PROVN OF RCC RETAINING WALL AT SHANKAR VIHAR INTEGRATED SPORTS COMPLEX AND CERTAIN MINOR WORKS UNDER AGE B/R-I, B/R-II AND AGE E/M OF GE (SOUTH) DELHI CANTT-10

Amount

Excavation in trenches n.exc 1.5m in depth and 1.5m in width and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and as directed.

Removing excavated material (soil) n.exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and as directed.

M&L for providing cement concrete 1:4:8, type D-2, using 40mm graded stone agg in foundation, mass concrete and filiings complete all as specified and as directed.

M&L for form work to side of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and simillar work complete all as specified and as directed.

M&L for providing reinforcement cement concrete 1:2:4 (Nominal Mix) as in Beams, cantilevers, ressummers, lintels over 1.5m span concrete etc. complete all as specified and as directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F mild steel TMT bars 8 to 10 mm dia a as in stirrups, spacers and binders complete all as specified and as directed.

M&L for brick work with sub class B old size burnt bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L for brick work with sub class B old size burnt bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specified and as directed. Note : WPC will be measured & paid separately.

Supply only Liquid water proofing compound of approved quality.

M&L for preparation of new plaster surfaces apply two coat of cement base paint over a coat of primer complete all as specified and as directed.

M&L for hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection/path complete all as specified and as directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors finished even complete all as specified and as directed.

M&L for providing 25mm thick cement concrete 1:2:4 type B1 (Using 20mm graded stone agg) , as in sub base in floor/paving etc complete all as specified and as directed.

M&L for Vetrified Ceramic tiles, light shade, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. laid over 15mm thick cement mortar screed bed of CM (1:6) , set and jointed in neat cement slurry @ 3.00 kg per Sqm and pointed in white or coloured cement to match the shade of tile, complete all as specified and as directed.

M&L for Vetrified Ceramic tiles, light shade, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. over 10 mm thick CM (1:4), set and jointed in neat cement slurry @ 3.00 kg per Sqm and pointed in white or coloured cement to match the shade of tile complete all as specified and as directed.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

S&F pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

S&F 35 mm thick Factory made 2nd class hardwood plain,framed paneled shutters(any numbe of panels) with lock rail and panel of 9mm BWP commercial ply with commercial veneering on both faces size of rail and stile as per IS-1003(part) Kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35 mm thick factory made 2nd class Hard wood glazed and Skelton shutters (three panels) open rebated and prepared to receive and including wiremesh/glass/gauge etc with all accessory as required and divided into squares edges of framing Plain, chamfered or rounded mitered and rebated sash bar any number with cut or mitered beads for securing glass/gauge etc Size of members of shutters complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for Poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section(two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified and as directed. Note:- Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S&F providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws etc. as per architectural drawings and complete all as specified and as directed.

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paidfor separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws allcomplete as per architectural drawings and complete all as specified and as directed.

S&F stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section etc. complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 200mm long etc. complete all as specified and as directed.

S&F Stainless steel of AE SI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F magic eye and fixed to doors complete all as specified and as directed.

S&F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified and as directed.

S&F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60mm complete all as specified and as directed.

M&L for 18 mm thick wood plastic composites (WPC) board, 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc. complete all as specified and as directed. Note:- (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

S&F continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified and as directed.

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength complete all as specified and as directed.

S&F stainless steel AISI 304 grade handle of size 75 mm long,etc. complete all as specified and as directed.

S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw complete all as specified and as directed.

Surface dressing n exc 15 cm deep complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm stone aggregate as in sub base complete all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block 60 mm thick any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade laid over and including 50mm thick sand cushioning complete all as specified and as directed.

S&F Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs/ truss and including Powder coated anodised aluminium snap grid frame size 605 x 605 mm and 2-3 mm thick for false ceiling complete all as specified and as directed.

S&F acoustic gypsum perforated board 4 mm thick of size 600x600 mm fixed in ceiling or laid/ inserted to Aluminium snap grid complete all as specified and as directed.

M&L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

Cutting holes in brick walls in built in cement mortar or cement lime mortar exc half brick but not exc one brick complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M&L for steel work in tubuler trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide, zink chrome primer including preparation of new steel surfaces of any description, not itherwise described, over 10 cm width or girth complete all as specified and as directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks strainght or curved on plan not exceeding 6m mean radius built in cement mortor 1:6, complete all as specified and as directed.

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and as directed.

Plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in coping and similar work etc. including weathering, slightly rounded or chamferred angles and throating and provision of necessary formwork complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) using 20mm graded aggregate as in footings, foundation, plinth beam, bases for columns, etc.; basement slabs, undreamed piles and mass concrete, etc. complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) using 20mm graded aggregate as in columns, pillars, piers, posts and struts, etc. complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) using 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, etc. complete all as specified and as directed.

Form work, rough finished conc surfaces to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter surfaces, etc. complete all as specified and as directed.

Form work, rough finished conc surfaces, to sides of pillars, post, struts, piers, columns & stanchions, etc. complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying two coat of exterior weather emulsion paint white or tinted over & including a coat of wall care Putty specified for external surface as per manufacturer instruction complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,over and including 15 mm thick screed bed in CM 1:6 in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 450x300x7 mm thick over and including 10 mm thick cement platser in CM 1:4 as in backing, set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F Ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed complete all as specified and as directed.

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and as directed.

S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe complete all as specified and as directed.

S&F 15 mm Angle valve/Stop valves, cast copper alloy, chromium palted, fancy type screwed down high pressure with crutch and butter fly handles, screwed with iron pipes or for union complete all as specified and as directed.

S&F bib tap, brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore complete all as specified and as directed.

S&F mixing valve 15 mm dia, CP brass fancy including joints to steel pipe or unions for centre hole wash hand basin, including fittings complete all as specified and as directed.

S&F chromium plated grating with 100mm dia of approved make includingh fixing with 1:4 CM to floor/ nahni trap etc. complete all as specified and as directed.

S&F grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc. complete all as specified and as directed.

S&F brass chromium plated overhead shower rose 125mm dia, with revolving joint and shower rod to fixed to 15mm bore pipe complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass CP complete all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device complete all as specified and as directed.

S&F PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity, low level, white, with inlet ball valves, float and handle including brackets and pvc flush pipe 32 mm dia for low level complete all as specified and as directed.

S&F vitreous china wash basin, white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets complete all as specified and as directed.

S&F factory made moulded solid PVC chowkhat/ door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with 19 mm x 19mm MS square tube of 19 gauge including rubber gasket, PVC fastners, screws, brackets, and shown on drawing as per SSR Part-II (2010) complete all as specified and as directed.

S&F factory made moulded solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tube for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail , lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at the site as per specification & drawing . on page no 161 of SSR part-II (2010) complete all as specified and as directed.

S&F stainless steel butt hinges, size 100 mm complete complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts, 150 mm long of extruded section and fixed complete all as specified and as directed.

S&F aluminium handles, 150 mm size, fabricated type complete all as specified and as directed.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mm x 44.45mm x 1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture/aluminum snap beads complete all as specified and as directed. Note: (a) Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately. (b) Cost of SS wire mesh and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid.

M&L for Machine cut Kota stone slab flooring 18-20mm thick over 20mm thick cement screed bed laid 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar, laid over cement screed 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

S&F 5 mm thick MS plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and as directed.

S&F in repairs 6 mm thik glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr-in-Charge/GE) complete all as specified and as directed.

S&F in repairs wash hand basin mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all as specified and as directed.

S&F in repairs Brass CP Wall mixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and as directed.

M&L for cement concrete chequered tiles with gray cement and pigment 25cm x 25cm x 20 mm thick, machine pressed, set, jointed and pointed in neat cement slurry in floors and cut and polished over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Excavation in post holes each in exc. 0.50cum getting out returning filling in and ramming earth in layers not exc. 25cm watering & removing surpius soil to a distance n exc. 50m & making good surface in hard/dense soil complete all as specified and as directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, fordoors, balusters, nosing to steps including embeding in concreteand screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire meshetc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for framed work as in doors or gates of angle or other section gusset plates, rails braces etc, drilled for fixing, and other covering door etc to be prepared for hanging and sliding with and including either hooks and hinges and steel hanging door fittings and other covering running rails and guides and hanging also fastening and fixing complete all as specified and as directed. Fe- 410 Grade E-250 quality-Bl.

S&F mild steel screw bolts (machine cut) with hexagonal or square heads at one end and screwed the outher or screwed both ends, each screwed end to be fitted with washers and one heragonal or square exc 5 cm but n.exc 10 cm long and 12 mm dia 75 mm long complete all as specified and as directed.

S&F Mild steel round bar 10 mm dia and over cut to length bend to shape required including cranking bending spirally for hopping for colours hooking ends and binding with a including security bolts post and struts in fencing including cutting top to shape as directed drilling holes notching for wire etc. complete all as specified and as directed.

Preparation of surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and as directed.

S&F chain link MS galvanised fencing 50 mm Square mesh with 10 gauges incl line wires any mesh size & type to any type of standards rails straining bolts etc. incl provision of binding wire complete all as specified and as directed.

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

S&F in repairs 32/40 mm bore and 750mm long PVC Waste pipe suitable for WHB /Sink/ urinal complete all as specified and as directed.

S&F 15 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors or concealed, complete all as specified and as directed.

S&F 20 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors or concealed, complete all as specified and as directed.

M&L for PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

S&F rolled mild steel work as in framed barred iron gates including all necessary drilling, bolting or riveting etc and similar work conforming to GDE Fe 410-0 or Fe 310-0 complete all as specified and as directed.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, strainig bolts, etc. including provision of binding wire complete all as specified and as directed.

M&L for preparation of newly steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Taking down chowkhats or frames with shutter exc 1.5 sqm and nexc 4.00 sqm each without taking off shutters from the frame incl removing complete all as specified and as directed.

All as per Srl item No.108 above, but nexc 1.5 Sqm

Dismantling wrought iron or mild steel work of any description not otherwise provided for windows grill complete all as specified and as directed.

M&L 6mm dia powder coated aluminium decco grill, (minimum thickness of powder coating 50 micron), section No-104, 100mm aperture of hexagonal design and pattern as approved complete all as specified and as directed.

M&L for Granite (of any type) tiles 16 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete and including 15mm thick screed bed in cm 1:6 for laying floor finish complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primess complete all as specified and as directed.

Taking down shutter of any description exc 1.00 sqm nexc 2.00 sqm each and refixing the same opening including easing and adjusting the same complete all as specified and as directed.

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc. complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion, over a coat white or tinted over & including a coat of wall care putty complete all as specified and as directed.

M&L for preparation by complete removal of existing treatment , wahsing down and stopping of distempered and painted surfaces and old plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including a coat of wall care putty complete all as specified and as directed.

S&F in repairs brass CP Wall mixer for mixing Hot and cold water screwed down for iron pipe complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white round shape size 520x450x200 mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified and as directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding ditto but including brackets taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S&F in repairs chromium plated brass angle valve suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and as directed.

M&L in repairs soap dish chromium plated brass fixed with brass nuts and screws as in repair complete all as specified and as directed.

M&L for toilet paper holder brass chromium plated as in repair complete all as specified and as directed.

S&F in repairs CP brass shower rose fancy type 125mm size suitable for 15mm bore pipe complete all as specified and as directed. specified.

S&F in repairs viterous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap and making good the disturbed surface to match with the existing complete all as specified and as directed.

S&F in repairs 12 mm thick prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

All as Srl item No. 127 abov,e but 18/19 mm thick.

Taking up or down 15mm bore steel tubing and connections, with all fittings and fixed complete from walls and ceilings or laid floors or walls complete all as specified and as directed.

S&F (width of flaps 30 mm) continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F precast factory made polycrete (SFRC) light duty man hole covers, 65mm thick, rectangular in shape upto 0.60 Sqm area with at least 5cm bearing on each side complete all as specified and as directed.

Plain cement concrete 1:2:4, type B-2, using 20mm graded stone aggregate as surface channel/drains inside the manholes and like including weathering, slightly rounded or chamfered angles and throating as directed and provision of necessary formwork to any extent and finished exposed surface even and smooth without using extra cement complete all as specified and as directed.

M&L for RCC (M-25 (Design Mix) using 20mm graded stone aggregate as in retaining wall etc. complete all as specified and as directed.

Form work, to faces of walls, retaining walls, abustments, and similar work etc. complete all as specified and as directed.

S&F 75 mm PVC (SWR) pipes Type 'A', in any length with rubber ring joints, fixed in RCC retaining walls complete all as specified and as directed.

M&L for point wiring complete with single core multi strand copper conductor 1.5 Sqm nominal area PVC insulated FRLS 1100 Volts grade electrical cable in and including concealed PVC conduit medium grade and Modular sunken pressed steel terminal box 2 mm thick required size including modular plate and modular flush box in different module with all accessories including 1.5 Sqm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and as directed. Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete. One light /fan/Bell point/security light controlled by one way switch

All as per Srl item No.136 above, but one socket outlet 15 Amps on independent board with cables 2.5 Sqmm size for phase and neutral and 2.5 Sqmm for earthing from main DB to provision geyser point.

All as per Srl item No.136 above, but one AC point on independent board with cables 4 Sqmm size for phase and neutral and 4 Sqmm for earthing from main DB to provision AC point.

S&F Switch Modular type switch, 6 A 1- way SP switch with finger proof terminal complete all as specified and as directed.

S&F AC/Geyser modular box with MCB 25 SP Amps complete all as specified and as directed.

S&F ceiling rose complete all as specified and as directed.

S&F Exhaust fan 300mm sweep against deficiency , 900 RPM, metallic body including metalic blade , single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 1.5 sqmm for connection from ceiling rose to fan complete all as specified and as directed. Note :- the rates is inclusive drilling hole /cutting /chasing and making good the disturbed surface with cm 1:3 and same surace finishes with adjoining surface of disturved area with OBD/colour wash/white wash.

S&F water storage heater, 5 star, Glass lined enamel coated incoloy heating element ,Digital temperature display, Feather touch buttons, Shock resistant injection moulded ABS body, IPX4 waterproof technology, Tank design is suitable to withstand 8 bar pressure (Geyser) of capacity 25 litre, , AC, electric, 230 volt, complete , 3 core lead, including PRCD Plug top, safety valve, including electric and water connection and making good to disturbed surface including With PVC hot & cold water flexible pipe, fashner of suitable size complete all as specified and as directed.

S&F MCB SP 6 to 32 Amps 240 Volts, 10kA, `B' curve all as per site requirement and complete all as specified and as directed.

Note :- The contract sum shall be after deducting the amount of credit shown in Sch of Credit of this tender

YP INFRA

Chaudhary Constructions

HANUMAN BUILDERS

verma enterprises