15% -15%, 50Hz supply and three phase output

voltage, including, rectifier/dual converter, bypass switch, Manual By-pass,

Inbuilt Galvanic isolation transformer (before static switch), ECO mode,

inverter, filter. Bypass & static transfer switch for automatic switch over,

providing static bypass module, SCR switching, high switching frequency

microprocessor based with built-in technical protections like short circuits,

over load, high / low voltage cut off protection of load from source inclusive

of bypass facility without giving any break of power, maintenance bypass

switch. The UPS should have IGBT based rectifier and IGBT based

inverter.The UPS shall be provided with inbuilt Isolation transfomrer. The

UPS should also give minimum 94% efficiency at 100% load.

Digitally signed by

Microprocessor/ software controlled annunciation, protection (including

against input phase reversal), and menu run diagnostic module, associated

cabling, connections, termination, erection including associated foundation/

masonry or RCC work for mounting on base channels etc. complete as

required and as per specifications.

Providing & Fixing of configuration complete with maintenance-free sealed

battery (SMF VRLA Type) banks and BCB consisting of (……..AH x 2V x

…..Nos.) Cells SMF Type suitable for UPS System for 30 mins backup for

individual UPS.

Note:- Please also attach battery back up calculation alongwith quotation.

MR-1 30 KVA UPS with 30 min battery back up of 3 phase input & 3 phase

SUB-HEAD - XIII - EXTERNAL LIGHTING

1 External Lighting

1.1 MR-1.1 SITC of 25W LED Postop made up of aluminium pressure die-cast aluminum

with integrated pole top with polyester powder coating in addition to a

specific weathering resistance treatment, color RAL7011.Non-yellowing

transparent and textured Polycarbonate UV-protected round symmetrical

diffuser 1.5 mm thick with circular radial pattern for glare-free and even

light distribution. The fixture should have provision of simplified

extraordinary maintence by an easy to remove top openable driver

compartment. High Efficiency long life LED module with SMD LED package

mounted on MCPCB. Lumen Efficacy of LED>105Lm/W@ 3000K color

temperature and CRI >70. Powered by Built In electronic. LED driver with

THD<10%, 4kV inbuilt surge protection, high cut off at 325V, auto-restart

etc. Suitable for pole mounting having OD of 60 mm and height of 6 meters.

Fixture Lumen>2700 Lm, IP 66(no glue), IK 10, PF>0.95, Operating

voltage range: 120 V - 277 V Average life L70B50: 50000 hours. Luminaire

manufacture shall provide LM79 report & LM80 report . Both the fixture and

Driver should be of same make & must have separate BIS approval.

1.2 MR-1.2 SITC of Smartbright Led Street light made up of pressure die cast

aluminium housing with LM06 alloy and polycarbonate cover with high

impact resistance along with integrated optics.Suitable for pole dia mounting

up to 60mm.Higher ingress protection IP66 and impact resistance of

IK07.Wattge-45W with maximum lumen output >5400lm.Philips logo

embossed on housing top cover. Operating voltage range: 140-270V/50Hz,

Average life L70B50: 50000 hours, High efficiency long life high power LED

module with SMD, LED package mounted on MCPCB. Lumen efficacy of LED

>120 lm/W, Powered by built-in potted LED driver gives constant light over

wide volatage range with Surge Voltage protection 4 kV, CRI- 70, CCT-

5700K, dimensions: 473mm x 165mm x 80mm,power factor ≥0.9.The

driver should be BIS approved, fully potted and encapsulated .The fixture

should comply with the parameters as per IS10322. The LED driver should

comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13,

2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety,

IEC62384 ed.1.1, 2011 forperformance and IEC61547 ed.2.0, 2009, .LM 79

and LM80 reports need to be submitted from a NABL/UL accredited lab to

verify above parameters. Nos. 10 3517.00 35170.00

Digitally signed by

1.3 MR-1.3 SITC of Architectural bollard LED made up of pressure die cast aluminium

housing with LM06 alloy and symmetric optics with polycarbonate

diffuser.Wattage 8.5W with lumen output of 500lm and system efficacy of

60lm/W,Operating voltage range: 140-270V/50Hz, Average life L70B50:

50000 hours, High efficiency long life high power LED module with SMD,

LED package mounted on MCPCB. CRI>70, CCT-6500K,Power factor

≥0.95.Higher ingress protection IP65 and impact resistance of IK10

dimensions: 177mm x 215mm x 700mm, .IEC 60598 Certified.

Manufacturer shall have inhouse lab approved by NABL or ministry of

science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters. Nos. 10 7522.00 75220.00

1.4 MR-1.4 SITC of Spike mounted LED fixture made up of Die - Cast aluminium

housing with electrostatic powder coating & high quality temper glass with

precise PMMA optics for light distribution . Ground mounting spike made of

die cast aluminum. Electrostatic powder coated. This luminaire contains built-

in LED modules.Wattage- 8W with system efficacy of 475-550lm. Beam

Angle: 20°/45°, inbuilt Electronic driver ON/OFF CE/CB, IP rating IP65,

Mechanical resistance IK06. Dimension Ø60 mm x 80 mm x 98.5 mm.

Operating ambient temperature range is from -40°C to +50°C. Operating

voltage range of 100-240VAC. working humidity upto 95%. LM 79 and LM80

reports need to be submitted . Both the fixture and Driver should have

separate BIS approval. Nos. 10 2544.00 25440.00

1.5 MR-1.5 SITC of Specially designed step light LED 3000K 220-240Vac CRI > 80 Input

power: 2-3W Dimension 145mm x 145mm x 103mm Electronic driver

ON/OFF CE mark. IP rating IP67 and impact resistance IK08. MATERIAL

CHARACTERISTICS mtal and plastic housing with polycarbonate UV-resistant

optical cover, aluminum and white color. Operating ambient temperature

range is from -20°C to +40°C.

1.6 MR-1.6 SITC of 6m octagonal Pole with single arm. Material for pole section: Hot

rolled product of non alloy structural steel grade S355, Other parts: MS as

per IS 2062. Material as per BS EN 10025 equivalant to Indian standard..

Bottom (O.A.F.) 130mm and top (O.A.F.) 70mm. Size of Base Plate: 220 SQ,